Forensic Study of Warranty Project on US82

This forensic study is unique in that it involves a pavement warranty specification. Extensive field and laboratory testing was conducted to determine the cause(s) of longitudinal cracks observed on the surface. Four trenches were cut and removed to allow more testing on top of each pavement layer. The tests found that the stiffness of the foamed asphalt base is higher than that of a typical flexible base. However, the subgrade modulus is low compared with the average subgrade modulus in Texas. Water seeped into two trenches (dug into the road where there were surface cracks) within 20 min of digging. No water was observed in the other two trenches, where there were no surface cracks. The two trenches with surface cracks have lower base density and higher base moisture content than the two with no surface cracks. Based on observations of the trenching and coring operations, the same surface cracks have been detected in the base layer. Cracks up to 150 mm into the base layer have been observed. Although cracks have been observed in the base (and they can be related to lower stiffness and higher falling weight deflectometer deflections), it is difficult to determine if the cause of surface cracks is due to the base layer alone. It is difficult to prove if the layer is responsible for the failure, except by properties listed in the specification. One faulty pavement layer can easily cause the failure of other layers. For warranty purposes, layer-specific failure criteria should be clearly outlined. The base did not meet the gradation specification. The field material was substantially finer than specified. While some specifications may have been violated, there is little evidence to show that the cause of the longitudinal cracking is primarily related to the foamed-asphalt-stabilized base.     

Use of an Infrared Joint Heater to Improve Longitudinal Joint Performance in Hot Mix Asphalt Pavements

Longitudinal joint cracking is one of the most prevalent forms of distress in asphalt concrete pavements. The joint area does not achieve the same density as the mat due to an unconfined edge on the initial pass and a cold joint during the second pass. The lower density allows water to penetrate and the material cracks, usually within one?year of construction. There are many techniques for constructing longitudinal joints, one being to preheat the joint prior to paving the second lane. This paper describes a field study conducted in New Hampshire using an infrared joint heater. Thermocouples were embedded in the pavement to determine the extent of heat penetration from the infrared heaters. Cores were taken along the joint and in the travel lanes for both the control and test sections. Density and strength measurements were taken on the cores. Permeability measurements along the control and test joints were performed. A cracking survey performed one?year after construction showed that the section of pavement where the infrared heater was used had significantly less cracking than the control section.     

Performance of Transverse Cracking in Jointed Concrete Pavements

Environmental effects and repetitive traffic applications can lead to the development of transverse cracks in jointed concrete pavements. Maintaining adequate aggregate interlock load transfer across these cracks is essential to preserving the functional and structural integrity of these pavements. The objectives of this study were to determine the design parameters that significantly affect transverse cracking and to demonstrate methods available for evaluating cracked pavements. Field data collected from in-service jointed concrete pavements located throughout southern Michigan were used to accomplish these objectives. Joint spacing, coarse aggregate type, shoulder type, and pavement temperature were found to have significant effects on transverse crack development and∕or performance. The surface texture of crack faces was assessed using a promising new test method called volumetric surface texture testing. Volumetric surface texture results provided an indication of the aggregate interlock potential of pavements containing various aggregate types. Three performance parameters capable of mechanistically characterizing crack performance were discussed. A relatively simple procedure was described for determining these parameters and evaluating crack conditions. Field data were also used to demonstrate and validate a voids' analysis procedure. This procedure estimates the potential for loss of support near cracks and joints, thus allowing for proper rehabilitation actions to be taken prior to the manifestation of additional distresses.     

Sudden Failure of a Heavily Loaded Container Pavement

The case history of a sudden and unexpected failure in a pavement designed for 82?Mg axle loads at Port Botany in Sydney, Australia has been prepared using data derived from investigation of the failure. Failure of the pavement, comprised of an asphaltic concrete surface, unbound granular fine crushed rock base, crushed sandstone subbase, and sandy subgrade, and designed using the rational method—CIRCLY, occurred within days of being put into service. The failure resulted from a 20–30% increase in base course saturation levels following compaction that led to partial liquefaction under repeated heavy loading. There was a general failure throughout the storage area where trafficking was most intense and the pavement remained intact in lightly trafficked areas. The intact areas recovered over time without intervention through a moisture equilibration process as evidenced by an increase in measured pavement stiffness and loss of moisture within the pavement profile.     

Field and Lab Investigations of Prematurely Cracking Pavements

A forensic study was conducted to identify the cause of the premature cracking on three recently completed projects that were built with the same design. Nondestructive [ground penetration radar, falling weight deflectometer (FWD), GeoGauge, and Portable FWD], nuclear density gauge, dynamic cone penetration, and extensive laboratory tests were performed. It was found that the initial stiffness of the treated base was found to be excessively high by FWD backcalculation. Some sections of the backcalculated base moduli were over 20.7?GPa. This indicates that the layer is excessively brittle for a base material, similar to lean concrete. Six specimens (that were made without a mellowing period) exhibited cracks. There was no cracking for six specimens that had two days of mellowing. It was concluded that the culprit of the transverse cracking in the main lanes was the shrinkage of lime treated base layers. The longitudinal cracks are related to the edge drying and the transverse cracks are related to the insufficient mellowing period. Based on the findings of this study, the District implemented a 2-day mellowing period for Quicklime treated caliche base. Three newly constructed pavements (age 8, 5, and 2?months) were surveyed. No cracking can be observed so far, and the District thinks the cracking problem has been mitigated by the 2-day mellowing period. Without the mellowing period, cracking had normally occurred 1?to?2?months after construction..     

Performance of Dowel Bar Retrofit Projects in Texas

In Texas, many miles of plain jointed concrete pavement (JCP) were constructed without proper load transfer devices such as dowels. After a number of years of service, some JCP sections without dowels showed distresses in the form of faulting at transverse joints. Some of the sections were designed in accordance with the AASHTO 1986 Guide, which required 50–75?mm thicker slabs in exchange for not using dowels. This pavement design did not work, with faulting at transverse joints that cause poor ride. Dowel bar retrofit (DBR) was performed on four projects to restore the pavement condition. Overall, DBR restored load transfer efficiency and resulted in improvement of ride quality. Even where the subbase stiffness is 5–10 times less than the minimum value required for proper performance of JCPs, properly installed DBR effectively restored pavement condition with minimum faulting after decades of service. Therefore, it indicated that DBR is able to minimize the faulting even where there is poor base/subgrade support. This is significant in that there are no effective and practical methods to improve subbase conditions in existing concrete pavement, whereas DBR can restore pavement conditions at a reasonable cost. However, not all DBR projects were successful. In one DBR project, faulting in the range of 6.4–9.5?mm occurred after less than 2 years of treatment. Forensic investigation revealed voids under the dowel bars, which indicates poor consolidation of the grout material. Efforts are currently underway in TxDOT to improve specifications for grout materials and DBR construction.     

Utilizing Advanced Characterization Tools to Prevent Reflective Cracking

To prevent premature failures of rehabilitated concrete pavements, transportation authorities need tools to characterize the prerehab pavement condition of its load carrying capacity, and to determine the resistance of the overlay material to underlying crack/joint movements. Two quantitative methods, the rolling dynamic deflectometer (RDD) and overlay tester (OT), along with field performance data were employed in rehabilitation studies involving reflective cracks. The RDD is able to continuously assess vertical differential movements at joints/cracks that represent the potential for reflective cracks on existing pavements. The OT has the ability to determine the resistance of the overlay material to underlying crack/joint movements. The RDD W1?W3 deflections were used to determine areas that have a high potential for reflective cracking due to poor load transfer across joints and cracks. This paper documents results from the RDD and OT on the following five rehabilitation projects: (1) SH225; (2) US96; (3) SH12; (4) SH342; and (5) IH35W. Based on the available test results from these five projects, it was observed that the W1?W3 threshold values of 5.5 mils (0.140 mm) for exposed concrete pavement and 6.5 mils (0.165 mm) for composite pavement with existing hot mix asphalt overlay and an OT threshold value of 700 cycles correlated well with the field performance. Ignoring either of these critical factors may lead to premature reflective cracking.     

Investigation of a Pavement Premature Failure on a Weak and Moisture Susceptible Base

An investigation was conducted to determine the root cause of the premature pavement failure. The premature pavement failure occurred in the form of rutting and alligator cracking. Although the affected portion was repaired by removing and replacing the top 75-mm asphalt concrete (AC), the repaired AC experienced recurring rutting and alligator cracking in a few weeks. Through extensive field and lab testing, it was found that the weak base is the root cause of the premature failure and the brittleness of the AC is secondary. However, both the base and AC were built according to plan and met the current material and field density requirements. It was concluded that density alone for construction quality control is not sufficient, as it was not able to protect against premature failures from occurring. Although there are many different ways to minimize premature failures, an immediate action is to include proof rolling in construction quality control. Proof rolling has been used with success to ensure proper compaction and to locate unstable areas, as the stability is greatly influenced by the degree of densification achieved during compaction.     

Detailed Forensic Investigation and Rehabilitation Recommendation on Interstate Highway-30

The main objective of this study is to identify the cause of the punchouts observed on Interstate Highway 30 (IH-30), and to identify possible rehabilitation alternatives. Several nondestructive tests, as well as coring and trenching, were conducted in both distressed and nondistressed areas. Middepth horizontal cracks were found during routine repair and by the trenching performed in this study. It is believed that due to temperature variation at an early stage, horizontal cracks developed at the middepth interface between the steel and concrete. The truck traffic caused the horizontal cracks to deteriorate further. Repetitive truck traffic and thermal loading forced the concrete to crack vertically from the middepth where there were horizontal cracks. The closely spaced transverse and longitudinal cracks, along with the delamination, caused punchouts. Although the problem is not imminent, an immediate seal plus a 75 mm heavy-duty stone matrix asphalt (SMA) overlay will probably provide the most cost-effective remedy for this section of IH-30. Existing distressed areas should be repaired before the rehabilitation. To slow the deterioration, the district should use a latex modified chip seal or asphalt rubber seal (AC15-5TR) followed by a 75 mm heavy duty SMA. This is to provide bonding between the concrete and SMA overlay. If the district chooses to do nothing at this time, it will become costly in 2–3 years if current environmental and traffic conditions hold. The cost to repair a severely deteriorated continuously reinforced concrete pavement (CRCP) would be several times more than the 75 mm heavy duty SMA overlay.     

Effect of Design and Site Factors on the Long-Term Performance of Flexible Pavements

Results are presented from a study to evaluate the relative influence of design and site factors on the performance of in-service flexible pavements. The data are from the SPS-1 experiment of the Long-Term Pavement Performance program. This experiment was designed to investigate the effects of HMA surface layer thickness, base type, base thickness, and drainage on the performance of new flexible pavements constructed in different site conditions (subgrade type and climate). Base type was found to be the most critical design factor affecting fatigue cracking, roughness (IRI), and longitudinal cracking (wheel path). The best performance was shown by pavement sections with asphalt treated bases (ATB). This effect should be interpreted in light of the fact that an ATB effectively means a thicker HMA layer. Drainage and base type, when combined, also play an important role in improving performance, especially in terms of fatigue and longitudinal cracking. Base thickness has only secondary effects on performance, mainly in the case of roughness and rutting. In addition, climatic conditions were found to have a significant effect on flexible pavement performance. Wheel path longitudinal cracking and transverse cracking seem to be associated with a wet-freeze environment, while nonwheel path longitudinal cracking seems to be dominant in a freeze climate. In general, pavements built on fine-grained soils have shown the worst performance, especially in terms of roughness. Although most of the findings from this study support the existing understanding of pavement performance, they also provide an overview of the interactions between design and site factors and new insights for achieving better long-term pavement performance.     

Forensic Evaluation of Premature Failures of Texas Specific Pavement Study–1 Sections

The Specific Pavement Study–1 pavement test section on US281 in south Texas comprise the largest Strategic Highway Research Program experimental site in the United States. The project was opened to traffic in 1997, and performance has been poor. Three of these test sections developed deep rutting within 1 year. Their surfaces were milled to restore ride quality. Three years after construction, 14 of the sections had 10 mm or more rutting. A forensic study was initiated by the Texas Department of Transportation to identify the cause of the problem. Nondestructive testing was conducted with both the falling weight deflector and ground penetrating radar. No structural problems were detected with either device, both indicating that the base and subbase layers were strong. A field investigation was initiated; the original plan was to cut nine trenches, however, after four trenches were cut, the problematic layer was identified and the trenching operation was terminated. Dynamic cone penetrometer, stiffness gauge, seismic pavement analyzer, and nuclear density gauge tests were then conducted on top of the base and subgrade layers. The trench profiles indicated that the rutting was coming primarily from the top 50-mm (2-inch) asphalt-concrete layer. Asphalt cores were taken from both rutted and nonrutted sections and bag samples of the base were tested in laboratory. The binder was recovered, and the asphalt content and penetration, aggregate gradation, and type were determined. The cause of the problem was traced to a change in aggregate screening, and also an excess of asphalt in the top layer.     

Inspecting the Lightweight Precast Concrete Panels in the Woodrow Wilson Bridge Deck of 1982

This paper presents the results of a detailed inspection of the deck panels of the Woodrow Wilson Bridge installed in 1982. The original cast-in-place concrete deck, constructed in 1962, was replaced with full-depth lightweight precast concrete deck panels that enabled rapid construction with minimal traffic disruption. The inspection of the Woodrow Wilson deck provides valuable information about the performance of the precast concrete panels, joints, and connections after 20 years of very harsh traffic loads and environmental stressors. The deck panels performed well overall, with the only serious problems at expansion and contraction joints. All of these joints exhibited cracking and rusting. The most prevalent type of cracking appeared to be due to restrained shrinkage between the new polymer concrete, the older precast panels, and the rigid steel joints. This location is more vulnerable to cracking and leaking because there is no prestress across the joint. The multilayered corrosion protection methods used for the transverse and longitudinal post-tensioning tendons were very successful.     

Successful Application of CLSM on a Weak Pavement Base/Subgrade for Heavy Truck Traffic

Lack of proper pavement base and subgrade compaction leads to premature failures that account for millions of dollars in damages. Controlled low-strength material (CLSM) concrete was introduced in this study as pavement base material near a manhole where proper compaction is unachievable. Rut-resistant stone matrix asphalt was placed on top of the CLSM as a wearing surface layer. Dynamic cone penetrometer (DCP) testing was used to monitor CLSM construction. One day after placing, the CLSM gained sufficient strength to support construction traffic. Further, DCP results indicated that the CLSM possessed uniform characteristics of concrete that could improve the load-bearing capacity and serviceability of the pavement near the manhole. After 18 months of heavy truck traffic, maximum rutting was 5?mm, well below the failure criteria of 12.5?mm. Based on cost and performance, CLSM concrete has the potential to improve problematic areas in pavement.     

Mechanistic Corrections for Determining the Resilient Modulus of Base Course Materials Based on Elastic Wave Measurements

The mechanical performance of pavement systems depends on the stiffness of subsurface soil and aggregate materials. The moduli of base course, subbase, and subgrade soils included in pavement systems need to be characterized for their use in the new empirical-mechanistic design procedure (NCHRP 1-37A). Typically, the resilient modulus test is used in the design of base and subbase layers under repetitive loads. Unfortunately, resilient modulus tests are expensive and cannot be applied to materials that contain particles larger than 25 mm (for 125-mm diameter specimens) without scalping the large grains. This paper examines a new methodology for estimating resilient modulus based on the propagation of elastic waves. The method is based on using a mechanistic approach that relates the P-wave velocity-based modulus to the resilient modulus through corrections for stress, void ratio, strain, and Poisson’s ratio effects. Results of this study indicate that resilient moduli are approximately 30% of Young’s moduli based on seismic measurements. The technique is then applied to specimens with large-grain particles. Results show that the methodology can be applied to large-grained materials and their resilient modulus can be estimated with reasonable accuracy based on seismic techniques. An approach is proposed to apply the technique to field determinations of modulus.     

Development of Flexural Strength Rating Procedures for Adjacent Prestressed Concrete Box Girder Bridges

An investigation was conducted on noncomposite prestressed precast concrete adjacent-box-beam bridges that suffered catastrophic failures resulting from the corrosion of the prestressing steel. These failures highlight the need to improve the methods used to detect corrosion damage and, subsequently, to load rate the damaged members. Currently, the inspection of concrete box girder sections relies on visual methods that correlate longitudinal and transverse cracking, spalling, and exposed strands with the rated level of performance of the member. To improve the current inspection techniques, visual assessment methods were examined through the destructive evaluation and material characterization of seven box-beam segments. The research results indicate that the fabrication techniques used for box-beam construction in the 1950–1960 time period allowed for large variations in construction tolerance. Half-cell methods were shown not to provide an accurate or reliable method of identifying the corrosion of prestressing strands. Longitudinal cracking was shown to be an accurate and reliable indicator of the underlying corrosion of prestressing strands. The probability of corrosion on strands adjacent to longitudinal cracks was determined and quantified. On the basis of the results, a new recommendation for determining the residual flexural strength of corroded prestressed beams is provided.     

Distributed Thermal Cracking of AC Pavement with Frictional Constraint

This paper develops a model to simulate the distributed thermal cracking of concrete structures with frictional constraint. This model is developed primarily for the thermal cracking asphalt-concrete (AC) pavement structures; however, with some modifications, it is also applicable to similar problems such as shrinkage cracking of concrete and cracking of reinforced concrete in uniaxial tension. This model reflects the multiscale nature of these problems: microcracking or damage on the mesoscale and localization or redistribution on the macroscale. Randomly distributed fictitious cracks are introduced to represent the inhomogeneities and damage in the material at the mesoscale. Friction is recognized as the mechanism leading to stress redistribution and, therefore, damage localization on the macroscale. When the problem is assumed to be 1D and Coulomb friction is used, a semianalytical numerical scheme is developed. The formation of stress-free open cracks is due to the combination of continuous crack growth and unstable jumps, which involve a nonlinear stability analysis. Equilibrium solutions and stability conditions are given in the paper. Displacement controlled analysis is used to follow the unstable equilibrium path after the structure has lost stability. Numerical simulations clearly show that, with slight mesoscale inhomogeneities and in the presence of a constraining frictional force, microcracking or damage on the mesoscale localizes and finally leads to open cracks distributed at a spacing on the order of the macroscale.     

金刚石有序排列对锯片性能的影响

排布方式合理的有序排列金刚石锯片能明显提高锋利性,增加寿命。试验采用2片无序排列锯片和4片有序排列锯片切割混凝土,不同排布方式的锯片切割性能有很大的差异。介绍了有序排列锯片制作的工艺流程,并且从理论上分析了排布参数对切割性能的影响,提出横向间距和纵向间距是有序排列方式设计中最重要的两个参数。     

高牌号3. 28 % Si钢冷轧板边裂机理分析和工艺改进

试验高牌号无取向硅钢（/%:0.006C,3.28Si,0.22Mn,0.030P,0.007S）的生产流程为180t BOF-真空精炼-230mm×（900~1750mm）板坯连铸-热轧成2.02mm板,冷轧成1.65mm板。从热轧基板的边部组织、力学性能、剪边以及断口显微形貌和成分等方面分析了冷轧高牌号硅钢中边裂的成因和机理。结果表明,高牌号硅钢冷轧板边部裂纹为解理断裂,热轧板料边部的存在混晶组织而导致塑性下降、圆盘切边引发撕裂带的裂纹和小凹坑是引发冷轧边裂主要因素;另外,边部断口处S和Mn的偏析也是引起边裂裂纹的重要因素;通过热轧过程减小边部与中部温差,热轧后圆盘剪刀片侧间隙由410μm减少到280μm,连铸过程电磁搅拌参数从380 A/3 Hz改进为350 A/6 Hz等工艺措施,使高牌号无取向硅钢冷轧板边裂发生率由原来的14%下降至4%。     

Degradation of a Granular Base under a Flexible Pavement: DEM Simulation

Flexible pavements are composed by an asphalt concrete layer, granular base and subbase layers, and a natural subgrade. The granular materials forming part of the granular layers are subjected to static and dynamic loads during their engineering life. As a result of these loads particle crushing may occur depending on the strength of the particles forming the granular layers. Particle crushing is important since it is associated with several detrimental effects such as settlements and a reduction in hydraulic conductivity. A computer simulation using the discrete element method (DEM) is presented in order to understand and visualize how crushing initiates and develops inside a simulated pavement structure.     

Investigation of Settlement of a Jointed Concrete Pavement

A section of jointed concrete pavement on U.S. 75, which was built from 1982 to 1985, in the Paris District of the Texas Department of Transportation (TxDOT) experienced severe pumping and settlement, even though two types of treatment (full depth repair and polyurethane foam injection) were performed. An extensive field investigation was conducted using ground penetrating radar, falling weight deflectometer, dynamic cone penetrometer, and coring to identify the causes of the continued pumping and settlement problems, and develop an optimal repair strategy. The pavement evaluation included tie bar condition, load transfer efficiency (LTE) at transverse and longitudinal construction joints, and base support conditions. Some of the tie bars failed in shear due to corrosion, which resulted in substantially low LTEs (<40%) at longitudinal construction joints. Pumping and settlement problems were more pronounced where the tie bars failed; the resulting large deflections exacerbated the pumping and settlement problems. The results demonstrate the importance of adequate LTEs (>80%) provided by tie bars, base and subgrade support, in providing satisfactory JCP performance. Inadequate design or construction of any of these critical elements could lead to performance problems, potentially including severe settlement, which is quite difficult to repair. To repair this pavement section, the Paris District of TxDOT is planning to retrofit tie bars by the “slot stitching” method, along with filling the voids under the slab using grout, followed by thin overlay using latex modified concrete to correct the differential elevation problems at longitudinal construction joints. It is expected that this repair strategy will address the distress problems and extend the pavement life.