A /spl Sigma/-/spl Delta/ fractional-N frequency synthesizer using a wide-band integrated VCO and a fast AFC technique for GSM/GPRS/WCDMA applications

A fractional-N frequency synthesizer (FNFS) in a 0.5-/spl mu/m SiGe BiCMOS technology is implemented. In order to operate in a wide-band frequency range, a switched-capacitors bank LC tank voltage-controlled oscillator (VCO) and an adaptive frequency calibration (AFC) technique are used. The measured VCO tuning range is as wide as 600 MHz (40%) from 1.15 to 1.75 GHz with a tuning sensitivity from 5.2 to 17.5 MHz/V. A 3-bit fourth-order /spl Sigma/-/spl Delta/ modulator is used to reduce out-of-band phase noise and to meet a frequency resolution of less than 3 Hz as well as agile switching time. The experimental results show -80 dBc/Hz in-band phase noise within the loop bandwidth of 25 kHz and -129 dBc/Hz out-of-band phase noise at 400-kHz offset frequency. The fractional spurious is less than -70 dBc/Hz at 300-kHz offset frequency and the reference spur is -75 dBc/Hz. The lock time is less than 150 /spl mu/s. The proposed synthesizer consumes 19.5 mA from a single 2.8-V supply voltage and meets the requirements of GSM/GPRS/WCDMA applications.     

A 0.8-V 4.9-mW 1.2-GHz CMOS Fractional-N Frequency Synthesizer for UHF RFID Readers

A fully integrated CMOS frequency synthesizer for UHF RFID reader is implemented in a 0.18-$mu$m CMOS technology. Due to the large self-interference and the backscatter scheme of the passive tags, reader synthesizer's phase noise requirement is stringent to minimize the sensitivity degradation of the reader RX. The modified transformer feedback voltage-controlled oscillator (VCO) exhibits enhanced tank impedance and even harmonic noise filtering to achieve low phase noise. A third-order 2-bit single-loop $Sigma Delta$ modulator is optimized for the proposed synthesizer in terms of phase noise and power. The synthesizer provides a frequency resolution of 25-kHz with a tuning range from 1.03 GHz to 1.4 GHz . Phase noise of ${-}$70 dBc/Hz inband, ${-}$104 dBc/Hz at 200-kHz offset and ${-}$ 121 dBc/Hz at 1-MHz offset with a reference spur of ${-}$84 dBc are measured at a center frequency of 1.17 GHz and a loop bandwidth of 35 kHz. Power dissipation is 4.92 mW from a 0.8 V supply.      

Comparison frequency doubling and charge pump matching techniques for dual-band /spl Delta//spl Sigma/ fractional-N frequency synthesizer

The frequency synthesizer with two LC-VCOs is fully integrated in a 0.35-/spl mu/m CMOS technology. In supporting dual bands, all building blocks except VCOs are shared. A current compensation scheme using a replica charge pump improves the linearity of the frequency synthesizer and, thus, suppresses spurious tones. To reduce the quantization noise from a /spl Delta//spl Sigma/ modulator and the noise from the building blocks except the VCO, the proposed architecture uses a frequency doubler with a noise-insensitive duty-cycle correction circuit (DCC) in the reference clock path. Power consumption is 37.8 mW with a 2.7-V supply. The proposed frequency synthesizer supports 10-kHz channel spacing with the measured phase noise of -114 dBc/Hz and -141 dBc/Hz at 100-kHz and 1.25-MHz offsets, respectively, in the PCS band. The fractional spurious tone at 10-kHz offset is under -54 dBc.     

A fully integrated CMOS frequency synthesizer with charge-averagingcharge pump and dual-path loop filter for PCS- and cellular-CDMAwireless systems

A fully integrated CMOS frequency synthesizer for PCS- and cellular-CDMA systems is integrated in a 0.35-μm CMOS technology. The proposed charge-averaging charge pump scheme suppresses fractional spurs to the level of noise, and the improved architecture of the dual-path loop filter makes it possible to implement a large time constant on a chip. With current-feedback bias and coarse tuning, a voltage-controlled oscillator (VCO) enables constant power and low gain of the VCO. Power dissipation is 60 mW with a 3.0-V supply. The proposed frequency synthesizer provides 10-kHz channel spacing with phase noise of -121 dBc/Hz in the PCS band and -127 dBc/Hz in the cellular band, both at 1-MHz offset frequency     

使用三位三阶Δ∑调制器的集成1GHz小数频率合成器

本文实现了一个采用三位三阶Δ∑调制器的高频谱纯度集成小数频率合成器.该频率合成器采用了模拟调谐和数字调谐组合技术来提高相位噪声性能,优化的电源组合可以避免各个模块之间的相互干扰,并且提高鉴频鉴相器的线性度和提高振荡器的调谐范围.通过采用尾电流源滤波技术和减小振荡器的调谐系数,在片压控振荡器具有很低的相位噪声,而通过采用开关电容阵列,该压控振荡器达到了大约100MHz的调谐范围,该开关电容阵列由在片数字调谐系统进行控制.该频率合成器已经采用0.18μm CMOS工艺实现,仿真结果表明,该频率频率合成器的环路带宽约为14kHz,最大带内相位噪声约为-106dBc/Hz;在偏离载波频率100kHz处的相位噪声小于-120dBc/Hz,具有很高的频谱纯度.该频率合成器还具有很快的反应速度,其锁定时间约为160μs.     

一种9.8-mW 1.2-GHz CMOS 低噪声正交输出频率综合器

实现了一种基于标准0.18µm CMOS工艺的应用于北斗导航射频接收机的1.2GHz频率综合器。在频率综合器中采用了一种基于分布式偏置技术实现的低噪声高线性LC压控振荡器和一种基于源极耦合逻辑的高速低开关噪声正交输出二分频器,集成了基于与非触发器结构的高速8/9双模预分频器、无死区效应的延迟可编程的鉴频鉴相器和电流可编程的电荷泵。该频率综合器的输出频率范围从1.05到1.30GHz。当输出频率为1.21GHz 时,在100-kHz和1-MHz的频偏处相位噪声分别为-98.53dBc/Hz和-121.92dBc/Hz。工作电压为1.8V时,不包括输出Buffer的核心电路功耗为9.8mW。北斗射频接收机整体芯片面积为2.41.6 mm2。     

A 900-MHz 2.5-mA CMOS frequency synthesizer with an automatic SCtuning loop

A 900-MHz phase-locked loop frequency synthesizer implemented in a 0.6-μm CMOS technology is developed for the wireless integrated network sensors applications. It incorporates an automatic switched-capacitor (SC) discrete-tuning loop to extend the overall frequency tuning range to 20%, while the VCO gain (K_VCO) resulting from the CMOS varactor continuous-tuning is kept low at only 20 MHz/V in order to improve the reference spurs and noise performance. This frequency synthesizer achieves a phase noise of -102 dBc/Hz at 100 kHz offset frequency and reference spurs below -55 dBc. The synthesizer, including an on-chip VCO, dissipates only 2.5 mA from a 3-V supply     

A high-speed multimodulus HBT prescaler for frequency synthesizerapplications

A high-speed variable modulus prescaler that divides the input clock frequency by 128 up to 255 with unit step increment has been implemented with heterojunction bipolar transistor (HBT) technology. A maximum operating frequency of 9.72 GHz with power consumption of 650 mW has been measured. The high-speed performance is attributed to the circuit design, which minimizes the critical path delay, and the intrinsic high-speed characteristics of HBT technology. The phase noise of the prescaler is important for frequency synthesizer applications. With 6.24-GHz input frequency, the phase noise was -110 dBc/Hz at 100-Hz offset frequency and -120 dBc at 1-kHz offset frequency. The noise floor decreases as the input frequency decreases. Phase noises of -125 dBc/Hz at 100-Hz offset and -135 dBc/Hz at 1-kHz offset were obtained for a 1.2-GHz input frequency     

A 2 V 1.8 GHz fully integrated CMOS dual-loop frequency synthesizer

A 2 V 1.8 GHz fully integrated CMOS dual-loop frequency synthesizer is designed in a standard 0.5 /spl mu/m digital CMOS process for wireless communication. The voltage-controlled oscillator (VCO) required for the low-frequency loop is designed using a ring-type VCO and achieves a tuning range of 89% from 356 to 931 MHz and a phase noise of -109.2 dBc/Hz at 600 kHz offset from 856 MHz. With an active chip area of 2000/spl times/1000 /spl mu/m/sup 2/ and at a 2 V supply voltage, the whole synthesizer achieves a tuning range from 1.8492 to 1.8698 GHz in 200 kHz steps with a measured phase noise of -112 dBc/Hz at 600 kHz offset from 1.86 GHz. The measured settling time is 128 /spl mu/s and the total power consumption is 95 mW.     

A 2.4 GHz high-linearity low-phase-noise CMOS LC-VCO based on capacitance compensation

A 2.4 GHz high-linearity low-phase-noise cross-coupled CMOS LC voltage-controlled oscillator(VCO) is implemented in standard 0.18-μm CMOS technology.An equalization structure for tuning sensitivity base on the three-stage distributed biased switched-varactor bank and the differential switched-capacitor bank is adopted to reduce the variations of the VCO gain,achieve high linearity,and optimize the phase-noise performance.Compared to the conventional VCO,the proposed VCO has more constant gain over the en...     

A 4.3-GHz VCO with 2-GHz tuning range and low phase noise

A voltage-controlled oscillator (VCO) based on double cross-coupled multivibrator structure with a center frequency of 4.3 GHz and a tuning range of 2 GHz has been designed and implemented in standard 0.35 μm BiCMOS technology. The measured phase noise is 113 dBc/Hz at 600-kHz offset frequency from the carrier. The VCO draws 14.6 mA from the 2.5-V supply     

An integrated 8-12 GHz fractional-N frequency synthesizer in SiGe BiCMOS for satellite communications

We present an integrated fractional-N low-noise frequency synthesizer for satellite applications. By using two integrated VCOs and combining digital and analog tuning techniques, a PLL lock range from 8 to 12 GHz is achieved. Due to a small VCO fine tuning gain and optimized charge pump output biasing, the phase noise is low and almost constant over the tuning range. All 16 sub-bands show a tuning range above 900 MHz each, allowing temperature compensation without sub-band switching. This makes the synthesizer robust against variations of the device parameters with process, supply voltage, temperature and aging. The measured phase noise is ?87 dBc/Hz and ?106 dBc/Hz at 10 kHz and 1 MHz offset, respectively. In integer-N mode, phase noise values down to ?98 dBc/Hz at 10 kHz and ?111 dBc/Hz at 1 MHz offset, respectively, were measured.     

A study of digital and analog automatic-amplitude control circuitry for voltage-controlled oscillators

This paper presents both analog and digital automatic-amplitude control techniques for voltage-controlled oscillators (VCOs). These feedback mechanisms help to keep the VCOs at an optimum amplitude over temperature, process, and voltage variations. The VCOs were fabricated in a 50-GHz SiGe BiCMOS process. They use MOS varactors and achieve a 600-MHz tuning range in the 2-GHz band. The phase noise of the VCO with analog control was measured to be -99 dBc/Hz at 100-kHz offset from the carrier. The digital loop allows for a more optimized VCO core that achieves a phase noise of -108.5 dBc/Hz at 100-kHz offset in a low-gain mode. Techniques for suppressing the phase noise in regions of high gain are also presented. The VCOs draw between 4 and 8 mA from a 3.3-V supply.     

具有自校准压控振荡器和精确自动频率校准算法的低噪声频率合成器

A low noise phase locked loop （PLL） frequency synthesizer implemented in 65 nm CMOS technology is introduced. A VCO noise reduction method suited for short channel design is proposed to minimize PLL output phase noise. A self-calibrated voltage controlled oscillator is proposed in cooperation with the automatic frequency calibration circuit, whose accurate binary search algorithm helps reduce the VCO tuning curve coverage, which reduces the VCO noise contribution at PLL output phase noise. A low noise, charge pump is also introduced to extend the tuning voltage range of the proposed VCO, which further reduces its phase noise contribution. The frequency synthesizer generates 9.75-11.5 GHz high frequency wide band local oscillator （LO） carriers. Tested 11.5 GHz LO bears a phase noise of-104 dBc/Hz at 1 MHz frequency offset. The total power dissipation of the proposed frequency synthesizer is 48 mW. The area of the proposed frequency synthesizer is 0.3 mm^2, including bias circuits and buffers.     

A 1-V 9.7-mW CMOS Frequency Synthesizer for IEEE 802.11a Transceivers

A 1-V CMOS frequency synthesizer is proposed for wireless local area network 802.11a transceivers using a novel transformer-feedback voltage-controlled oscillator (VCO) for low voltage and a stacked frequency divider for low power. Implemented in a 0.18-mum CMOS process and operated at 1-V supply, the VCO measures a phase noise of -140.5 dBc at an offset of 20 MHz with a center frequency of 4.26 GHz and a power consumption of 5.17 mW. Its tuning range is as wide as 920 MHz (23%). By integrating the VCO into a frequency synthesizer, a phase noise of -140.1 dBc/Hz at an offset of 20 MHz is measured at a center frequency of 4.26 GHz. Its output frequency can be changed from 4.112 to 4.352 GHz by switching the 3-bit modulus of the programmable divider. The synthesizer consumes only 9.7 mW and occupies a chip area of 1.28 mm².     

A wideband frequency synthesizer for a receiver application at multiple frequencies

An integer-N frequency synthesizer for a receiver application at multiple frequencies was implemented in 0.18 μm IP6M CMOS technology. The synthesizer generates 2.57 GHz, 2.52 GHz, 2.4 GHz and 2.25 GHz local signals for the receiver. A wide-range voltage-controlled oscillator (VCO) based on a reconfigurable LC tank with a binary-weighted switched capacitor array and a switched inductor array is employed to cover the desired frequencies with a sufficient margin. The measured tuning range of the VCO is from 1.76 to 2.59 GHz. From the carriers of 2.57 GHz,2.52 GHz, 2.4 GHz and 2.25 GHz, the measured phase noises are -122.13 dBc/Hz, -122.19 dBc/Hz, -121.8 dBc/Hz and -121.05 dBc/Hz, at 1 MHz offset, respectively. Their in-band phase noises are -80.09 dBc/Hz, -80.29 dBe/Hz,-83.05 dBc/Hz and -86.38 dBc/Hz, respectively. The frequency synthesizer including buffers consumes a total power of 70 Mw from a 2 V power supply. The chip size is 1.5 × 1 mm~2.     

A 9.8-mW 1.2-GHz CMOS frequency synthesizer with a low phase-noise LC-VCO and an I/Q frequency divider

A 1.2 GHz frequency synthesizer integrated in a RF receiver for Beidou navigation is implemented in standard 0.18μm CMOS technology.A distributed biased varactor LC voltage-controlled oscillator is employed to achieve low tuning sensitivity and optimized phase noise performance.A high-speed and low-switching-noise divider-by-2 circuit based on a source-coupled logic structure is adopted to generate a quadrature(I/Q) local oscillating signal.A high-speed 8/9 dual-modulus prescaler(DMP),a programmable-delay phase frequency detector without dead-zone problem,and a programmable-current charge pump are also integrated into the frequency synthesizer. The frequency synthesizer demonstrates an output frequency from 1.05 to 1.30 GHz,and the phase noise is-98.53 dBc/Hz at 100-kHz offset and -121.92 dBc/Hz at 1-MHz offset from the carrier frequency of 1.21 GHz. The power dissipation of the core circuits without the output buffer is 9.8 mW from a 1.8 V power supply.The total area of the receiver is 2.4×1.6 mm~2.     

A 2-V 900-MHz monolithic CMOS dual-loop frequency synthesizer forGSM receivers

A 900-MHz monolithic CMOS dual-loop frequency synthesizer suitable for GSM receivers is presented. Implemented in a 0.50-μm CMOS technology and at a 2-V supply voltage, the dual-loop frequency synthesizer occupies a chip area of 2.64 mm² and consumes a low power of 34 mW. The measured phase noise of the synthesizer is -121.8 dBc/Hz at 600-kHz offset, and the measured spurious levels are -79.5 and -82.0 dBc at 1.6 and 11.3 MHz offset, respectively     

A fully integrated low-noise 1-GHz frequency synthesizer design formobile communication application

This paper describes a fully monolithic phase-locked loop (PLL) frequency synthesizer circuit implemented in a standard 0.8-μm CMOS technology. To be immune to noise, all the circuits in the synthesizer use differential schemes with the digital parts designed by static logic. The experimental voltage controlled oscillator (VCO) has a center frequency of 800 MHz and a tuning range of ±25%. The measured frequency synthesizer performance has a frequency range from 700 MHz to 1 GHz with -80 dBc/Hz phase noise at a 100 kHz carrier offset. With an active area of 0.34 mm², the test chip consumes 125 mW at maximum frequency from a 5 V supply. The only external components are the supply decoupling capacitors and a passive filter     

一种UHF频段小数分频频率综合器设计与实现

基于130 nm CMOS工艺设计了一款特高频(UHF)频段的锁相环型小数分频频率综合器.电感电容式压控振荡器(LC VCO)片外调谐电感总值为2 nH时,其输出频率范围为1.06～1.24 GHz,调节调谐电感拓宽了频率输出范围,并利用开关电容阵列减小了压控振荡器的增益.使用电荷泵补偿电流优化了频率综合器的线性度与带内相位噪声.此外对电荷泵进行适当改进,确保了环路的稳定.测试结果表明,通过调节电荷泵补偿电流,频率综合器的带内相位噪声可优化3 dB以上,中心频率为1.12 GHz时,在1 kHz频偏处的带内相位噪声和1 MHz频偏处的带外相位噪声分别为-92.3和-120.9 dBc/Hz.最小频率分辨率为3 Hz,功耗为19.2 mW.