Removal of Cr(VI) from aqueous solution using amino‐modified Fe3O4–SiO2–chitosan magnetic microspheres with high acid resistance and adsorption capacity

A novel, bioadsorbent material of polyethylenimine‐modified magnetic chitosan microspheres enwrapping magnetic silica nanoparticles (Fe₃O₄–SiO₂–CTS‐PEI) was prepared under relatively mild conditions. The characterization results indicated that the adsorbent exhibited high acid resistance and magnetic responsiveness. The Fe₃O₄ loss of the adsorbent was measured as 0.09% after immersion in pH 2.0 water for 24 h, and the saturated magnetization was 11.7 emu/g. The introduction of PEI obviously improved the adsorption capacity of Cr(VI) onto the adsorbent by approximately 2.5 times. The adsorption isotherms and kinetics preferably fit the Langmuir model and the pseudo‐second‐order model. The maximum adsorption capacity was determined as 236.4 mg/g at 25°C, which was much improved compared to other magnetic chitosan materials, and the equilibrium was reached within 60 to 120 min. The obtained thermodynamic parameters revealed the spontaneous and endothermic nature of the adsorption process. Furthermore, the Cr(VI)‐adsorbed adsorbent could be effectively regenerated using a 0.1 mol/L NaOH solution, and the adsorbent showed a good reusability. Due to the properties of good acid resistance, strong magnetic responsiveness, high adsorption capacity, and relatively rapid adsorption rate, the Fe₃O₄–SiO₂–CTS‐PEI microspheres have a potential use in Cr(VI) removal from acidic wastewater. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43078.     

Preparation and adsorption mechanism of polyvinyl alcohol/graphene oxide-sodium alginate nanocomposite hydrogel with high Pb(II) adsorption capacity

A series of polyvinyl alcohol (PVA)/graphene oxide (GO)-sodium alginate (SA) nanocomposite hydrogel beads were prepared through in situ crosslinking for Pb²⁺ removal. It was found that PVA and SA molecules were intercalated into GO layers through hydrogen bonding interactions, leading to the destruction of orderly structure of GO, while GO uniformly distributed in PVA matrix. With increasing PVA solution concentration, the hydrogel beads became more regular, a large number of polygonal pores with thin walls and open pores formed, the average pore size decreased, and the dense network structure formed. Meanwhile, the permeability of the composite hydrogel decreased, leading to the decline of Pb²⁺ adsorption capacity of the composite hydrogel. With increasing GO content, the ballability of the hydrogel beads was weakened, the pore size increased, and relatively loose network structure formed, resulting in an increase in permeability and Pb²⁺ adsorption capacity of the hydrogel, reaching up to 279.43 mg g⁻¹. Moreover, the composite hydrogel presented relatively good reusability for Pb²⁺ removal. The adsorption mechanism was explored and showed that the adsorption system of the composite hydrogel belonged to the second-order kinetic model and fitted Langmuir adsorption isotherm model for Pb²⁺ removal, which might be mono-layer chemical adsorption. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47318.     

Magnetic and K+-cross-linked kappa-carrageenan nanocomposite beads and adsorption of crystal violet

Biopolymer-based magnetic beads, composed of kappa-carrageenan (κ-Car) and Fe₃O₄ nanoparticles, were synthesized. The magnetic beads were prepared through in situ precipitation of Fe²⁺/Fe³⁺ ions in the presence of carrageenan and subsequently treating with K⁺ solution. The structure of magnetic kappa-carrageenan beads (mκ-Carb) was characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), vibrating sample magnetometer, and thermal gravimetric analysis techniques. According to SEM micrographs, an undulant and coarse structure with cubic-shaped sections was obtained when the magnetic nanoparticles were incorporated in composition of beads. The TEM image confirmed the formation of magnetic nanoparticles with an average size of 3–7 nm. The synthesized beads were examined as adsorbent to remove crystal violet dye from aqueous solutions. It was found that due to coarse surface, the rate of dye adsorption on magnetic beads can be improved slightly. The experimental adsorption kinetics was analyzed according to pseudo-first-order and pseudo-second-order kinetic models and the adsorption kinetics followed well the pseudo-second-order model. Isotherm adsorption data of dye on beads were modeled according to Langmuir and Freundlich isotherm models. The results revealed that the experimental data have the best fit to Langmuir isotherm model, and maximum adsorption capacity of beads for dye obtained was 84.7 mg/g. The influence of pH on the variation of adsorption capacity of beads for crystal violet was not considerable. The thermodynamic parameters indicated that the adsorption of CV dye on beads is spontaneous.     

Facile preparation of magnetic chitosan modified with thiosemicarbazide for adsorption of copper ions from aqueous solution

In this study, magnetic chitosan modified with thiosemicarbazide (TSC‐Fe₃O₄/CTS) was facilely synthesized with glutaraldehyde as the crosslinker, and its application for removal of Cu(II) ions was investigated. The as‐prepared TSC‐Fe₃O₄/CTS was characterized by Fourier transform infrared spectroscopy (FTIR), X‐ray powder diffraction (XRD), and scanning electron microscopy (SEM). The results showed that TSC‐Fe₃O₄/CTS has high adsorption capacity and selectivity towards Cu(II) ions. Adsorption experiments were carried out with different parameters such as pH, solution temperature, contact time and initial concentration of Cu(II) ions. The adsorption process was better described by the pseudo‐second‐order model. The sorption equilibrium data was fitted well with the Langmuir isotherm model and the maximum adsorption capacity toward Cu(II) ions was 256.62 mg/g. The thermodynamic parameters indicated that the adsorption process of Cu(II) ions was exothermic spontaneous reaction. Moreover, this adsorbent showed excellent reusability and the adsorption property remained stable after five cycles. This adsorbent is believed to be one of the promising and favorable adsorbent for the removal of Cu(II) ions from aqueous solution. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44528.     

Single step modification of micrometer-sized polystyrene particles by electromagnetic polyaniline and sorption of chromium(VI) metal ions from water

This article describes a single-step reproducible approach for the surface modification of micrometer-sized polystyrene (PS) core particles to prepare electromagnetic PS/polyaniline–Fe₃O₄ (PS/PANi–Fe₃O₄) composite particles. The electromagnetic PANi–Fe₃O₄ shell was formed by simultaneous seeded chemical oxidative polymerization of aniline and precipitation of Fe₃O₄ nanoparticles. The weight ratio of PS to aniline was optimized to produce core–shell structure. PS/PANi–Fe₃O₄ composite particles were used as adsorbent for the removal of Cr(VI) via anion-exchange mechanism. The composite particles possessed enough magnetic property for magnetic separation. The adsorption was highly pH dependent. Adsorption efficiency reached 100% at pH 2 in 120 min when 0.05 g of composite particles was mixed with 30 mL 5 mg L⁻¹ Cr(VI) solution. The adsorption isotherm fitted best with Freundlich model and maximum adsorption capacity approached 20.289 mg g⁻¹ at 323 K. The prepared composite was found to be an useful adsorbent for the removal of soluble Cr(VI) ions. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47524.     

Removal of Pb(ii) ions from aqueous solution using a novel composite adsorbent of Fe3o4/PVA/spent coffee grounds

ABSTRACT

A novel magnetic composite prepared from Fe₃O₄, poly(vinyl alcohol) and alkaline pretreated spent coffee grounds (Fe₃O₄/PVA/APSCGs) was utilized for the first time as an adsorbent for adsorption of Pb(II) ions after carefully characterizing it by various techniques (XRD, FTIR, SEM, EDX). The obtained results indicated that the adsorption was spontaneous, endothermic, fitting well with both Langmuir and Freundlich models, and more suitable to be described by the second-order kinetic model. The maximum adsorption capacity of Fe₃O₄/PVA/APSCGs for Pb(II) at optimum conditions (pH of 5, contact time of 24 h, APSCGs:Fe₃O₄ weight ratio of 4:1) was found to be 0.275 mmol.g^?1. Recycling study showed a good reusability of the composite with removal efficiency maintained at 78.12% after five continuous adsorption-desorption cycles.     

Adsorption of Cr(VI) on Cross‐Linked Chitosan Beads

Abstract

A possibility of Cr(VI) removal by the adsorption method is discussed in the paper. An adsorbent were hydrogel chitosan beads are produced by the phase inversion method (by changing pH). The possibility of removing Cr(VI) ions by both pure chitosan hydrogel and its chelate compounds (chitosan cross‐linked with Cu(II) and Ag(I) ions) was investigated. The adsorption proceeded from the solutions of potassium dichromate and ammonium dichromate (NH₄)₂Cr₂O₇ and K₂Cr₂O₇. The process rates and adsorption isotherms were determined and described by relevant equations. The process rate was described by the pseudo‐ and second‐order equations, and adsorption equilibria by the Langmuir equations. A slight advantageous change in adsorption properties of chitosan beads was revealed after cross‐linking (for chromium concentration up to 10 g/dm³). A maximum adsorption was 1.1 g_Cr/g chitosan. Results of the studies show that chitosan hydrogel proves useful in the removal of Cr(VI) ions, additionally, cross‐linking with Cu(II) and Ag(I) ions has an advantageous effect in the case of low‐concentrated solutions.     

Mussel‐inspired magnetic adsorbent: Adsorption/reduction treatment for the toxic Cr(VI) from simulated wastewater

A novel magnetic adsorbent, poly(catechol‐1,4‐butanediamine)‐coated Fe₃O₄ composite (Fe₃O₄@PCBA), was successfully fabricated via an easy and gentle method according to the mussel‐inspired adhesion property of polydopamine. Effects of many factors on the adsorption performance of Fe₃O₄@PCBA for Cr(VI) were investigated, including temperature, pH value, contacting time, adsorbent dosage, and initial Cr(VI) concentration. The thermodynamics, adsorption isotherm, kinetics, and intraparticle diffusion of adsorption were also studied systematically. Results indicated that the removal rate of Cr(VI) was approximately close to 100% when the initial concentration was less than 120 mg/L, and the maximum uptake capacity of Fe₃O₄@PCBA for Cr(VI) was 280.11 mg/g complied with Langmuir isotherm model. Accordingly, the nocuous Cr(VI) could be partially reduced to Cr(III) during the adsorption period. Hopefully, this strategy could be extended to prepare series of magnetic Fe₃O₄@catechol–amine adsorbents with different amino and phenolic hydroxyl groups for Cr(VI) removal. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46530.     

Synthesis of Fe2O3-coated and HCl-treated bauxite ore waste for the adsorption of arsenic (III) from aqueous solution: Isotherm and kinetic models

The present work has focused on the removal of arsenic (III) using two effective adsorbents such as red mud treated with HCl and coated with Fe₂O₃. Adsorption of As (III) was performed by the function of pH, adsorbent dose, contact time, initial ion concentration, and the appropriate conditions for adsorption were determined. The characterization studies of the adsorbent were analyzed using X-ray diffraction, X-ray fluorescence, Brauner–Emmett–Teller, scanning electron microscope, and FTIR spectroscopy. The result of the studies shows that the adsorbent is suitable for the effective removal of As (III) ions. Batch adsorption process showed that the maximum adsorption occurred at Fe₂O₃-coated red mud. The equilibrium data were well fitted to the nonlinear Langmuir isotherm model and the maximum adsorption capacity (q_m) of Fe₂O₃-coated red mud was found to be 21.85?mg?g^?1 which indicates that Fe₂O₃-coated red mud had more adsorption capacity. In the Freundlich isotherm, the experimentally obtained n value of Fe₂O₃-coated red mud was 2.393 which indicates the favorable adsorption of As (III) on the adsorbent. Dubinin–Radushkevich isotherm confirms that the adsorption process is physical in nature. Furthermore, the adsorption kinetic studies followed the pseudo-first-order model. All the results concluded that Fe₂O₃-coated red mud can be considered as a cost-effective and potential adsorbent for As (III) removal.     

Application of magnetite modified with aluminum/silica to adsorb phosphate in aqueous solution

BACKGROUND: Phosphate is one of the main contaminants responsible for the eutrophication of surface waters, and adsorption is a potential treatment method for this pollutant. A magnetic adsorbent manufactured from magnetite (Fe₃O₄) can be recovered easily from treated water by magnetic force, without requiring further downstream treatment. In this research, the surface of magnetite modified with aluminum and silica (Al/SiO₂/Fe₃O₄) was used to adsorb phosphate in an aqueous solution in a batch system. RESULTS: The optimum solution pH for phosphate adsorption by Al/SiO₂/Fe₃O₄ was found to be 4.5. The phosphate adsorption behavior of Al/SiO₂/Fe₃O₄ was in good agreement with both the Langmuir and Freundlich adsorption isotherm, and the maximum adsorption capacity (q_m) and Gibbs free energy of phosphate was 25.64 mg g^?1 and ? 21.47 kJ mol^?1, respectively. A pseudo‐second‐order model could best describe the adsorption kinetics, and the derived activation energy was 3.52 kJ mol^?1. The optimum condition to desorb phosphate from Al/SiO₂/Fe₃O₄ is provided by a solution with 0.05 mol L^?1 NaOH. CONCLUSIONS: Magnetic adsorbent is a potential material for a water treatment method. The results of this study will be helpful in the development of aluminum modified silica magnetic adsorbents that can be used to remove phosphate in aqueous solution. Copyright © 2011 Society of Chemical Industry     

Self‐assembly of alginate/polyethyleneimine multilayer onto magnetic microspheres as an effective adsorbent for removal of anionic dyes

A novel magnetic adsorbent alginate/polyethyleneimine (ALG/PEI)_n/MN was developed for removal of anionic dyes from aqueous solution in this study. (ALG/PEI)_n/MN was prepared by depositing ALG/PEI multi‐layers onto amine‐modified Fe₃O₄ microspheres through layer‐by‐layer method. The morphologies and structures of the adsorbent were characterized by scanning electron microscopy, X‐ray diffractometer, and Fourier transform infrared spectrometer, respectively, and its performance in adsorption of anionic dye (acid orange 10, AO10) under varied experimental conditions were also investigated. The results revealed that the uptake capacity of AO10 by (ALG/PEI)_n/MN increased with the number of coated (ALG/PEI) bilayer on the adsorbents, and the maximum adsorption capacity for AO10 by (ALG/PEI)₄MN was 246.3 mg g^?1 at 25 °C. The adsorption process was exothermic and well described by the pseudo‐second order kinetic model and the Langmuir isothermal model. Moreover, (ALG/PEI)₄/MN showed good reusability and excellent magnetic separability. All the results demonstrate that (ALG/PEI)₄/MN is a potential recyclable adsorbent for removal of anionic dyes from wastewater. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45876.     

Investigation of α‐iron oxide‐coated polymeric nanocomposites capacity for efficient heavy metal removal from aqueous solution

In the present study, PS@α‐Fe₂O₃ nanocomposites were prepared by chemical microemulsion polymerization approach and the ability of magnetic beads to remove Cu(II) ions from aqueous solutions in a batch media was investigated. Various physico‐chemical parameters such as pH, initial metal ion concentration, temperature, and equilibrium contact time were also studied. Adsorption mechanism of Cu²⁺ ions onto magnetic polymeric adsorbents has been investigated using Langmuir, Freundlich, Sips and Redlich–Petersen isotherms. The results demonstrated that the PS@α‐Fe₂O₃ nanocomposite is an effective adsorbent for Cu²⁺ ions removal. The Sips adsorption isotherm model (R² > 0.99) was more in consistence with the adsorption isotherm data of Cu(II) ions compared to other models and the maximum adsorbed amount of copper was 34.25 mg/g. The adsorption kinetics well fitted to a pseudo second‐order kinetic model. The thermodynamic parameters (ΔH°, ΔS°, and ΔG°) were calculated from the temperature dependent sorption isotherms, and the results suggested that copper adsorption was a spontaneous and exothermic process. POLYM. ENG. SCI., 55:2735–2742, 2015. © 2015 Society of Plastics Engineers     

Polydopamine interface encapsulating graphene and immobilizing ultra-small,active Fe3O4 nanoparticles for organic dye adsorption

In this study, a combined process of bio-inspired modification and magnetic treatment is presented for the preparation of a polydopamine (Pdop)-modified graphene (Pdop-G)-based adsorbent which incorporates ultra-small, active Fe₃O₄ nanoparticles (with an average size of 6.5 nm). Not only can the nanoparticles impart superparamagnetism to the modified graphene adsorbent but also enhance the adsorption performance. The ultra-small size of Fe₃O₄ nanoparticles allows the exposure of a high proportion of low-coordinated sites such as corners and edges. Additional active sites can thus be provided to bind methylene blue molecules, in addition to the active Pdop-G surface with catechol and amine groups which induce hydrogen bonding, electrostatic attraction, and π-π stacking interactions. The Pdop interface wraps graphene and immobilizes Fe₃O₄, endowing the magnetic Pdop-G (MPG) with high adsorption capacity, easy recyclability, and excellent reusability for the organic pollutant removal. In stark contrast, the counterpart without the interfacial Pdop layer suffers from severe Fe₃O₄ aggregation, causing its adsorption performance inferior to that of MPG. The MPG-based adsorption obeys the pseudo-second-order kinetics, and the intraparticle diffusion model also indicates the complex adsorption pathway, including the external and intraparticle mass transfer. The Langmuir isotherm can better fit the experimental data than the Freundlich isotherm, with the theoretical maximum adsorption capacities estimated to be 131.6, 140.3, and 152.0 mg/g at 30, 40, and 50 °C, respectively. The adsorption is endothermic and spontaneous, along with an increase in the randomness at the solid-solution interface. The separation factor (R_L) reveals the favorable adsorption process with MPG. The superparamagnetism imparted via the Fe₃O₄ composition makes MPG easily recyclable. Furthermore, the removal rate can be maintained at about 90% after 5 runs of repeated usage of MPG. This study opens up a new avenue to the magnetization of adsorbents for enhancing adsorption performance in addition to imparting magnetism.     

Adsorption of Cu2+ and Ni2+ from Aqueous Solution by Arabinoxylan Hydrogel: Equilibrium,Kinetic, Competitive Adsorption

In this work, arabinoxylan-graft-acrylic acid (AX-g-AA) hydrogel was prepared and used as an adsorbent to remove and recover Cu²⁺ and Ni²⁺ from aqueous solutions. The influences of pH, ligand content on the adsorption capacity of the hydrogel, adsorption equilibrium, and kinetic were studied in detail. The competitive adsorption and recovery of heavy metal ions, regeneration and reusability of the hydrogel were present. Furthermore, the relationship between the physiochemical properties of the adsorbent and its adsorption performance was also studied. The results showed that a more expanded network favored the diffusion and adsorption of metal ions. Cu²⁺ and Ni²⁺ uptake by this hydrogel was pH and concentration dependent with the maximum loading of 330.1 mg/g for Cu²⁺ and 248.7 mg/g for Ni²⁺. The pseudo-second-order kinetics suggested that the ion exchange process was chemisorption-controlled. The Langmuir equation could well describe the isotherm data. Cu²⁺ and Ni²⁺ adsorbed on the hydrogel could be effectively recovered in a diluted HNO₃ solution (0.01 M) in 30 min. AX-g-AA hydrogel also exhibited highly efficient reusability, and thus could be used repeatedly.     

Modification and magnetization of MOF (HKUST-1) for the removal of Sr2+ from aqueous solutions. Equilibrium,kinetic and thermodynamic modeling studies

In this research, metal-organic framework MOF(HKUST-1) was synthesized, magnetized and modified by hexacyanoferrate in order to prepare an efficient adsorbent for the removal of Sr²⁺ from aqueous solutions. The synthesized adsorbent was characterized by X-ray diffraction (XRD), energy dispersive X-ray spectroscopy, thermal methods (TG-DTG[Themogravimetry- Derivative Theromogravimetry]), Fourier transform infrared (FTIR) spectroscopy, Brunauer–Emmett–Teller (BET) surface area and scanning electron microscopy (SEM). The non-magnetized (MOF/KNiFC[potassium nickel hexacyanoferrate]) and magnetized (MOF/Fe₃O₄/KNiFC) adsorbents were then employed for the removal of Sr²⁺ from aqueous solutions. The adsorption capacity of 110 and 90 mg.g^?1 was obtained, respectively, for MOF/KNiFC and MOF/Fe₃O₄/KNiFC. The adsorption process was kinetically fast and the equilibration was established within 45 min. The magnetic capability of the adsorbent examined by the vibrating sample magnetometer (VSM) technique indicated that the used adsorbent was capable of separating from the solution by applying an external magnetic field. The adsorbent showed good selectivity toward Sr²⁺ in the presence of Cs⁺, Na⁺, Mg²⁺, Ca²⁺ and Ba²⁺. The regenerated adsorbent retained more than 90% of its initial capacity. Different isotherm models including Langmuir, Freundlich, Tempkin, Sips and Redlich–Peterson were employed to examine the applicability of the isotherms to the experimental data. It was concluded that the data was best fitted to the Langmuir isotherm model. The thermodynamic parameters showed that the process was endothermic.     

One-Step Fabrication of Magnetic Carbon Nanocomposite as Adsorbent for Removal of Methylene Blue

Magnetic Fe₃O₄@C nanocomposites with well-defined core@shell structure were synthesized via a facile one-step solvothermal process using ferrocene as both iron and carbon resource in the presence of hydrogen peroxide (H₂O₂). The as-prepared Fe₃O₄@C nanocomposites were employed as adsorbent materials for removal of methylene blue (MB) from aqueous solution. Several experimental parameters, including contact time, acidity of the solution, and initial MB concentration were investigated. The result showed that the equilibrium uptake of MB was related to the MB initial concentration as well as acidity of the solution. The adsorption kinetics of MB was dominated by the pseudo-second order reaction model. Significantly, the synthesized Fe₃O₄@C nanocomposites could be easily isolated from the adsorption system after adsorbing MB and showed prominent reusability. All results indicated that the prepared Fe₃O₄@C composites had the potential to be used as adsorbents for the removal of dye pollutant from wastewater.     

Synthesis and characterization of magnetic beads containing aminated fibrous surfaces for removal of Reactive Green 19 dye: kinetics and thermodynamic parameters

BACKGROUND: Poly(HEMA‐co‐MMA) beads were prepared from 2‐hydroxyethyl‐methacrylate (HEMA) and methylmethacrylate (MMA) in the presence of FeCl₃. Thermal co‐precipitation of Fe(III) ions containing beads with Fe(II) ions was carried out under alkaline conditions. The magnetic beads were grafted with poly(glycidylmethacrylate; p(GMA)), and the epoxy groups of the grafted p(GMA) brushes were converted into amino groups by reaction with ammonia. RESULTS: The magnetic beads were characterized by surface area measurement, electron spin resonance (ESR), Mössbauer spectroscopy and scanning electron microscopy (SEM). The maximum adsorption of Reactive Green‐19 (RG‐19) dye on the p(GMA) grafted and amine modified magnetic beads was around pH 3.0. The adsorption capacity of magnetic beads was 84.6 mg dye g^?1. The effects of adsorbent dosage, ionic strength and temperature have also been reported. Batch kinetic sorption experiments showed that a pseudo‐second‐order rate kinetic model was applicable. CONCLUSION: The p(GMA) grafted and amine modified magnetic beads (adsorbent) were expected to have the advantage of mobility of the grafted chains in the removal of acidic dyes from aqueous solutions. The magnetic beads have potential as an adsorbent for removal of pollutants under various experimental conditions without significant reduction in their initial adsorption capacity. Copyright © 2011 Society of Chemical Industry     

Synthesis of Magnetic Fe3O4 Modified Graphene Nanocomposite and its Application on the Adsorption of some Dyes from Aqueous Solution

A novel magnetic Fe₃O₄ modified reduced graphene oxide nanocomposite (Fe₃O₄@SiO₂-rGO) was prepared by a covalent bonding method. The morphology and properties of the Fe₃O₄@SiO₂-rGO were characterized by transmission electron microscopy and X-ray diffraction. The prepared Fe₃O₄@SiO₂-rGO was tested as an efficient adsorbent for the removal of some dyes from aqueous solution for the first time. The performance of Fe₃O₄@SiO₂-rGO was evaluated using methylene blue and neutral red as model compounds. Experiments were carried out to investigate the adsorption kinetics and adsorption capacity of the adsorbent and the effect of the adsorbent dosage and sample solution pH on the removal of the dyes. Kinetic data were well fitted by pseudo second-order model. The Langmuir model and the Freundlich model were used to study the adsorption isotherms. The Fe₃O₄@SiO₂-rGO nanocomposite showed to be a highly efficient adsorbent with the advantage of separation convenience. The thermodynamic parameters indicated that the adsorption of the dyes onto the Fe₃O₄@SiO₂-rGO was a spontaneous process.     

Removal of heavy metal ions from aqueous solutions by radiation‐induced chitosan/(acrylamidoglycolic acid‐co‐acrylic acid) magnetic nanopolymer

An effective method was developed to isolate toxic heavy metal ions from the aqueous solution by the magnetic nanopolymers. The magnetic sorbent was prepared with radiation‐induced crosslinking polymerization of chitosan (CS), 2‐acrylamido‐glycolic acid (AMGA), and acrylic acid (AAc), which stabilized by magnetite (Fe₃O₄) as nanoparticles. The formation of magnetic nanoparticles (MNPs) into the hydrogel networks was confirmed by Fourier transform infrared spectroscopy, X‐ray diffraction, transmission electron microscopy, and Scanning electron microscopy, which revealed the formation of MNPs throughout the hydrogel networks. The swelling behavior of the hydrogels and magnetic ones was evaluated at different pH values. The adsorption activity for heavy metals such as Cu²⁺ and Co²⁺ by nonmagnetic and magnetic hydrogels, Fe₃O₄/CS/(AMGA‐co‐AAc), in terms of adsorption amount was studied. It was revealed that hydrogel networks with magnetic properties can effectively be used in the removal of heavy metal ions pollutants and provide advantageous over conventional ones. POLYM. ENG. SCI., 55:1441–1449, 2015. © 2015 Society of Plastics Engineers     

Influence of Fe3O4 nanoparticles decoration on dye adsorption and magnetic separation properties of Fe3O4/rGO nanocomposites

Magnetite (Fe₃O₄) nanoparticles were prepared by solvothermal method and its composites with reduced graphene oxide namely FG1, FG2, and FG3 (changing magnetite precursor loading 0.1, 0.5, and 1 respectively) were used as adsorbents for the removal of methyl violet (MV) dye. The structural and morphological results confirm that rGO sheets were decorated with Fe₃O₄ and it ensures the variation of active sites toward dye removal property. The maximum adsorption capacity obtained for FG2 was 196 mg/g. The adsorption isotherms and kinetics better fit Langmuir and pseudo-second-order kinetic model for FG1 and FG2. Increasing of Fe₃O₄ loading on rGO reduces the dye adsorption sites and too low Fe₃O₄ loading affects the magnetic separation. The optimal loading of Fe₃O₄ on rGO is important parameter for the adsorption process and fast separation of adsorbent.