Rheological behavior of collagen/chitosan blended solutions

Understanding the rheological behavior of collagen/chitosan blends is fundamental to design the optimized collagen/chitosan composite materials. Steady shear, dynamic frequency sweep, thixotropy and creep-recovery tests were investigated to characterize the rheological behavior of collagen/chitosan blends as a function of chitosan content (0%–90% [wt/wt]). All the samples showed pseudoplasticity with shear-thinning behavior. With the increase of chitosan, the viscosity significantly decreased from 862.54 to 0.60 Pa s at 0.05 s⁻¹. The storage modulus and loss modulus also decreased while the dynamic denaturation temperature increased from 39.79 to 45.18°C. Besides, the thixotropy weakened and when the chitosan content reached 70%, the final recovery percentage was only 4.6%. The entanglements between collagen fibers observed by atomic force microscopy became weaker. Finally, the corresponding mathematical models were used to simulate the experimental data, and the obtained parameters might provide some useful theoretical guidance for the processing of the collagen/chitosan blended solutions.     

Rheology of low nematic transition temperature thermotropic liquid crystalline copolyester HBA/HQ/SA

The rheology of a liquid crystalline copolyester of hydroxybenzoic acid, hydroquinone, and sebacic acid (HBA/HQ/SA copolyester) was studied on both a rotational and a capillary rheometer. DSC studies show that the copolyester has a crystalmesophasic and a broad mesophasic-isotropic transition at 170°C and 220°C. Optical texture observations show the mesophase is characterized by line defect textures, which are characteristic of a nematic structure. At 220°C, both isotropic and nematic phases coexist with the latter being the major. As temperature reaches 250°C, a clear dominance of isotropic phase is observed. At this temperature, the nematic phase of irregular shapes randomly disperses within the isotropic matrix. Subsequent rheological studies were thus conducted in crystal/nematic biphase, single nematic phase, nematic/isotropic biphase, and the near single isotropic phase. Dynamic strain sweep measurements show that a linear viscoelastic region exists at all temperatures tested. The maximum strain amplitude for the linear viscoelastic region is found to be highly structure dependent; it is > 100% in the nematic phase, ∼20% in the biphases, and only about 5% in the isotropic phase. The concurrence of curves obtained at different temperatures in a Cole-Cole plot of G′ vs. G″ indicates similar structures in the nematic phase and biphases. Measurements of steady shear viscosity using a rotational rheometer and a roundhole capillary rheometer show that in the nematic phase the copolyester behaves as a shear thinning fluid for a wide shear rate range of 1 ∼ 10,000 s⁻¹, in which the power law index is about 0.6 ∼ 0.8, and the viscosity is < 10 Pa.s at shear rates >1 s⁻¹.     

Solubility parameter estimation and phase inversion modeling of bentonite-doped polymeric membrane systems

Effects of bentonite concentration on morphology and permeation characteristics of bentonite-doped polysulfone membranes were investigated. Solubility sphere for bentonite was constructed to estimate its solubility parameter. Thermodynamic modeling of phase inversion of this system was carried out using Flory–Huggins theory. The trade-off between thermodynamic and kinetic parameters was used to predict the membrane morphology for bentonite concentration varying from 0 to 5 wt %. The porosity of bentonite-doped membranes decreased up to 3 wt % that increased thereafter. Morphological analysis showed dense cross section with finger-like macrovoids at 3 wt % beyond which it changed to honeycomb structure with large circular voids. Permeability of 3 wt % membrane was the lowest (5.6 × 10⁻¹² m/Pa s) with 95% bovine serum albumin rejection. Contact angle of the membranes decreased from 83 to 66° with bentonite addition making the membrane more hydrophilic. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48450.     

Characterization of the rheological behavior of UHMWPE gels using parallel plate rheometry

The effects of shear flow, temperature, and gel concentration on the rheological behavior of the ultrahigh-molecular-weight polyethylene (UHMWPE) gel in gel spinning process were investigated. The gel point was determined using parallel plate rheometry in rotation mode with controlled stress. Likewise, the flow curves at various temperatures were determined with controlled shear rate from 10⁻² to 10 s⁻¹. Whereas the shear storage modulus (G′) was obtained in oscillation mode with controlled strain from 1 to 100%. The result shows that the gel point of the UHMWPE gel increases with increasing gel concentration. The result from the strain sweep indicates that G′ of the gel is 1.5 × 10³ Pa, and it exhibits a plateau at low strain, but it is reduced with increasing strain. At low shear rates, for temperatures above gel point, all flow curves exhibit a plateau, then go down with increasing shear rate. Studying contributions from UHMWPE gel concentration, temperature, and shear rate for rheological view, we found that spinning at 6% UHMWPE (MW : 1.4 × 10⁶ g/mol) gel and 140°C gives the best effect on formation of fiber structure. © 1998 John Wiley & Sons, Inc. J. Appl. Polym. Sci. 70: 1009–1016, 1998     

Partially Sulfonated Poly(vinylidene fluoride) Induced Enhancements of Properties and DMFC Performance of Nafion Electrolyte Membrane

Partially sulfonated poly(vinylidene fluoride) (SPVdF) has been prepared by incorporation of sulfonic acid groups within poly(vinylidene fluoride), using chlorosulfonic acid as the sulfonating agent. The degree of sulfonation (DS) has been varied by modulating the duration of the sulfonation reaction. Blending of SPVdF (having DS = 36.78%) with Nafion at a constituent wt.% ratio of SPVdF:Nafion = 70:30 has resulted in the fabrication of polymer electrolyte membrane with superior properties compared to pristine Nafion‐117 membrane. This particular blend composition exhibited a proton conductivity value of 3.6 × 10⁻² S cm⁻¹ (i.e. ∼12.5% increase over Nafion‐117), a methanol permeability value of 6.81 × 10⁻⁷ cm² s⁻¹ at 6M methanol concentration (i.e. ∼99.31% decrease from Nafion‐117) and a corresponding membrane selectivity value of 5.29 × 10⁴ Ss cm⁻³ (i.e. an increase of approximately two‐orders of magnitude over Nafion‐117) at 20 °C. In addition, this blend composition has also exhibited (a) better heat stability at temperatures as high as 160 °C by virtue of it possessing higher glass transition temperature, (b) higher storage modulus, (c) higher stress relaxation at high angular frequency and (d) superior DMFC performance at high methanol feed concentration in presence of humidified, as well as, non‐humidified air as the catholyte, compared to Nafion‐117 membrane.     

Fabrication of hollow and porous polystyrene fibrous membranes by electrospinning combined with freeze-drying for oil removal from water

A novel method was proposed to fabricate hollow and surface porous polystyrene (PS) fibrous membranes for the removal of oil from water. Spinning solutions were prepared by using camphene and tetraethoxysilane (TEOS) as pore-forming agents, and hollow PS fibers with 100–400 nm pores on the surface were fabricated by electrospinning and freeze-drying. The distribution and volatilization of camphene and TEOS, as well as the drying behavior of solvents in high relative humidity, were important factors in forming the porous structure of PS fibers. The specific surface area of obtained PS fibrous membranes was twice that of conventional electrospun PS fibrous membranes and displayed superhydrophobic properties. Moreover, the large adsorption storage space was formed due to the hollow structure and porous surface of PS fibers. The maximum oil adsorption capacity of the porous PS fibrous membrane was 105.4 g g⁻¹, and was larger than that of the conventional PS fibrous membrane after repeated five times, thus making it a promising tool for oil spill cleanups. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47262.     

1,4-Bis(2,3-dicarboxyl-phenoxy)benzene dianhydride-based phenylethynyl terminated thermoset oligoimides for resin transfer molding applications

A series of thermoset oligoimides have been prepared by the thermal polycondensation of 1,4-bis(2,3-dicarboxyl-phenoxy)benzene dianhydride with three different aromatic diamines in the presence of 4-phenylethynylphthalic anhydride as an end capping reagent. The aromatic diamines included 4,4′-oxydianiline, 2,2′-bis(trifluoromethyl)benzidine (TFDB) and 2-phenyl-4,4′-diaminodiphenyl ether (p-ODA). Effects of the chemical structures and molecular weights of the oligoimides on their aggregated structures, melt processability as well as the thermal and mechanical properties of the cured films were then systematically investigated. X-ray diffraction results indicated that ODA series oligoimides and TFDB series oligoimides showed crystallinity; however, the asymmetrical p-ODA enables the p-ODA series oligoimides to exhibit amorphous forms. So the p-ODA based oligoimides with molecular weight of 750 g mol⁻¹ showed much lower melt viscosity at a low temperature and the melt viscosity could maintain below 1 Pa s⁻¹ after isothermal aging for 2 h at any temperature in the range of 220–280 °C by rheological measurements. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47967.     

Nanoenergetic Gas‐Generators: Design and Performance

Nanoenergetic gas‐generator (NGG) mixtures may have various potential military applications from aircraft fuels to rocket propellants, explosives, and primers. To find reactions generating the highest pressure peak, we studied eight nanoenergetic reactions. The Al/Bi₂O₃ reaction generated the highest pressure pulse among the eight thermite reactions. We developed a highly efficient, one step process for synthesis of Bi₂O₃ nanostructured particles. Its use generated about a three times higher peak pressure (∼10 MPa) than when using commercial bismuth oxide nanoparticles (3 MPa). The pressure in the vessel rose very rapidly to a peak value for a duration of ∼0.02 ms and ΔP/Δt of up to 500 GPa s⁻¹. Increasing the crystallinity of the bismuth oxide nanoparticles increased the peak gas pressure by 25%. The maximum pressure×volume (PV) value obtained at m=0.1 g with our synthesized Bi₂O₃ was 707 Pa m³ much higher than that reported in the literature (33 Pa m³) for the same sample mass. Addition of carbon to the reactant mixtures did not increase the peak pressure. Addition of up to 3 wt.‐% of boron to the thermite systems increased the peak pressure by ∼50%.     

Electrorheological behavior of low filled suspensions of highly anisometric montmorillonite particles

The electrorheological (ER) behavior of modified montmorillonite (MMT) suspensions in polydimethylsiloxane is studied. As established by rotational viscometry, the samples with a dispersed phase concentration from 1 to 8 wt % reveal viscous Newtonian behavior and dramatically change their properties to elastic when electric field is applied. The rheological characteristics of the suspensions over 0–7 kV mm⁻¹ range of electric field strengths are also studied. Novel X-ray diffraction method is developed to evaluate the suspension of the filler in a siloxane medium and to calculate the degree of its exfoliation. The dependence of exfoliation degree, dielectric, and ER characteristics on the type of modifier in the MMT structure is considered. Based on the obtained data, a new model of system behavior with the various types of fillers is proposed and the prospects of utilizing MMT as a filler for ER fluids are demonstrated. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47678.     

Inversion of sucrose solution by ion exchange: evaluation of reaction rate and diffusivity

The inversion of sucrose solution was studied in a packed bed of strongly acidic cation exchange resins in order to determine the values of the reaction rate constant, effective diffusivity and distribution coefficients for 20, 30 and 40 wt.% solution concentration. Typical values of specific rate constant for 30 wt.% sucrose solution varied from 0.0115 to 0.7391 min⁻¹ in the temperature range from 30 to 70 °C. The intrinsic values of activation energy and Arrhenius constant were 24.93 kcal mol⁻¹ and 7.657 × 10¹⁵ min⁻¹ respectively. The effective diffusivity varied from 3.826 × 10⁻⁸ to 18.951 × 10⁻⁸ cm² s⁻¹ for the above concentration and temperature intervals. The distribution coefficient was about unity. It was found that liquid film mass transfer resistance was important at low flow rates, although the solution concentration was high.     

Immobilization of carbonic anhydrase on polyethylenimine/dopamine codeposited membranes

Carbonic anhydrase (CA) catalyzing CO₂ hydration has an important application in carbon capture, and its immobilization is very significant. Here, CA was covalently linked by glutaraldehyde (GA) to the surface of poly(vinylidene fluoride) (PVDF) and polyethylene (PE) membranes, which were previously modified via a simple codeposition of polyethyleneimine (PEI) and dopamine (DA). The effects of the modification conditions were investigated, and the membranes were characterized by Fourier transform infrared spectroscopy and scanning electron microscopy. The immobilization process was optimized, and the catalytic properties of immobilized CA were studied. The results show that the optimal mass ratio of PEI and DA was 1:1 and the deposition time was 10–12 h, at which the surface amino group density could reach 1.278 × 10⁻⁷ and 1.397 × 10⁻⁷ mol/cm² for PVDF and PE, respectively. For enzyme immobilization, the optimal CA and GA concentrations were 0.2 mg/mL and 0.1 wt %, and a maximum activity recovery of about 53% and 76% could be achieved for PVDF-attached CA and PE-attached CA, respectively. Their K_m values were 10.62 mM and 8.6 mM, and the corresponding K_cat/K_m values were 132.2 M⁻¹ s⁻¹ and 312.9 M⁻¹ s⁻¹. After immobilization, the storage stability and reusability of CA were much improved. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47784.     

Humid aging of polyetherimide. I. Water sorption characteristics

The sorption and desorption kinetics of water into polyetherimide (ULTEM 1000) were studied at various temperatures ranging from 20 to 100°C. The water equilibrium concentration increases slightly with temperature from 1.39% (by weight) at 20°C to 1.50% at 100°C. The solubility coefficient, S, calculated from these data, and the water vapor pressure decrease with temperature. The calculated heat of dissolution H_s is close to −43 kJ mol⁻¹, which explains the low effect of temperature on the equilibrium concentration. The diffusion coefficient, D, varies from about 1.10⁻¹² m² · s⁻¹ at 20°C to about 16.10⁻¹² m² · s⁻¹ at 100°C. The apparent activation energy of diffusion, E_D, and the heat of dissolution, H_s, of water in the polymer have opposite values (respectively, +43 and −42 kJ · mol⁻¹). From this observation and a comparison of these data with water diffusion characteristics in other glassy polar polymers, it is hypothesized that the transport rate of water is kinetically controlled by the dissociation of water–polymer complexes. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 1439–1444, 2000     

Influence of different reactor types on Nannochloropsis oculata microalgae culture for lipids and fatty acid production

Greenhouse gases emitted into the atmosphere by burning of fossil fuels cause global warming. One option is obtaining biodiesel. Nannochloropsis oculata was cultured under different light intensities and reactors at 25°C for 21 days with f/2 medium to assess their effects on cell density, lipid, and fatty acids (FAs). N. oculata improved cell density on fed-batch glass tubular reactor (7 L) at 200 μmol E m⁻² s⁻¹, yielding 3.5 × 10⁸ cells ml⁻¹, followed by fed-batch Erlenmeyer flask (1 L) at 650 μmol E m⁻² s⁻¹ with 1.7 × 10⁸ cells ml⁻¹. The highest total lipid contents (% g lipid × g dry biomass⁻¹) were 44.4 ± 0.8% for the reactor (1 L) at 650 μmol E m⁻² s⁻¹ and 35.2 ± 0.2% for the tubular reactor (7 L) at 200 μmol E m⁻² s⁻¹, until twice as high compared with the control culture (Erlenmeyer flask 1 L, 80 μmol E m⁻² s⁻¹) with 21.2 ± 1%. Comparing the total lipid content at 200 μmol E m⁻² s⁻¹, tubular reactor (7 L) and reactor 1 L achieved 35.2 ± 0.2% and 28.3 ± 1%, respectively, indicating the effect of shape reactor. The FAs were affected by high light intensity, decreasing SFAs to 2.5%, and increased monounsaturated fatty acids + polyunsaturated fatty acids to 2.5%. PUFAs (20:5n-3) and (20:4n-3) were affected by reactor shape, decreasing by half in the tubular reactor. In the best culture, fed-batch tubular reactor (7 L) at 200 μmol E m⁻² s⁻¹ contains major FAs (16:0; 38.06 ± 0.16%), (16:1n-7; 30.74 ± 0.58%), and (18:1n-9; 17.15 ± 0.91%).     

Synthesis and properties of unsaturated polyoxyethylene and its graft copolymers with styrene

The unsaturated polyoxyethylene (PEO) was synthesized by copolymerization of ethylene oxide with allyl glycidyl ether in toluene using bimetallic-oxo-alkoxide as a catalyst. The effects of polymerization conditions on conversion and intrinsic viscosity of the copolymer were studied. The unsaturated copolymer was characterized with infrared spectra, ¹H NMR, and wide-angle X-ray diffraction. The relationship between crystallinity of the copolymers and conductivity of their LiClO₄ complexes were investigated. The copolymer with ∼ 65 wt % PEO content exhibits a room temperature conductivity of 1 × 10⁻⁴ S cm⁻¹ at a molar ratio of EO/Li = 20. The unsaturated PEO was graft-copolymerized with styrene using 2,2′-azobis(isobutyronitrile) as initiator in toluene, with grafting efficiency ∼ 50%. The purified graft copolymer was characterized with infrared spectra, ¹H NMR, and wide-angle X-ray diffraction, and was shown to have good emulsifying properties and a phase-transfer catalytic property. LiClO₄ complex of the graft copolymer with 70 wt % PEO content exhibits a room temperature conductivity approaching 1 × 10⁻⁴ S cm⁻¹ at molar ratio of EO/Li = 20/1. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 70: 2417–2425, 1998     

Fabrication and characterization of poly(vinylidene fluoride)–polytetrafluoroethylene composite membrane for CO2 absorption in gas–liquid contacting process

The wetting resistance of poly(vinylidene fluoride) (PVDF) membrane is a critical factor which determines the carbon dioxide (CO₂) absorption performance of the gas–liquid membrane contactors. In this study, the composite PVDF–polytetrafluoroethylene (PTFE) hollow fiber membranes were fabricated through dry-jet wet phase-inversion method by dispersing PTFE nanoparticles into PVDF solution and adopting phosphoric acid as nonsolvent additive. Compared with the PVDF membrane, the composite membranes presented higher CO₂ absorption flux due to their higher effective surface porosity and surface hydrophobicity. The composite membrane with addition of 5 wt % PTFE in the dope gained the optimum CO₂ absorption flux of 9.84 × 10⁻⁴ and 2.02 × 10⁻³ mol m⁻² s⁻¹ at an inlet gas (CO₂/N₂ = 19/81, v/v) flow rate of 100 mL min⁻¹ by using distilled water and aqueous diethanolamine solution, respectively. Moreover, the 5% PTFE membrane showed better long-term stability than the PVDF membrane regardless of different types of absorbent, indicating that polymer blending demonstrates great potential for gas separation. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47767.     

New composite membrane poly(vinyl alcohol)/graphene oxide for direct ethanol–proton exchange membrane fuel cell

This study investigated a simple synthesis of a crosslinked poly(vinyl alcohol)/ graphene oxide composite membrane with lower ethanol permeability membrane for passive direct ethanol–proton exchange membrane fuel cells (DE-PEMFCs). The chemical and physical structure, morphologies, ethanol uptake and permeability, ion exchange capacities, water uptake, and proton conductivities were determined and found that transport properties of the membrane were affected by the GO loading. The composite membrane with optimum GO content (15 wt %) exhibited the highest proton conductivity of 9.5 × 10⁻³ Scm⁻¹ at 30°C, 3.24 × 10⁻² Scm⁻¹ at 60°C, respectively and reduced ethanol permeability until 1.75 × 10⁻⁷ cm² s⁻¹. In the passive DE-PEMFC, the power density at 60°C were obtained as 5.84 mW cm⁻² higher than those by commercial Nafion 117 is 4.52 mW cm⁻². © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 46928.     

Assessment of compatibilization role of nanoclay in immiscible polystyrene/ethylene–octene copolymer blends via wide-angle X-ray scattering,microstructure, rheological analyses,and mechanical properties

Polystyrene (PS)/ethylene–octene copolymer (EOC) blends with 80/20 wt % composition containing different amounts (0, 1.0, 2.5, 5.0 and 7.5 wt %) of an organically modified nanoclay were prepared by one-step melt-mixing method. Also, the EOC-rich blends with 80 wt % EOC content loaded with 0 and 5.0 wt % of the nanoclay were prepared under the similar processing conditions. Presence of both PS and EOC chains in between clay layers localized at the interface of the blends could be deduced by X-ray diffraction analysis, which suggested formation possibility of PS-EOC physical structures at the blend interface. Transmission electron microscopy results confirmed that clay nanoparticles were mainly localized at the interface of the blends and also partly in the PS and EOC components of the systems. The localization of the nanoclay was also described by the linear viscoelastic melt rheological studies. It is also revealed that nanoclay had stronger interactions with PS than EOC. This is reflected in the higher tensile properties in the PS-rich system. The analysis of morphology of the developed systems by emulsification curve revealed that the optimum amount of nanoclay to modify PS-rich blend is 2.5 wt %. At this clay loading, the blend exhibited the highest impact resistance. According to the overall results, suitability of nanoclay was confirmed for compatibilization of the PS/EOC blends. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48748.     

High electromagnetic interference shielding with high electrical conductivity through selective dispersion of multiwall carbon nanotube in poly (ε‐caprolactone)/MWCNT composites

This study presents the preparation of electrically conducting poly(ε‐caprolactone) (PCL)/multiwall carbon nanotube (MWCNT) composites with very low percolation threshold (p_c). The method involves solution blending of PCL and MWCNT in the presence of commercial PCL beads. The PCL beads were added into high viscous PCL/MWCNT mixture during evaporation of solvent. Here, the used commercial PCL polymer beads act as an ‘excluded volume’ in the solution blended PCL/MWCNT region. Thus, the effective concentration of the MWCNT dramatically increases in the solution blended region and a strong interconnected continuous conductive network path of CNT−CNT is assumed throughout the matrix phase with the addition of PCL bead which plays a crucial role to improve the electromagnetic interference shielding effectiveness (EMI SE) and electrical conductivity at very low MWCNT loading. Thus, high EMI SE value (∼23.8 dB) was achieved at low MWCNT loading (1.8 wt %) in the presence of 70 wt % PCL bead and the high electrical conductivity of ∼2.49×10⁻² S cm⁻¹ was achieved at very low MWCNT loading (∼0.15 wt %) with 70 wt % PCL bead content in the composites. The electrical conductivity gradually increased with increasing the PCL bead concentration, as well as, MWCNT loading in the composites. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42161.     

Treatment of fishery washing water by ultrafiltration

The recovery and concentration of proteins from the waste water of a fish plant was achieved by ultrafiltration. Two UF modules equipped with Ceraver and Patterson Candy International (PCI) membranes were tested. Despite different cut-off values, similar apparent rejection coefficients (70% and 80% respectively) were obtained. Optimum economic conditions were established, corresponding to average transmembrane pressures of 2·2 × 10⁵ and 3·8 × 10⁵ Pa and tangential flow rates of 6·0 and 0·47 m s⁻¹ for Ceraver and PCI membranes, respectively. The protein concentration in the feed solution was increased from 5 to 35 g dm⁻³. The study showed that the method could reduce pollution due to organic matter by decreasing the value of the Biological Oxygen Demand after 5 days (BOD₅) by about 80%.     

Electrical conductivity of carbon black/single-wall carbon nanotube/low-density polyethylene ternary composite foam

In order to obtain high electrical conductive low-density polyethylene (LDPE) foam, carbon black (CB), single-wall carbon nanotube (SWCNT), and LDPE (CB/SWCNT/LDPE) ternary composite foams were successfully fabricated by chemical compression molding method. The electrical conductivity, mechanical properties, microstructure, density, and crystallinity of the foam were studied in detail. It can be found that CB and SWCNT have synergistic effect. For the CB/SWCNT/LDPE composite foam which containing 19 wt % CB and 0.05 wt % SWCNT, its density is only 0.082 g cm⁻¹ and the electrical conductivity can reach at 2.88 × 10⁻⁵ S cm⁻³, which is far more than 15 orders of magnitudes of pure polyethylene and 4 orders of magnitudes times higher than sample which CB content is 19 wt %. It is noteworthy that ultralow concentration of SWCNT could drastically improve the electrical conductivity and reduce the density of LDPE foams. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48382.