Enhancement of Interlaminar Fracture Toughness of Carbon Fiber/Epoxy Composites Using Silk Fibroin Electrospun Nanofibers

In this article, the effect of silk fibroin nanofibers as a toughening agent of carbon fiber/fabric-reinforced epoxy composites is experimentally investigated. The composites showed up to 30% improvement in Mode II fracture toughness at 0.1 wt% of silk fibroin nanofibers content. The scanning electron microscopy observation revealed that the fracture surface of silk fibroin nanofibers modified carbon fiber/fabric-reinforced epoxy composites appearance of the broken fiber and the ductile-like matrix cracks showed a good adhesion between matrix resin and carbon fibers, which are reasons for the enhanced mode II interlaminar fracture toughness.     

Simultaneous enhancement of electrical conductivity and interlaminar shear strength of CF/EP composites through MWCNTs doped thermoplastic polyurethane film interleaves

Carbon fiber-reinforced epoxy (CF/EP) composites have been widely used in aerospace industry, while poor electrical conductivity and interlaminar shear fracture toughness could reduce their safety as structural components in use. In this work, we achieved simultaneous improvement in electrical conductivity and interlaminar shear strength through interleaved multi-walled carbon nanotubes (MWCNTs) doped thermoplastic polyurethane (TPU) conductive thin films (CTFs), which were prepared by a solution casting method. The experimental results showed that the electrical conductivity of the laminates increased by about 13 and 16 times in the transverse and thickness directions with only about 1 wt % MWCNTs content in the laminates. The end-notch flexure (ENF) tests showed that the mode II interlaminar fracture toughness (G_IIC) of composites with 10 wt % MWCNTs CTF interleaf shows a significant increase of about 106%. The enhancement mechanism was further explored through microscopic morphological observation. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47988.     

Mechanically robust,electrically and thermally conductive graphene-based epoxy adhesives

This study develops a facile approach to fabricate adhesives consists of epoxy and cost-effective graphene platelets (GnPs). Morphology, mechanical properties, electrical and thermal conductivity, and adhesive toughness of epoxy/GnP nanocomposite were investigated. Significant improvements in mechanical properties of epoxy/GnP nanocomposites were achieved at low GnP loading of merely 0.5?vol%; for example, Young’s modulus, fracture toughness (K_1C) and energy release rate (G_1C) increased by 71%, 133% and 190%, respectively compared to neat epoxy. Percolation threshold of electrical conductivity is recorded at 0.58?vol% and thermal conductivity of 2.13?W m^?1 K^?1 at 6?vol% showing 4 folds enhancements. The lap shear strength of epoxy/GnP nanocomposite adhesive improved from 10.7?MPa for neat epoxy to 13.57?MPa at 0.375?vol% GnPs. The concluded results are superior to other composites or adhesives at similar fractions of fillers such as single-walled carbon nanotubes, multi-walled carbon nanotubes or graphene oxide. The study promises that GnPs are ideal candidate to achieve multifunctional epoxy adhesives.     

Delamination toughness of fiber-reinforced composites containing a carbon nanotube/polyamide-12 epoxy thin film interlayer

We present a simple, out-of-autoclave approach to improve the delamination toughness of fiber-reinforced composites using epoxy interlayers containing 20 wt.% polyamide-12 (PA) particles and 1 wt.% multi-walled carbon nanotubes (MWCNTs). Composites were prepared by integrating partially cured thin films at the laminate mid-plane using vacuum-assisted resin transfer molding. The introduction of epoxy/PA interlayers increased fracture toughness due to the ductile deformation and crack bridging of PA particles within an interlaminar damage zone with uniform thickness of about 20 μm. Composites interlayered with epoxy/PA/MWCNT exhibited nearly 2.5 and 1.5 times higher fracture toughness than composites containing neat epoxy and epoxy/PA interlayers, respectively, without an observable increase in interlaminar thickness. The fracture surface was analyzed to identify failure modes responsible for the fracture toughness improvement. The MWCNTs are proposed to inhibit critical loading of defects by minimizing stress concentration within the interlaminar region, thereby enabling greater deformation of the PA particles during fracture.     

Mode I interlaminar fracture toughness of Nylon 66 nanofibrilmat interleaved carbon/epoxy laminates

Carbon/epoxy laminates interleaved with laboratory scale electrospun Nylon 66 nanofibrilmat and spunbonded nonwoven mats were investigated. The effect of the nanoscale fibers on the fracture toughness of the composite under pure Mode I loading was evaluated. It was shown that the nanofibrilmat is responsible for a major interlaminar fracture toughness improvement, as high as 255–322%, compared to a noninterleaved carbon/epoxy reference laminate. We further studied the improvement mechanism of the electrospun nanofibrilmat compared to a commercial spunbonded nonwoven Nylon 66 mat. A combination of two interlayer fracture mechanisms responsible for the toughness improvement is suggested: the first is related to the high energy dissipated by bridged thermoplastic nanofibers and the second is attributed to the generation of a plastic zone near the crack tip. The interlaminar fracture mechanisms of both electrospun nanofibrilmat and the nonwoven mat interleaving was analyzed and discussed. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers     

Effects of carbon nanofiller functionalization and distribution on interlaminar fracture toughness of multi-scale reinforced polymer composites

Carbon nanofillers with different surface functional groups and aspect ratios, including carboxyl carbon nanotubes, un-functionalized carbon nanofibers (CNFs), glycidyloxypropyl-trimethoxysilane carbon nanotubes (GPS-CNTs) and nanofibers were evaluated for their potential for increasing the interlaminar fracture toughness of an S2-glass fiber/epoxy composite. The fillers were added in the matrix of the fiber reinforced plies, in the resin interlayer between plies, or in both regions. Comparisons were made based on mode I and mode II interlaminar fracture toughness. For composites made with CNTs dispersed in the matrix, fracture toughness was largely unaffected except for a slight increase seen with long GPS-CNTs. However, adding a CNF or CNT modified resin interlayer significantly increased the fracture toughness, with the highest improvement over the baseline material achieved by adding long GPS-CNTs in the interlayer (79% and 91% for mode I and mode II onset toughness, respectively). Important material parameters identified for improving interlaminar fracture toughness are the nanofiller aspect ratio and concentration at the fracture plane. Based on microscopic evaluations of the fracture surfaces, a high density of high aspect ratio nanofillers causes the best entanglement between the filler and glass fibers and effectively obstructs interlaminar crack propagation.     

Toughness and roughness in hybrid nanocomposites of an epoxy matrix

The present paper investigates the relationship between roughness and toughening mechanisms in hybrid epoxy nanocomposites with carbon nanotubes (CNT) and graphene nanoplatelets (GNPs). The role of adding a block copolymer (BC) to the studied systems was also investigated. The nanocomposites were prepared by means of high‐energy sonication and in situ polymerization. All nanocomposites presented higher numerical values for K_Ic than untoughened systems. The system containing 0.5 wt% of CNTs presented an increase of 35% in K_Ic compared to neat epoxy, and the hybrid nanocomposite, at the proportion of 1:1 (CNT:GNP), with 0.5 wt% total of nanoparticles and also containing 0.5 wt% of BC, had an increase of 34% compared to the neat epoxy. Systems with higher amounts of graphene showed the highest roughness values, having crack deflection/exfoliation between the GNP layers as the main toughening mechanism. On the other hand, systems with more CNTs presented a lower fracture surface roughness, and the main toughening mechanism was bridging/break‐up of the nanotubes. Hybrid systems have more types of mechanisms than simple ones. With only one type of nanoparticle, however, some of those mechanisms are not effective in increasing the toughness, only increasing the fracture surface roughness. POLYM. ENG. SCI., 59:1258–1269 2019. © 2019 Society of Plastics Engineers     

Mode II interlaminar fracture behavior of carbon bead‐filled epoxy/glass fiber hybrid composite

To investigate the effect of including carbon beads on the mechanical properties of epoxy resin, the fracture toughness of carbon bead‐filled epoxy was earlier evaluated using a CT (compact tension) specimens and Mode I fracture toughness was observed. Based on those results, in this study, the Mode II interlaminar fracture toughness of carbon bead filled epoxy/glass fiber hybrid composites was evaluated using end notch flexure (ENF) specimens. The hybrid composites showed increased Mode II interlaminar fracture toughness. The optimal bead volume fraction was around 15%.     

Hydrothermal effects on the thermomechanical properties of high performance epoxy/clay nanocomposites

The effects of hydrothermal ageing on the thermomechanical properties of high performance epoxy and its nanocomposite were studied. The epoxy–clay nanocomposite was prepared through a recently developed “slurry‐compounding” approach. The cured samples were immersed in distilled water at 60°C for different periods of time before subjecting to characterization. The storage modulus, relaxation behavior, fracture toughness, and tensile properties were investigated. It was found that the storage modulus and α‐relaxation were strongly affected by water uptake, while the fracture toughness and Young's modulus were less influenced. Dependence of tensile strength and strain at break on water uptake was found to be different in neat epoxy and epoxy–clay systems. POLYM. ENG. SCI., 46:215–221, 2006. © 2005 Society of Plastics Engineers     

Effect of Halloysite Nanotube Incorporation in Epoxy Resin and Carbon Fiber Ethylene/Ammonia Plasma Treatment on Their Interfacial Property

Abstract

Effects of halloysite nanotube (HNT) loading of up to 2% in epoxy resin on its mechanical properties were characterized. The interfacial property of the resin with carbon fiber nanocomposite was also studied. Single fiber composite (SFC) technique was used to characterize the carbon fiber/epoxy resin interfacial shear stress. Carbon fibers were also coated with ammonia/ethylene plasma polymer to obtain a thin coating of the polymer with amine groups that could react with the epoxy and thus improve the interfacial property. The results indicated that the Young’s modulus of HNT containing nanocomposites increased slightly up to a loading of 0.25% after which it started to decrease. The tensile strength, however, steadily decreased with increasing of HNT loading although the fracture strain did not change significantly. This might be related to the nanotube shape, size and clustering. The interfacial shear strength (IFSS) was also increased slightly with HNT loading. The ethylene/ammonia plasma polymer coated fibers exhibited significantly higher IFSS by over 150%, independent of the HNT loading. The highest IFSS obtained was almost 79 MPa for plasma treated fibers. The results suggest that the carbon fiber/epoxy interface is not affected by the incorporation of up to 1.5% of HNT. Furthermore, the fiber surface modification through plasma polymerization is an effective method to improve and control the IFSS.     

Physical and mechanical properties of kenaf/flax hybrid composites

This research investigates the physical and mechanical properties of hybrid composites made of epoxy reinforced by kenaf and flax natural fibers to investigate the hybridization influences of the composites. Pure and hybrid composites were fabricated using bi-directional kenaf and flax fabrics at different stacking sequences utilizing the vacuum-assisted resin infusion method. The pure and hybrid composites' physical properties, such as density, fiber volume fraction (FVF), water absorption capacity, and dimensional stability, were measured. The tests of tensile, flexural, interlaminar shear and fracture toughness (Mode II) were examined to determine the mechanical properties. The results revealed that density remained unchanged for the hybrid compared to pure kenaf/epoxy composites. The tensile, flexural, and interlaminar shear performance of flax/epoxy composite is improved by an increment of kenaf FVF in hybrid composites. The stacking sequence significantly affected the mechanical properties of hybrid composites. The highest tensile strength (59.8 MPa) was obtained for FK2 (alternative sequence of flax and kenaf fibers). However, FK3 (flax fiber located on the outer surfaces) had the highest interlaminar shear strength (12.5 MPa) and fracture toughness (3302.3 J/m²) among all tested hybrid composites. The highest water resistance was achieved for FK5 with the lowest thickness swelling.     

Crack-arrest study in mode II Delamination in composites

Procedures for measuring the crack initiation and arrest toughnesses in Mode II interlaminar fracture in composite materials were analyzed. Different techniques using flexural specimens were studied. The strain energy release rate, G, which is the energy available for crack propagation was calculated using simple beam theory. The calculation takes into account the transverse shear effect. Stable and unstable fractures are analyzed, and conditions required to measure the arrest toughness of interlaminar fracture are discussed. The methodology was applied to the measurement of fracture energy at the onset and arrest of delamination in glass/epoxy laminate.     

Influence of multiwalled carbon nanotubes on the processing behavior of epoxy powder compositions and on the mechanical properties of their fiber reinforced composites

This study reports the preparation of advanced carbon fiber composites with a nanocomposite matrix prepared by dispersing multiwall carbon nanotubes (CNTs) in a powder type epoxy oligomer with two different processing techniques (1) master batch dilution technique and (2) direct mixing (with the help of twin‐screw extruder in both cases). The master batch technique shows a better efficiency for the dispersion of the CNTs aggregates. The rheological results demonstrate that the incorporation of the CNTs into the epoxy oligomer leads, as expected, to a marked increase in the viscosity and of the presence of a yield stress point that also depends on the processing technique adopted. Carbon fiber (CFRP) and glass fiber (GFRP) composite materials were produced by electrostatic spraying of the epoxy matrix formulations on the carbon and glass fabric, respectively, followed by calendering and mold pressing. The mechanical properties of the obtained epoxy/CNT‐matrix composite materials, such as interlaminar fracture toughness, flexural strength, shear storage and loss moduli are discussed in terms of the processing techniques and fabric material. The incorporation of 1 wt% CNTs in the epoxy matrix results in a relevant increase of the fracture toughness, flexural strength and modulus of both CFRP and GFRP. POLYM. COMPOS., 37:2377–2383, 2016. © 2015 Society of Plastics Engineers     

The effect of silica nanoparticles and carbon nanotubes on the toughness of a thermosetting epoxy polymer

Silica nanoparticles and multiwalled carbon nanotubes (MWCNTs) have been incorporated into an anhydride‐cured epoxy resin to form “hybrid” nanocomposites. A good dispersion of the silica nanoparticles was found to occur, even at relatively high concentrations of the nanoparticles. However, in contrast, the MWCNTs were not so well dispersed but relatively agglomerated. The glass transition temperature of the epoxy polymer was 145°C and was not significantly affected by the addition of the silica nanoparticles or the MWCNTs. The Young's modulus was increased by the addition of the silica nanoparticles, but the addition of up to 0.18 wt % MWCNTs had no further significant effect. The addition of both MWCNTs and silica nanoparticles led to a significant improvement in the fracture toughness of these polymeric nanocomposites. For example, the fracture toughness was increased from 0.69 MPam^1/2 for the unmodified epoxy polymer to 1.03 MPam^1/2 for the hybrid nanocomposite containing both 0.18 wt % MWCNTs and 6.0 wt % silica nanoparticles; the fracture energy was also increased from 133 to 204 J/m². The mechanisms responsible for the enhancements in the measured toughness were identified by observing the fracture surfaces using field‐emission gun scanning electron microscopy. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effect of graphene oxide on the interlaminar fracture toughness of carbon fiber/epoxy composites

Graphene oxide (GO) nanoparticles were introduced in the interlaminar region of carbon fiber–epoxy composites by dispersing it in a thermoplastic polymer carrier such as polyvinylpyrrolidone (PVP). Mode‐I fracture toughness (G_IC) was investigated using double cantilever beam testing to evaluate the effect of the GO on the delamination behavior of the composite. The GO content was varied from 0% to 7% by weight as a function of the PVP content. Improvement of ～100% in the Mode I fracture toughness (G_IC) was observed compared to composites with no GO. The optimum amount of nanoparticles for improving the interlaminar fracture toughness was found to be ～0.007% by weight of the composite. The increase in the value of flexural strength value was also observed. Scanning electron microscopy of fracture surfaces, X‐ray diffraction, and transmission electron microscopy, and reflectance Fourier transform infrared spectra, as well as Raman spectroscopy results, are presented to support the conclusions. POLYM. ENG. SCI., 59:1199–1208 2019. © 2019 Society of Plastics Engineers     

The effects of surface-modified graphene nanoplatelets on the sliding wear properties of basalt fibers-reinforced epoxy composites

Possessing unique designs and properties absent in conventional materials, nanocomposites have made a remarkable imprint in science and technology. This is particularly true regarding the polymer matrix composites when they are further reinforced with nanoparticles. In this study, the effects of different weight percentages (0, 0.1, 0.2, 0.3, 0.4, and 0.5) of surface-modified graphene nanoplatelets (GNPs) on the microhardness and wear properties of basalt fibers/epoxy composites were investigated. The GNPs were surface modified by silane, and the composites were made by the hand lay-up method. The wear tests were conducted under two different loads of 20 and 40 N. The best wear properties were achieved at 0.3 wt % GNPs as a result of the GNPs' self-lubrication property and the formation of a stable transfer/lubricating film at the pin and disk interface. Moreover, the friction coefficient was lower at the higher normal load of 40 N. The microscopic studies by FESEM and SEM showed that the presence of GNPs up to 0.3 wt % led to the stability of the transfer/lubricating film by enhancing the adhesion of the basalt fibers to the epoxy resin. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47986.     

Microstructural,mechanical, and thermal characteristics of recycled cellulose fiber‐halloysite‐epoxy hybrid nanocomposites

Epoxy hybrid‐nanocomposites reinforced with recycled cellulose fibers (RCF) and halloysite nanotubes (HNTs) have been fabricated and investigated. The dispersion of HNTs was studied by synchrotron radiation diffraction (SRD) and transmission electron microscopy (TEM). The influences of RCF/HNTs dispersion on the mechanical properties and thermal properties of these composites have been characterized in terms of flexural strength, flexural modulus, fracture toughness, impact toughness, impact strength, and thermogravimetric analysis. The fracture surface morphology and toughness mechanisms were investigated by SEM. Results indicated that mechanical properties increased because of the addition of HNTs into the epoxy matrix. Flexural strength, flexural modulus, fracture toughness, and impact toughness increased by 20.8, 72.8, 56.5, and 25.0%, respectively, at 1 wt% HNTs load. The presence of RCF dramatically enhanced flexural strength, fracture toughness, impact strength, and impact toughness of the composites by 160%, 350%, 444%, and 263%, respectively. However, adding HNTs to RCF/epoxy showed only slight enhancements in flexural strength and fracture toughness. The inclusion of 5 wt% HNTs into RCF/epoxy ecocomposites increased the impact toughness by 27.6%. The presence of either HNTs or RCF accelerated the thermal degradation of neat epoxy. However, at high temperature, samples reinforced with RCF and HNTs displayed better thermal stability with increased char residue than neat resin. POLYM. COMPOS. 2012. © 2012 Society of Plastics Engineers     

Imidazole and chromium acetylacetonate as additives for the cure and fracture toughness of epoxy resins and their composites

The effects of additives such as 2-undecyl-imidazole (C₁₁Z) and chromium acetylacetonate (Cr(acac)₃) were examined on the curing behavior and fracture toughness of tetraglycidyldiaminodiphenyl methane/diaminodiphenyl sulphone (TGDDM/DDS) epoxy resins and their composites. The C₁₁Z additive alone reacted with TGDDM epoxy resins at about 127°C and increased the resin viscosity, resulting in an acceptable resin content for composite processing. Further addition of Cr(acac)₃ to TGDDM/DDS/C₁₁Z formulation increased the fracture toughness 5.7 times compared to the typical TGDDM/DDS/BF₃MEA epoxy formulation used for the preparation of laminates. The interlaminar fracture toughness of the laminates prepared by TGDDM/DDS/C₁₁Z/Cr(acac)₃ formulation was only twice as much as that prepared by typical TGDDM/DDS/BF₃MEA. This was due to the fiber bridging contribution to the interlaminar fracture toughness. Based on the experiment, this fiber bridging contribution was only dependent on the fiber content. Thus, the interlaminar fracture toughness is approximated by the sum of the fracture toughness of epoxy matrix and the estimated fiber bridging contribution.     

Mode I and Mode II delamination resistance and mechanical properties of woven glass/epoxy–PU IPN composites

The effect of polyurethane on the mechanical properties and Mode I and Mode II interlaminar fracture toughness of glass/epoxy composites were studied. Polyurethanes (PU) synthesized using polyols and toluene diisocyanate were employed as modifier for epoxy resin by forming interpenetrating polymer network. The PU/Epoxy IPN was used as matrix material for GFRP. PU modified epoxy composite laminates having varying PU contents were prepared. The effect of PU content on the mechanical properties like interlaminar fracture toughness (Mode I, G_1c and Mode II, G_IIc), tensile strength, flexural strength, and Izod impact strength were studied. The morphological studies were conducted on the fractured surface of the composite specimen by scanning electron microscopy (SEM). Tensile strength, flexural strength, and impact strength of PU‐modified epoxy composite laminates were found to increase inline with interlaminar fracture toughness (G_1c and G_IIc) with increasing PU content to a certain limit and then it was found to decrease with increase in PU content. It was observed that toughening of epoxy with PU increases the Mode I and Mode II delamination toughness up to 17 and 120% higher than that of untoughened composite specimen, respectively. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers     

Enhancement of flexural strength of glass fiber reinforced polymer laminates using multiwall carbon nanotubes

In this work, advance/multiscale nanocomposite were made by adding different amount (0, 0.5, 1.25, and 2 wt%) of multiwall carbon nanotubes (MWCNTs) to glass fiber reinforced polymer (GFRP) composites by hand lay‐up and vacuum bagging technique. Flexural strength and interlaminar shear strength (ILSS) of composites were performed on unfilled and MWCNTs‐filled glass fiber/epoxy nanocomposite to identify the effect of adding nanotubes on the mechanical properties. For understanding the structure and morphology of advance nanocomposite, the dispersion states were studied using field emission scanning electron microscopy (FE‐SEM). Mechanics of fracture behavior in different test were also discussed in details. POLYM. ENG. SCI., 59:E248–E261, 2019. © 2018 Society of Plastics Engineers