Generalized analytical expressions for Tafel slope,reaction order and a.c. impedance for the hydrogen evolution reaction (HER): mechanism of HER on platinum in alkaline media

Following the generally accepted mechanism of the HER involving the initial proton discharge step to form the adsorbed hydrogen intermediate, which is desorbed either chemically or electrochemically, generalized expressions for the Tafel slope, reaction order and the a.c. impedance for the hydrogen evolution reaction are derived using the steady-state approach, taking into account the forward and backward rates of the three constituent paths and the lateral interactions between the chemisorbed intermediates. Limiting relationships for the Tafel slope and the reaction order, previously published, are deduced from these general equations as special cases. These relationships, used to decipher the mechanistic aspects by examining the kinetic data for the HER on platinum in alkaline media, showed that the experimental observations can be consistently rationalized by the discharge-electrochemical desorption mechanism, the rate of the discharge step being retarded on inactive platinum compared to the same on active platinum.Nomenclature C _d double-layer capacity (µF cm^–2) - E _rev reversible electrode potential (V) - F Faraday number (96 487 C mol^–1 ) - R gas constant - T temperature (K) - Y _f Faradaic admittance (^–1 cm^–2) - Y _t Total admittance (^–1 cm^–2) - Z _f Faradaic impedance ( cm²) - i _f total current density (A cm^–2) - i _nf nonfaradaic current density (A cm^–2) - j - k ₀ ¹ rate constant of the steps described in Equations 1 to 3 (mol cm^–2 s^–1 ) - j - qmax saturation charge (µC cm^–2) - Laplace transformed expressions for i, and E - _{1 3} symmetry factors for the Equations 1 and 3 - saturation value of adsorbed intermediates (mol cm^–2) - overpotential - coverage by adsorbed intermediates - angular frequency This paper is dedicated to Professor Brian E. Conway on the occasion of his 65th birthday, and in recognition of his outstanding contribution to electrochemistry.     

Electrolysis by intermittent potential

The application of an intermittent potential yields the maximum rate of electrolysis under non-d.c., mass transfer controlled conditions. A numerical solution was obtained to calculate the average current density under the intermittent potential condition. It is shown that the maximum rate of electrolysis for the intermittent potential case and consequently for all non-d.c. cases cannot exceed that under d.c. conditions.List of symbols c concentration of the reacting ion - c concentration of the reacting ion in the bulk - C dimensionless concentration defined in Equation 6 - D diffusion coefficient - (i _d.c.)₁ the d.c. limiting current density - ( _t)₁ average limiting current density under intermittent potential conditions - t time - z axial co-ordinate Greek _{n 1},_{n 3} coefficients of the series in Equations 1 - _{n 2} 12,13 and 16 - Nernst diffusion layer thickness - dimensionless axial co-ordinate defined in Equation 6 - ₁, _c constants defined in Equation 14 - _{n 2} constant defined in Equation 15 - dimensionless time defined in Equation 6 - ₁, _c dimensionless on-period and cycle period, respectively Deceased     

Identification of sex pheromones of two sibling species in dingy cutworm complex,Feltia jaculifera (GN.) (Lepidoptera: Noctuidae)

The sex pheromone components of the two sibling species of the dingy cutworm that occur on the prairies of western Canada were identified in abdomen-tip extracts from calling female moths. Three monounsaturated acetates, (Z)-7-dodecenyl acetate, (Z)-9-tetradecenyl acetate, and (Z)-11-hexadecenyl acetate, are common to both species in ratios of 100133 for species A and 0.30.5100 for species B. The most effective synthetic blends for the attraction of male moths in the field consisted of these three components in ratios of 1010 at 8.8g/lure for species A and 112000 at 500g/lure for species B. The addition of Z5-12Ac to either blend reduced the catches and the addition of Z7-12OH orZ11-16OH to the three-component blend reduced the catches of species B males. The species are morphologically indistinguishable, but the identity of the males attracted to the synthetic blends could be confirmed by their antennal responses to a test blend of the three components using a GC-EAD system. Both synthetic attractant blends are competitive with females and will be useful for studying the distribution, biology, and relative abundances of the two species.Contribution no. 3879005 of the Lethbridge Research Station.     

The effect of carbon black filling and cross-linking in stretched SBR networks: a 2H-NMR study

Summary The line splitting v in ²H-NMR spectra of deuterated benzene in stretched crosslinked SBR depended linearly on the classical stretch term ² – 1/ for samples with and without carbon black filling. The ratio LS = v/(² – 1/) was measured in dependence on the solvent fraction . The extrapolated value L of this ratio at =0 gave a linear dependence on the inverse molecular mass 1/M_c of inter-crosslink chains. This was expected according to a simple model of chain dynamics and offers a further NMR-method for M_c-determination even in filled networks. However, the slope of the L(1/M_c)-line increases with an addition of carbon black which indicates a higher molecular order. Three reasons for this could be discussed. However, one of them is preferable.     

Kinetics of copper electrodeposition in citrate electrolytes

The kinetics of copper electrocrystallization in citrate electrolytes (0.5M CuSO₄, 0.01 to 2M sodium citrate) and citrate ammonia electrolytes (up to pH 10.5) were investigated. The addition of citrate strongly inhibits the copper reduction. For citrate concentrations ranging from 0.6 to 0.8 M, the impedance plots exhibit two separate capacitive features. The low frequency loop has a characteristic frequency which depends mainly on the electrode rotation speed. Its size increases with increasing current density or citrate concentration and decreases with increasing electrode rotation speed. A reaction path is proposed to account for the main features of the reduction kinetics (polarization curves, current dependence of the current efficiency and impedance plots) observed in the range 0.5 to 0.8 M citrate concentrations. This involves the reduction of cupric complex species into a compound that can be either included as a whole into the deposit or decomplexed to produce the metal deposit. The resulting excess free complexing ions at the interface would adsorb and inhibit the reduction of complexed species. With a charge transfer reaction occurring in two steps coupled by the soluble Cu(I) intermediate which is able to diffuse into the solution, this model can also account for the low current efficiencies observed in citrate ammonia electrolytes and their dependencies upon the current density and electrode rotation speed.Nomenclature b, b ₁, b ₁ ^* Tafel coefficients (V^–1) - bulk concentration of complexed species (mol cm^–3) - (si*) concentration of intermediate C^* atx=0 (mol cm^–3) - C concentration of (Cu Cit H)^2– atx=0 (mol cm^–3) - C C variation due to E - C concentration of complexing agent (Cit)^3- at the distancex (mol cm^–3) - C _o concentrationC atx=0 (mol cm^–3) - C _o C _o variation due to E - Cv _s bulk concentrationC (mol cm^–3) - (Cit H), (Cu), (Compl) molecular weights (g) - C _dl double layer capacitance (F cm^–2) - D diffusion coefficient of (Cit)^3- (cm²s^–1) - D ₁ diffusion coefficient of C^* (cm²s^–1) - E electrode potential (V) - f ₁ frequency in Equation 25 (s^–1) - F Faraday's constant (96 500 A smol^–1) - i, i ₁, i ₁ ^* current densities (A cm^–2) - i i variation due to E - Im(Z) imaginary part ofZ - j - k ₁, k ₁ ^* , K₁, K ₁ ^* , K₂, K rate constants (cms^–1) - K rate constant (s^–1) - K ₃ rate constant (cm³ A^–1s^–1) - R _t transfer resistance (cm²) - R _p polarization resistance (cm²) - Re(Z) real part ofZ - t time (s) - x distance from the electrode (cm) - Z _f faradaic impedance (cm²) - Z electrode impedance (cm²) Greek symbols maximal surface concentration of complexing species (molcm^–2) - thickness of Nernst diffusion layer (cm) - , ₁, ₂ current efficiencies - angular frequency (rads^–1) - electrode rotation speed (revmin^–1) - =K ^–1(s) - _d diffusion time constant (s) - electrode coverage by adsorbed complexing species - (in0) electrode coverage due toC _s - variation due to E     

Studies concerning charged nickel hydroxide electrodes I. Measurement of reversible potentials

Reversible potentials (E _R) have been measured for nickel hydroxide/oxyhydroxide couples over a range of KOH concentrations from 0·01–10 M. It is shown that the couples derived from the parent- and-Ni(OH)₂ systems can be distinguished by the relative change in KOH level on oxidation and reduction. In the case of couples derived from the-class of materials a dependence of 0·470 moles of KOH per 2e change is found compared with 0·102 moles of KOH per 2e change for the-class of materials. Couples derived from the- and-Ni(OH)₂ systems can be encountered in a series of activated and de-activated forms having a range of formal potentialsE ₀ . Activated. and de-activated-Ni(OH)₂/-NiOOH couples are found to lie in the range 0·443–0·470 V whilst-Ni(OH)₂/-NiOOH couples lie in the range 0·392–0·440 V w.r.t. Hg/HgO/KOH. It is demonstrated for de-activated,-Ni(OH)₂/-NiOOH couples thatE _R is independent of the degree of oxidation of the nickel cation between states of charge of 25% and 70%. SimilarlyE _R is constant for states of charge between 12% and 60% for activated-Ni(OH)₂/-NiOOH couples. The constant potential regions are considered to be derived from heterogeneous equilibria between pairs of co-existing phases both containing nickel in upper and lower states of oxidation. Differences inE ₀ between the activated and de-activated couples are considered to be related to the degree of order/disorder in the crystal lattice.     

An investigation of some Schiff bases as corrosion inhibitors for austenitic chromium–nickel steel in H2SO4

The corrosion inhibition of austenitic chromium–nickel steel by two Schiff bases, N-(1-toluidine)salicylaldimine and N-(2-hydroxyphenyl)salicylaldimine, was investigated in sulphuric acid medium. The effect of concentration and temperature on inhibition properties was determined. It was found that when the concentrations of inhibitor were increased the inhibition efficiencies () and surface coverage () increased. Some thermodynamic parameters such as free energy of adsorption, G _ads, and enthalpy, H, were determined for the Schiff bases. Experimental results agree with the Temkin isotherm for N-(1-toluidine)salicylaldimine, but the Langmuir isotherm is more appropriate for N-(2-hydroxyphenyl)salicylaldimine.     

Critical solution point and chain dimension of branched-polystyrene solutions

Summary Critical solution point and chain dimension were measured for branched polystyrene(BPS) in solution as a function of molecular weight(M) and compared with those for linear polystyrene(LPS). The critical concentration _c of BPS was quite different from that of LPS at a fixed M, but the same at a fixed overlap-concentration ^*, i.e., plots of _c vs. ^* fall on a single straight line for both BPS and LPS (gf_c ^*). Reduced critical temperature _c defined by gt_c=(–T_c)/ [T_c: critical temperature, : the -temperature] was related to _c as _{c c} ² for BPS, whereas _{c c} for LPS.     

Effect of formulations and dispensers on attractiveness of virelure to the tobacco budworm

Formulations of virelure, the synthetic sex pheromone of the tobacco budworm,Heliothis virescens (F.), were developed, bioassayed in traps in field cages, and used in traps to survey populations in plant hosts. Virelure (10 mg) laminated between thin sheets of vinyl polymer plastic was attractive to male moths for 21 days, and attractiveness did not regress appreciably for the first 7 days. Another dispenser was an 8 × 30-mm cigarette filter encased in a glass shell vial. A mixture of 10 l (Z)-11-hexadecenal and 0.5 l (Z)-9-tetradecenal, the pheromone components, formulated with wheat germ oil andd-alpha tocopherol (91) in 0.5 ml CH₂Cl₂ (WGOE) was still attractive to males after 5 days. Cottonseed oil, polyethylene glycol 600 distearate (peg-600-d), and peg-6000-d also inhibited excessive vaporization and oxidation of virelure. Virelure (21.25 l) formulated on filters with WGOE and used as bait (replaced weekly) in survey traps caught 27,263 males in 1975; analysis of catches each day for 7-day periods showed that most males were caught within 3 days after baiting, and attractiveness regressed considerably during the last 3–4 days of each week. Four ratios of virelure components were tested as bait (20 mg) in saucer-type pheromone traps, and the 161 ratio caught significantly more male moths than ratios of 241, 321, or 401.Lepidoptera Noctuidae.In cooperation with the Texas Agricultural Experiment Station, Texas A & M University, College Station 77843.This paper reports the results of research only. Mention of a pesticide in this paper does not constitute a recommendation for use by the USDA nor does it imply registration under FIFRA as amended. Also, mention of a commercial or a proprietary product in this paper does not constitute an endorsement by the USDA.     

Studies concerning charged nickel hydroxide electrodes IV. Reversible potentials in LiOH,NaOH, RbOH and CsOH

The variation of reversible potential E_r with log a_moh and has been studied for several nickel hydroxide/oxyhydroxide couples in various alkali hydroxides. Both activated and deactivated -phase couples show only a small dependence ofE _r with log_moh (or where known) in LiOH, NaOH, RbOH and CsOH electrolytes. The change in MOH content on oxidation/reduction is found to be about 0.1 mol MOH per two-electron transfer and is the same as found previously in KOH. These results confirm that the bulk oxidized -phase lattice is devoid of alkali cation although a small quantity may be adsorbed by the surface. On the other hand both activated and deactivated /-phase couples show a marked dependence of 0.45 mol MOH per two-electron transfer in LiOH, NaOH and RbOH (at concentrations > 0.5 m), also in good agreement with earlier data for KOH. On the basis of these results a general stoichiometry can be inferred for the -phase, namely M_0.32NiO₂ · 0.7H₂O where M=Li⁺, Na⁺, K⁺ or Rb⁺. Measurements imply that the Cs⁺ ion or the Rb⁺ ion at low concentration (<0.5 m) do not enter the interlayer structure of the -phase. This behaviour is thought to be related to the low Rb-O and Cs-O bond strengths afforded by the -phase structure.     

Electrochemical behaviour of viologen-cyclodextrin inclusion complexes. The case of non-alkyl group substituted viologen

The electrochemical behavior of non-alkyl substituted viologen, 4,4-dibenzyl bipyridinium (BzV), 4,4-dicyanophenyl bipyridinium (CyV) and -,-,-cyclodextrin (, , -CD) was studied using cyclic voltammetry and a spectroelectrochemical method. It was found that BzV and Fe(CN) ₆ ^4– formed a charge-transfer (CT) complex with a ratio of 21 and the colour of the solution faded with the addition of an electrolyte. This behaviour is the same as in then-heptyl viologen and ferrocyanide system [1]. BzV, -CD and -CD formed an inclusion complex only in the reduced state, whilst BzV and -CD formed an inclusion complex in both the oxidized and the reduced state. An EC scheme in which a chemical reaction follows an electrochemical reaction was considered to predominate in the BzV and -, -CD systems, while a CE scheme in which a chemical reaction preceded an electrochemical reaction predominated in the BzV and -CD system. On the other hand, CyV was found to form an inclusion complex with -, -, -CD in both the oxidized and the reduced states. therefore a CE scheme was considered to predominate in the CyV--, -, -CD systems.     

Calorimetric,X-ray and infra-red investigations on poly(hexamethylene adipamide)

Summary In dependence on crystallization conditions three ranges with different crystal structure and heat of fusion were found by DSC,WAXS,and IR for unoriented PA 6.6 samples of densities between 1.10 and 1.17gcm^–3: Range I:_I triclinic, _c ^I =1.225 gcm^–3,H _M ^I = 235 Jg^–1. Range II:_II triclinic, _c ^II =1.165 gcm^–3, H _M ^II =185 Jg^–1. Range III:Continuous variation from _c ^I ,H _M ^I to _c ^II , H _M ^II . _a=1.095 gcm^–3 is independent of crystallization. conditions. The transition between _I and _II is probably due to changes of the chain conformation.     

Effect of resistivity on the corrosion mechanism of mild steel in sodium sulfate solutions

Electrochemical impedance spectroscopy (EIS) was used to study the corrosion behavior of mild steel samples immersed in 1, 0.1, 0.01 and 0.001% Na₂SO₄ aqueous solutions at room temperature in order to analyze the corrosion mechanism and obtain representative values of corrosion rates in environments with different resistivity. The EIS technique was used to measure corrosion current densities in 1 to 0.01% Na₂SO₄ solutions, and the measurement corresponding to 0.001% concentration gave a scattered Nyquist plot, whereas in the Bode representation a response associated with solution resistance was obtained. Other electrochemical techniques such as linear polarization resistance, LPR, Tafel extrapolation method and electrochemical noise (EN) were used in order to compare the results obtained by EIS. The charge-transfer resistance (R _ct) parameters obtained in the EIS technique agree well with the corresponding values of polarization resistance (R _p) values obtained by the LPR technique, whereas the electrochemical noise resistance (R _n) parameters obtained by the EN technique gave the highest values for all concentrations. These parameters generally tended to increase as the concentration of the solution decreased.     

The estimation of the residual capacity of sealed lead-acid cells using the impedance technique

The problem of estimating the residual usable energy of a lead-acid cell has been intensified by the introduction of fully sealed units. These rely on the recombination of gaseous oxygen produced during overcharge at the positive electrode with the active material at the negative electrode. This introduction has removed the possibility of electrolyte density measurements, third electrode measurements and restricted residual capacity assessments to the two cell terminals. A method for this process is described using a parameter based on a characteristic frequency. The parameter is also a useful measure of cell ageing.Nomenclature R _SOL Ohmic resistance of cell () - Charge-transfer resistance of positive and negative electrodes () - CL Double-layer capacitance of both positive and negative electrodes (F) - Warburg diffusion (S^–1/2) - C _EXT External series capacitor in analogue Fig. 5 (F) - R _EXT External resistor in parallel withC _EXT in the anologue circuit Fig. 5 () - IND Inductor in Fig. 5 representing the geometrical effects of the cell at high frequencies (Henries) - R _IND External resistor in parallel with IND in the analogue circuit Fig. 5 () - Roughness factor allowing for the porosity of both electrodes     

Studies on electrical conductivity of gamma irradiated polyaniline

Summary de electrical conductivity at surface of -irradiated polyaniline (PAn) has been studied. EPR spectroscopic results indicate that the variation of spin concentration is consistent with the increase of _de. Electrical conductivity (_de) versus temperature (T) characteristics of unirradiated and irradiated PAn were performed, which demonstrate that the unirradiated curve can fit to ln_deT₁, while the irradiated curve fit to ln_deT_1/4.     

Specific features of the phase transformations occurring during the sintering process of the beta-alumina based ceramics and their properties

Conclusions During the sintering process of beta-alumina obtained using the method of plasmochemical synthesis, the structural transformation occurs and it is accompanied by the separation of the excess Na₂O and the formation of an intergranular meltlike phase that is saturated with sodium and is characterized by high dielectric properties.The quantity of the meltlike phase and the magnitude of the /( + ) ratio determine the degree of stabilization (stability) and the final resistivity of the material and depend on the initial chemical composition and the heating rate maintained during the sintering process.It was shown that when the duration of residence of the material in the hot zone of the furnace is increased or when the specimens sintered maintaining high heating rates are subjected to additional heat treatment, one observes the occurrance of the reverse structural transformation that is characterized by an increase of the phase ratio /( + ) 1, a reduction in the quantity of the meltlike phase right up to its complete disappearance, and a decrease of the electrical resistivity of the material.In the materials having a large excess quantity of sodium oxide, the process of crystallization of the intergranular NaAlO₂ phase occurs simultaneously with the second phase transformation.The best ceramic and electrophysical parameters were obtained when sintering the material contained 7.9% Na₂O.Translated from Ogneupory, No. 3, pp. 13–18, March, 1990.     

The impedance of the alkaline zinc-mercuric oxide cell. I. Cell behaviour and interpretation of impedance spectra

The impedances of small (2400 mA h) alkaline Zn-HgO cells have been measured in the range 10 kHz-0.001 Hz at various states of charge from fully charged to fully discharged. The behaviour of the cell conforms to that expected for rate control by charge transfer at the zinc electrode and diffusion in solution. At low frequencies there is a relaxation in the diffusive circuit elements which ultimately results in a complete suppression of the capacitative component of the impedance at zero frequency. The low-frequency behaviour is analogous to convective diffusion and is due to the effective distance between the electrodes being small compared with the characteristic length (D/)^1/2. The magnitude of the charge transfer resistance is the best measure of the state of charge.Nomenclature a effective electrode separation - C _DL double-layer capacitance of cell - C _R capacitative component of cell impedance - C concentration difference - D percentage discharge in Equation 12 - D _i diffusion coefficient of speciesi - R ohmic resistance of cell - R _R resistive component of cell Faradaic impedance - Ui constant defined by Equation 10 - Z total cell impedance - Z _F cell Faradaic impedance - Z _F cell impedance modified for porosity effect - Z _x cell impedance of Faradaic component plus double layer - cell Warburg coefficient (slope ofR _R and 1/C _Rversus su}-1/2) - _C Warburg coefficient calculated fromC _r values - _i cell Warburg coefficient for speciesi - Warburg coefficient calculated fromR _R values - dihedral angle of tail of Sluyters plot (after coming-off high-frequency semicircle) - angular frequency     

Chemistry of Combustion Waves in Substances with a Complicated Structure of Reagent Molecules. 1. Structure of the Front of Rich Isopentane Flame

Results on the structure of the lowtemperature relaxation zone of the front of a laminar Bunsen flame of isoC₅H₁₂ (2methylbutane) under atmospheric pressure are presented. The flame of a premixed mixture isoC₅H₁₂ + O₂ + Ar with a fueltoair equivalence ratio of 1.7 is examined. The mass fluxes, total rates of reactions of matter consumption and expenditure, balance of substances, and profiles of bulk heatrelease rates are calculated on the basis of the experimental concentration and temperature profiles. The results obtained indicate that there is a vast region of lowtemperature conversion of isopentane in the flame front. It is found that only part of the products sampled by the microprobe from different points of the flame front results from transformations in the lowtemperature region, namely, oxygen, isopentane, water, carbon monoxide, propane, methane, and methanol. Ethylene, propylene, hydrogen dioxide, and formaldehyde are present in the lowtemperature zone in insignificant amounts; they are secondary products of conversion of methyl and propyl radicals. It is assumed that the observed feature is a result of the competing interaction of two mechanisms of fuelmixture conversion: selfcatalysis and thermal selfacceleration. Based on the previously suggested mechanism of oxidation pyrolysis by the scheme of intramolecular quadratic destruction, experimentally observed fragmentation of the isopentane molecule is demonstrated. In contrast to npentane, formation of methyl alcohol has been found in isopentane convection products.     

Silphinene Sesquiterpenes as Model Insect Antifeedants

Silphinene sesquiterpenes are established chrysomelid antifeedants. In this work, nine silphinene analogs, 11-acetoxy-5-angeloyloxysilphinen-3-one (1), 11-acetoxy-5-tigloyloxysilphinen-3-one (2), 11-acetoxy-5-iso- butyryloxysilphinen-3-one (3), 11-hydroxy-5-angeloyloxysilphinen-3-one (4), 11,5-dihydroxysilphinen-3-one (5), 11,5-diacetoxysilphinen-3-one (6), 5,11-diisobutyryloxysilphinen-3-one (7), silphinen-3,5,11-trione (8), and O-methyl-5-epicantabrenolic acid methyl ester (10), and a presilphiperfolane sesquiterpene (9) were tested against several divergent insect species, including the lepidopteran Spodoptera littoralis, the chrysomelid Leptinotarsa decemlineata, and five aphid species, and their antifeedant effects were compared with those of picrotoxinin, a GABA-antagonist, and thymol, an allosteric modulator for insect GABA receptors. All insects tested responded to at least one silphinene analog and/or GABA antagonist. Compound 3 and thymol were effective antifeedants against all species tested except S. littoralis, with varying potencies according to their feeding ecologies. The toxicity of these compounds was species-dependent and did not correlate with their antifeedant effect.     

Preparation of poly(alkylvinylether)s for nonlinear optical applications

Summary 3,5-Dimethoxy-4-(2-vinyloxyethoxy)-4-nitrostilbene 2 and 3,5-dimethoxy-4-(2-vinyloxyethoxy)-2,4-dinitrostilbene 5 were prepared by the reactions of 2-iodoethyl vinyl ether with 3,5-dimethoxy-4-hydroxy-4-dinitrostilbene 1 and 3,5-dimethoxy-4-hydroxy-2,4-dinitrostilbene 4, respectively. Monomers 2 and 5 were polymerized with cationic initiators to obtain polymers with the NLO-phores 3,5-dimethoxy-4-oxy-4-nitrostilbene and 3,5-dimethoxy-4-oxy-2,4-nitrostilbene in the side chain. The resulting polymer 3 and 6 were soluble in DMSO and DMF. The inherent viscosities of polymers were in the range of 0.28–0.33 dL/g in DMSO. Polymers 3 and 6 showed good thermal stabilities in their TGA thermograms, and the T_g values from DSC thermograms were in the range of 81–87°C.