Controlled synthesis of poly(vinyl acetate) by traditional radical emulsion polymerization

A new redox initiation system, potassium persulfate/N,N‐dimethylethanolamine, was used to initiate traditional radical emulsion polymerization of vinyl acetate at low temperature. Polymers were characterized using gel permeation chromatography, scanning electron microscopy and dynamic light scattering. The results showed that poly(vinyl acetate) with high molar mass and small dispersity (?) was successfully synthesized. © 2016 Society of Chemical Industry     

Synthesis of high-molecular weight poly(vinyl alcohol) by low-temperature emulsifier-free emulsion polymerization of vinyl acetate and saponification

High-molecular weight (HMW) poly(vinyl alcohol) (PVA) was prepared via an emulsifier-free emulsion polymerization of vinyl acetate (VAc) using a redox initiation system in low temperatures, and the subsequent saponification with potassium hydroxide in methanol. The effect of the polymerization conditions on the conversion, molecular weight, and branching degree was investigated. PVA with maximum viscosity-average degree of polymerization (DP) of 8270 could be prepared by saponification of poly(vinyl acetate) (PVAc), with DP of 10,660 obtained at temperature of 10°C, monomer concentration of 30%, potassium persulfate molar ratio to monomer of 1/2000, agitation speed of 160 rpm. The conversion was above 90%. From the emulsifier-free emulsion polymerization of VAc in low temperature, PVAc with HMW and high linearity was effectively prepared, which might be useful for the preparation of high-strength and high-modulus PVA fiber. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Studies on the miscibility and phase structure in blends of poly(epichlorohydrin) and poly(vinyl acetate)

The miscibility of atactic poly(epichlorohydrin) (aPECH) with poly(vinyl acetate) (PVAc) was examined under two different conditions: (i) in dilute solution, using vicometeric measurements and (ii) as cast films, using differential scanning calorimetric (DSC) and FT-infrared spectroscopy. Phase separation on heating, i.e. lower critical solution temperature (LCST) behavior of the aPECH/PVAc blends was examined by the measurement of transmitted light intensity against temperature. From viscosity measurements, the Krigbaum-Wall polymer-polymer interaction (ΔB) was evaluated. The DSC results show that the aPECH/PVAc blends are miscible as evidenced by the observation of a single composition-dependent glass-transition temperature (T_g) which is well described by the Couchman and Gordon Taylor models. The Flory-Huggins interaction parameter (χ₁₂) calculated from the T_g-method was negative and equal to −0.01, indicating a relatively low interaction strength. The FT-IR results match very well with those of DSC. The cloud point phenomenon is thermodynamically driven but phase separation, once taken place, is diffusion controlled in normal accessible time.     

Effect of tacticity of poly(methyl methacrylate) on the miscibility with poly(vinyl acetate)

The results of the miscibility between the chemically similar polymers poly(methyl methacrylate) (PMMA) and poly(vinyl acetate) (PVAc) published so far show inconsistent statements concerning miscibility. The problems may be due to differences in molecular weights, tacticity, and preparation methods of the polymers. This investigation was carried out by using either chloroform or tetrahydrofuran (THF) as solvent to prepare the blends, because to our knowledge, nobody has reported any tacticity effect of PMMA on the miscibility with PVAc. Therefore, in this article, different tactic PMMAs were used to mix with PVAc and their miscibility was studied calorimetrically. The results showed little effect of solvent and tacticity. PMMA and PVAc were determined to be almost completely immiscible because of the observation of two T_g's. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 35–39, 2004     

Diffusion of solvents in poly(vinyl acetate) and partially and fully hydrolyzed poly(vinyl alcohol)

Diffusivities of methyl acetate, methanol and water in poly(vinyl acetate) and fully and partially hydrolyzed poly(vinyl alcohol) have been measured by capillary column inverse gas chromatography and/or gravimetric sorption. Data from the literature have been used when available for comparison. Overall the diffusivities show good consistency in terms of their temperature and concentration dependences. The free‐volume model has been applied to all the data with excellent results. In most cases the dramatic changes in diffusivities with temperature and concentration can be captured using only a few experimental data points and two regression parameters. This demonstrates that the free‐volume theory is a valuable tool for the design of equipment for processing and devolatilization of polymer ? solvent systems. © 2013 Society of Chemical Industry     

Crosslinking of poly(vinyl acetate) nanolatices by gamma and UV radiation

Poly(vinyl acetate) PVAc, in nanolatices with 10% polymer content, prepared by microemulsion polymerization was crosslinked by gamma and UV radiation. PVAc colloidal nanoparticles (average diameter, Dp = 58 nm) had M_w = 562,000 g/mol and about 95% conversions. PVAc nanolatices irradiated by gamma rays (1–13 kGy) at room temperature without crosslinking agent and by UV light (30–300 s exposure times) in the presence of divinylbenzene and allyl methacrylate showed crosslinking of up to 96% (high gel content), Dp < 100 nm and did not degrade as shown by FTIR spectroscopy. DSC and TGA characterization of irradiated PVAc samples indicated that T_g temperatures increased from 28°C for PVAc to 42°C and 39°C for UV and gamma rays crosslinked PVAc, respectively, whereas 10% weight losses occurred at 261°C for uncrosslinked PVAc and at 320 and 313°C for UV and gamma rays crosslinked PVAc. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Fibrous membranes of cellulose acetate and poly(vinyl pyrrolidone) by electrospinning method: Preparation and characterization

Fibrous membranes of cellulose acetate (CA), poly(vinyl pyrrolidone) (PVP) and composite membranes of these polymers, were obtained by the electrospinning method. Using systematic method, the optimal conditions for preparation of fibrous membranes were found. Both CA and PVP a concentration of 8% weight was found. The CA was dissolved in a acetone:water solution, volume ratio 80 : 20 and the PVP is dissolved in ethanol:water solution, ratio volume 85 : 15. The flow rate for both polymers was 1.5 mL h^?1. The same applied voltage value and the distance between the needle and collection plate were for polymer both, 15 kV and 15 cm respectively. The morphology of fibrous membranes and composite membranes were evaluated by scanning electron microscopy (SEM). The CA fibers showed ribon morphology, while the PVP fibers were cilindric, in both cases with diameters in the micrometer range. Thermogravimetric analysis showed that CA had a complete degradation to 445°C, while the fibrous membranes PVP required a value of temperature for degradation of up to 571°C. Fibrous composite membrane PVP/CA/PVP shows a higher value of strain at break (%), and a lower value of tensile strength (MPa) compared to CA/PVP/CA. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Thermal characterization of poly(vinyl chloride) samples prepared by living radical polymerization: Comparison with poly(vinyl chloride) prepared by free radical polymerization

Poly(vinyl chloride) (PVC) samples were synthesized by a living radical polymerization (LRP) method and compared with commercial PVC prepared by the conventional free radical polymerization (FRP). The differences were assessed, for the first time, in terms of viscosimetry parameters and thermal analysis. The LRP method used to prepare the PVC‐LRP samples is the only one available to obtain this polymer free of structural defects, being of commercial interest in a view of preparing a new generation of PVC‐based polymer with outstanding performance. The polymerization temperature selected (35°C) to prepare the LRP samples is currently used in the industry to prepare PVC‐FRP grades with moderate to high molecular weight. Since the thermal stability is a direct consequence of the polymer structure, this study is of vital importance to understand the potential of new PVC‐LRP. The thermoanalytical measurements demonstrate an enhanced thermal stability of PVC‐LRP when compared with its FRP counterpart. The PVC‐LRP sample with very low molecular weight reveals a higher thermal stability than the most stable PVC‐FRP sample. It is the first report dealing with thermal analysis of PVC prepared by LRP. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Graphene network enabled high speed electrical actuation of shape memory nanocomposite based on poly(vinyl acetate)

Here strong electroactive shape memory nanocomposites were prepared by incorporating graphene nanoplatelets into poly(vinyl acetate) (PVAc ) through the simple solvent mixing method. TEM and XRD revealed that well exfoliated graphene nanoplatelets formed a continuous network throughout the matrix with a large amount of interconnectedness. Dynamic mechanical analysis showed that the inclusion of graphene significantly improves both glassy and rubbery moduli of the matrix. Furthermore, the prepared nanocomposites demonstrated a marked electrical conductivity up to 24.7 S m^?1 and thereby surprisingly rapid electrical actuation behaviour exhibiting a 100% recovery ratio in 2.5 s. Moreover, PVAc and its nanocomposites displayed scratch self‐healing capability. This work demonstrates that the PVAc /graphene nanocomposites with high modulus and excellent electroactive shape memory performance can be a promising material in many applications such as sensors and fast deployable and actuating devices. © 2016 Society of Chemical Industry     

Phase behavior and properties of poly(methyl methacrylate)/poly(vinyl acetate) blends prepared via in situ polymerization

Polymer blends composed of poly(methyl methacrylate) (PMMA) and poly(vinyl acetate) (PVAc) were prepared via radical-initiated polymerization of methyl methacrylate (MMA) in the presence of PVAc. Differential scanning calorimetry and dynamic mechanical analysis were employed to investigate the miscibility and phase behavior of the blends. The PMMA/PVAc blends of in situ polymerization were found to be phase separated and exhibited a two-phase structure, although some chain transferring reaction between the components occurred. The phase separation resulted from the solvent effect of MMA during the in situ polymerization, which was confirmed by the investigation of phase behavior based on solution cast blending. Solubility analysis of the polymerized blends indicated that some chain transferring reaction between the components occurred during the polymerization. An abrupt increase in gel content from 21.2 to 72.4 wt % was observed when the inclusion of PVAc increased from 30 to 40 wt %, and the gel component consisted of the component polymers as shown by infrared spectroscopy studies. The thermogravimetric analysis study indicated that the inclusion of a small amount of PVAc gives rise to a marked stabilization effect on the thermal stability. The PMMA/PVAc blends exhibited increased notched impact properties with the inclusion of 5 wt % PVAc. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 675–684, 1998     

低聚合度、低醇解度聚乙烯醇的合成与性能研究——I.低聚合度聚醋酸乙烯酯的合成

以甲醇为溶剂,偶氮二异丁腈(AIBN)为引发剂,采用自由基聚合方法合成了低聚合度聚醋酸乙烯酯,并对其结构进行了表征。讨论了聚合时间、引发剂用量、物料配比、聚合温度等因素对聚合率的影响,获得了相对较佳的工艺参数。     

两亲性聚乙烯醇-b-聚苯乙烯嵌段共聚物的合成及表征

采用原子转移自由基聚合(ATRP)法合成了具有两亲性的聚乙烯醇-b-聚苯乙烯嵌段共聚物P(VA-b-St)。首先利用调聚反应制备了带三氯甲基端基的聚醋酸乙烯大分子引发剂。以联二吡啶作配体、氯化亚铜为催化剂,引发苯乙烯单体聚合,得到结构明确的P(VAc-b-St)嵌段共聚物,而后通过皂化反应将其水解,从而得到两亲性嵌段共聚物P(VA-b- St);产物采用FT-IR、1H NMR、GPC等方法进行结构表征。P(VA-b-St)在不同浓度溶剂中的自组装行为用TEM进行了观察,结果表明:P(VA-b-St)可在DMF溶剂中形成球状囊泡结构,其尺寸达到纳米级。     

Dispersion of graphene nanoplatelets in poly(vinyl acetate) latex and effect on adhesive bond strength

Graphene nanoplatelets (GNPs) were directly dispersed in poly(vinyl acetate) (PVAc) latex in concentrations from 0.05 up to 2 wt% (based on dry weight), without using additional surfactants or dispersants. Stable dispersions were obtained due to interaction of the GNPs with protective colloids (poly(vinyl alcohol) and hydroxyethylcellulose) originally present in the latex. This caused an increase in viscosity and accentuated the pseudoplastic behavior of the latex, as evidenced by rheological measurements. Cryo‐SEM imaging showed that individual nanoplatelets were present in the aqueous phase. The equilibrium contact angle for water on dry PVAc films increased by 13° upon incorporation of 0.1 wt% GNPs due to the nanofiller hydrophobicity. However, this increase was lower for higher loadings, probably due to the occurrence of GNP agglomeration. Bond strength measurements performed with an automated bonding evaluation system setup on veneer lap joints showed more than 50% shear strength increase with incorporation of only 0.1–0.3 wt% GNPs. At higher loadings the bond strength decreased, indicating less efficient nanofiller dispersion in the polymer matrix. Raman spectroscopy analysis confirmed that GNP agglomeration was more significant at higher loadings.     

Synthesis of random and block copolymers of vinyl chloride and vinyl acetate by RAFT miniemulsion polymerizations mediated by a fluorinated xanthate

Reversible addition–fragmentation chain transfer miniemulsion (co)polymerizations of vinyl acetate (VAc) and vinyl chloride (VC) are conducted in the presence of a fluorinated xthanate (X1). VAc miniemulsion polymerization can be well controlled by X1, and PVAc with small polydispersity index (PDI, <1.20) are obtained. X1 also shows well mediative effect to VC‐VAc miniemulsion copolymerization, while the PDI of VC‐VAc copolymer is greater than that of PVAc since a chain transfer rate to VC is greater than that to VAc. PVAc‐b‐PVC copolymers are synthesized by VC miniemulsion polymerizations mediated by X1‐terminated PVAc. PDIs of PVAc‐b‐PVC copolymers are greater than that of PVAc and VC‐VAc random copolymers with close monomer compositions, and increase with the increase of VC conversion. This is caused by the increased chain transfer to monomer and the formation of monomer‐rich and polymer‐rich phases during the VC polymerization stage. As‐prepared PVAc‐b‐PVC copolymers exhibit a micro‐phase separated morphology. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45074.     

Synthesis and characterization of poly(vinyl chloride‐co‐vinyl acetate)‐graft‐poly[(meth)acrylates] by atom transfer radical polymerization

The graft polymerization of methyl methacrylate and butyl acrylate onto poly(vinyl chloride‐co‐vinyl acetate) with atom transfer radical polymerization (ATRP) was successfully carried out with copper(I) thiocyanate/N,N,N′,N′,N″‐pentamethyldiethylenetriamine and copper(I) chloride/2,2′‐bipyridine as catalysts in the solvent N,N‐dimethylformamide. For methyl methacrylate, a kinetic plot of ln([M]₀/[M]) (where [M]₀ is the initial monomer concentration and [M] is the monomer concentration) versus time for the graft polymerization was almost linear, and the molecular weight of the graft copolymer increased with increasing conversion, this being typical for ATRP. The formation of the graft polymer was confirmed with gel permeation chromatography, ¹H‐NMR, and Fourier transform infrared spectroscopy. The glass‐transition temperature of the copolymer increased with the concentration of methyl methacrylate. The graft copolymer was hydrolyzed, and its swelling capacity was measured. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 183–189, 2005     

Phase separation of unsaturated polyester resin blended with poly(vinyl acetate)

The behavior of phase separation during the curing reaction of unsaturated polyester (UPE) resin in the presence of low profile additive, that is, poly(vinyl acetate) (PVAc), was studied by low-angle laser light scattering (LALS) and scanning electron microscopy (SEM). The experimental results revealed that the PVAc-rich phase was regularly dispersed in the cured styrene–UPE matrix for styrene–UPE resin blended with 5 wt % of PVAc. As the PVAc content was increased higher than 10 wt %, a cocontinuous PVAc and cured styrene–UPE phase was observed for the cured systems. The LALS observations were carried out in situ at a curing temperature of 100°C; thus, the effect of the rate of exothermic heat released from curing reaction on the morphology of curing system was investigated and reported in this work. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 2413–2428, 1999     

Removal of sodium acetate in poly(vinyl alcohol) and its quantification by 1H NMR spectroscopy

A major impurity in poly (vinyl alcohol) (PVA) is sodium acetate which remains after its preparation by a base catalyzed hydrolysis of poly(vinyl acetate), and the amount of sodium acetate in commercial PVA samples may reach several percentages. To establish an optimal condition for the removal of sodium acetate, several washing parameters such as washing period, solvent polarity, and temperature were investigated in this study. Nuclear magnetic resonance (NMR) spectroscopy was successfully applied to determine the residual amounts of sodium acetate in the purified poly(vinyl alcohol). The relative integral value for the methyl peak of sodium acetate in PVA was converted to a relative mass value and finally to the sodium acetate content contained in PVA. The results showed that over 95% of sodium acetate in PVA was removed by a washing of PVA with distilled water within 2 h. When methanol was used as a washing solvent, a higher temperature than room temperature was required for an effective removal of sodium acetate. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

超临界二氧化碳-共溶剂体系与聚醋酸乙烯酯相互作用

采用多尺度模拟和实验结合研究了乙醇、丙酮、正庚烷等共溶剂的加入对超临界二氧化碳（CO₂）溶剂体系的影响,通过改善溶剂-溶剂和溶剂-溶质相互作用增强聚醋酸乙烯酯（PVAc）与CO₂的相容性。量子力学从头算结果表明,3种共溶剂中乙醇与CO₂的相互作用最强,丙酮次之,正庚烷最弱。分子动力学模拟也表明在相同共溶剂含量下,乙醇对溶剂体系溶解度参数的改善最为明显,超临界CO₂-乙醇体系与PVAc链的相互作用更强,有助于提高PVAc与溶剂的相容性。这是由于乙醇本身的溶解度参数较大,且与CO₂形成氢键作用,从而大幅增强了其与CO₂的相互作用。浊点压力实验证实了共溶剂的加入增强了超临界CO₂体系与PVAc的相容性,乙醇的加入对PVAc浊点压力的降低最为有效,且随着共溶剂含量的增加,PVAc在溶剂中的溶解能力增强。     

Influences of individual and composed poly(vinyl alcohol) suspending agents on particle morphology of suspension poly(vinyl chloride) resin

Effects of individual and composed poly(vinyl alcohol) (PVA) suspending agents on the particle morphology of poly(vinyl chloride) (PVC) resins were investigated and discussed in the view of PVA absorption at the oil/water interface and interfacial behavior. It was shown that the percentage and surface coverage of PVA at the oil/water interface decreased with the increase of the degree of hydrolysis (DH) of PVA in the DH range of 70–98 mol %, while the interfacial tension of VC/PVA aqueous solution increased linearly with the increase of DH of PVA. PVC resin with more regular particle shape, increased agglomeration and fusion of primary particles, lower porosity and higher bulk density, was prepared by using PVA with a higher DH as a suspending agent. This was caused by the occurrence of drop coalescence at the very early stage of VC polymerization, the increase of particle shrinkage, and the lower colloidal protection to primary particles. It was also shown that the interfacial tension of VC/water in the presence of composed PVA suspending agents varied linearly with the weight composition of the composed PVA suspending agents. The particle properties of PVC resin prepared by using the composed PVC suspending agents were usually situated in between the properties of PVC resins prepared by using the corresponding individual PVA suspending agent. The particle morphology and properties of PVC resin could be controlled by the suitable choice of the composed PVA suspending agents. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3848–3855, 2003