Effects of charge trapping on the electrical conductivity of low‐density Polyethylene–Carbon black composites

Electrical conductivities of low‐density polyethylene (LDPE)–carbon black (CB) composites were studied using high resistance meter at room temperature (DC conductivity) and dielectric spectroscopy (AC conductivity) in the frequency range between 90 kHz and 13 MHz and temperature range from 120 to 355 K. DC measurements revealed a percolation threshold at about 20 wt % of CB content, whereas AC measurements show two conductivity peaks at about 15% and 23% of CB content. The presence of two percolation thresholds was attributed to different dispersions of CB particles in structural inhomogeneities of LDPE. The experimental data were analyzed using the model of Efros and Shklovskii, which describes the critical behavior of a complex conductivity using critical indexes. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Reduced percolation concentration in polypropylene/expanded graphite composites: Effect of viscosity and polypyrrole

With the goal to obtain material combining electrical and thermal conductivity at low filler loadings, composites based on polypropylenes (PP) and expanded graphite (EG) have been prepared. The effects of matrix viscosity and of coating the EG particles with polypyrrole (PPy, EG/PPy = 37.5/62.5 by weight) on the EG dispersibility and formation of percolation structures have been analyzed. When increasing the EG amount from 6 to 8 wt %, the electrical conductivity of PP/EG composites increased by 7–9 orders of magnitude, independent of matrix viscosity. When EG‐PPy is added, percolation was observed between 8 and 12 wt % EG‐PPy (3 and 4.5 wt % EG) in case of PP with higher viscosity and 6 wt % EG (2.25 wt % EG) in case of PP with lower viscosity, exhibiting a strong synergistic effect of EG and PPy in the latter case. In contrast, PPy does not contribute to reduction of thermal percolation concentration. Thermal percolation is observed at 8 wt % EG in PP/EG composites, but no percolation was found in PP/EG‐PPy composites with EG‐PPy contents of up to 20 wt %, corresponding to 7.5 wt % EG. Analyzing the melt rheology it becomes clear that the contribution of PPy to the formation of a filler network is strongly dependent on the matrix viscosity. The comparison of thermal, electrical and rheological percolation reveals that PPy participates in electron transport reducing the electrical percolation but not to heat transport. Overall, we found a good correlation between electrical, thermal, and melt rheological percolation concentrations. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41994.     

填充型多相聚合物导电复合材料的PTC效应

以聚丙烯和低密度聚乙烯共混物为基体,用碳黑为填充材料制备了复合导电材料,导电性能的测试表明多相复合体系的渗滤阈值低于两相复合体系的渗滤阈值。对复合材料PTC效应的分析以及对材料的热性能测试结果表明碳黑在共混体系中的分布。同时探讨了体系碳黑含量的变化对PTC效应的影响。     

An electrical approach to monitor wire and cable thermal oxidation aging condition based on carbon black filled conductive polymer composite

Polymeric materials are widely used as insulation and jacketing materials in wire and cable. When such materials are used for long‐term applications, they undergo thermal oxidation aging in the environment. It is necessary to develop an in situ and nondestructive condition monitoring (CM) method to follow the aging of cable materials. The main objective of this work was to investigate low‐density polyethylene/carbon black (LDPE/CB) conductive polymer composites as potential sensor materials for this purpose. LDPE/CB composites with a carbon black loading below the percolation threshold underwent accelerated thermal oxidation aging experiments. The results indicated that the substantial resistivity decreases of the LDPE/CB composites could be directly related to the increases in volume fraction of the conductive carbon black, which was mainly caused by the mass loss of polymer matrix and sample shrinkage during the thermal oxidation aging process. Compared to existing CM method based on density change, the electrical resistivity is more explicit regarding its absolute changes throughout the thermal oxidation aging. The change in resistivity spanned over four orders of magnitude, whereas the composite density only increased 10%. The results offer strong evidence that resistivity measurements, which reflect property changes under thermal aging conditions, could represent a very useful and nondestructive CM approach as well as a more sensitive method than density CM approach. Crystallinity changes in materials investigated by modulated DSC and TGA measurements indicated deterioration of crystalline regions in polymer during the thermal oxidation aging. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 513–520, 2004     

Stability of electrical properties of carbon black‐filled rubbers

Conducting composites were prepared by melt mixing of ethylene–propylene–diene terpolymer (EPDM) or styrene‐butadiene rubber (SBR) and 35 wt % of carbon black (CB). Stability of electrical properties of rubber/CB composites during cyclic thermal treatment was examined and electrical conductivity was measured in situ. Significant increase of the conductivity was observed already after the first heating–cooling cycle to 85°C for both composites. The increase of conductivity of EPDM/35% CB and SBR/35% CB composites continued when cyclic heating‐cooling was extended to 105°C and 125°C. This effect can be explained by reorganization of conducting paths during the thermal treatment to the more conducting network. EPDM/35% CB and SBR/35% CB composites exhibited very good stability of electrical conductivity during storage at ambient conditions. The electrical conductivity of fresh prepared EPDM/35% CB composite was 1.7 × 10⁻² S cm⁻¹, and slightly lower conductivity value 1.1 × 10⁻² S cm⁻¹ was measured for SBR/35% CB. The values did not significantly change after three years storage. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Enhancement of electrical and thermal conductivity of polypropylene by graphene nanoplatelets

One of disadvantages of polymer composites is poor electrical and thermal conductivity. As a first step in this direction, graphene‐modified polypropylene polymer is being developed to improve its electrical and thermal conductivity. Two techniques were investigated: surface coating and extrusion. In the case of coating technique, the percolation threshold was found to be 0.5 wt % of graphene and electrical conductivity of polypropylene increased around 13 log cycles. Coating technique breaks the agglomerations due to magnetic stirring followed by sonication and gives homogeneous graphene‐coated polypropylene pellets. When polymer melts under compression molding, the graphene platelets network formed on the surface of polypropylene pellets as well as through‐the‐thickness of the molded disk, which provide continuous network of graphene. However, in extrusion technique, graphene segregated and did not disperse properly in polypropylene. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45833.     

Electrical and thermal conductivity and tensile and flexural properties: Comparison of carbon black/polycarbonate and carbon nanotube/polycarbonate resins

Adding conductive carbon fillers to thermoplastic polymers increases the resulting composite's electrical conductivity. Carbon black (CB) is very effective at increasing composite electrical conductivity at low loading levels. In this study, varying amounts (2 to 10 wt %) CB were added to polycarbonate (PC) and the resulting composites were tested for electrical conductivity (1/electrical resistivity), thermal conductivity, and tensile and flexural properties. These results were compared with prior work done for carbon nanotubes (CNT) in polycarbonate. The percolation threshold was ～ 2.3 vol % CB compared to between 0.7 and 1.4 vol % CNT. At 8 wt % filler, the CNT/PC composite had an electrical resistivity of 8 ohm‐cm compared to 122 ohm‐cm for the CB/PC composite. The addition of CB to polycarbonate increased the composite electrical and thermal conductivity and tensile and flexural modulus. The 8 wt % (5.5 vol %) CB in polycarbonate composite had a good combination of properties for semiconductive applications. Ductile tensile behavior is noted in pure polycarbonate and in samples containing up to 8 wt % CB. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effect of surfactant and electron treatment on the electrical and thermal conductivity as well as thermal and mechanical properties of ethylene vinyl acetate/expanded graphite composites

This study presents an investigation of the electrical and thermal conductivities of composites based on an ethylene vinyl acetate (EVA) copolymer matrix and nanostructured expanded graphite (EG). To improve the EG dispersion in EVA, EG sheets were modified by treating them with the anionic surfactant sodium dodecyl sulphate (SDS) in water. The modified SDS‐EG platelets, after being filtered and dried, were melt‐mixed with EVA to prepare the composites. Finally, both EVA/EG and EVA/SDS‐EG composites were subjected to 50 kGy electron beam (EB) irradiation. SEM images confirm that the irradiated EVA/EG samples had improved interfacial adhesion, while the irradiated EVA/SDS‐EG samples showed even better interfacial adhesion. The gel contents of the irradiated samples without and with SDS treatment increased with increase in EG loading. The EVA/EG composites exhibited a sharp transition from an insulator to a conductor at an electrical percolation threshold of 8 wt %, but with SDS‐EG the electrical conductivity was extremely low, showing no percolation up to 10 wt % of filler. The EB irradiation had no influence on electrical conductivity. The thermal conductivity linearly increased with EG content, and this increase was more pronounced in the case of SDS‐EG, but decreased after EB irradiation. The thermal properties were little influenced by EB irradiation, while better polymer–filler interaction and better filler dispersion as a result of SDS treatment, and the EB irradiation initiated formation of a cross‐linked network, had a positive effect on the tensile properties. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42396.     

Evaluation of the rheological and electrical percolation of high-density polyethylene/carbon black composites using mathematical models

In this work, conductive polymer composites (CPCs) of bio-based polyethylene (BioPe) containing different concentrations of carbon black (CB) were developed. By using oscillatory rheology analysis, a Newtonian plateau was observed in BioPe, and all BioPe/CB composites had a behavior of a pseudo-solid and that composites with volume fractions ranging from 0.24 to 0.56 presented higher viscosity, storage, and loss modulus. This suggests the formation of a percolated network and by using the power-law models, it was observed that the electrical percolation threshold was higher than the rheological percolation threshold. The electrical conductivity was measured using the four-point probe method and a sigmoid model was used to predict the CPCs' electrical conductivity percolation threshold. The results indicated that the four-point probe method presented satisfactory results according to the calculated standard deviations and voltage–current characteristics for each round of measurements considering the same ranging as used in rheology analysis. The analytical model used showed a coefficient of determination (R²) higher than 95%, allowing the prediction of the electrical conductivity of the CPC and the percolation threshold as a function of the volumetric fraction of the CB.     

Electrical conductivity of carbon black/single-wall carbon nanotube/low-density polyethylene ternary composite foam

In order to obtain high electrical conductive low-density polyethylene (LDPE) foam, carbon black (CB), single-wall carbon nanotube (SWCNT), and LDPE (CB/SWCNT/LDPE) ternary composite foams were successfully fabricated by chemical compression molding method. The electrical conductivity, mechanical properties, microstructure, density, and crystallinity of the foam were studied in detail. It can be found that CB and SWCNT have synergistic effect. For the CB/SWCNT/LDPE composite foam which containing 19 wt % CB and 0.05 wt % SWCNT, its density is only 0.082 g cm⁻¹ and the electrical conductivity can reach at 2.88 × 10⁻⁵ S cm⁻³, which is far more than 15 orders of magnitudes of pure polyethylene and 4 orders of magnitudes times higher than sample which CB content is 19 wt %. It is noteworthy that ultralow concentration of SWCNT could drastically improve the electrical conductivity and reduce the density of LDPE foams. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48382.     

Hybrid composites of ABS with carbonaceous fillers for electromagnetic shielding applications

This work evaluates the influence of two types of carbonaceous fillers, carbon black (CB) and carbon nanotubes (CNTs), on the electrical, electromagnetic, and rheological properties of composites based on poly(acrylonitrile‐co‐butadiene‐co‐styrene) (ABS) prepared by the melt mixing. Electrical conductivity, electromagnetic shielding efficiency (EMI SE) in the X‐band frequency range (8–12.4 GHz), and melt flow index (MFI) results showed that ABS/CNT composites exhibit higher electrical conductivity and EMI SE, but lower MFI when compared to ABS/CB composites. The electrical conductivity of the binary composites showed an increase of around 16 orders of magnitude, when compared to neat ABS, for both fillers. Binary composites with 5 and 15 wt % of filler showed an EMI SE of, respectively, ?44 and ?83 dB for ABS/CNT, and ?9 and ?34 dB for ABS/CB. MFI for binary composites with 5 wt % were 15.45 and 0.55 g/10 min for CB and CNT, respectively. Hybrid composites ABS/CNT.CB with 3 wt % total filler and fraction 50:50 and 75:25 showed good correlation between EMI SE and MFI. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46546.     

Study of carbon black‐filled poly(butylene succinate)/polylactide blend

In this study, carbon black (CB) was used to control the conductivity and the compatibility of immiscible poly(butylene succinate)/polylactide (PBS/PLA) blend. It is shown that most of the CB particles are selectively dispersed in the matrix PBS phase because of the viscosity ratio of the blend components. The increasing viscosity of PBS phase prevents the coalescence of the dispersed PLA domain during the melt mixing. The domain sizes of PLA are refined when compared with that of blank PBS/PLA blend. The ternary composite shows an onset of the electrical conductivity at low filler loadings (1.5 wt %), which is attributed to a percolation of CB in the insulating matrix polymer. Moreover, the composites exhibited remarkable improvement of rheological properties in the melt state when compared with that of blank PBS/PLA blend. According to the van Gurp‐Palmen plot, the rheological percolation threshold for ternary systems is lower than 1.5 wt %. Furthermore, the ternary composites present improved mechanical properties and thermal stability even at very low loading levels of the CB. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Graphene nanosheets‐filled epoxy composites prepared by a fast dispersion method

Graphene nanosheets‐filled epoxy composites (GNS/Epoxy) were prepared at different filler loading levels from 0.25 to 3.00 wt %. A fast dispersion method as short as 5 min is employed to disperse GNS in epoxy matrix, which was enough for the homogeneous dispersion of GNS with the help of high ultrasonic frequency of 100 kHz and power of 200 W and high heat treatment temperature of 70 °C. The maximum electrical conductivity and thermal conductivity of the composites achieved 0.058 S m^?1 and 0.57 W m^?1 K^?1, respectively, with a low electrical percolation threshold of 1.50 wt %. The electrical conductivities were further predicted by percolation theory and found to agree well with the experimental results, which indicated that the graphene nanosheets dispersed very well in the matrix even at very short processing time. The results showed that the microstructures, thermal, electrical, and mechanical properties of epoxy polymer were significantly improved by adding a low amount of graphene nanosheets. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 45152.     

Electromagnetic interference shielding of graphite/acrylonitrile butadiene styrene composites

Dispersion of graphite within the acrylonitrile butadiene styrene matrix demonstrates enhanced electromagnetic interference shielding of composites through the use of tumble mixing technique. A shielding effectiveness of 60 dB with 15 wt % of graphite has been achieved. D shore hardness data revealed a little decrease in hardness of composites with rise in graphite content. DC conductivity measurements revealed a fairly low percolation threshold at 3 wt % of graphite. The conductivity exhibited by 15 wt % composite is 1.66 × 10⁻¹ S/cm. These composites are fit for use as an effective and convenient EMI shielding material because of easy processing, better hardness, light weight, and, reasonable shielding efficiency. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effect of carbon black on electrical property of graphite nanoplatelets/epoxy resin composites

Epoxy/graphite nanoplatelets (GNPs)/carbon black (CB) composites were prepared by liquid mixing method. The morphologies and microstructures of the composites were examined by scanning electron microscope and X‐ray diffraction. The results indicated that CB can improve effectively the dispersion of GNPs and form excellent conductive network in the matrix. When the weight ratio of GNPs to CB was 9:1 (total filler content was 1 wt%), the conductivity of the composite was three orders of magnitude higher than that of composites with GNPs alone (1 wt%). The percolation threshold of GNPs_0.9CB_0.1/epoxy resin composites was 0.5 wt. %, which was lower than that of composites with GNPs alone (1 wt%). The mechanism for the effect of CB on electrical property of GNPs/epoxy resin composites was also investigated. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers.     

Electrical conductivity and percolation threshold of hybrid carbon/polymer composites

The electrical conductivity and percolation threshold of single and hybrid carbon filled composites are experimentally investigated. Polystyrene, carbon fiber (CF) and carbon black (CB) at three CF/CB ratios of 1.67, 3.33, 6.67 were compounded in a twin screw extruder micro‐compounder and compression molded into sheets. The through‐plane and in‐plane electrical conductivity of the composites are measured by 2 and 4 probe techniques. The percolation threshold of the single filler and hybrid composites are determined from the experimental results using a percolation model. The hybrid composites have a higher value of electrical conductivity and lower percolation threshold than the single CF filler composite except for the CF/CB ratio of 6.67. The percolation threshold for the cases of single filler and hybrid composites are modeled. The hard core / soft shell model is used and it is assumed that the percolation in a particle filled system depends on the ratio of tunneling distance to particle diameter. This ratio is determined by modeling single filler composites using the experimental data and kept constant in the modeling of the hybrid system. Finite size scaling is used to determine the percolation threshold for the infinite size hybrid system containing (nanosize) particles and micron size fibers for three CF/CB ratios. The simulation results show that the percolations of hybrid composites have the same trends observed in the experimental results. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41744.     

Polyurethane/conducting carbon black composites: Structure,electric conductivity,strain recovery behavior,and their relationships

The polyurethane composites with conducting carbon black (CB) were prepared by a solution‐precipitation process, which was followed by melt compression molding. The polyurethane used has good shape memory effect. The morphology of CB fillers in polyurethane matrix and the resulting conductivity of the composites were investigated. It has been found that CB fillers exist in the forms of aggregates. The percolation threshold is achieved at the CB concentration of 20 wt %. The presence of CB fillers decreases the degree of crystallinity of polycaprolactone (PCL) soft segments of the polyurethane. However, the composites still have enough soft‐segment crystals of polyurethane to fulfil the necessary condition for the shape memory properties. Dynamic mechanical data show that CB is an effective filler for the reinforcement of the polyurethane matrix, but does not deteriorate the stable physical cross‐link structure of the polyurethane, which is necessary to store the elastic energy in the service process of the shape memory materials. Addition of CB reinforcement in the polyurethane has influenced the strain recovery properties, especially for those samples with CB concentrations above the percolation threshold. The response temperature of the shape memory effect T_r has not been affected too much. Strain fixation S_f, which expresses the ability of the specimens to fix their strain, has been improved in the presence of the CB fillers. The final recovery rates R_f and strain recovery speeds V_r of the shape memory measurements, however, have decreased evidently. It is expectedly ascribed to the increased bulk viscosity as well as the impeding effect of the inter‐connective structure of CB fillers in the polymer matrix. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 68–77, 2000     

Electrical conductivity and rheological behavior of multiphase polymer composites containing conducting carbon black

Multiphase polymer composites of carbon black (CB), polypropylene (PP) and low density polyethylene (LDPE) were prepared by melt‐mixing method to reduce the amount of CB in the conductive composites. SEM images showed that CB preferably located in LDPE phase and formed electrically conductive path. The measurement of conductive properties showed that the ternary materials possessed lower percolation than binary composites of CB/PP or CB/LDPE, the former was ～6 wt% and the latter was 9–10 wt%. Positive temperature coefficient (PTC) effects of the binary and ternary composites were investigated, indicating that the latter exhibited a relatively high PTC intensity. A rheological percolation estimated by a power law function is 2.66 wt% of CB loading, suggesting an onset of solid‐like behavior at low frequencies. This difference between the electrical and rheological percolation thresholds may be understood in terms of the smaller CB–CB distance required for electrical conductivity as compared with that required to impede polymer mobility. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Electrical conductivity modeling of carbon black/polycarbonate,carbon nanotube/polycarbonate,and exfoliated graphite nanoplatelet/polycarbonate composites

Adding conductive carbon fillers to electrically insulating thermoplastic polymers increases the resulting composite's electrical conductivity, which would enable them to be used in electrostatic dissipative and semiconductive applications. In this study, varying amounts of carbon black (CB: 2 to 10 wt %), multiwalled carbon nanotubes (CNT: 0.5 to 8 wt %), or exfoliated graphite nanoplatelets (GNP: 2 to 15 wt %) were added to polycarbonate (PC) and the resulting composites were tested for electrical conductivity (EC = 1/electrical resistivity). The percolation threshold was ～ 1.2 vol % CNT, ～ 2.4 vol % CB, and ～ 4.6 vol % GNP. In addition, three EC models (Mamunya, additive, and general effective media) were developed for the CB/PC, CNT/PC, and GNP/PC composites. The general effective media (GEM) model showed the best agreement with the experimental results over the entire range of filler concentrations (above and below the percolation threshold) for all three composite systems. In addition, the GEM model can be easily adapted for composites containing combinations of different conductive fillers. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

In situ fast polymerization of graphene nanosheets‐filled poly(methyl methacrylate) nanocomposites

A series of graphene nanosheets‐filled poly(methyl methacrylate) nanocomposites (GNS/PMMA) is successfully prepared by an in situ fast polymerization method with graphene weight fractions from 0.1 to 2.0 wt %. In situ polymerization is effective in well dispersing of GNS in matrixes and suitable for both low and high content of GNS. The synthesis processes of polymer composites could be simplified and fast by using industrial grade graphene. The GNS fillers are found to disperse homogeneously in the PMMA matrix. The maximum electrical conductivity of the composites achieves 0.57 S m^?1, with an extremely low percolation threshold of 0.3 wt %. The electrical conductivities are further predicted by percolation theory and found to agree well with the experimental results. The results indicate that the microstructures, thermal, electrical, and mechanical properties of PMMA polymer are significantly improved by adding a low amount of graphene nanosheets. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43423.