Potential of DMSO as greener solvent for PES ultra‐ and nanofiltration membrane preparation

In this article, the performance of polyethersulfone (PES) ultra‐ and nanofiltration membranes, prepared with the non‐toxic solvent dimethyl sulfoxide (DMSO), was investigated. The membranes were prepared by immersion precipitation via phase inversion. Experimental results proved that DMSO is a better alternative to N‐methyl‐2‐pyrrolidone (NMP) as solvent for PES ultrafiltration membranes as the membranes had a higher permeability and rejection of bovine serum albumin (BSA). An explanation was found based on experimental cloud point data and scanning electron microscopy images showing the morphology. The rejection of BSA and rose Bengal (RB) was proportional to the polymer concentration. On the contrary, the permeability decreased with increasing polymer concentration. For a casting thickness of 250 µm, an optimal balance between permeability and rejection of macromolecules for ultrafiltration was found at 24 wt % PES. The permeability was inversely proportional to the casting thickness, but a small decrease in rejection was observed when lowering the thickness. A good balance between permeability and rejection of RB was found, using a reference nanofiltration membrane of 28.5 wt % PES with 150 µm casting thickness. This membrane achieved a RB rejection of 95.3% and a pure water flux of 2.03 L m^?2 h^?1 bar^?1. The membrane thickness and polymer concentration did not have a clear influence on the hydrophilicity of the membranes. It can be concluded that DMSO is a benign alternative as compared to traditional solvents such as NMP and also results in better PES membrane performances. DMSO is a perfectly suitable solvent for ultrafiltration applications and has potential to be used for nanofiltration applications. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46494.     

Improvement in antifouling and separation performance of PVDF hybrid membrane by incorporation of room‐temperature ionic liquids grafted halloysite nanotubes for oil–water separation

Novel hybrid poly(vinylidene fluoride) ultrafiltration membranes were fabricated via immersion precipitation method through the incorporation of the halloysite nanotubes functionalized with 1‐methyl‐3–(3‐triethoxysilypropyl) imidazolium chloride. The modified halloysite nanotubes were confirmed by Fourier transform infrared spectrometer, thermogravimetric analysis, and transmission electron microscopy. The morphologies of hybrid membranes were characterized by atomic force microscopy and energy dispersive spectrometer, while the filtration and antifouling performance were investigated by means of porosity, mean pore radius, pure water permeability, rejection ratio, and flux recovery ratio. The addition of the modified halloysite nanotubes obviously improved the membrane hydrophilicity. Besides, the flux recovery ratios were as high as 96% for humic acid and 94% for bovine serum albumin after two filtration cycles. Finally, the modified membranes were used to separate diesel oil–water emulsions. The rejection ratio and flux recovery ratio were as high as 99% and 94%, respectively. The poly(vinylidene fluoride) membranes incorporated by the novel halloysite nanotubes provided a promising alternative for oil–water emulsions separation. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46278.     

Sulfonated poly(ether ether ketone)‐induced porous poly(ether sulfone) blend membranes for the separation of proteins and metal ions

Asymmetric ultrafiltration (UF) membranes were prepared by the blending of poly(ether sulfone) (PES) and sulfonated poly(ether ether ketone) (SPEEK) polymers with N,N′‐dimethylformamide solvent by the phase‐inversion method. SPEEK was selected as the hydrophilic polymer in a blend with different composition of PES and SPEEK. The solution‐cast PES/SPEEK blend membranes were homogeneous for all of the studied compositions from 100/0 to 60/40 wt % in a total of 17.5 wt % polymer and 82.5 wt % solvent. The presence of SPEEK beyond 40 wt % in the casting solution did not form membranes. The prepared membranes were characterized for their UF performances, such as pure water flux, water content, porosity, and membrane hydraulic resistance, and morphology and melting temperature. We estimated that the pure water flux of the PES/SPEEK blend membranes increased from 17.3 to 85.6 L m^?2 h^?1 when the concentration of SPEEK increased from 0 to 40 wt % in the casting solution. The membranes were also characterized their separation performance with proteins and metal‐ion solutions. The results indicate significant improvement in the performance characteristics of the blend membranes with the addition of SPEEK. In particular, the rejection of proteins and metal ions was marginally decreased, whereas the permeate flux was radically improved. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Effect of silver loaded sodium zirconium phosphate (nanoAgZ) nanoparticles incorporation on PES membrane performance

Polyethersulfone (PES) based ultrafiltration membranes were fabricated via phase inversion by adding silver-loaded sodium zirconium phosphate nanoparticles (nanoAgZ) in PES casting solutions. The effect of nanoAgZ concentration on the membrane performance, i.e., morphology, hydrophilicity, thermal stability, permeation and antifouling properties was investigated. The results of thermal gravitational analysis (TGA) showed that the thermal stability of the hybrid membrane had been improved by the addition of nanoAgZ particles. Contact angle results indicated that the hydrophilicity of the modified membranes was enhanced. The contact angle of the membrane decreased from 71.5° to 52.6° with the increase of the nanoparticle content in the casting solution. Permeation experiment results showed that the modified PES membranes demonstrate better separation performance over the pure PES membrane. The pure water flux of PES membrane increased from 82.1 L/m² h to 100.6 L/m² h with the addition of the nanoparticles. Most importantly, the incorporation of the nanoAgZ particles enhanced the BSA fouling resistance and also the anti-biofouling performance of the membrane.     

Preparation and characterization of hydrophilic and antifouling poly(ether sulfone) ultrafiltration membranes modified with Zn–Al layered double hydroxides

Zn–Al layered double hydroxide (LDH)‐entrapped poly(ether sulfone) (PES) ultrafiltration membranes with four different weight percentages, 0.5, 1.0, 2.0, and 3.0%, were prepared by a phase‐inversion method. Characterization by scanning electron microscopy, atomic force microscopy and contact angle (CA), equilibrium water content, porosity, average pore size, mechanical strength, and ζ potential measurement were used to evaluate the morphological structure and physical and chemical properties of membranes. Static protein adsorption, filtration, and rejection experiments were conducted to study the antifouling properties, water permeability, and removal ability of the modified membranes. The results show that significant change occurred in the membrane morphology and that better hydrophilicity, water permeability, and antifouling ability were also achieved for the PES/LDH membranes when a proper amount of LDH was used. For example, the CA value decreased from 66.60 to 50.21°, and the pure water flux increased from 80.21 to 119.10 L m^?2 h^?1 bar^?1 when the LDH loading was increased from 0 to 2.0 wt %. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43988.     

Synthesis of well‐defined amphiphilic block copolymers via AGET ATRP used for hydrophilic modification of PVDF membrane

A well‐defined amphiphilic block copolymer consisting of a hydrophobic block poly(methyl methacrylate) (PMMA) and a hydrophilic block poly[N,N–2‐(dimethylamino) ethyl methacrylate] (PDMAEMA) was synthesized by activator generated by the electron transfer for atom transfer radical polymerization method (AGET ATRP). Kinetics study revealed a linear increase in the graph concentration of PMMA‐b‐PDMAEMA with the reaction time, indicating that the polymer chain growth was consistent with a controlled process. The gel permeation chromatography results indicated that the block copolymer had a narrow molecular weight distribution (Mw/Mn = 1.42) under the optimal reaction conditions. Then, poly(vinylidene fluoride) (PVDF)/PMMA‐b‐PDMAEMA blend membranes were prepared via the standard immersion precipitation phase inversion process, using the block copolymer as additive to improve the hydrophilicity of the PVDF membrane. The presence and dispersion of PMMA‐b‐PDMAEMA clearly affected the morphology and improved the hydrophilicity of the as‐synthesized blend membranes as compared to the pristine PVDF membranes. By incorporating 15 wt % of the block copolymer, the water contact angle of the resulting blend membranes decreased from pure PVDF membrane 98° to 76°. The blend membranes showed good stability in the 20 d pure‐water experiment. The bovine serum albumin (BSA) absorption experiment revealed a substantial antifouling property of the blend membranes in comparison with the pristine PVDF membrane. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42080.     

Effects of coagulation bath temperature on performances of polyethersulfone membranes modified by nanosilver particles in situ reduction

In this work, an in situ reduction method was used to prepare nanosilver‐modified polyethersulfone (PES‐Ag) ultrafiltration membranes by mixing up the reducing agent ethylene glycol and the protective agent polyvinylpyrrolidone to reduce AgNO₃ in the casting solution. The effects of coagulation bath temperature (CBT) on the separation performances, antifouling property, tensile strength, and stability of the nanosilver particles were researched. The results indicated that when the PES‐Ag membranes were prepared in 40°C coagulation bath, the loss rate of nanosilver particles during preparation was minimum, only 18.5%. With the CBT increasing from 20 to 60°C, the water flux of the PES and PES‐Ag membranes increased, whereas the rejection rate decreased. The largest flux reached 471 L·m^?2·h^?1 for PES‐Ag membranes prepared at 60°C and the rejection was over 90%. The results of contact angle and flux recovery ratio showed that PES‐Ag membranes had better hydrophilicity and antifouling property. Furthermore, the PES‐Ag membranes could inhibit Escherichia coli from growing. POLYM. ENG. SCI., 2013. © 2012 Society of Plastics Engineers     

One‐pot synthesized poly(vinyl pyrrolidone‐co‐methyl methacrylate‐co‐acrylic acid) blended with poly(ether sulfone) to prepare blood‐compatible membranes

In this study, a random copolymer of poly(vinyl pyrrolidone‐co‐methyl methacrylate‐co‐acrylic acid) was synthesized via a one‐pot reaction with the reversible addition–fragmentation chain‐transfer method and was then blended with poly(ether sulfone) (PES) to prepare flat‐sheet membranes that were expected to have anticoagulant and antifouling properties. The synthesized copolymer was characterized by Fourier transform infrared (FTIR) and NMR spectroscopy. The molecular weights and molecular weight distributions were determined by gel permeation chromatography. Elemental analysis was used to calculate the molar ratios of vinyl pyrrolidone (VP), methyl methacrylate (MMA), and acrylic acid (AA) in the copolymer. A liquid–liquid phase‐inversion technique was used to prepare the copolymer‐blended PES membranes. X‐ray photoelectron spectroscopy and attenuated total reflectance–FTIR spectroscopy were used to investigate the copolymer on the membrane surfaces. Compared with the pristine PES membrane, the modified PES membranes showed improved hydrophilicity, low hemolysis ratios, decreased protein adsorption, and suppressed platelet adhesion. Furthermore, the thrombin time and activated partial thromboplastin time indicated that the blood compatibility of the modified PES membranes were improved. The results of the 3‐(4,5‐Dimethylthiazol‐2‐yl)‐2,5‐diphenyltetrazolium bromide (MTT) assay and the cell morphology suggested that the cytocompatibility increased. In addition, the modified membranes showed good protein antifouling properties. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 4284–4298, 2013     

Polyethersulfone-polyvinylpyrrolidone composite membranes:Effects of polyvinylpyrrolidone content and polydopamine coating on membrane morphology,structure and performances

Hydrophilic modification is a promising method to inhibit fouling formation on ultrafiltration membrane.In this work,different mass concentrations (1％-16％) of hydrophilic polyvinylpyrrolidone were incorpo-rated into polyethersulfone (PES) membranes fabricated by none-solvent induced phase separation.Then,polydopamine (PDA) coating on the surface of prepared membrane was carried out at pH 8.5.The mor-phology and structure,surface hydrophilicity,permeation flux,BSA rejection,antifouling and stability performances of PES and PDA/PES modified membranes were investigated in detail.The results indicated that PDA was successfully attached onto the membranes.Membrane hydrophilicity was evaluated by water contact angle measurement.The contact angles of modified membranes reduced remarkably,sug-gesting that the membrane hydrophilicities were significantly increased.The results of filtration tests,which were done by dead-end filtration of bovine serum albumin solution,showed that the properties of permeability and fouling resistance were obviously improved by PDA modification.When polyvinylpyrrolidone mass content reached 10％,flux recovery ratio of modified membrane was up to 91.23％,and its BSA rejection were over 70％.The results of stability tests showed that the modified mem-branes had good mechanical stability and chemical stability.This facile fabrication procedure and out-standing performances suggested that the modified membranes had a potential in treating fouling.     

Preparation of PVDF/poly(tetrafluoroethylene‐co‐vinyl alcohol) blend membranes with antifouling propensities via nonsolvent induced phase separation method

Poly(vinylidene fluoride) (PVDF) was blended with a new amphiphilic copolymer, poly(tetrafluoroethylene‐co‐vinyl alcohol) [poly(TFE‐VA)], via non‐solvent induced phase separation (NIPS) method to make membranes with superior antifouling properties. The effects of the VA/TFE segment ratio of the copolymer and the copolymer/PVDF blend ratio on the properties of the prepared membranes were studied. Membranes with similar water permeabilities, surface pore sizes, and rejection properties were prepared and used in bovine serum albumin (BSA) filtrations with the same initial water flux and almost the same operating pressure, to evaluate the sole effect of membrane material on fouling propensity. While the VA/TFE segment ratio strongly affected the membrane antifouling properties, the effects of the copolymer/PVDF blending ratio were not so drastic. Membrane surface hydrophilicity increased, and BSA adsorption and fouling decreased upon blending a small amount of amphiphilic copolymer with a high VA/TFE segment ratio with PVDF (copolymer/PVDF blending ratio 1:5). © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43780.     

Preparation of high‐flux ultrafiltration membranes by blending strongly charged polymer

Three kinds of high‐flux ultrafiltration membranes were fabricated by blending strongly charged polymer [sulfonated poly(phenylene oxide) (SPPO)] with neutral polymer [cellulose acetate (CA), polyethersulfone (PES), or polyvinylidene fluoride (PVDF)]. After blending with SPPO, the pure water flux of CA‐SPPO, PES‐SPPO, and PVDF‐SPPO membrane increase by 3, 76, and 30 times at a transmembrane pressure of 100 kPa. Compared with the unblended membranes, the pore radius of CA‐SPPO, PES‐SPPO, and PVDF‐SPPO membrane increased from 31.9 to 33.2 nm, 26.1 to 28.6 nm, and 19.8 to 25.7 nm, respectively. The addition of strongly charged polymer decreased the thermodynamic stability of casting solutions, promoting the phase inversion process and resulting in highly porous structure. The charged groups and hydrophilicity of the polymer facilitate the formation of an additive concentration gradient (more additive in the active layer), endowing the blend membrane with better hydrophilicity and greater wettability gradient. The high porosity, good hydrophilicity, and larger wettability gradient enable the high permeation of blend membranes. This work shows how the strongly charged polymer affects the formation and performance of blend membrane, which will be useful for designing high‐performance membrane. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44570.     

Conferring pH-sensitivity on poly (vinylidene fluoride) membrane by poly (acrylic acid-co-butyl acrylate) microgels

In this paper, cross-linked poly (acrylic acid-co-butyl acrylate) microgels were utilized to impart pH-sensitivity to poly (vinylidene fluoride) membranes by phase separation of a casting solution of poly (vinylidene fluoride)/poly (acrylic acid-co-butyl acrylate)/DMF in aqueous solution. The effect of microgels content on morphologies, surface composition, and chemistry of the as-prepared membranes was studied by varieties of spectroscopic and microscopic characterization techniques. By using the filtration of water and protein aqueous solution, the performance of the membrane was evaluated. Results indicated that the as-prepared membrane was pH-sensitive to water flux, bovine serum albumin rejection and antifouling property. Besides, the as-prepared membrane showed an obvious improvement of water flux and proper bovine serum albumin rejection ratio, compared to the pristine PVDF membrane. Meanwhile, dynamic bovine serum albumin fouling resistance and flux recovery property were also greatly enhanced due to the improvement of surface hydrophilicity. Hopefully, the hydrophilic microgels additive would be favorable to fabricate other polymer membranes for water treatment.     

Antifouling performance enhancement of polyethersulfone ultrafiltration membrane through increasing charge-loading capacity over Prussian blue nanoparticles

Prussian blue (PB), as a kind of regulator of charge-loading capacity, was first used to modify polyethersulfone (PES) membrane, and a novel PB/PES ultrafiltration membrane was prepared by non-solvent induced phase separation method. The physicochemical properties of PB-NPs and PB/PES membranes were analyzed by Fourier-transform infrared spectroscopy, X-ray diffraction, scanning electron microscope, atomic force microscope, and zeta potential analysis. It was observed that PB-NPs were uniformly distributed in the PES matrix and a lotus-seedpod structure was formed inside the membrane. The addition of PB-NPs improved the charge-loading capacity of the PES membrane. The permeation and antifouling performance were investigated by filtering bovine serum albumin aqueous solution with different pH values. The results showed that the PB/PES membrane with 0.2-wt% PB-NPs content had the excellent antifouling performance and the flux recovery ratio value reached 90.73%. Moreover, the long-term stability test showed that PB-NPs did not fall off after continuous pure water filtration, indicating that PB/PES membrane had a good stability.     

Poly(vinylidene fluoride)–polyacrylonitrile blend flat‐sheet membranes reinforced with carbon nanotubes for wastewater treatment

In this reported study, poly(vinylidene fluoride) (PVDF) and polyacrylonitrile (PAN) blend flat‐sheet membranes were prepared via a phase‐inversion method with various loadings of multiwalled carbon nanotubes. The effects of the carbon nanotubes (CNTs) on the performance and morphology of the PVDF–PAN composites were investigated via tests of the pure water flux and rejection of bovine serum albumin, scanning electron microscopy, atomic force microscopy, Fourier transform infrared spectroscopy, X‐ray diffraction, thermogravimetric analysis, and contact angle (CA) analysis. The experimental results demonstrate that the CNTs contributed to the improvement of the flux and hydrophilicity of the membranes. The maximum value of the flux was 398.1 L m^?2 h^?1, and the value of CA for the composite membranes was found to be 48°. In addition, the results of the mechanical properties tests illustrate that the brittleness and plasticity of the hybrid membranes were greatly improved by the presence of the CNTs. The flux recovery ratio was maintained at 75%; this demonstrated that the PVDF–PAN membranes enhanced with the CNTs possessed good antifouling performance. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46155.     

Amphiphilic poly(vinyl chloride)‐g‐poly[poly(ethylene glycol) methylether methacrylate] copolymer for the surface hydrophilicity modification of poly(vinylidene fluoride) membrane

In this study, a comblike amphiphilic graft copolymer containing poly(vinyl chloride) (PVC) backbones and poly(oxyethylene methacrylate) [poly(ethylene glycol) methylether methacrylate (PEGMA)] side chains was facilely synthesized via an atom transfer radical polymerization method. Secondary chlorines in PVC were used as initial sites to graft a poly[poly(ethylene glycol) methylether methacrylate] [P(PEGMA)] brush. The synthesized PVC‐g‐P(PEGMA) graft copolymer served as an efficient additive for the hydrophilicity modification of the poly(vinylidene fluoride) (PVDF) membrane via a nonsolvent‐induced phase‐inversion technique. A larger pore size, higher porosity, and better connectivity were obtained for the modified PVDF membrane; this facilitated the permeability compared to the corresponding virgin PVDF membrane. In addition, the modified PVDF membrane showed a distinctively enhanced hydrophilicity and antifouling resistance, as suggested by the contact angle measurement and flux of bovine serum albumin solution tests, respectively. Accordingly, the PVC‐g‐P(PEGMA) graft copolymer was demonstrated as a successful additive for the hydrophilicity modification, and this study will likely open up new possibilities for the development of efficient amphiphilic PVC‐based copolymers for the excellent hydrophilicity modification of PVDF membranes. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Outstanding antifouling performance of poly(vinylidene fluoride) membranes: Novel amphiphilic brushlike copolymer blends and one-step surface zwitterionization

In this study, we endowed a poly(vinylidene fluoride) (PVDF) membrane with outstanding antifouling ability by blending the hierarchical amphiphilic brushlike copolymer [poly(hydroxyethyl methacrylate)-b-polydimethylsiloxane-b-poly(hydroxyethyl methacrylate)]-g-poly(N,N-dimethylamino-2-ethyl methacrylate) with different initial monomer/initiator feed ratios and performing a one-step surface zwitterionization of spontaneously segregated poly(N,N-dimethyl aminoethyl methacrylate) segments. Interestingly, nanoscale granular micelles were formed on the surface during zwitterionization because of the migration and self-assembly of the amphiphilic copolymer; this contributed to the membrane hydrophilicity and antifouling ability. During the filtration of the model foulant bovine serum albumin (BSA) aqueous solution, the BSA rejection ratio and flux recovery ratio increased remarkably to 94.8 and 100.0%, respectively. Moreover, the modified membranes also possessed stable and durable antifouling properties after three cycles of BSA filtration. Thus, this study provided a versatile method for constructing a PVDF ultrafiltration membrane that could achieve high permeability and good antifouling properties in efficient wastewater treatment. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47637.     

Preparation and characterization of antifouling and antibacterial polysulfone ultrafiltration membranes incorporated with a silver–polydopamine nanohybrid

A silver–polydopamine (Ag–PDA) nanohybird was used to produce polysulfone (PSf) ultrafiltration membranes with excellent antifouling and antibacterial properties. First, the catechol functional groups of polydopamine (PDA) helped with the in situ immobilization of silver (Ag) nanoparticles (<10 nm) on the PDA sphere surface; this led to the formation of the Ag–PDA nanohybrid. Then, Ag–PDA/PSf hybrid membranes were prepared via the phase‐inversion method, and the influence of Ag–PDA loading on the hybrid membrane properties was systematically investigated. When the content of Ag–PDA was 0.5 wt %, the hybrid membrane achieved optimal separation performance, including a dramatically increased pure water flux and a well‐maintained bovine serum albumin rejection. Furthermore, the Ag–PDA/PSf hybrid membranes presented a significantly enhanced protein‐fouling resistance and a good antibacterial activity. These improvements were attributed to the unique structure and properties of the Ag–PDA nanohybrid because of the synergistic effect of the hydrophilic PDA substrate and well‐distributed Ag nanoparticles. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46430.     

Preparation and characterization of modified ultrafiltration nylon 6 membrane modified by poly (acrylamide-co-maleic anhydride)

In attempt to prepare modified ultrafiltration (UF) Nylon 6 membrane and improve its hydrophilicity and anti-fouling performance, poly (acrylamide-co-maleic anhydride)(AM-MA) was utilized as hydrophilic copolymer additive in the dope solution. The UF Nylon 6/AM-MA membranes were synthesized through blending Nylon 6 with poly(AM-MA) using a phase inversion process. Characterization of the prepared membranes for morphological studies and thermal behavior was carried out by SEM and DSC instruments respectively. The SEM photos demonstrated that by increasing the copolymer density in the dope solution, the morphology was changed from spongy to bi-continuous, composed of small interlocked and stick-like crystallites. FTIR/ATR and water contact angle data also confirmed the existence of AM-MA copolymer on the blend membranes surface. Furthermore, the effect of different molecular weights and concentration of hydrophilic copolymer on filtration performance and antifouling properties were experimentally studied. The results exhibited that the blend UF membranes possessed better water flux permeability than pure Nylon 6 membrane due to the increased surface hydrophilicity and porosity. Fouling resistance experiments revealed that the surface anti-fouling ability of the blend membranes was improved via the addition of AM-MA copolymer with lower MW (co1) to the cast solution, while this parameter was weakened in higher MW of copolymer (co2).     

Antifouling and blood‐compatible poly(ether sulfone) membranes modified by zwitterionic copolymers via In situ crosslinked copolymerization

A novel and simple but practical method for the preparation of modified poly(ether sulfone) (PES) membranes was provided by the in situ crosslinked copolymerization of sulfobetaine methacrylate (SBMA) and sodium p‐styrene sulfonate (NaSS) in PES solution followed by a phase‐separation technique. Then, semi‐interpenetrating network membranes modified by the crosslinked copolymers of poly(sulfobetaine methacrylate‐co‐sodium p‐styrene sulfonate) [P(SBMA‐co‐NaSS)] were prepared. The SBMA‐containing copolymer‐modified membranes showed improved protein antifouling properties with flux recovery ratios above 90%. Furthermore, the anticoagulant properties of the NaSS‐containing copolymer‐modified membranes were obviously enhanced; their activated partial thromboplastin time could be prolonged to about 115 s. Thus, the P(SBMA‐co‐NaSS) zwitterionic copolymer‐modified membranes showed improved antifouling properties and blood compatibility and will provide wide choices for their specific applications. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41585.     

Antifouling microfiltration membranes prepared from poly(vinylidene fluoride)‐graft‐Poly(N‐ vinyl pyrrolidone) powders synthesized via pre‐irradiation induced graft polymerization

Poly(vinylidene fluoride) (PVDF) powders were grafted with N‐vinyl pyrrolidone using the pre‐irradiation induced graft polymerization technique. The effects of reaction time, absorbed dose, and monomer concentration on the degree of grafting were investigated, and the grafted PVDF powders were characterized by Fourier transform infrared spectroscopy, thermogravimetric analysis, and differential scanning calorimetry. The grafted PVDF powders were also cast into microfiltration (MF) membranes via the phase‐inversion method. The contact angle and water uptake were measured. The membrane morphology was studied by scanning electron microscopy, and the water filtration properties of the membranes were tested. The antifouling properties were determined through measurements of the recovery percentage of pure water flux after the MF membranes were fouled with bovine serum albumin solution. The results confirmed that the existence of poly(N‐vinyl pyrrolidone) (PVP) graft chains improved the hydrophilicity and antifouling properties of the MF membranes cast from PVDF‐g‐PVP powders. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013