Physical and mechanical properties of kenaf/flax hybrid composites

This research investigates the physical and mechanical properties of hybrid composites made of epoxy reinforced by kenaf and flax natural fibers to investigate the hybridization influences of the composites. Pure and hybrid composites were fabricated using bi-directional kenaf and flax fabrics at different stacking sequences utilizing the vacuum-assisted resin infusion method. The pure and hybrid composites' physical properties, such as density, fiber volume fraction (FVF), water absorption capacity, and dimensional stability, were measured. The tests of tensile, flexural, interlaminar shear and fracture toughness (Mode II) were examined to determine the mechanical properties. The results revealed that density remained unchanged for the hybrid compared to pure kenaf/epoxy composites. The tensile, flexural, and interlaminar shear performance of flax/epoxy composite is improved by an increment of kenaf FVF in hybrid composites. The stacking sequence significantly affected the mechanical properties of hybrid composites. The highest tensile strength (59.8 MPa) was obtained for FK2 (alternative sequence of flax and kenaf fibers). However, FK3 (flax fiber located on the outer surfaces) had the highest interlaminar shear strength (12.5 MPa) and fracture toughness (3302.3 J/m²) among all tested hybrid composites. The highest water resistance was achieved for FK5 with the lowest thickness swelling.     

Structural degradation and mechanical fracture of hybrid fabric reinforced composites

This investigation involves the study of accelerated environmental aging in two polymer composite laminates reinforced by hybrid fabrics based on carbon, Kevlar and glass fibers. Composite laminate configurations are defined as a laminate reinforced with E‐glass fiber and Kevlar 49 fiber hybrid fabric (GK) and another laminate reinforced with E‐glass fiber and AS4 carbon fiber hybrid fabric (GC). Both laminates were impregnated with epoxy vinyl ester thermosetting resin (Derakane 470‐300) consisting of four layers. Morphological studies (photo‐oxidation process and structural degradation) of environmental aging were conducted, in addition to comparative studies of the mechanical properties and fracture characteristics under the action of uniaxial tensile and three‐point bending tests in specimens in the original and aged conditions. With respect to uniaxial tensile tests for both laminates, good mechanical performance and little final damage (small loss of properties) was caused by the aging effect. However, for the three‐point bending tests, for both laminates, the influence of aging was slightly higher for all parameters studied. The low structural deterioration in the laminates is attributed to the high performance with the heat of the matrix (Derakane 470‐300) and the characteristics of the hybrid fabric, exhibiting fiber/matrix interface quality. POLYM. ENG. SCI., 56:657–668, 2016. © 2016 Society of Plastics Engineers     

Hybridization effects on tensile and bending behavior of aramid/basalt fiber reinforced epoxy composites

In this study, the mechanical properties of aramid/basalt hybrid composite laminates were determined, and the effects of hybridization on the mechanical properties were investigated. To examine the effect of hybridization, the mechanical properties of aramid/basalt hybrid composite laminates were compared with those of aramid/epoxy and basalt/epoxy non‐hybrid composite laminates. The mechanical properties, tensile and flexural, of composite laminates were determined by performing uniaxial tensile and three‐point bending tests. The results showed that the employment of basalt fibers for partial substitution of aramid fibers in the composite laminate could provide improvements in the tensile and flexural properties. Furthermore, the results of three‐point bending tests were found that the employment of basalt fibers on compressive side across the thickness of composite laminates were realized significant improvement for flexural properties in comparison to the employment of basalt fibers on tensile side. POLYM. COMPOS., 38:1144–1150, 2017. © 2015 Society of Plastics Engineers     

Use of eco‐friendly epoxy resins from renewable resources as potential substitutes of petrochemical epoxy resins for ambient cured composites with flax reinforcements

In the last years, some high renewable content epoxy resins, derived from vegetable oils, have been developed at industrial level and are now commercially available; these can compete with petroleum‐based resins as thermoset matrices for composite materials. Nevertheless, due to the relatively high cost in comparison to petroleum‐based resins, their use is still restricted to applications with relatively low volume consumption such as model making, tuning components, nautical parts, special effects, outdoor sculptures, etc. in which, the use of composite laminates with carbon, aramid and, mainly, glass fibers is generalized by using hand layup and vacuum assisted resin transfer molding (VARTM) techniques due to low manufacturing costs and easy implementation. In this work, we study the behavior of two high renewable content epoxy resins derived from vegetable oils as potential substitutes of petroleum‐based epoxies in composite laminates with flax reinforcements by using the VARTM technique. The curing behavior of the different epoxy resins is compared in terms of the gel point and exothermicity profile by differential scanning calorimetry (DSC). In addition, overall performance of flax‐epoxy composites is compared with standardized mechanical (tensile, flexural and impact) and thermal (Vicat softening temperature, heat deflection temperature, thermo‐mechanical analysis) tests. The curing DSC profiles of the two eco‐friendly epoxy resins are similar to a conventional epoxy resin. They can be easily handled and processed by conventional VARTM process thus leading to composite laminates with flax with balanced mechanical and thermal properties, similar or even higher to a multipurpose epoxy resin. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Mechanical properties of glass/flax hybrid composites based on a novel modified soybean oil matrix material

In the Affordable Composites from Renewable Resources (ACRES) program at the University of Delaware, soybean oil and other plant triglycerides have been made amenable to polymerization using a broad range of chemical routes. The resultant polymers range in properties from soft rubbers to hard thermosets for composite applications. In this paper we present an investigation of the mechanical properties of glass/flax hybrid composites based on these thermoset matrix materials. Composites with different glass/flax ratios and different fiber arrangements were made using a modified soybean oil matrix material. The fiber arrangement was varied to make symmetric and unsymmetric composites. The latter were tested in different modes in flexural tests and drop weight impact tests. The mechanical properties of the composites were found to depend upon the glass/flax ratio and the arrangement of fibers in the composite. On proper selection of the arrangement of fibers in the composite, the glass fibers and flax fibers were found to act synergistically resulting in an improved flexural and impact performance. POLYM. COMPOS., 26:407–416, 2005. © 2005 Society of Plastics Engineers     

Effect of thermal shock cycling on the quasi-static and dynamic flexural properties of flax fabric-epoxy matrix laminates

The aim of the present work is to investigate the influence of thermal shock cycling on the quasi-static and dynamic flexural properties of epoxy matrix composites reinforced with natural flax fibers fabric. Polymer composite laminates reinforced with four plies of natural flax fiber fabric have been manufactured. The samples have been exposed to different number of thermal shock cycles (0, 50, 100, 200, 300, 400), at a temperature range from −40 °C to +28 °C. Dynamic mechanical analysis (DMA) tests were performed on both pristine and thermally shocked specimens in order to determine their viscoelastic response. Due to the thermal shock cycling and after 100 thermal shock cycles, a maximum decrease in storage and loss modulus on the order of 50% was observed. After 100 thermal shock cycles, no further degradation of dynamic properties was observed. On the contrary, damping factor and glass transition temperature values showed a minor variation as number of thermal shock cycles increased. In addition, the time–temperature superposition principle (TTSP) was successfully applied, confirming the fact that the flax fiber fabric-epoxy laminate is a thermo-rheologically simple material. Likewise, quasi-static three-point bending tests were executed and a maximum decrease of 20% in flexural strength was observed after 400 thermal shock cycles. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48529.     

Hygrothermal degradation of the composite laminates from woven carbon/SC‐15 epoxy resin and woven glass/SC‐15 epoxy resin

The degradation mechanism for hygrothermal aging of woven carbon‐epoxy and woven glass‐epoxy composite laminates was investigated in the micro‐scale. Interlaminar shear and cross laminar flexural tests were performed on notched and unnotched specimens to know the mechanical performance of the composite laminates. The Interlaminar Shear Stress (ISS) for both the composites was also evaluated and correlated with the number of hygrothermal cycles. Four‐point bending and tensile or compression shear loading configurations were also used. The stress at the onset of delamination (Delamination Damage Tolerance, DDT) was identified from the load‐deflection curve of the flexural specimens and correlated with the number of hygrothermal cycles. It was found that both the ISS and DDT decrease with the exposure time. Dimensional stability was almost unchanged throughout the aging process, although there was a very little moisture absorption (∼1.3%) in glass‐epoxy and carbon‐epoxy composite laminates. SEM photomicrographs of the delaminated surface show that failure occurs suddenly in a macroscopically brittle mode by crack initiation and propagation method. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers.     

Concentration effect of γ‐glycidoxypropyltrimethoxysilane on the mechanical properties of glass fiber–epoxy composites

In this study, glass fibers were modified using γ‐glycidoxypropyltrimethoxysilane of different concentrations to improve the interfacial adhesion at interfaces between fibers and matrix. Effects of γ‐glycidoxypropyltrimethoxysilane on mechanical properties and fracture behavior of glass fiber/epoxy composites were investigated experimentally. Mechanical properties of the composites have been investigated by tensile tests, short beam tests, and flexural tests. The short‐beam method was used to measure the interlaminar shear strength (ILSS) of laminates. The tensile and flexural properties of composites were characterized by tensile and three‐point bending tests, respectively. The fracture surfaces of the composites were observed with a scanning electron microscope. On comparing the results obtained for the different concentrations of silane solution, it was found that the 0.5% GPS silane treatment provided the best mechanical properties. The ILSS value of heat‐cleaned glass fiber reinforced composite is enhanced by ∼59% as a result of the glass fiber treatment with 0.5% γ‐GPS. Also, an improvement of about 37% in tensile strength, about 78% in flexural strength of the composite with the 0.5% γ‐GPS treatment of glass fibers was observed. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers     

Effect of water aging on the mechanical properties of flax fiber/bio-based resin composites

Present work investigates the effect of hydrothermal aging of flax fiber-reinforced bio-based epoxy resin laminates on the mechanical and thermomechanical properties of the composites. Three different types of bio-based resins were used. Plates reinforced with eight layers plain weave flax fibers of 150 g/m², manufactured using Resin Transfer Molding (RTM), compression molding or autoclave technique depends on type of the resin. One dimensional Fickian behavior shows a good fitting to the experimental data derived from weight measurements. The water uptake at the equilibrium state in the case of 60 °C temperature was slightly greater than that at 40 °C. The mechanical properties after hydrothermal aging show a significant reduction and do not return to their initial values even after the drying process. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48787.     

Mechanical properties of natural fiber hybrid composites based on renewable thermoset resins derived from soybean oil,for use in technical applications

Natural fiber composites are known to have lower mechanical properties than glass or carbon fiber reinforced composites. The hybrid natural fiber composites prepared in this study have relatively good mechanical properties. Different combinations of woven and non‐woven flax fibers were used. The stacking sequence of the fibers was in different orientations, such as 0°, +45°, and 90°. The composites manufactured had good mechanical properties. A tensile strength of about 119 MPa and Young's modulus of about 14 GPa was achieved, with flexural strength and modulus of about 201 MPa and 24 GPa, respectively. For the purposes of comparison, composites were made with a combination of woven fabrics and glass fibers. One ply of a glass fiber mat was sandwiched in the mid‐plane and this increased the tensile strength considerably to 168 MPa. Dynamic mechanical analysis was performed in order to determine the storage and loss modulus and the glass transition temperature of the composites. Microstructural analysis was done with scanning electron microscopy. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Development and application of triglyceride-based polymers and composites

Triglyceride oils derived from plants have been used to synthesize several different monomers for use in structural applications. These monomers have been found to form polymers with a wide range of physical properties. They exhibit tensile moduli in the 1–2 GPa range and glass transition temperatures in the range 70–120 °C, depending on the particular monomer and the resin composition. Composite materials were manufactured utilizing these resins and produced a variety of durable and strong materials. At low glass fiber content (35 wt %), composites produced from acrylated epoxidized soybean oil by resin transfer molding displayed a tensile modulus of 5.2 GPa, a flexural modulus of 9 GPa, a tensile strength of 129 MPa, and flexural strength of 206 MPa. At higher fiber contents (50 wt %) composites produced from acrylated epoxidized soybean oil displayed tensile and compression moduli of 24.8 GPa each, and tensile and compressive strengths of 463.2 and 302.6 MPa, respectively. In addition to glass fibers, natural fibers such as flax and hemp were used. Hemp composites of 20% fiber content displayed a tensile strength of 35 MPa and a tensile modulus of 4.4 GPa. The flexural modulus was ∼2.6 GPa and the flexural strength was in the range 35.7–51.3 MPa, depending on the test conditions. The flax composite materials had tensile and flexural strengths in the ranges 20–30 and 45–65 MPa, respectively. The properties exhibited by both the natural- and synthetic fiber-reinforced composites can be combined through the production of “hybrid” composites. These materials combine the low cost of natural fibers with the high performance of synthetic fibers. Their properties lie between those displayed by the all-glass and all-natural composites. Characterization of the polymer properties also presents opportunities for improvement through genetic engineering technology. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 703–723, 2001     

Manufacturing and mechanical behavior of hybrid building materials

This work is an experimental investigation of the flexural properties of hybrid matrix composites reinforced with different types of reinforcement, namely short glass fibers, glass beads, and short steel fibers. The aim of this investigation is to determine the mechanical behavior and properties of the composites that were manufactured, as well as to define an optimum composition of the materials used that will result in a composite with enhanced mechanical performance for building applications. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

A comparative analysis of woven jute/glass hybrid polymer composite with and without reinforcing of fly ash particles

The objective of this research article is to compare the mechanical and tribological properties of jute‐glass‐fiber‐reinforced epoxy (J‐G‐E) hybrid composites with and without fly ash particulate filler. A dry hand lay‐up technique is used to fabricate all the laminates. The properties including flexural strength, tensile strength, flexural modulus, and erosion behavior of all the composites are evaluated as per American Society for Testing and Materials (ASTM) standards. The fly ash particulate‐filled hybrid composite shows a better mechanical and tribological property. The maximum flexural strength and flexural modulus are obtained for GJGJ+ 5 wt% fly ash filler epoxy composites. Whereas the maximum tensile strength is obtained for GJJG+ 10 wt% fly ash filler epoxy composites. Scanning Electron Microscopy (SEM) analysis also has been carried out to categorize mechanical and tribological behavior of composites. POLYM. COMPOS. 37:658–665, 2016. © 2014 Society of Plastics Engineers     

Open hole flexural and izod impact strength of unidirectional flax yarn reinforced polypropylene composites as a function of laminate lay‐up

An open hole flexural strength and impact energy of flax yarn‐reinforced polypropylene (PP) composites were studied in this work. Highest flexural strength and strength retention were observed for axial (0₆) and cross‐ply (0/90/0)_s laminates, respectively, while also examining the influence of laminate lay‐up and open hole size on flexural strength. It was found that maleic anhydride‐grafted polypropylene (MAPP)‐treated composite laminates achieved marginal improvement on flexural strength for all kinds of laminate lay‐up. Off‐axial laminates (±45₆) showed a good strength retention for open hole laminates after MAPP treatment. The fractography study confirmed microbuckling and matrix crack propagation over the compressive and tensile side of the laminate, respectively. Furthermore, severe surface damage was detected over the tensile side of 8‐mm hole size laminates. Impact test of the flax/PP laminates showed slight improvement by MAPP treatment. High‐ and low‐impact energy was experienced for axial and off‐axial laminates. The damaged impact sample shows evidence of fiber pull‐out for untreated flax yarn reinforced laminates. POLYM. COMPOS., 34:1912–1920, 2013. © 2013 Society of Plastics Engineers     

Hybridization effect of cellulose paper and postcuring conditions on the mechanical properties of flax fiber reinforced epoxy biocomposite

An ever-increasing rise in demand for sustainable materials has received significant attention in developing biocomposites for structural applications. In this regard, natural fibers replacing synthetic fibers as reinforcement in epoxy composite could be a significant gain toward sustainability, especially in automobile and structural applications. Herein, flax fiber/cellulose paper–reinforced epoxy biocomposite (FREC-X) was fabricated via a vacuum infusion process. The influence of postcuring conditions (time and temperature) and cellulose paper density on the mechanical properties of FREC-X was studied. The tensile strength and modulus of FREC-X increased by 37% and 64%, respectively, upon the integration of paper. Postcuring FREC-X further augmented the tensile and flexural properties of the composite, which could be attributed to the increase in cross-linking of the epoxy and yields a strong polymer network. Fractography analysis confirmed that the composites integrated with paper showed fewer defects with improved interfacial adhesion. In addition, the water absorption and thickness swelling results revealed that the presence of cellulose paper marginally increased the water uptake and thickness swelling of FREC-X. Furthermore, there was no significant change in the tensile and flexural properties of FREC-X observed even after immersing in water for >200 h. Such properties of FREC-X seen as a fascinating alternative to synthetic fibers and petroleum-based epoxy and are promising material for sustainable development.     

Electrospinning core‐shell nanofibers for interfacial toughening and self‐healing of carbon‐fiber/epoxy composites

This article reports a novel hybrid multiscale carbon‐fiber/epoxy composite reinforced with self‐healing core‐shell nanofibers at interfaces. The ultrathin self‐healing fibers were fabricated by means of coelectrospinning, in which liquid dicyclopentadiene (DCPD) as the healing agent was enwrapped into polyacrylonitrile (PAN) to form core‐shell DCPD/PAN nanofibers. These core‐shell nanofibers were incorporated at interfaces of neighboring carbon‐fiber fabrics prior to resin infusion and formed into ultrathin self‐healing interlayers after resin infusion and curing. The core‐shell DCPD/PAN fibers are expected to function to self‐repair the interfacial damages in composite laminates, e.g., delamination. Wet layup, followed by vacuum‐assisted resin transfer molding (VARTM) technique, was used to process the proof‐of‐concept hybrid multiscale self‐healing composite. Three‐point bending test was utilized to evaluate the self‐healing effect of the core‐shell nanofibers on the flexural stiffness of the composite laminate after predamage failure. Experimental results indicate that the flexural stiffness of such novel self‐healing composite after predamage failure can be completely recovered by the self‐healing nanofiber interlayers. Scanning electron microscope (SEM) was utilized for fractographical analysis of the failed samples. SEM micrographs clearly evidenced the release of healing agent at laminate interfaces and the toughening and self‐healing mechanisms of the core‐shell nanofibers. This study expects a family of novel high‐strength, lightweight structural polymer composites with self‐healing function for potential use in aerospace and aeronautical structures, sports utilities, etc. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Modification of Glass Fiber-Reinforced Epoxy with Amine Functional Aniline Formaldehyde Condensate (AFAFC)

Unmodified epoxy glass fiber laminates are brittle by nature. In this study, an improvement of the mechanical properties, such as impact, tensile and flexural strengths of the reinforced glass fiber diglycidyl ether of bisphenol-A based epoxy laminate, was carried out by incorporating an amine functional aniline formaldehyde condensate (AFAFC) modifier. AFAFC was synthesized by reacting aniline and formaldehyde in an acid medium (pH 4) and was characterized by FT-IR and 1-H NMR spectroscopy, viscosity measurements, elemental analysis and potentiometric titration. The fracture energies of the modified glass fiber composite were vastly improved and the improvement depended on the concentration of the modifier. The optimum properties were obtained by adding 10 phr (parts per hundred parts of epoxy resin) of the modifier. Furthermore, the fracture energies of the modified glass fiber composite increased with increasing the number of glass fiber layers. Scanning electron microscopy showed that round shaped AFAFC oligomer domains were formed in the matrix. These oligomer domains led to improved strength and toughness due mainly to the 'rubber toughening' effect in the brittle epoxy matrix. The thermal stability of the modified epoxy composites by thermogravimetric analysis was also reported.     

Static and dynamic mechanical properties of a kenaf fiber–wood flour/polypropylene hybrid composite

A natural fiber hybrid composite containing equal proportions of kenaf fibers (KFs) and wood flour (WF) as the reinforcements and polypropylene (PP) as the polymer matrix was prepared, and its static and dynamic mechanical properties were compared with KF/PP and WF/PP composites. Static tensile and flexural tests and dynamic mechanical analysis (DMA) were carried out. The hybrid composite exhibited tensile and flexural moduli and strength values closer to those of the KF composite, which indicated a higher reinforcing efficiency of KFs compared with WF. DMA revealed that although the glass‐transition temperature remained unchanged by the replacement of half of the WF by KFs, the α‐transition temperature of the hybrid composite was identical to that of WF composite. The magnitudes of both the α and β (glass) transitions of the hybrid composite were comparable to that of the WF/PP composite. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 665–672, 2005     

Investigation of mechanical properties of alumina nanoparticle‐loaded hybrid glass/carbon‐fiber‐reinforced epoxy composites

This research work investigates the tensile strength and elastic modulus of the alumina nanoparticles, glass fiber, and carbon fiber reinforced epoxy composites. The first type composites were made by adding 1–5 wt % (in the interval of 1%) of alumina to the epoxy matrix, whereas the second and third categories of composites were made by adding 1–5 wt % short glass, carbon fibers to the matrix. A fourth type of composite has also been synthesized by incorporating both alumina particles (2 wt %) and fibers to the epoxy. Results showed that the longitudinal modulus has significantly improved because of the filler additions. Both tensile strength and modulus are further better for hybrid composites consisting both alumina particles and glass fibers or carbon fibers. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39749.     

连续玻纤增强聚丙烯混纤纱织物层压成型工艺研究

采用两种不同形式的混纤纱机织物为原料,利用层压成型的方法制备了连续玻璃纤维(GF)增强的聚丙烯(PP)板材。研究了层压温度、压力、保压时间和混纤纱机织物形式对层压板材的弯曲性能和层间剪切强度(ILSS)的影响。结果表明,当层压温度为230℃,层压压力为8.5 MPa,保压时间为30 min,降温过程冷却速度为0.5℃/min时,层压板材的力学性能最佳。弯曲强度和模量分别达到352.58 MPa、23.09 GPa,ILSS达到27.37 MPa。此时,纤维含量和空隙率分别为72.25%、2.03%。在最优工艺条件下制备的两种不同织物形式层压板材弯曲强度和弯曲模量以及ILSS:2/2斜纹织物平纹织物。两种织物层压板材的空隙率:2/2斜纹织物平纹织物。