Carbon nanotube/polypropylene/polycarbonate conductive nanocomposite films: Preparation and characterization

In this study, CNT/PP/PC conductive composite films were prepared by compounding PP (polypropylene)/PC (polycarbonate) (1:1) and carbon nanotubes (CNT) using a physical blending and hot pressing method. Next, Fourier transform infrared spectroscopy, thermogravimetric analysis, differential scanning calorimetry, and water contact angle measurement are conducted in order to characterize the properties of CNT/PP/PC conductive films. The results showed there is no chemical reaction inside the PP/PC composite film with the addition of CNT. Neither the CNT composite film containing 3 wt% nor the control film decomposed thermally within 220°C. The water contact angle increased from 88.5° for the control film to 110.99° for the composite film containing 3 wt% CNT. This indicates that the film has good thermal stability and hydrophobic properties. The percolation threshold was obtained when the content of CNT was 3 wt%, and the best conductivity of the CNT/PP/PC composite film was 5.53 S/m at this time. In order to improve the tensile properties of the film, a small amount of polyurethane (TPU) was added to the film, and the maximum tensile strength was 24.91 Mpa when the content of TPU was 6.7%. This study can provide a strategy for the practical application of flexible electronic devices.     

Probing toughness of polycarbonate (PC: ductile and brittle)/polypropylene (PP) blends and talc-triggered PC/PP brittle composites with diverse impact fracture parameters

Polycarbonates (PCs) are commonly used as a blend and a composite to achieve pecuniary advantages and dimensional stability. While the toughness of a homogeneous PC matrix has been extensively investigated, examination for the toughness of heterogeneous blend systems such as PC/polypropylene (PP) blends has been limited. Furthermore, recent interest in highly flowable PCs (low-molecular-weight PCs with low ductility) has surfaced due to the large and geometrically complex plastic parts. Herein, the toughness for PC/PP blends and PC/PP/talc composites in a ductile and a brittle PC matrix was explored by using various toughness measurements such as notched Izod impact strength, falling dart impact, boss quasi-static energy/impact energy, and tensile toughness tests. In a ductile PC matrix [melt flow index (MFI) = 8], the incorporation of PP gradually reduced the toughness. On the other hand, the toughness was improved by 450% at 2 wt % PP in a brittle PC matrix (MFI = 19). Similarly, in the talc-induced brittle PC matrix, the toughness was enhanced at the PP loading from 2 to 10 wt %. The density of PC/PP blends was gradually reduced from 1.19 to 1.10 g cm⁻³ with increasing PP concentration from 0 to 20 wt %. Degradation, density, thermal behaviors, and morphology were also investigated. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47110.     

Morphological,thermal, and mechanical properties of polypropylene/polycarbonate blend

This work deals with the effect of compatibilizer on the morphological, thermal, rheological, and mechanical properties of polypropylene/polycarbonate (PP/ PC) blends. The blends, containing between 0 to 30 vol % of polycarbonate and a compatibilizer, were prepared by means of a twin-screw extruder. The compatibilizer was produced by grafting glycidyl methacrylate (GMA) onto polypropylene in the molten state. Blend morphologies were controlled by adding PP-g-GMA as compatibilizer during melt processing, thus changing dispersion and interfacial adhesion of the polycarbonate phase. With PP-g-GMA, volume fractions increased from 2.5 to 20, and much finer dispersions of discrete polycarbonate phase with average domain sizes decreased from 35 to 3 μm were obtained. The WAXD spectra showed that the crystal structure of neat PP was different from that in blends. The DSC results suggested that the degree of crystallization of PP in blends decreased as PC content and compatibilizer increased. The mechanical properties significantly changed after addition of PP-g-GMA. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 63: 1857–1863, 1997     

Mechanical properties and morphological structures relationship of blends based on sulfated EPDM ionomer and polypropylene

The mechanical properties and morphological structures of blends based on Zn²⁺ neutralized low degree sulfated ethylene propylene diene monomer rubber (Zn–SEPDM) ionomer and polypropylene (PP) were studied. It was found that Zn²⁺ neutralized low degree sulfated EPDM ionomer and PP blends, which are new thermoplastic elastomeric materials, have better mechanical properties than those of PP/EPDM blend. Theoretical analysis of tensile data suggests that there is an increase of the extent of interaction between PP and EPDM in the presence of a low degree of Zn²⁺, which is also an indicator of better interfacial adhesion between PP and Zn–SEPDM than that between PP and EPDM. SEM results proved that the finer dispersed phase sizes and the shorter interparticle distances are the main reasons for the improved mechanical properties of the PP/EPDM blend. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1504–1510, 2004     

Rheological behavior of polypropylene/novolac blends

The rheological behavior of polypropylene/novolac blends was investigated with special reference to the effects of the blend ratio, compatibilization, and dynamic cure. The polypropylene and all the polypropylene/novolac blends presented evidence of shear‐thinning behavior. The novolac, compatibilizer, and dynamic cure had dramatic effects on the rheological behavior of the polypropylene. Various rheological plots, including plots of the viscosity, storage modulus, loss modulus, and loss angle, Han plots, and Cole–Cole plots, were used to analyze the polypropylene/novolac blends. The results showed that the compatibilization together with the dynamic cure could increase the viscosity and modulus because of the formation of a grafting polymer between the maleic anhydride grafted polypropylene and the curing novolac resin. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Compatibility enhancement of ABS/polycarbonate blends

The effects of blend composition, melt viscosity of poly(acrylonitrile-butadiene-styrene) (ABS), and compatibilizing effect of poly(methyl methacrylate) (PMMA) on mechanical properties of ABS/polycarbonate (PC) blends at ABS-rich compositions were studied. As the content of PC was increased, impact strength and Vicat softening temperature (VST) were increased. As the melt viscosity of ABS was increased near to that of PC, finer distribution of dispersed PC phase and consequent enhanced impact strength and VST were observed. The compatibilizing effect of PMMA can be ascer-tained from the enhanced properties of ¼-inch notch impact strength, VST, tensilestrength, and the morphology observed by a scanning electron microscope. The improved adhesion of the ABS/PC interface by PMMA changed the fracture mechanism and reduced the notch sensitivity of blends. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 533–542, 1998     

Effect of nano‐silica filler on the rheological and morphological properties of polypropylene/liquid‐crystalline polymer blends

A fumed hydrophilic nano‐silica‐filled polypropylene (PP) composite was blended with a liquid‐crystalline polymer (LCP; Rodrun LC5000). The preblended polymer blend was extruded through a capillary die; this was followed by a series of rheological and morphological characterizations. The viscosity of the PP matrix increased with the addition of the hydrophilic nano‐silica. At shear rates between 50 and 200 s^?1, the composite displays marked shear‐thinning characteristics. However, the incorporation of LC5000 in the PP composite eliminated the shear‐thinning characteristic, which suggests that LC5000 destroyed the agglomerated nano‐silica network in the PP matrix. Although the viscosity ratio of LCP/PP was reduced after the addition of nano‐silica fillers, the LCP phases existed as droplets and ellipsoids. The nano‐silicas were concentrated in the LC5000 phase, which hindered the formation of LCP fibers when processed at high shear deformation. We carried out surface modification of the hydrophilic nano‐silica to investigate the effect of modified nano‐silica (M‐silica) on the morphology of the PP/LC5000 blend system. Ethanol was successfully grafted onto the nano‐silica surface with a controlled grafting ratio. The viscosity was reduced for PP filled with ethanol‐M‐silica when compared to the system filled with untreated hydrophilic nano‐silica. The LC5000 in the (PP/M‐silica)/LC5000 blend existed mainly in the form of fibrils. At high shear rates (e.g., 3000 s^?1), the LC5000 fibril network was formed at the skin region of the extrudates. The exclusion of nano‐silica in the LC5000 phase and the increased viscosity of the matrix were responsible for the morphological changes of the LCP phase. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 1484–1492, 2003     

Melting,nonisothermal crystallization behavior and morphology of polypropylene/random ethylene—propylene copolymer blends

The melting, nonisothermal crystallization behavior and morphology of blends of polypropylene (PP) with random ethylene–propylene copolymer (PP‐R) were studied by differential scanning calorimetry, polarized optical microscopy, scanning electron microscopy, and X‐ray diffraction. The results showed that PP and PP‐R were very miscible and cocrystallizable. Modified Avrami analysis was used to analyze the nonisothermal crystallization kinetics of the blends. The values of the Avrami exponent indicated that the crystallization nucleation of the blends was heterogeneous, the growth of the spherulites was tridimensional, and the crystallization mechanism of PP was not affected by PP‐R. The crystallization activation energy was estimated using the Kissinger method. An interesting result was obtained with the modified Avrami analysis and the Kissinger method, whose conclusions were in good agreement. The addition of a minor PP‐R phase favored an increase in the overall crystallization rate of PP. Maximum enhancing effect wass found to occur with a PP‐R content of 20 wt %. The relationship between the composition and the morphology of the blends is discussed. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 670–678, 2006     

A compatibilized composite of recycled polypropylene filled with cellulosic fiber from recycled corrugated paper board: Mechanical properties,morphology, and thermal behavior

This article deals with the feasibility of using recycled corrugated paper board (rPF) as the reinforcing material for recycled plastics. The composites of recycled polypropylene (rPP) and rPF were prepared by extrusion compounding and injection molding, and the rPP/rPF composites compatibilized by maleic anhydride grafted PP (PP‐g‐MA), maleic anhydride grafted ethylene‐1‐octene copolymer (POE‐g‐MA), and maleic anhydride grafted styrene‐ethylene‐butylene‐styrene copolymer (SEBS‐g‐MA) were also prepared. The crystallization and melting behavior, mechanical properties, thermal stability, and morphology of these composites were studied. The results indicated that rPF promoted the crystallization, enhanced the strength and toughness of rPP/rPF composites to some extent while decreased thermal stability at the same time. PP‐g‐MA and POE‐g‐MA improved the dispersion and interface adhesion of rPF, and further upgraded the mechanical properties and vicat softening temperatures. Among these compatibilizers, PP‐g‐MA was most favorable to the strength improvement while POE‐g‐MA was most favorable to the toughness improvement. As for SEBS‐g‐MA, it had no obvious modification effect. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Thermal behavior and morphological and rheological properties of polypropylene and novel elastomeric ethylene copolymer blends

The thermal behavior including melting and crystallization behavior and morphological and rheological properties of the blends based on an isotactic polypropylene and a novel maleated elastomeric ethylene copolymer were investigated in this work. The addition of an elastomer to polypropylene (PP) was found not to change the PP crystalline structure significantly when cooled quickly from the melt. On recrystallization at a lower cooling rate, the elastomer promotes the formation of β?pseudohexagonal PP in PP‐rich blends. In elastomer‐rich compositions, heterogeneous nucleation is hindered and homogeneous nucleation takes place. These phenomena are revealed by morphology observation: that, with increasing of the elastomer content, the system undergoes PP continuous, dual‐phase continuity and PP‐dispersed morphologies. The blend viscosity at a low shear rate range increases continuously with increasing elastomer content and shows positive deviations from the additivity rule. In the terminal zone, the dynamic storage modulus of the blends shows positive deviation from the simple mixing rule and the maximum deviation lies in the composition range of dual‐phase continuity which could be caused by a large increase in the interfacial tension. The Cox–Merz rule does not hold for the blends because of the two‐phase heterogeneous structure and its variation in steady and oscillatory shear flow. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 3430–3439, 2002     

聚碳酸酯／聚丙烯共混物的结构与性能

在过氧化二异丙苯的引发下，用反应挤出的方法制备了聚丙烯接枝甲基丙烯酸环氧丙酯。用双螺杆挤出机制务了不同组成的聚碳酸酯／聚丙烯及ＰＣ／ＰＰ－ｇ－ＧＭＡ／ＰＰ的共混物。用电子显微镜观察了不同经组成的形态，与ＰＰ／ＰＣ共混体系相比，ＰＣ／ＰＰ／ＰＰ－ｇ－ＧＭＡ体系中的ＰＣ一ＰＰ中分散相尺寸明显降低，ＰＰ－ｇ－ＧＭＡ加入改变聚丙烯在共混物中的晶体结构及提高了聚丙烯的结晶温度，同时ＰＰ－ｇ－ＧＭＡ的加入对共     

Effects of vibration blending on the subsequent crystallization behavior of polycarbonate/polypropylene blends

The effects of blending in a novel vibration internal mixer on the subsequent multiple crystallization of 70/30 w/w polycarbonate (PC)/polypropylene (PP) were investigated by differential scanning calorimetry, wide‐angle X‐ray diffractogram, and microscopy. The vibration internal mixer was reformed from a conventional internal mixer through parallel superposition of an oscillatory shear on a steady shear. For this polypropylene‐minor phase blend, three possible crystallization peaks were observed. The crystallization behavior was sensitive to the sizes and the size distribution of the dispersed polypropylene droplets. Larger amplitude and/or higher‐frequency vibration produced more small droplets (<2 μm) and increased the number of medium droplets (2–8 μm) as a result of the spatially wider and temporally quicker variation of shear rate. The resulting subsequent low‐temperature crystallization peak became larger and shifted to lower temperature, and the intermediate‐temperature peak became obvious. On the contrary, the coalescence of small droplets, resulting from the heating treatment, weakened the low‐temperature peak but strengthened the intermediate‐temperature peak and rendered the high‐temperature peak to be wider. Mixing at the too high amplitude produced the unstable, partially cocontinuous phase morphology restricting the medium droplets and enlarging the surface area, such that the intermediate‐temperature crystallization peak did not appear. Multiple crystallization was related to phase morphology and the nucleation density as well as surface effects. Double‐fusion endotherms of the PP component were also observed, corresponding to the melting of different forms of polypropylene crystals. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 92–103, 2002     

Surfactant assisted processing of carbon nanotube/polypropylene composites: Impact of surfactants on the matrix polymer

Multiwalled carbon nanotubes (MWCNT) were dispersed in presence of various surfactants and introduced into isotactic polypropylene (PP) via melt blending. The effect of the surfactants on the crystallization and mechanical properties was studied on the injection molded specimens by isothermal differential scanning calorimetry and tensile tests, respectively. The results reveal that the presence of surfactants affects the mechanical and thermal properties of the nanocomposite. This information is supported by thermogravimetric analysis of the surfactants to examine their behavior at temperatures relevant for the processing of PP. In addition, they have to be taken into account as a third phase between the MWCNT and polymeric matrix, affecting the crystallization and failure behavior of PP or causing the formation of pores at elevated temperatures. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Mechanical,thermal, and morphological properties of maleic anhydride‐g‐polypropylene compatibilized and chemically modified banana‐fiber‐reinforced polypropylene composites

Composites were prepared with chemically modified banana fibers in polypropylene (PP). The effects of 40‐mm fiber loading and resin modification on the physical, mechanical, thermal, and morphological properties of the composites were evaluated with scanning electron microscopy (SEM), thermogravimetric analysis (TGA), Infrared (IR) spectroscopy, and so on. Maleic anhydride grafted polypropylene (MA‐g‐PP) compatibilizer was used to improve the fiber‐matrix adhesion. SEM studies carried out on fractured specimens indicated poor dispersion in the unmodified fiber composites and improved adhesion and uniform dispersion in the treated composites. A fiber loading of 15 vol % in the treated composites was optimum, with maximum mechanical properties and thermal stability evident. The composite with 5% MA‐g‐PP concentration at a 15% fiber volume showed an 80% increase in impact strength, a 48% increase in flexural strength, a 125% increase in flexural modulus, a 33% increase in tensile strength, and an 82% increase in tensile modulus, whereas the heat deflection temperature increased by 18°C. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Mechanical,thermal, and microstructural properties of polypropylene/polyamide‐6/styrene‐ethylene‐butadiene‐styrene polymer alloys

Interfacial agents as compatibilizers have recently been introduced into polymer blends to improve the microstructure and mechanical properties of thermoplastics. In this way, it is possible to prepare a mixture of polymeric materials that can have superior mechanical properties over a wide temperature range. In this study, an incompatible blend of polypropylene (PP) and polyamide‐6 (PA₆) were made compatible by the addition of 10% styrene–ethylene–butadiene–styrene copolymer (SEBS). The mixing operation was conducted by using a twin‐screw extruder. The morphology and the compatibility of the mixtures were examined by SEM and DSC techniques. Furthermore, the elastic modulus, tensile and yield strengths, percentage elongation, hardness, melt flow index, Izod impact resistance, heat deflection temperature (HDT), and Vicat softening point values of polymer alloys of various ratios were determined. It was found that the addition of SEBS to the structures decreased the tensile strength, yield strength, elastic modulus, and hardness, whereas it increased the Izod impact strength and percentage elongation values. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3485–3491, 2003     

Bamboo fiber reinforced polypropylene composites and their mechanical,thermal, and morphological properties

Short bamboo fiber reinforced polypropylene composites were prepared by incorporation of various loadings of chemically modified bamboo fibers. Maleic anhydride grafted polypropylene (MA‐g‐PP) was used as compatibilizer to improve fiber–matrix adhesion. The effects of bamboo fiber loading and modification of the resin on the physical, mechanical, thermal, and morphological properties of the bamboo reinforced modified PP composites were studied. Scanning electron microscopy studies of the composites were carried out on the interface and fractured surfaces. Thermogravimetric analysis and IR spectroscopy were also carried out. At 50% volume fraction of the extracted bamboo fiber in the composites, considerable increase in mechanical properties like impact, flexural, tensile, and thermal behavior like heat deflection temperature were observed. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Nonisothermal crystallization,melting behavior,and morphology of polypropylene/metallocene‐catalyzed polyethylene blends

The nonisothermal crystallization, melting behavior, and morphology of blends of polypropylene (PP) and a metallocene‐catalyzed polyethylene (mPE) elastomer were studied with differential scanning calorimetry, scanning electron microscopy, polarized optical microscopy, and X‐ray diffraction. The results showed that PP and mPE were partially miscible and could form some cocrystallization, although the extent was very small. A modified Avrami analysis and the Mo method were used to analyze the nonisothermal crystallization kinetics of the blends. The values of the Avrami exponent indicated that the crystallization nucleation of the blends was homogeneous, the growth of the spherulites was three‐dimensional, and the crystallization mechanism of PP was not affected by mPE. The crystallization activation energy was estimated with the Kissinger method. Interesting results were obtained with the modified Avrami analysis and Mo and Kissinger methods, and the conclusions were in good agreement. The addition of less mPE increased the overall crystallization rate of PP. The relationship between the composition and morphology of the blends was examined. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1203–1210, 2004     

Effect of process parameters and composition on mechanical,thermal, and morphological properties of polypropylene/sawdust composites

Polypropylene/sawdust composites have been prepared according to a statistical experimental design, with varying sawdust and compatibilizer (maleic anhydride grafted PP) concentrations. To investigate process conditions, composites were first extruded in a twin screw extruder coupled to a Haake torque rheometer, without degassing, and then reextruded in a Werner Pfleiderer twin screw extruder, with two degassing zones. Process conditions were analyzed according to statistical techniques. Effect of the variables on mechanical properties was assessed through flexural modulus, tensile strength, and percent elongation at break and morphology was assessed by scanning electron microscopy. Comparison between the extruded and reextruded compounds indicated the need to reduce moisture, prior to and during processing, as well as the need of effective mixing of the compounds. Sawdust concentration showed to be the variable which affected most all properties assessed. Increase in sawdust concentration resulted in increased composite stiffness. The presence of the compatibilizer caused a slight increase in tensile strength and reduction in percent elongation at break, indicating improved adhesion at the PP/sawdust interface. The reprocessed compounds were also analyzed by differential scanning calorimetry. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Mechanical properties,morphological structure,and thermal behavior of dynamically photocrosslinked PP/EPDM blends

A dynamically photocrosslinked polypropylene (PP)/ethylene–propylene–diene (EPDM) rubber thermoplastic elastomer was prepared by simultaneously exposing the elastomer to UV light while melt‐mixing in the presence of a photoinitiator as well as a crosslinking agent. The effects of dynamic photocrosslinking and blend composition on the mechanical properties, morphological structure, and thermal behavior of PP/EPDM blends were investigated. The results showed that after photocrosslinking, tensile strength, modulus of elasticity, and elongation at break were improved greatly. Moreover, the notched Izod impact strength was obviously enhanced compared with corresponding uncrosslinked blend. Scanning electron microscopy (SEM) morphological analysis showed that for uncrosslinked PP/EPDM blends, the cavitation of EPDM particles was the main toughening mechanism; whereas for dynamically photocrosslinked blends, shear yielding of matrix became the main energy absorption mechanism. The DSC curves showed that for each dynamically photocrosslinked PP/EPDM blend, there was a new smaller melting peak at about 152°C together with a main melting peak at about 166°C. Dynamic mechanical thermal analysis (DMTA) indicated that the compatibility between EPDM and PP was improved by dynamic photocrosslinking. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3371–3380, 2004     

Study on processing of ultrahigh molecular weight polyethylene/polypropylene blends

The processing of ultrahigh molecular weight polyethylene (UHMWPE) by the addition of polypropylene (PP) and high‐density polyethylene (HDPE) was investigated. The results show that the addition of PP improves the processability of UHMWPE more effectively than does the addition of HDPE. UHMWPE/PP blends can be effectively processed with a twin‐roller and general single‐screw extruder. In the extrusion of UHMWPE/PP blends, PP is enriched at the surface of the blend adjacent to the barrel wall, thus increasing the frictional force on the wall; the conveyance of the solid down to the channel can then be carried out. The melt pool against the active flight flank exerts a considerable pressure on the UHMWPE powder in the passive flight flank, which overcomes the hard compaction of UHMWPE. The PP penetrates into the gaps between the particles, acting as a heat‐transfer agent and adhesive, thus enhancing the heat‐transfer ability in the material. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 977–985, 2004