Influence of ABS type on morphology and mechanical properties of PC/ABS blends

The morphology and the mechanical properties of polycarbonate (PC) blends with different acrylonitrile–butadiene–styrene (ABS) materials were investigated. PC/ABS blends based on a mass-made ABS with 16% rubber and large (0.5–1μm) rubber particles are compared to blends based on an emulsion-made ABS with 50% rubber and small, monodisperse (0.12 μm) rubber particles over the full range of blend compositions. The blends with the bulk ABS showed excellent impact strength for most compositions, and those containing 50 and 70% PC exhibited ductile to brittle transition temperatures below that of PC. The blends with the emulsion ABS showed excellent toughness in sharp notch Izod impact tests at room temperature and in standard notch Izod impact tests at low temperatures near the T_g of the rubber. By melt blending the various ABS materials with a styrene–acrylonitrile (SAN 25) copolymer, materials with lower rubber concentrations were obtained. These materials were used in blends with PC to make comparisons at constant rubber concentration of 5, 10, and 15%. The results of this investigation show that brittle ABS materials can produce tough PC–ABS blends. It is apparent that small rubber particles toughen PC–ABS blends at lower rubber concentrations and at lower temperatures than is possible with large rubber particles. However, additional work is needed to understand the nature of toughening in these PC–ABS blends with different rubber phase morphologies. It is of particular interest to understand the exceptional ductility of some of the blends at low temperatures. © 1994 John Wiley & Sons, Inc.     

Synthesis and characterization of ABS resin using in situ transferring from emulsion to suspension polymerization

A novel approach based on an emulsion in situ suspension polymerization process for synthesizing poly(acrylonitrile–butadiene–styrene) (ABS) resin is reported. Experimental results show that the reaction system can be transformed from an emulsion state to a suspension polymerization state steadily with the content of polybutadiene (PB) in the range 0–15 wt% in ABS resin. When PB is replaced by poly(styrene‐co‐butadiene) with the content of rubber particles being kept below 20 wt%, the emulsion system can be easily transferred to the suspension polymerization state through a process of latex coagulation in the forward direction, which means that the emulsion solution was dripped slowly into the suspension reaction system in the presence of coagulating agent. The dispersion status of the rubber particles in the ABS resin was studied using transmission electron microscopy, which indicated that the rubber particles were in a dispersed state in a continuous matrix of poly(styrene‐co‐acrylonitrile) when the content of rubber particles was below 20 wt%. The mechanical properties of the ABS resins obtained are as follows: elongation at break, 9.4–45.7%; yield tensile strength, 35.1–42.2 MPa; impact strength, 98.2–116.3 J m^?1. Copyright © 2006 Society of Chemical Industry     

Toughness of SMI‐modified ABS alloys and the associated deformation behavior

The mechanical toughness of modified ABS (acrylonitrile–butadiene–styrene) alloys was evaluated using Izod impact, tensile, and compact tension tests. The modified ABS alloys contain 20 wt % of styrene–N‐phenylmaleimide (SMI) that is added to enhance the thermal resistance of the ABS. In this study, the effects of matrix composition, rubber/matrix adhesion, and rubber particle structure on the alloy toughness were investigated. Results from the tensile test and Izod impact test ranked the alloys in an order that is different from that given by K_Ii (stress intensity factor for crack initiation), measured from compact tension specimens. This is due to the difference in energy‐absorption characteristics for crack initiation and crack growth. The conclusion is supported by optical micrographs on the deformation zone size. The microdeformation behavior of the alloys was examined using transmission electron microscopy (TEM), which revealed different rubber‐toughening mechanisms between Izod and tensile specimens. The former contains numerous extensive crazes, while the latter, only a very few short crazes, except in regions within a few micrometers from the fracture surface. The dominant matrix deformation mechanism for the tensile specimens is believed to be shear deformation. Another interesting observation from the study is rubber particle cavitation, commonly observed in tensile specimens and Izod specimens with solid rubber particles; it did not occur in the Izod specimens containing salami‐type rubber particles. This is attributed to the salami structure that increased the straining rate for the rubber phase, leading to ductile–brittle transition of the rubber. The transition to brittle deformation of the rubber phase prevented rubber particle cavitation. The microscopic examination indicated that toughening mechanisms by the rubber particles can be very different among the mechanical tests, which should be taken into account for the rubber toughening of polymers. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 1543–1553, 1999     

Effect of matrix SAN in ABS/PMMA blends

The effect of the molecular weight and acrylonitrile (AN) content of the styrene–acrylonitrile copolymer (SAN) on the morphology, mechanical properties, and rheological properties of acrylonitrile–butadiene–styrene terpolymer/poly(methyl methacrylate) (ABS)/PMMA (60/40 by weight) blends were studied. When the AN content of matrix SAN (32%) was close to that of graft SAN (30%) AN, rubber particles existed separately. However, with matrix SAN having 35% AN, rubber particles showed tendency to agglomerate each other. With increasing molecular weight of matrix SAN, impact strength, ultimate elongation, and abrasion resistance of the blend generally increased. Yield strength increased with molecular weight at a constant AN content of matrix SAN, and it decreased with the decrease of AN content in spite of the increasing molecular weight of SAN. Melt properties, rather than the morphological and mechanical properties, were more sensitive to the AN content, rather than the molecular weight of matrix SAN. © 1994 John Wiley & Sons, Inc.     

Mechanical properties and deformation behaviors of acrylonitrile‐butadiene‐styrene under Izod impact test and uniaxial tension at various strain rates

Two polybutadiene‐graft‐acrylonitrile‐styrene copolymer (PBD‐g‐SAN) impact modifiers with different rubber particle size were synthesized by seeded emulsion polymerization. Acrylonitrile‐butadiene‐styrene (ABS) blends with a constant rubber concentration of 15 wt% were prepared by blending those impact modifiers and SAN resin. The major focus was the mechanical properties and deformation mechanisms of ABS blends under Izod impact test and uniaxial tension at various strain rates from 2.564 × 10^?4 S^?1 upto 1.282 × 10^?1 S^?1. By the combination of transmission electron microscope and scanning electron microscope, it was concluded that crazes and cavitation coexisted in ABS blends. The deformation mechanisms of ABS blend containing large rubber particles was rubber particles cavitation and shear yielding in the matrix including crazes, and they do not change with the strain rate. Different from ABS blend with large rubber particles, deformation mechanism of ABS with small rubber particles under tensile condition was only involved in shear yielding in the matrix and no crazes were formed. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Influence of rubber content in ABS in wide range on the mechanical properties and morphology of PC/ABS blends with different composition

A series of acrylonitrile–butadiene–styrene (ABS) with different rubber content were prepared by diluting ABS grafting copolymer containing 60% rubber with a styrene–acrylonitrile copolymer. ABS prepared were blended with bisphenol‐A‐polycarbonate (PC) at the ratio of 70/30, 50/50, and 30/70 to prepare PC/ABS blends. Influence of rubber content in ABS on the properties of ABS and PC/ABS blends were investigated. PC/ABS blends with different compositions got good toughness when the rubber in ABS increased to the level that ABS itself got good toughness. The tensile properties and processability of PC/ABS blends decreased with the increase of the total rubber content introduced into the blends. ABS with the rubber content of 30 wt% is most suitable to be used to prepare PC/ABS blends. The rubber content in ABS affected the viscosity of ABS, and subsequently the viscosity ratio of PC to ABS. As a result, the morphology of PC/ABS blends varied. The increase of rubber content in ABS results in finer structure of PC/ABS blends. POLYM. ENG. SCI. 46:1476–1484, 2006. © 2006 Society of Plastics Engineers.     

Effects of the polybutadiene/poly(styrene‐co‐acrylonitrile) ratio in a polybutadiene‐g‐poly(styrene‐co‐acrylonitrile) impact modifier on the morphology and mechanical behavior of acrylonitrile–butadiene–styrene blends

Polybutadiene‐g‐poly(styrene‐co‐acrylonitrile) (PB‐g‐SAN) impact modifiers with different polybutadiene (PB)/poly(styrene‐co‐acrylonitrile) (SAN) ratios ranging from 20.5/79.5 to 82.7/17.3 were synthesized by seeded emulsion polymerization. Acrylonitrile–butadiene–styrene (ABS) blends with a constant rubber concentration of 15 wt % were prepared by the blending of these PB‐g‐SAN copolymers and SAN resin. The influence of the PB/SAN ratio in the PB‐g‐SAN impact modifier on the mechanical behavior and phase morphology of ABS blends was investigated. The mechanical tests showed that the impact strength and yield strength of the ABS blends had their maximum values as the PB/SAN ratio in the PB‐g‐SAN copolymer increased. A dynamic mechanical analysis of the ABS blends showed that the glass‐transition temperature of the rubbery phase shifted to a lower temperature, the maximum loss peak height of the rubbery phase increased and then decreased, and the storage modulus of the ABS blends increased with an increase in the PB/SAN ratio in the PB‐g‐SAN impact modifier. The morphological results of the ABS blends showed that the dispersion of rubber particle in the matrix and its internal structure were influenced by the PB/SAN ratio in the PB‐g‐SAN impact modifiers. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 2165–2171, 2005     

ABS/HIPS blends obtained from WEEE: Influence of processing conditions and composition

The recycling of acrylonitrile–butadiene–styrene (ABS) and high‐impact polystyrene (HIPS) from postconsumer electronic equipment housing was investigated. A preliminary study of shot size and particle size effects on the mechanical properties of ABS/HIPS (50/50) blends obtained directly via injection molding was conducted. Injection‐molded specimens of ABS/HIPS blends, obtained at different compositions with or without previous extrusion, were subjected to mechanical, thermal, and morphological testing. Preliminary studies showed that a smaller particle size resulted in higher tensile and impact strength, regardless of the shot size used during injection molding. ABS/HIPS blends obtained using previous extrusion presented a slight increase in Young's modulus and a decrease in elongation at break and impact strength. The increase in glass‐transition temperature related to the Polybutadiene (PB) phases of these blends indicated a possible increase in crosslinking structures during extrusion. In addition, these blends showed a coarse and heterogeneous morphology, suggesting that ABS did not completely mix with HIPS. Compared to processing conditions, the blend composition appeared to have a much stronger effect on the mechanical properties. The results obtained suggest the possibility of obtaining ABS/HIPS blends directly via injection molding as long as small ground particles are used. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43831.     

Effect of Rubber Content of ABS on Properties of PC/ABS Blends. I. Rheological,Mechanical, and Thermal Properties

ABSTRACT

The effect of rubber content of poly (acrylonitrile butadiene styrene) (ABS) on compatibility and properties of polycarbonate (PC)/ABS blend systems has been investigated. The rheological, mechanical, physical, and thermal properties of PC/ABS blend systems containing ABS of different rubber content were studied. The reduced torque data on Torque Rheocord indicated improved processability of PC by addition of ABS, however, in ABS-rich compositions, higher rubber content reduces the extent of improvement. The tensile strength of PC decreased with addition of ABS to it but PC-rich compositions have a nearly additive response. The deviation form additivity for blends having higher rubber ABS was more pronounced. However, the impact strength of blends having higher rubber ABS were higher than other types and showed a positive deviation from additivity with variation in compositions. The blends containing ABS with lower rubber content showed a single glass-transition temperature (Tg) in differential scanning calorimetry studies (DSC) in the whole composition range indicating miscibility. Although two Tgs, one associated with PC phase and one with ABS phase, were observed for blends containing high rubber ABS, the shift in Tgs with respect to pure component values indicates partial miscibility. The decrease in the extent of shift with increase of ABS in these blends indicates undesirable phase separation due to poor adhesion of higher level of rubber content.     

Toughening of poly(l‐lactide) modified by a small amount of acrylonitrile−butadiene−styrene core‐shell copolymer

A small amount of acrylonitrile‐butadiene‐styrene (ABS) core shell copolymer particles are used to improve the toughness of poly(l ‐lactide) (PLLA) matrix. The incorporation of ABS copolymer dramatically increased the elongation yield at break of PLLA. For PLLA blend with 6.0 wt % ABS copolymer particles, the elongation yield at break increased by 28 times and the notched impact strength improved by 100% comparing with those of neat PLLA. Fourier transformed infrared (FTIR) and dynamic mechanical analysis (DMA) and scanning electron microscopy (SEM) measurement results indicated that the special polarity interaction between ester group of PLLA matrix and nitrile group of PSAN shell phase enhanced the interfacial adhesion between PB rubber phase and PLLA matrix and promoted the fine dispersion of ABS particles in PLLA matrix. Meanwhile, ABS core shell particles also showed a certain extent of effects on the crystallinity behavior of PLLA. A small amount of ABS particles became the nucleating sites, and then the degree of crystallinity of PLLA/ABS blends increased. However, the notched impact of PLLA blends decreased because of the aggregation of more ABS particles. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42554.     

Morphological and mechanical properties of PP/ABS blends compatibilized with PP‐g‐acrylic acid

Polypropylene (PP) and acrylonitrile–butadiene–styrene (ABS) blends were prepared by a melt extrusion process. PP‐g‐acrylic acid was used as a compatibilizer. Blends with various compositions of PP, compatibilizer, and ABS were prepared and studied for morphological and mechanical properties. PP‐rich ternary blends showed good morphological and mechanical properties. The use of 5 wt % PP‐g‐acrylic acid as a compatibilizer resulted in a fine and homogeneous dispersion of the ABS phase in the PP phase. The experimental data of the tensile modulus showed good agreement in PP‐rich compositions with that generated from Kerner's model with perfect adhesion. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 1731–1741, 2001     

Influence of acrylonitrile–butadiene–styrene (ABS) morphology and poly(styrene‐co‐acrylonitrile) (SAN) content on fracture behavior of ABS/SAN blends

This study attempted to correlate morphological changes and physical properties for a high rubber content acrylonitrile–butadiene–styrene (ABS) and its diluted blends with a poly(styrene‐co‐acrylonitrile) (SAN) copolymer. The results showed a close relationship between rubber content and fracture toughness for the blends. The change of morphology in ABS/SAN blends explains in part some deviations in fracture behavior observed in ductile–brittle transition temperature shifts. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2606–2611, 2004     

Blends of bisphenol A polycarbonate and rubber‐toughened styrene–maleic anhydride copolymers

The morphology and mechanical properties of polycarbonate (PC) blends with rubber‐toughened styrene–maleic anhydride copolymer materials (TSMA) were investigated and compared with the properties of blends of PC with acrylonitrile–butadiene–styrene (ABS) materials. The PC/TSMA blends showed similar composition dependence of properties as the comparable PC/ABS blends. Polycarbonate blends with TSMA exhibited higher notched Izod impact toughness than pure PC under sharp‐notched conditions but the improvements are somewhat less than observed for similar blends with ABS. Since PC is known for its impact toughness except under sharp‐notched conditions, this represents a significant advantage of the rubber‐modified blends. PC blends with styrene–maleic anhydride copolymer (SMA) were compared to those with a styrene–acrylonitrile copolymer (SAN). The trends in blend morphology and mechanical properties were found to be qualitatively similar for the two types of copolymers. PC/SMA blends are nearly transparent or slightly pearlescent. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1508–1515, 1999     

Recycling of ABS and ABS/PC blends

The aim of this work within the framework of mechanical recycling of polymers is upgrading recycled engineering plastics by means of a blending technique. Four different plastics from dismantled Volvo cars have been investigated. They are poly(acrylonitrile‐butadiene‐styrene) (ABS) and ABS‐polycarbonate (ABS/PC) as major components and poly(methyl methacrylate) (PMMA) and polyamide (PA) as minor components. Blending recycled ABS and PC/ABS (70/30) with a small amount of methyl methacrylate‐butadiene‐styrene core‐shell impact modifiers gives the mixture better impact properties than any of its individual components. Some 10% of PMMA from tail light housings can follow the PC/ABS blends made. The property profile will rather be improved. However, PA is an incompatible component that should be sorted out from the mixture. Antioxidants and metal deactivators do not help the recyclates show better mechanical properties. Two toughness measurements, Charpy impact strength and J‐integral method, show complimentary results for such blends. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 510–515, 1999     

Influence of compatibilizer on mechanical,morphological and rheological properties of PP/ABS blends

The objective of this work was to study the compatibilizer effect on polypropylene (PP) and acrylonitrile butadiene styrene (ABS) blends. The blends were coextruded and injection molded in various ratios of ABS with and without compatibilizers. Universal testing machine was employed to analyze the tensile properties of basic PP/ABS binary blends. From the mechanical testing, the impact and tensile properties of PP/ABS blend were optimized at 80/20 weight ratio. Various compatibilizers such as PP-g-MAH, SEBS-g-MAH and ethylene α-olefin copolymer were used and their comparative performance on binary blend was enumerated. Hybrid compatibilization effect was also studied and reported. However, the addition of compatibilizers showed the maximum increase in impact strength attributed to rubber toughening effect of ABS. The effect of compatibilizers on morphological properties was examined using scanning electron microscopy (SEM). SEM micrographs depicted the more efficient dispersion of ABS particles in PP matrix with the addition of compatibilizers. Further, interparticle distance analysis was carried out to evaluate the rubber toughening effect. The ABS droplet size in compatibilized PP/ABS blend was brought to minimum of 3.2 μm from 9.9 μm with the addition of compatibilizers. The melt rheology of PP/ABS blend systems was investigated through parallel plate arrangement in frequency sweep. Linear viscoelastic properties like storage (G′) and loss (G″) modulus and complex viscosity (η*) have been reported with reference to the virgin materials. It is understood that the combination of compatibilizers (hybrid compatibilizer) had a considerable effect on the overall blend properties.     

Effect of styrene–isoprene–styrene,styrene–butadiene–styrene,and styrene–butadiene–rubber on the mechanical,thermal, rheological,and morphological properties of polypropylene/polystyrene blends

The mechanical, thermal, rheological, and morphological properties of polypropylene (PP)/polystyrene (PS) blends compatibilized with styrene–isoprene–styrene (SIS), styrene–butadiene–styrene (SBS), and styrene–butadiene–rubber (SBR) were studied. The incompatible PP and PS phases were effectively dispersed by the addition of SIS, SBS, and SBR as compatibilizers. The PP/PS blends were mechanically evaluated in terms of the impact strength, ductility, and tensile yield stress to determine the influence of the compatibilizers on the performance properties of these materials. SIS‐ and SBS‐compatibilized blends showed significantly improved impact strength and ductility in comparison with SBR‐compatibilized blends over the entire range of compatibilizer concentrations. Differential scanning calorimetry indicated compatibility between the components upon the addition of SIS, SBS, and SBR by the appearance of shifts in the melt peak of PP toward the melting range of PS. The melt viscosity and storage modulus of the blends depended on the composition, type, and amount of compatibilizer. Scanning electron microscopy images confirmed the compatibility between the PP and PS components in the presence of SIS, SBS, and SBR by showing finer phase domains. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 266–277, 2003     

PB橡胶粒径对CPVC/PVC/ABS共混体系结构与性能的影响

采用乳液聚合技术合成了一系列不同PB橡胶粒径的ABS核壳改性剂,将其与CPVC、PVC共混,考察了CPVC/PVC/ABS共混物的结构与性能。动态力学分析表明：CPVC与PVC比例为90/10时,CPVC/PVC共混物部分相容,CPVC/PVC/ABS共混物也是部分相容;扫描电子显微镜分析其形态结构表明：共混物中ABS分散受PB橡胶粒径影响,PB橡胶粒径为113 nm的ABS在CPVC中分散最均匀。力学性能测试表明：随着PB橡胶粒径的增加,共混物的冲击强度先增大后减小,拉伸强度并无明显变化。     

Synergistic effect of dual rubber system in toughening styrene maleic anhydride copolymers

Styrene maleic anhydride (SMA) copolymers were toughened by blending with two distinctly different rubber modifiers: styrene‐butadiene‐styrene (SBS) block copolymer and methacrylated butadiene‐styrene emulsion‐made graft copolymer (MBS). The modifiers were used both individually and in combination for the examination of their roles in toughening SMA. SMA was miscible with poly(methylmethacrylate) shell of MBS, whereas it was partially miscible with the polystyrene (PS) phase of SBS. When 40–50% of SBS was used in blends, the PS phase of SBS became immiscible with SMA. SBS did not improve the Izod impact strength of SMA appreciably. A prominent synergistic toughening effect was experimentally observed when SBS and MBS were used in combination in brittle SMA. This effect may be attributed to the fact that the large SBS particles initiate crazes and small MBS particles with good adhesion to SMA matrix improve the ligament thickness, which may play a critical role in craze growth and termination. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2260–2267, 2003     

Morphology and mechanical properties of ABS blends prepared from emulsion‐polymerized PB‐g‐SAN impact modifier with AIBN as initiator

A series of PB‐g‐SAN impact modifiers (polybutadiene particles grafted by styrene and acrylonitrile) are synthesized by seed emulsion copolymerization initiated by oil‐soluble initiator, azobisiobutyronitrile (AIBN). The ABS blends are obtained by mixing SAN resin with PB‐g‐SAN impact modifiers. The mechanical behavior and the phase morphology of ABS blends are investigated. The graft degree (GD) and grafting efficiency (GE) are investigated, and the high GD shows that AIBN has a fine initiating ability in emulsion grafting of PB‐g‐SAN impact modifiers. The morphology of the rubber particles is observed by the transmission electron microscopy (TEM). The TEM photograph shows that the PB‐g‐SAN impact modifier initiated by AIBN is more likely to form subinclusion inside the rubber particles. The dynamic mechanical analysis on ABS blends shows that the subinclusion inside the rubber phase strongly influences the T_g, maximum tan δ, and the storage modulus of the rubber phase. The mechanical test indicates that the ABS blends, which have the small and uniform subinclusions dispersed in the rubber particles, have the maximum impact strength. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Properties and preparation of compatibilized nylon 6 nanocomposites/ABS blends using functionalized metallocene polyolefin elastomer. I. Impact properties

The impact behaviors of nanoclay‐filled nylon 6 (nano‐nylon 6) blended with poly(acrylonitrile–butadiene–styrene) terpolymers (ABS) prepared through a twin screw mixing process were investigated here using metallocene polyethylene grafted maleic anhydride (POE‐g‐MA) as a compatibilizer to enhance the interface interaction. No clear effect of compatibilizer on the dispersion of clay and crystalline structure of nano‐nylon 6 has been observed. In view of morphology and rheological behaviors, the effect of compatibilizer on the mechanical properties could be elucidated. It is found that impact strength increases with the addition of compatibilizer at various ABS compositions. Similar effects are also observed with decreasing test temperature at the nano‐nylon 6/ABS blend composition of 80/20. As for thermal properties, the heat distortion temperature shows a marginal decrease in the nano‐nylon 6/ABS blends. Rheological behavior indicates that increased viscosity is found for the investigated compatibilized systems. Through morphology observations, the etched ABS particle sizes tend to decrease with the addition of compatibilizer for the blends, but are larger with higher contents of ABS concentrations. Those observations account for impact behaviors of the investigated blends. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1364–1371, 2006