多口三环CSRR微带低通滤波器的研究与设计

提出一种新型的多口三环CSRR结构,利用CSRR谐振器的单极点低通特性和环与微带线之间的耦合,构成低通滤波器.分析该结构的等效电路模式,指出谐振频率的计算公式.使用HFSS适当优化参数,可以得到性能良好的低通滤波器.其-3 dB截止频率8.76 GHz,通带内插入损耗小于0.3306 dB,通带内回波损耗小于-13.810 2 dB,衰减15 dB以上阻带带宽达到10.31 GHz.为了改善通带内的回波损耗,在微带线两侧加载并联开路枝节.其-3 dB截止频率8.385 GHz,通带内插入损耗小于0.174 7 dB,通带内回波损耗小于-19.707 7 dB,衰减15 dB以上阻带带宽达到10.7 GHz.     

基于阶梯阻抗发夹谐振器的小型低通滤波器

提出一种基于阶梯阻抗发夹谐振器的小型化微波低通滤波器,该滤波器仅由包含一节微带线的阶梯阻抗发夹谐振器构成。设计结果表明,滤波器3dB通带从DC(Direct Current)到2GHz,回波损耗优于10dB,且插入损耗从DC到1.7GHz时优于0.5dB,带外抑制从2.9～4GHz优于20dB。仿真结果和实验结果吻合良好。这种滤波器尺寸小,易制造,且具有陡峭的截止频率响应特性,可应用于许多微波系统中。     

一种超宽阻带微带低通滤波器的设计

基于传统阶跃阻抗滤波器,提出了一种易于实现的超宽阻带微带低通滤波器改进设计方案。低阻抗线部分采用扇形微带结构,在同等阶数下,该结构的滤波器与传统阶跃阻抗滤波器相比,具有更紧凑的电路结构以及更好的阻带特性。在滤波器末端并联开路短截线,使得阻带增加额外传输陷波点来抑制寄生通带。利用ADS和HFSS仿真软件对滤波器结构进行优化设计,并进行了实物的加工和测试。实测结果表明,通带3 dB 截止频率为2 GHz,通带内0-1.8 GHz 回波损耗大于20 dB,3-20 GHz 频率范围内的阻带抑制能达到25 dB 以上。     

基于阶梯阻抗的发夹结构低通滤波器设计

提出一种基于阶梯阻抗发夹谐振器的小型化微波低通滤波嚣,该滤波嚣仅由包含四节微带的阶梯阻抗发夹谐振器构成.设计结果表明,滤波器3dB通带从直流到2.8G,带内反射小于-20dB,带外抑制达到40dB.这种滤波器尺寸小,易制造,且具有陡峭的截止频率响应特性,可用于许多微波系统中.     

基于平衡技术的微带低通滤波器版图优化设计

微带线结构的不连续性,使反射损耗和插入损耗较大,影响滤波器性能。利用平衡法提升滤波器并联分支中较低的特性阻抗,达到降低微带线宽度的目的,从而均衡整个滤波器的宽度,使版图仿真优化。以一个5阶切比雪夫微带低通滤波器设计为例,仿真结果表明,滤波器通带内反射损耗从-9.566dB降低到-15.837dB,插入损耗从0.679dB降低到0.322dB,与直接采用Richards变换和Kuroda规则设计微带低通滤波器相比,该方法能缩短滤波器设计周期,获得满意的滤波器性能。     

A V-band planar narrow bandpass filter using a new type integrated waveguide transition

A surface mountable planar narrow bandpass filter is proposed and demonstrated at V-band. The filter is constructed using an integrated waveguide in an alumina substrate employing a novel microstrip line to waveguide transition. The insertion loss per one transition is less than 0.1 dB over 43 to 73 GHz. A fabricated three-pole Chebyshev filter exhibits an insertion loss of 3 dB with a 3.3% bandwidth at a center frequency of 62 GHz and the return loss is better than 15 dB in the passband.     

一种S波段小型宽带微带带通滤波器优化设计

基于并联短截线谐振器与联接线变换器构成的传统微带带通滤波结构,提出了一种工作在S波段的改进型宽带带通滤波器。以三阶结构为例,通过将两侧并联短截线进行弯折,形成耦合线结构;将中间并联短截线进行拆分,变为并联的短路线和开路线,实现了在通带性能基本不变的前提下,获得阻带可调控的传输零点,进而提高过渡带陡峭度。为了进一步抑制阻带,在滤波器两侧级联扇形微带低通滤波结构,改善阻带性能。利用ADS和HFSS仿真软件对滤波器结构进行仿真优化设计,并最终进行了实物加工和测试。实测结果表明,通带内2~4 GHz插入损耗小于0.7 dB,回波损耗大于17 dB,通带外4.6~6.5 GHz 阻带抑制达到20 dB 以上。     

Ultra-Wideband Bandpass Filters Using Quarter-Wave Short-Circuited Shunt Stubs and Quarter-Wave Series Transformers

This letter introduces a topology of a very wideband filter intended for the use in ultra-wideband 3.1-10.6 GHz applications. Basic filter configuration consists of quarter-wave short-circuited stubs and quarter-wave series transformers. To improve the out-of-band rejection, a low-pass filter is added across the symmetry plane. The proposed component is fabricated in a planar microstrip configuration; however, the topology can be easily adopted for other technologies including those based on surface micromachining. The measurements have shown an insertion loss below 0.86 dB, return loss above 14 dB, group-delay variation under 0.15 ns, and the third harmonic rejection better than 16 dB.     

A novel microstrip lowpass filter with sharp roll-off and ultra-wide stopband using SICMRC

This paper presents a novel microstrip lowpass filter with sharp roll-off and ultra-wide stopband using stepped-impedance resonator and bended transmission line structure. The filter includes stepped-impedance prototype filter and stepped-impedance compact microstrip resonator cells that are combined in one structure. The proposed filter has good specifications such as sharp roll-off, ultra-wide stopband and low insertion loss. The transition band is approximately 0.25 GHz from 1.75 to 2 GHz with corresponding attenuation levels of ?3 and ?40 dB. The attenuation level in the stopband is better than ?20 dB that is achieved from 1.94 to 23 GHz, and the insertion loss in the passband is less than 0.4 dB. The proposed filter is fabricated and measured, and the simulation and measurement results are found to be in good agreement with each other.     

具有良好选择性及带外抑制的小型低通滤波器

本文提出了一种具有良好选择性以及宽带带外抑制的小型低通滤波器结构。滤波器的每一级由一段微带线和交指电容构成。基于对每一级结构的分析,我们可以确定通带的范围。为了进一步提高带外的抑制性,对单级滤波器进行了周期性的级联。通过产生多个带外衰减极点来实现带外的宽带抑制。此滤波器3dB 截止频率3.67GHz,带内插损-0.9dB,带内回波损耗低于-13dB。通带到阻带的选择度为160dB/GHz。带外抑制从3.8GHz 到13.1GHz 低于-20dB。     

A novel cross-shape DGS applied to design ultra-wide stopband low-pass filters

This letter presents a novel low-pass filter with an ultra-wide stopband. The proposed filter is comprised of a new cross-shape defected ground structure (CSDGS). By using this structure, the filter not only supports conventional DGS performances with a sharp rejection, but also exhibits an ultra-wide stopband. For the deigned low-pass filter, an insertion loss of less than 2dB from dc to 3.5GHz and the rejection is better than 20dB from 4.3 to 15.8GHz. Predicted performances show widened and deepened stopband beyond the low passband. Furthermore, it is confirmed by measurement.     

一种高滚降宽阻带低通微带滤波器

普通的阶梯阻抗低通滤波器滚降系数一般低于80 dB/GHz,阻带抑制小于20 dB,使其应用受到较大限制;文中首先从理论上分析并设计了具有宽阻带优势的阶梯阻抗滤波器,然后引入扇形短截线结构提高滚降系数,设计了一款通带为0~6 GHz 的高滚降宽阻带的微带低通滤波器。利用ADS 和HFSS分别对滤波器进行了建模、仿真和优化;最后采用RO4003 板材加工并对实物进行了测试。测试结果显示,所设计的滤波器3 dB 截止频率为6.02 GHz,滚降系数为123 dB/ GHz,阻带6.24~20 GHz,阻带抑制大于30 dB。     

一种毫米波微带带通滤波器的设计

摘要：基于小反射理论,引入Klopfenstein阻抗渐变线对传统发夹型谐振器结构进行改进,设计了一种相对带宽为8%的结构紧凑型毫米波带通滤波器。采用S参数的多项式综合方法得到耦合矩阵电路模型,利用三维电磁场全波仿真软件HFSS拟合出耦合系数与谐振器间距、外部品质因数与抽头位置的关系曲线,进而提取出耦合矩阵对应滤波器的物理尺寸。实测结果表明：在28.8GHz-31.2GHz频带内,该滤波器的插损小于3.0dB,回波优于-17dB,带外抑制大于40dB@33GHz,测试结果与计算结果吻合较好。     

Design of high-temperature superconducting low-pass filter forbroad-band harmonic rejection

A new type of low-pass filter based on a coupled line and transmission line theory is proposed for suppressing harmonics and spurious frequency. The seventh-order coupled-line low-pass filter with strip line configuration was fabricated using a high-temperature superconducting (HTS) thin film on MgO(100) substrate. The seventh-order low-pass filter has five attenuation poles in the stop band. Its cutoff frequency is 1 GHz with a 0.01-dB ripple level. The fabricated filter exhibits a characteristic stop band in the range from 1 to 7 GHz. A measured insertion loss at the pass-band of the HTS low-pass filter is 0.2 dB at 77 K, while the maximum return loss is 17.1 dB. These results match well with those obtained by the EM simulation. The new low-pass filter structure is shown to have attractive properties such as compact size, wide stop band range, and low insertion loss     

基于DGS微带低通滤波器的改进设计

按照传统方法设计了一个截止频率为3 GHz,通带波纹不大于0.5 dB。利用缺陷地单元（DGS）的带阻特性对传统设计方法进行了改进,改进后的滤波器完全满足设计要求,并使滤波器尺寸大幅减小。     

Ultra-wideband bandpass filter using CPW-to-microstrip coupling structure

A novel ultra-wideband bandpass filter based on a back-to-back microstrip-CPW transition structure is presented. The filter is composed of two microstrip-CPW transitions and a section of microstrip line used as a multiple-mode resonator. The filter has been investigated numerically and experimentally. Both simulated and measured results show that the filter has a good performance, including a small insertion loss, a group delay variation of less than 0.2 ns, stopband of up to 16.0 GHz at high frequencies, and an out-of-band rejection level of below -20.0 dB.     

Wide-stopband microstrip low-pass filter using modified semi-circle patch resonator

In this article, a compact microstrip low-pass filter with elliptic-function response is proposed. To achieve wide stopband, modified semi-circle patch resonator in series with semi-circle stepped impedance resonator is used. The proposed structure achieves a wide stopband and a high selectivity within a small circuit area. The proposed filter has 3-dB cutoff frequency at 1.71?GHz and 20?dB rejection at 2.1?GHz. The stopband with the attenuation level better than ?18.7?dB is from 2.08 up to 16?GHz, and consequently we have reached the high and wide rejection in stopband as well as compact size. The structure is simulated, fabricated and measured. The measured results are in good agreement with the simulated results.     

Design of low-pass filter with 3-interations Koch fractal Pi-shaped DGS

A novel asymmetrical Pi-shaped defected ground structure (DGS) with 3-interations Koch fractal curves is proposed to design a microstrip low-pass filter (LPF) with ultra-wide stop-band (SB). The proposed LPFs with a single resonator and two cascaded resonators are both designed, simulated, manufactured and measured. Simulation and experiment results demonstrate that the designed LPF has a very sharp transition band (TB) and an ultra-wide SB performance compared with the existed similar symmetrical and asymmetrical DGS. The proposed LPF with two cascaded resonators is with a compact size of 36.8 mm×24.0 mm, a very low insertion loss of less than 0.7 dB under 1.9 GHz, and a wide SB from 2.2 GHz to 8 GHz with rejection of larger than 30 dB.     

Compact Elliptic-Function Low-Pass Filter Using Defected Ground Structure

A novel elliptic-function low-pass filter (LPF) is presented, which consists of a dumb-bell-shaped defected ground structure (DB-DGS), a spiral-shaped defected ground structure (SP-DGS) and a broadened microstrip line. The DB-DGS provides the required wideband attenuation in stopband, while the SP-DGS provides steep transition from passband to stopband. A 2.4 GHz five-pole LPF is developed and experimental results show that it has a sharp cutoff frequency response. The measured passband insertion-loss is below 0.3 dB, and the rejection band over 20 dB is from 2.95 to 8.25 GHz.      

一种IPD吸收式低通滤波器的设计

为解决反射信号损害系统性能的问题,提出了一种具有高带外抑制和高带外吸收的小型化吸收式低通滤波器。该滤波器通过高通通路和低通通路实现了吸收式低通滤波器;通过抑制增益支路实现了高带外抑制。利用ADS和HFSS仿真软件对滤波器结构进行优化设计,并进行了实物的加工和测试。实测结果表明:该滤波器的3 dB截止频率为4 GHz,其带内最小插入损耗0.88 dB,通带内DC到3.5 GHz的回波损耗大于20 dB,阻带回波损耗大于10 dB,10.5 GHz处的阻带抑制大于45dB,从8 GHz到30 GHz的带外抑制大于33 dB,实测结果与仿真结果有较好的吻合。该滤波器尺寸仅为1220μm×650μm×87.71μm,相比传统PCB、LTCC工艺的滤波器,体积大大缩小,符合现代射频与微波系统小型化的发展趋势。