In Situ synthesis of multiblock copolymers of poly(ϵ‐caprolactone) with different poly(ether diols) based polyurethane by reactive extrusion

Polyurethanes with multiblock copolymers of poly(?‐caprolactone) (PCL) and poly(tetramethylene oxide) glycol (PTMG) or poly(ethylene glycol) (PEG) as a soft segment were synthesized in situ via reactive extrusion from ?‐caprolactone (CL) and 4,4′‐diphenylmethane diisocyanate (MDI). The titanium alkoxide mixture generated from an ester‐exchange reaction between titanium propoxide [Ti(OPr)₄], and excessive PTMG or PEG was used as an initiator and catalyst. Compared to the reported fabrication of polycaprolactone‐based polyurethane (PCLU), the in situ reactive extrusion preparation not only explored a new rapid route for the fabrication of PCLU but also offered a simplified, controllable approach for the production of PCLU in a successive mass scale. A series of PTMG–PCLUs and PEG–PCLUs with different PCL block‐average degrees of polymerization (DP_n's) were prepared by only an adjustment of the relative concentration of CL in the reaction system, with a certain constant molar ratio of MDI to titanium alkoxide. ¹H‐NMR, gel permeation chromatography, and differential scanning calorimetry results indicate that all of the CL monomers were converted in the polymerization, and the molecular weight of the copolymers was about 8 × 10⁴ g/mol with a polydispersity index of approximate 2.4. With an increase in the PCL block‐average DP_n in PTMG–PCLU from 25 to 40, the tensile strength increased from 16.5 to 22.7 MPa, and the melting point increased from 46.1 to 49.5°C. It was also verified by PEG–PCLU prepared with organic Ti of lowered content in the initiator mixture that the mechanical properties could be greatly affected and dropped with decreasing content of organic Ti in the initiator mixture. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Soft segmental effect of methylene bis(p‐cyclohexyl isocyanate) based thermoplastic polyurethane impregnated with lithium perchlorate/propylene carbonate on ionic conductivity

Thermoplastic polyurethane (TPU) was employed as the polymer matrix for ion conduction as gelled electrolytes with lithium perchlorate (LiClO₄) in propylene carbonate (PC) solution. The TPU was prepared by methylene bis(p‐cyclohexyl isocyanate) as the hard segment while employing both poly(ethylene glycol) (PEG) and poly(tetramethylene glycol) (PTMG) as the soft segments. The copolymer comprising both PEG and PTMG was prepared such that it possessed the combined characteristics of good conductivity from the former and good mechanical properties from the latter. All the polymers were characterized by gel permeation chromatography, differential scanning calorimetry, and Fourier transform IR spectroscopy. The conductivity data were obtained from alternating current impedance experiments. The results revealed that the copolymer containing both PEG and PTMG as the soft segments showed better performance than TPU containing either PEG or PTMG. The copolymer TPU(PEG/PTMG) proved to be a good gelled electrolyte from 5 to 85°C. This copolymer, impregnated with 150% LiClO₄/PC, possessed good mechanical strength and conductivity as high as 10^?3 S/cm. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 935–942, 2001     

Synthesis of polyacrylonitrile via reverse atom transfer radial polymerization (ATRP) initiated by diethyl 2,3‐dicyano‐2,3‐diphenylsuccinate,FeCl3, and triphenylphosphine

The reverse atom transfer radical polymerization (RATRP) technique using FeCl₃/triphenyl‐phosphine (PPh₃) complex as a catalyst was applied to the living radical polymerization of acrylonitrile (AN). A hexa‐substituted ethane thermal iniferter, diethyl 2,3‐dicyano‐2,3‐diphenylsuccinate (DCDPS), was first used as the initiator in this iron‐based RATRP initiation system. A FeCl₃ to PPh₃ ratio of 1:3 not only gives the best control of molecular weight and its distribution but also provides a rather rapid reaction rate. The rate of polymerization increases with increasing the polymerization temperature and the apparent activation energy was calculated to be 54.9 kJ mol^?1. Because the polymers obtained were end‐functionalized by chlorine atoms, they were used as macro‐initiators to proceed the chain extension polymerization in the presence of an FeCl₂/PPh₃ catalyst system via a conventional ATRP process. Copyright © 2005 Society of Chemical Industry     

Synthesis of polyacrylonitrile via reverse atom transfer radical polymerization initiated by 1,1,2,2‐tetraphenyl‐1,2‐ethanediol/FeCl3/triphenylphosphine

FeCl₃ coordinated by triphenylphosphine was first used as the catalyst in the 1,1,2,2‐tetraphenyl‐1,2‐ethanediol‐initiated reverse atom transfer radical polymerization of acrylonitrile. A FeCl₃/triphenylphosphine ratio of 0.5 not only gave the best control of the molecular weight and its distribution but also provided a rather rapid reaction rate. The rate of polymerization increased with increasing polymerization temperature, and the apparent activation energy was calculated to be 62.4 kJ/mol. When FeCl₃ was replaced with CuCl₂, the reverse atom transfer radical polymerization of acrylonitrile did not show prominent living characteristics. To demonstrate the active nature of the polymer chain end, the polymers were used as macroinitiators to advance the chain‐extension polymerization in the presence of a CuCl/2,2′‐bipyridine catalyst system via a conventional atom transfer radical polymerization process. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 4041–4045, 2007     

Fe‐mediated ARGET atom transfer radical polymerization of methyl methacrylate in ionic liquid‐based microemulsion

Poly(methyl methacrylate) (PMMA) was synthesized by activator regenerated by electron transfer (ARGET) atom transfer radical polymerization (ATRP) of MMA in ionic liquid‐based microemulsion with polyoxyethylene sorbitan monooleate (Tween 80) as surfactant. The polymerization was carried out at 25°C with CCl₄ as initiator, FeCl₃·6H₂O/N,N,N′,N′‐tetramethyl‐1,2‐ethanediamine (TMEDA) as catalyst complex in the presence of reducing agent ascorbic acid (VC). The polymerization kinetics showed the feature of controlled/″living″ process as evidenced by a linear first‐order plot. The well‐controlled polymers were obtained with narrow polydispersity indices and the ionic liquid‐based microemulsions were transparent with a particle size less than 30 nm. The obtained polymer was characterized by ¹H NMR and gel permeation chromatography. The chain extension was successfully achieved by the obtained PMMA macroinitiator/FeCl₃·6H₂O/TMEDA/VC initiator system based on ARGET ATRP method. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

An iron‐based reverse ATRP process for the living radical polymerization of acrylonitrile

A hexa‐substituted ethane thermal iniferter, diethyl‐2,3‐dicyano‐2,3‐di(p‐tolyl) succinate (DCDTS), was firstly used as the initiator in the reverse atom transfer radical polymerization (RATRP) of acrylonitrile. FeCl₃ coordinated by isophthalic acid (IA) was used as the catalyst in this system. The polymerization in N,N‐dimethylformamide not only shows the best control of molecular weight and its distribution but also provides rather rapid reaction rate with the ratio of [AN] : [DCDTS] : [FeCl₃] : [IA] at 500 : 1 : 2 : 4. The polymers obtained were end‐functionalized by chlorine atom, and they were used as macroinitiators to proceed the chain extension polymerization in the presence of FeCl₂/IA catalyst system via a conventional ATRP process and polyacrylonitrile obtained was with M_n = 39,260, PDI = 1.25. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Lanthanide(II) amide complexes: Efficient initiators for the living polymerization of methyl methacrylate

Lanthanide(II) complexes supported by amido ligands, [(C₆H₅)(Me₃Si)N]₂Ln(DME)₂ [Ln = Sm ( 1 ) or Yb ( 2 ); DME = 1,2‐dimethoxyethane] and [(C₆H₃? ⁱPr₂‐2,6)(Me₃Si)N]₂Ln(THF)₂ [Ln = Sm ( 3 ) or Yb ( 4 ); THF = tetrahydrofuran], were found to initiate the polymerization of methyl methacrylate (MMA) as efficient single‐component initiators (in toluene for 3 and 4 and in toluene with a small amount of THF for 1 and 2 ) to produce syndiotactic polymers. The catalytic behavior was highly dependent on both the amido ligand and the polymerization temperature. Initiators 3 and 4 initiated MMA polymerization over a wide range of temperatures (20°C to ?40°C), whereas the polymerization with 1 and 2 proceeded smoothly only at low temperatures (≤0°C). The kinetic behavior and some features of the polymerizations of MMA initiated by 3 and 4 were studied at ?40°C. The polymerization rate was first‐order with the monomer concentration. The molar masses of the polymers increased linearly with the increase in the polymer yields, whereas the molar mass distributions remained narrow and unchanged throughout the polymerization; this indicated that these systems had living character. A polymerization mechanism initiated by bimetallic bisenolate formed in situ was proposed. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Reverse atom transfer radical polymerization of acrylonitrile under microwave irradiation

Reverse atom transfer radical polymerization was first used to successfully synthesize polyacrylonitrile under microwave irradiation. FeCl₃, coordinated by isophthalic acid, was used as the catalyst, and 2,2′‐azobisisoheptonitrilewas used as the initiator. N,N‐Dimethylformamide was used as the solvent to improve the solubility of the ligand. Under the same experimental conditions, the apparent rate constant under microwave irradiation was higher than that under conventional heating. The polymerization not only showed the best control of the molecular weight and its distribution but also provided a rather rapid reaction rate with the [acrylonitrile]/[2,2′‐azobisisoheptonitrile]/[FeCl₃]/[isophthalic acid] ratio of 300 : 1 : 1 : 2. The polymers obtained were used as macroinitiators to initiate the chain extension and successfully synthesize acrylonitrile polymers with a molecular weight higher than 50,000 and a narrow polydispersity as low as 1.30. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Vinyl ethers with polysulfide and hydroxyl functions and polymers therefrom as binders for lithium–sulfur batteries

Bis‐[3‐(vinyloxyethoxy)‐2‐hydroxypropyl‐]polysulfides (BVPS) have been prepared by reacting ethylene glycol vinyl glycidyl ether (EGVGE) with Na₂S₄ in the presence of NaHCO₃ and a phase transfer catalyst, triethylbenzylammonium chloride. The polysulfides obtained are inactive in radical polymerization but polymerize readily upon thermal initiation (140°C, 1 h) or in the presence of cationic catalysts [BF₃·OEt₂, CF₃COOH, H(AuCl₄)·4H₂O, LiBF₄‐dimethoxyethane, 20–70°C]. Polymerization leads to the formation of crosslinked polymers. It has been shown that BVPS and their polymers can be used as active binders in cathode compositions of lithium–sulfur power sources. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 4051–4055, 2006     

ATRP of acrylonitrile catalyzed by FeCl2/succinic acid under microwave irradiation

A single‐pot atom‐transfer radical polymerization (ATRP) under microwave irradiation was first used to successfully synthesize polyacrylonitrile. This was achieved by using FeCl₂/succinic acid as the catalyst and 2‐chloropropionitrile as the initiator. Using the same experimental conditions, the apparent rate constant under microwave irradiation was found to be higher than that under conventional heating. The FeCl₂/succinic acid ratio of 1 : 2 not only gives the best control of molecular weight and its distribution but also provides rather rapid reaction rate. When FeCl₂ was replaced with CuCl, ATRP of AN does not show an obvious living characteristics. To demonstrate the active nature of the polymer chain end, the polymers were used as macroinitiators to proceed the chain‐extension polymerization. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1598–1601, 2006     

Reverse ATRP of acrylonitrile with diethyl 2,3-dicyano-2,3-diphenyl succinate/FeCl3/iminodiacetic acid

The reverse atom transfer radical polymerization (RATRP) technique using FeCl₃/iminodiacetic acid (IMA) complex as a catalyst was applied to the living radical polymerization of acrylonitrile (AN). A hexa-substituted ethane thermal initiator, diethyl 2,3-dicyano-2,3-diphenylsuccinate (DCDPS), was firstly used as the initiator in this iron-based RATRP system. The polymerization in N,N-dimethylformamide not only shows the best control of molecular weight and its distribution but also provides rather rapid reaction rate with the ratio of [AN]:[DCDPS]:[FeCl₃]:[IMA] at 500:1:2:4. The rate of polymerization increases with increasing the polymerization temperature and the apparent activation energy was calculated to be 49.9 kJ mol⁻¹. The polymers obtained were end-functionalized by chlorine atom, and they were used as macroinitiators to proceed the chain extension polymerization in the presence of FeCl₂/IMA catalyst system via a conventional ATRP process. The resultant polyacrylonitrile fibers were obtained with the fineness at 1.16 dtex and the tenacity at 6.01cN dtex⁻¹.     

Synthesis of cross‐linked polyethylene oxide‐acetal macrocycles for solid superbase catalysts

A novel long‐chain divinyl ether of tris(diethyleneglycol)‐bisacetal, has been synthesized by electrophilic addition of one molecule of diethylene glycol to two molecules of divinyl ether of diethylene glycol (DVDEG) in the presence of CF₃COOH in quantitative yield. The monomer was cationically polymerized (BF₃·OEt₂, or complex LiBF₄·MeO(CH₂)₂OMe) and copolymerized with DVDEG to deliver solid polymers the yields being 80–100%. The polymers represent the cross‐linked polyether‐polyacetal structures comprising macrocycles. The polymers were treated with 3% solution of KOH or CsOH in methanol to afford solid superbase complexes of KOH (CsOH) with cross‐linked polyether‐polyacetal macrocyclic networks. Preliminary tests have shown the complexes to be active catalysts for ethynylation of acetones and prototropic isomerization of methyl propargyl ethers to allenyl methyl ethers. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

‘Living’ radical polymerization of styrene with AIBN/FeCl3/PPh3 initiating system via a reverse atom transfer radical polymerization process

Well‐defined polystyrenes with an α‐C(CH₃)₂(CN) and an ω‐chlorine atom end‐groups, and narrow polydispersity (M_n = 3000–4000 g mol⁻¹, M_w/M_n = 1.3–1.4) have been synthesized by a radical polymerization process using 2,2′‐azobisisobutyronitrile(AIBN)/FeCl₃/PPh₃ initiation system. When the ratio of [St]₀:[AIBN]₀:[FeCl₃]₀:[PPh₃]₀ is 200:1:4:12 at 110 °C, the radical polymerization is ‘living’, but the molecular weight of the polymers is not well‐controlled. The polymerization mechanism belongs to a reverse atom transfer radical polymerization (ATRP). Because the polymer obtained is end‐functionalized by a chlorine atom, it can then be used as a macroinitiator to perform a chain extension polymerization in the presence of CuCl/2,2′‐bipyridine catalyst system via a conventional ATRP process. The presence of a chlorine atom as an end‐group was determined by ¹H NMR spectroscopy. © 2000 Society of Chemical Industry     

结构调节剂对液体异戊二烯聚合的影响

采用锂系阴离子聚合工艺合成液体异戊二烯橡胶( LIR),在聚合过程中添加5种不同的结构调节剂,研究他们对LIR结构的影响。结果表明：非极性调节剂二硫化碳(CS₂)对LIR顺-1,4含量的影响不大;极性调节剂均可降低顺-1,4含量。其中二乙二醇二甲醚(2G)、四甲基乙二胺(TMEDA)对顺-1,4含量的调节作用较大;乙醚(Et₂O)对顺-1,4含量的调节作用较小;四氢呋喃(THF)作为结构调节剂效果最好。     

Synthesis and self-assembly of poly(benzyl ether)-b-poly(methyl methacrylate) dendritic-linear polymers

Here, the dendritic chloric poly(benzyl ether) (G₁-Cl, G₂-Cl and G₃-Cl) as the macroinitiator for the controlled atom transfer radical polymerization (ATRP) of methyl methylacrylate was investigated. Polymers obtained were characterizated by GPC, ¹H NMR, FT-IR, TGA and DSC. These dendritic-linear block polymers that consist of linear and dendritic segments have very good solubility in common organic solvents at room temperature. In a selective solvent (THF/H₂O), polymers can self-assembled into the micelles that have a spherical morphology in shape due to the lowest of the surface energies.     

AlCl3 promoting living-radical polymerization of MMA based on sec-butyl chlorine in n-butanol

The effect of metal halide AlCl₃ as additive on the living-radical polymerization of methyl methacrylate (MMA) in n-butanol at 80 °C was investigated. The initiator was sec-butyl chlorine (SBC), which was used as a model initiator containing secondary R-Cl bond and the catalyst was FeCl₂/(PPh₃)₄. The polymerization reaction of MMA, using SBC/FeCl₂ (PPh₃)₄ as initiating system, was very slow or even did not take place without AlCl₃. The addition of AlCl₃ accelerated the polymerization to some great extent and the polymers obtained have almost controlled molecular weights and narrow molecular weight distribution. These experimental results were different from those of the literatures, in which metal chlorides would slow down the polymerization rate of MMA for ATRP reactions.     

Anionic ring‐opening polymerization of adipic anhydride initiated by potassium poly(ethylene glycol)ate

Poly(adipic anhydride) (PAA) was prepared by the ring‐opening polymerization of adipic anhydride (AA) initiated by potassium poly(ethylene glycol)ate. The effects of various factors, such as the amount of initiator, concentration of the monomer, reaction time and temperature, and polarity of the solvent on the polymerization were investigated. The crude polymerized product was a mixture of PAA homopolymer and poly(ethylene glycol)–poly(adipic anhydride) block copolymer, as confirmed by ¹H‐NMR and gel permeation chromatography. Chain‐transfer reactions occurred intensively for the AA polymerization in both the nonpolar solvent toluene and the polar solvents CHCl₃ and tetrahydrofuran, which predominantly determined the molecular weight and the monomer conversion for the polymerized product. The lower monomer conversion in toluene was ascribed to a lower livingness for the initiator in the nonpolar solvent when compared with other two, polar solvents. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2194–2201, 2003     

Reverse atom‐transfer radical polymerization of acrylonitrile catalyzed by FeCl3/iminodiacetic acid

FeCl₃ coordinated by iminodiacetic acid (IMA) was Changed used for the first time as the catalyst in azobisisobutyronitrile‐initiated reverse atom‐transfer radical polymerization (ATRP) of acrylonitrile (AN). An FeCl₃ to IMA ratio of 1:2 not only gave the best control of molecular weight and its distribution but also provided a rather rapid reaction rate. The effects of solvents on the polymerization of AN were also investigated. The rate of the polymerization in N,N‐dimethylformamide (DMF) was faster than in propylene carbonate or toluene. The molecular weight of polyacrylonitrile agreed reasonably well with the theoretical molecular weight in DMF. The rate of polymerization increased with increasing polymerization temperature and the apparent activation energy was calculated to be 54.8 kJ mol⁻¹. The reverse ATRP of AN did not show obvious living characteristics with CuCl₂ instead of FeCl₃. Copyright © 2005 Society of Chemical Industry     

Kinetic study of the atom transfer radical polymerization of n‐docosyl acrylate

The atom transfer radical polymerization (ATRP) of n‐docosyl acrylate (DA) was studied at 80°C in N,N‐dimethylformamide using the carbon tetrabromide/FeCl₃/2,2′‐bipyridine (bpy) initiator system in the presence of 2,2′‐azobisisobutyronitrile (AIBN) as the source of reducing agent. The rate of polymerization exhibits first‐order kinetics with respect to the monomer. The linear relationship between the molecular weight of the resulting poly(n‐docosyl acrylate) with conversion and the narrow polydispersity of the polymers indicates the living characteristics of the polymerization reaction. The significant effect of AIBN on the ATRP of DA was studied keeping [FeCl₃]/[bpy] constant. A probable reaction mechanism for the polymerization system is postulated to explain the observed results. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 2147–2154, 2005     

Effects of catalyst on sequence distribution and transparency of poly(tetramethylene terephthalate)–poly(tetramethylene ether) segmented copolymers

Polyether-polyester segmented copolymer based on hard segments of tetramethylene terephthalate (PBT) and soft segments of poly(tetramethylene ether glycol) (PTMG) was synthesized by four kinds of catalyst: tetrabutyl titanate and magnesium acetate (Ti-Mg); tetrabutyl titanate and triethanolamine; tetra(isopropyl) titanate; and isopropoxy(triethanolaminato) titanate, respectively. Their segment sequence distributions were analyzed by ¹³C-NMR, based on different chemical shifts of aromatic quaternary carbons in the three different triad sequences. The effects of catalyst on sequence distribution and transparency were investigated. It was found that the copolymer has lower probability of B-T-B when Ti-Mg was used as catalysts, and results in higher transparency. © 1995 John Wiley & Sons, Inc.