High‐performing dye‐sensitized solar cells based on reduced graphene oxide/PEDOT‐PSS counter electrodes with sulfuric acid post‐treatment

Four kinds of counter electrodes are prepared with polystyrene‐sulfonate doped poly(3,4‐ethylenedioxythiophene) (PEDOT‐PSS) as basic material, reduced graphene oxide (rGO) sheets as additives and H₂SO₄ as treating agent. The cyclic voltammetry and Tafel polarization are measured to evaluate catalytic activity of these counter electrodes for /I^? redox couple. It is found that H₂SO₄ treated rGO and PEDOT‐PSS hybrid counter electrode (S/rGO/PEDOT‐PSS counter electrode) has the highest catalytic activity among these counter electrodes. Power conversion efficiency of the dye‐sensitized solar cell with S/rGO/PEDOT‐PSS counter electrode can attain to 7.065%, distinctly higher than that of the cells with the other three ones, owing to the great enhanced fill factor and short‐circuit current density. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42648.     

Synthesis and characterization of dendritic polypyrrole silver nanocomposite and its application as a new urea biosensor

Polypyrrole and its silver nanocomposite were electrochemically synthesized from aqueous solutions containing pyrrole, potassium chloride (KCl) (system A); pyrrole, KCl, and an anionic surfactant sodium dodecyl sulphate (NaDS) (system B); and pyrrole, silver nitrate, NaDS (system C). Compact and dendritic patterns were observed depending on experimental conditions. The aggregates were characterized by powder X‐ray diffraction, energy‐dispersive X‐ray spectroscopy, scanning electron microscopy, high resolution transmission electron microscopic (HRTEM), and thermal studies (TG/DTG). HRTEM studies indicate that the particle size of PPy‐Ag nanocomposite is ～30 nm. TG studies revealed that systems B and C, have different thermal behavior. Potassium ion selective electrodes were constructed using systems A, B, and C. The electrode prepared with PPy‐Ag nanocomposite showed nernstian behavior with maximum slope of 57 mV. ion‐selective electrode was also constructed for this system based on nonactin‐impregnated PVC matrix membrane. Urease enzyme was immobilized at the surface of as made ion‐selective electrode to develop urea biosensor showing good detection limit. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45705.     

Synthesis and characterization of PEDOT derivative with carboxyl group and its chemo sensing application as enhanced optical materials

Poly(4‐(((2,3‐dihydrothieno[3,4‐b][1,4]dioxin‐2‐yl)methoxy)methyl)benzoic acid) (PEDOT‐Ph‐COOH) was facilely synthesized by the direct electropolymerization of 4‐(((2,3‐dihydrothieno[3,4‐b][1,4]dioxin‐2‐yl)methoxy)methyl)benzoic acid (EDOT‐Ph‐COOH) in CH₂Cl₂‐Bu₄NPF₆ (0.10 M) system, and the PEDOT‐Ph‐COOH films were systematically investigated. The results displayed that the film had excellent reversible redox activities, good electrochemical performance, and rough and compact surface. Finally, the PEDOT‐Ph‐COOH film was used as an optical chemo‐sensor for the highly selective and sensitive detection of F^?, , , , Cu²⁺, and Fe³⁺ in dimethyl sulfoxide. Satisfactory results indicated that optical chemo‐sensor based on PEDOT‐Ph‐COOH possessed an excellent sensing performance and enhanced optical response, and it might be as potential promising materials, such as electrochromic devices, supercapacitors and so on. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41559.     

Molybdate‐doped copolymer coatings for corrosion prevention of stainless steel

The polypyrrole and polyaniline copolymer coating (PPy‐PAni) and PPy‐PAni doped with sodium molybdate copolymer coating ( ) were synthesized on stainless steel by cyclic voltammetry. The effect of molybdate on the passivation of stainless steel was investigated by linear sweep voltammetry in 0.2 mol L^?1 of oxalic acid. The corrosion prevention performances of these copolymer coatings for stainless steel were investigated by linear sweep voltammetry, electrochemical impedance spectroscopy in 1 mol L^?1 of sulfuric acid, and potentiodynamic polarization in 0.1 mol L^?1 of hydrochloric acid. Copolymer coating doped with molybdate could accelerate the formation of the passive oxide film and have better corrosion prevention efficiencies than PPy‐PAni coating on stainless steel. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40602.     

Viscoelastic properties of borax loaded CMC‐g‐cl‐poly(AAm) hydrogel composites and their boron nutrient release behavior

Borax (Na₂B₄O₇, 10.5% Boron) loaded CMC‐g‐cl‐poly(AAm) hydrogel composites were prepared by in situ grafting of acrylamide on to sodium carboxymethyl cellulose in the presence of borax by free radical polymerization technique to develop slow boron (B) delivery device. The composition, morphology, and mechanical properties of synthesized composites were studied by X‐ray diffraction, Fourier transform infrared spectroscopy, scanning electron microscopy, texture analyser, and dynamic shear rheometer. Characterization revealed formation of borate ion ( ) from borax during polymerization reaction leading to extensive crosslinking of cellulosic chains and generation of mechanically strong composite hydrogels. Dynamic release of from the synthesized composites hydrogels followed Fickian diffusion mechanism and composites with high mechanical strength resulted in slow release of B. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43969.     

Heat‐ and light‐induced thiol‐ene oligomerization of soybean oil‐based polymercaptan

Polymercaptanized soybean oil (PMSO), the product of a thiol‐ene reaction between soybean oil and hydrogen sulfide, is a material of interest as a lubricant additive and polymer precursor. We investigated with gel permeation chromatography, nuclear magnetic resonance (one‐dimensional and two‐dimensional), gas chromatography–mass spectrometry, and viscometry the changes that occur with PMSO upon heating or ultraviolet irradiation. The observed changes were due to a further thiol‐ene reaction between the thiol groups and the residual unsaturation. The formation of oligomers was a result of new sulfide bridges. Additionally, tetrahydrothiophene moieties were detected. An almost linear increase of the average molecular weight (MW) and the polydispersity index (PDI) was observed upon heat treatment [number‐average MW ( ) = 1180 Da, PDI = 1.32 for PMSO, = 1720 Da, PDI = 2.17 for PMSO that was heated for 1000 h at 130 °C]. PDI correlated best with the z‐average MW. The was the best predictor of the viscosity. For samples with close , the higher PDI corresponded to a higher viscosity index. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46150.     

Effect of K0.5Na0.5NbO3 filling particles on the charge carrier trap distribution of polyimide films

Polyimide (PI) films filled with K_0.5Na_0.5NbO₃ (KNN50) particles at different weight 0, 5, 10, and 15 wt % had been prepared by in‐situ dispersion polymerization process. The thermally stimulated current (TSDC) method was used to investigate the charge carrier trap levels and their distribution of the composite films. The TSDC spectra show that pure film has ‐peaks and ‐peak, but the composite films only have ‐peaks and an extraordinary peak at high temperature region. The trap parameters were calculated by an approximate model, and the results indicate that charge released of the shallow traps show a nonlinear behavior. The trap energies decrease from 0.879–0.968 eV to 0.549–0.839 eV with the increase of the KNN50 content. The surface and interface between KNN50 and PI matrix was considered to the variation of the trap levels. The extraordinary peak of the composite films was correlated with the phase transition of the KNN50 particles. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39828.     

Reinforcement of polysiloxane/silica elastomer composite by introduction of sacrificial bonds

It is a challenge to improve tear strength of silicone rubber, especially at high filler loading circumstances. A method is offered here to introduce sacrificial bonds into the system. In particular, amide group was introduced onto the phenyl group of monomer methyl phenyl cyclosiloxane ( first, and this functionalized monomer ( was further used for copolymerization with octamethylcyclotetrasiloxane (D₄) and 2,4,6,8‐tetravinyl‐2,4,6,8‐tetramethyl‐cyclotetrasiloxane ( ). Vulcanizates composed by this new copolymer (1A‐50) which amide group‐containing is 1 wt % and with 50 phr TS‐530 exhibit high tear strength of about 54 N ? mm^?1, which is three times higher than that composed by polydimethylsiloxane (PDMS)/TS‐530 (50 phr). The mechanical test indicates this new copolymer a promising candidate for the construction of high tear resistant silicone rubber, especially at high filler loading circumstances. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46129.     

Synthesis of aminated glycidyl methacrylate grafted rice husk and investigation of its anion‐adsorption properties

In this study, we focused on the synthesis, characterization, and adsorption capacity testing of aminated glycidyl methacrylate grafted rice husk (RH‐g‐GMA–Am). Our goal was to obtain a high‐performance surface for the adsorption of various anions. Glycidyl methacrylate grafted rice husk (RH‐g‐GMA) was prepared by the graft copolymerization of glycidyl methacrylate with rice husk; the product was further subjected to an amination reaction. The surface properties, sorption characteristic functional groups, isotherm and kinetic studies, pore diffusion models, and effects of the temperature and pH on the material properties were studied under batch conditions. The IR spectroscopy results show additional surface functional groups for RH‐g‐GMA–Am. The adsorptions of and on RH‐g‐GMA–Am were found to follow pseudo‐second‐order kinetics; this indicated a possible dominant role played by chemisorption. The rate‐limiting step for mass transfer was found to be boundary layer diffusion. Furthermore, the sorption isotherms for and fit the Langmuir model. The amination of RH‐g‐GMA drastically increased the removal efficiency from 3 to 82% and from 6 to 93% for and , respectively. Moreover, RH‐g‐GMA–Am exhibited a better removal efficiency in the pH range of 4–6.5. Regeneration studies revealed that the surface of RH‐g‐GMA–Am could be regenerated repetitively by simple acid washing with an insignificant decrease in the active surface for consecutive adsorptions. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43002.     

Processing behavior and mechanical properties of autopolymerizing hypoallergenic denture base polymers

Driven by the phenomenon of increasing irritations and allergic reactions of dental prosthesis carriers preferably due to residual methyl methacrylate monomer in conventional dental materials, autopolymerizing hypoallergenic denture base polymers were prepared as two‐component materials in the shape of paste/paste‐ or powder/liquid systems. The processing behavior of these materials was investigated regarding the processing and solidification times also in dependence on the polymerization catalyst concentration, whereas the whole processing and curing characteristics and the final polymer properties were evaluated by dynamic mechanical analysis in shear mode in the temperature range from ?145°C to 200°C. The mechanical properties of the hypoallergenic denture base polymers were validated regarding stiffness (flexural modulus E') and fracture toughness (maximum factor of loading intensity , total work of fracture ) and the effects of monomer composition, kind of resin powder, impact modification by the liquid component, and water immersion on these properties were investigated. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41378.     

Electrical properties and the role of inhomogeneities at the polyvinyl alcohol/n‐inp schottky barrier interface

In this work, we have investigated the electrical properties of Au/n‐InP contacts with a thin layer of polyvinyl alcohol (PVA) as an interlayer. The current–voltage (I–V) and capacitance–voltage (C–V) measurements are carried out in the temperature range of 175–425 K. The Au/PVA/n‐InP Schottky structure show nonideal behaviors and indicates the presence of a nonuniform distribution of interface states. The temperature dependent interface states densities (N_SS), ideality factor and barrier height are obtained. An abnormal decrease in zero‐bias barrier height (BH) and increase in the ideality factor ( ) with decreasing temperature have been explained on the basis of the thermionic emission theory with Gaussian distribution (GD) of the BHs due to the BH inhomogeneities. The experimental I–V characteristics of Au/PVA/n‐InP Schottky diode has revealed the existence of a double GD with mean BH values of ( ) of 1.246 and 0.899 eV and standard deviation ( ) of 0.176 and 0.137 V, respectively. Consequently, the modified conventional activation energy versus plot gives and Richardson constants ( ) and the values are 1.17 and 0.71 eV and 9.9 and 6.9 A/cm² K², respectively, without using the temperature coefficient of the BH. The effective Richardson constant value of 9.9 A/cm² K² is very close to the theoretical value of 9.4 A/cm² K² for n‐InP. The discrepancy between Schottky barrier heights estimated from I–V and C–V measurements is also discussed. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39773.     

Removal of ammonium‐nitrogen from aqueous solution using chitosan‐coated bentonite: Mechanism and effect of operating parameters

Wastewater containing high concentration of ammonium‐nitrogen ( ) is not effectively addressed by biological treatment and when released into water bodies can cause eutrophication. In this study, the removal of from simulated wastewater using chitosan‐coated bentonite (CCB) was investigated. The effects of salt used, pH, CCB dosage, agitation rate, and temperature on the removal of were studied. The highest removal of 67.5% was attained at the following conditions: initial pH 4.0, CCB dose of 8.0 g, agitation rate of 150 rpm, and temperature of 35 °C. Fourier transform infrared analysis indicated two mechanisms: adsorption onto CCB involving hydrogen bonding with hydroxyl groups ( OH) and ion exchange between and cations present in the interlayer of bentonite. Experimental data follows the pseudo‐second‐order kinetic model (R² = 0.9964) and Koble–Corrigan isotherm (R² = 0.9705). Thermodynamic studies showed that the adsorption process is spontaneous (ΔG⁰ < 0), endothermic (ΔH⁰ > 0) in nature, and leads to an increase in randomness at the solid–solution interface (ΔS⁰ > 0). © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45924.     

Sorption and thermal properties of strongly basic cross‐linked ionic polymer modified with Cr(III) compounds

AV‐17(Cr) material was prepared by modifying a commercial polymer AV‐17 (initially bearing R4N⁺ functional groups) with Cr(III) compounds was investigated. Comparative isotherms characterizing the and ion sorption from solution with pH values of 3 and 8, respectively, at 19°C and 60°C, were obtained using the raw AV‐17(Cl) and the modified AV‐17(Cr) material. The sorption process on AV‐17(Cr) takes place through the coordination of Cr(VI) ions with Cr(III) ions, while on AV‐17(Cl) it is due to an ion exchange mechanism. The sorption isotherms obtained in pH 8 solutions fit perfectly the Langmuir model. The thermodynamic functions ΔG, ΔH, and ΔS characteristic to the adsorption of ions from K₂CrO₄ solutions with pH = 8 were calculated. The active sites belonging to the AV‐17(Cr) material were identified as jarosite type compounds of Cr(III). SEM images show that the Cr(III) compounds are present in the form of ultrafine particles located on the surface and within the bulk phase of the polymer granules. Comparative thermal degradation process of both the AV‐17(Cr) and the AV‐17(Cl) material was conducted in air and in an inert atmosphere (He). The thermal degradation mechanism of sorbent AV‐17(Cr) and exchanger AV‐17(Cl) is proposed. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41306.     

Cross‐linked chitosan beads for phosphate removal from aqueous solution

Chitosan beads were cross‐linked with glutaraldehyde (GA) and epichlorohydrin (EP), respectively, at variable composition. The general features of the adsorptive and textural properties of the bead systems were characterized using p‐nitrophenolate (PNP) at pH 8.5. As well, a systematic adsorption study of phosphate dianion (phosphate ( ) species was carried out in aqueous solution at pH 8.5 and 295 K. The Sips isotherm model yielded adsorption parameters for the chitosan bead systems: (i) monolayer adsorption capacity (Q_m) for PNP ranged from 0.30 to 0.52 mmol g^?1 and (ii) Q_m values for the bead systems with ranged from 22.4–52.1 mg g^?1 for these conditions. GA cross‐linked beads reveal greater Q_m values for PNP while EP cross‐linked beads showed greater Q_m values for , in accordance with the surface chemistry and the materials design described herein. The EP cross‐linked beads show favorable adsorption–desorption properties and represents a promising tunable adsorbent system for the effective removal of phosphate dianion species in aqueous solution. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42949.     

Preparation and capacitive performances of PEDOT/indigo carmine composite hydrogel

In this article, indigo carmine (IC) was introduced into poly(3,4‐ethylenedioxythiophene)‐poly(styrenesulfonate) (PEDOT‐PSS) hydrogel by in situ polymerization to prepare PEDOT/IC composite hydrogel. The structural characterization of PEDOT/IC composite hydrogel was analyzed by Fourier‐transform infrared spectroscopy (FTIR), UV–vis spectroscopy, X‐Ray diffraction (XRD), and Scanning electron microscopy (SEM). The results indicated that IC was successfully introduced into PEDOT‐PSS hydrogel. Electrochemical performances were investigated by cyclic voltammetry, galvostatic charge‐discharge, and electrochemical impedance technology. The specific capacitance of PEDOT‐PSS hydrogel was efficiently increased by the introduction of IC. The specific capacitance of PEDOT‐PSS hydrogel increased first and then decreased with the increase of the concentration of IC. The specific capacitance of PEDOT‐PSS hydrogel was increased from 38F/g to a maximum value of 123F/g (current density = 0.5 A/g) when the concentration of IC reached 5 mM. On the basis of cycle‐life tests, the capacitance retention of about 68% for the PEDOT/IC composite hydrogel after 5000 cycles suggested a high cycle stability of PEDOT/IC composite hydrogel and its potential as an electrode material for supercapacitor applications. POLYM. COMPOS., 34:989–996, 2013. © 2013 Society of Plastics Engineers     

Effect of Ca2+ induced crosslinking on the mechanical and barrier properties of cast alginate films

The use of alginate as a coating material for packaging applications is currently limited due to its difficult processability and high moisture sensitivity. Therefore, this study addresses the crosslinking and scale‐up to a continuous application. Three different crosslinking agents were applied: CaCl₂ with ethylene diamine tetraacetic acid and two low soluble salts (CaHPO₄ and CaCO₃). Those were incorporated by internal setting in an alginate matrix with varying Ca²⁺ concentration ( ) and ratio. With the addition of Ca²⁺, the tensile strength and elongation at break of the cast alginate films increased. This was optimal for a of 0.010–0.015 g (g alginate)^?1 dependent on the crosslinking agent. The decrease in water vapor and oxygen permeability due to crosslinking was independent of the crosslinking agent. However, the optimal aiming to decrease permeability was different for the crosslinking agents: CaHPO₄ showed best results at a of 0.010 g (g alginate)^?1, CaCl₂ at 0.012 g (g alginate)^?1, and CaCO₃ at 0.027 g (g alginate)^?1. Upon all analyzed properties CaHPO₄ was the most promising crosslinking agent for alginate. Moreover, selected alginate formulations were successfully processed in a continuous lacquering plant. The produced two‐layer systems have very low oxygen permeabilities which can be further reduced by crosslinking. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45754.     

Dispersion polymerization of methyl methacrylate with three types of comblike fluorinated stabilizers in supercritical carbon dioxide

Dispersion polymerizations of methyl methacrylate in supercritical carbon dioxide were conducted with three types of comblike fluorinate polymer stabilizers: poly(3,3,4,4,5,5,6,6,7,7,8,8,9,9,10,10,10‐heptadecafluorodecyl methacrylate) (PHDFDMA), poly(3,3,4,4,5,5,6,6,7,7,8,8,8‐tridecafluorooctyl methacrylate) (PTDFOMA), and poly(2,2,3,3,3‐pentafluoropropyl methacrylate) (PPFPMA). The effect of the polymerization pressure was not significant on the mean diameters of the poly(methyl methacrylate) (PMMA) particles from 20 to 40 MPa. However, the coefficients of variation of the particle diameters produced at 20 MPa ( , where is the number‐basis mean particle diameter), where the heterogeneous phase was found before polymerization, were larger than those produced at 30 and 40 MPa, where the homogeneous phase was found. The mean size of the PMMA obtained with PTDFOMA and PPFPMA strongly depended on the stabilizer concentration compared with that obtained with PHDFDMA. Moreover, the mean size decreased as the carbon dioxide‐philic side chain length increased. As shown by the results of this study, the best stabilizer among the three types of stabilizers for producing PMMA particles was PHDFDMA. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43813.     

Improved processibility of silicone composites by MQ silicone resins

Processibilities of silicone composites were always a problem for their high content of SiO₂ powders. This article found that the substitution of silicone resins for linear polydimethylsiloxanes (PDMS) made processibilities easier. Three silicone resins (MQ1.0, MQ1.1, and MQ1.2) with clarified chemical structures (by FT IR, ²⁹Si NMR, and GPC) were adopted. Their shearing viscosities [η()] were greatly higher than PDMS with higher molecular weight, which could be assigned to stronger molecular interactions as surface tension and flowing activation energy ΔE indicated. On the contrary, η() of MQ‐PDMS binary blends greatly decreased to that even lower than either components (about 85% utmost decrease comparing to PDMS), for the variation of molecular interaction rather than dilution effect. Furtherly, when PDMS were partly replaced with MQ resins, process time of PDMS–SiO₂ silicone composites were greatly shortened (from >6 to 2 h), while with better SiO₂ dispersion (Mooney viscosity greatly decreased from 30.0 to 5.0 MU). Better dispersion of SiO₂ fillers in composites could be confirmed by SEM and mechanical properties. For the better dispersion, mechanical properties of composites were improved with higher elastic modulus, higher tensile strength, and higher hardness, especially with higher elongation at break (utmost increased from 190% to 277%). © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46445.     

Mechanism of internal and external electron donor effects on propylene polymerization with MgCl2‐supported Ziegler–Natta catalyst: New evidences based on active center counting

Two TiCl₄/Di/MgCl₂ type supported Ziegler–Natta catalysts were prepared by loading dibutylphthalate or dicyclopentyldimethoxysilane (DCPDMS) (internal donor, Di) and TiCl₄ on activated δ‐MgCl₂ in sequence, and a blank catalyst was prepared by loading TiCl₄ on the same δ‐MgCl₂ without adding Di. These catalysts have similar specific surface area and pore size distribution, thus form a suitable base for comparative studies. Propylene polymerization with the catalysts was conducted in n‐heptane slurry using triethylaluminum (TEA) as cocatalyst, and the effects of Di as well as De (external donor, in this work it was DCPDMS) on the number of active centers, the distribution of active centers among three polypropylene (PP) fractions (isotactic, medium isotactic, and atactic PP chains), and chain propagation rate constants of the PP fractions were studied by counting the number of active centers in the PP fractions using a method based on selective quench‐labeling of the propagation chains by 2‐thiophenecarbonyl chloride. When De was not added in the polymerization, introducing a phthalate type Di in the catalyst evidently changed the active center distribution by enhancing the proportion of active centers producing isotactic PP (iPP) ( ), but scarcely changed reactivities of the three groups of active centers forming the three fractions. When the De was added in the polymerization system with TiCl₄/phthalate/MgCl₂ catalyst, further shifting of active center distribution in favor of took place, meanwhile reactivities of the three groups of active centers also remarkably changed in favor of . Mutual effects of these changes led to overwhelming dominance of iPP production in the TiCl₄/Di/MgCl₂–TEA/De system (Di = phthalate, De = alkoxysilane). In contrast, though using alkoxysilane as Di also caused shifting of active center distribution in favor of when De was not added, addition of alkoxysilane De caused reverse shifting of active center distribution in favor of those producing PP of lower stereoregularity. This unfavorable change largely counteracted the reactivity changes in favor of caused by the De, rendering the catalytic system rather poor isospecificity. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46605.     

Effect of carbon nanotube dispersion on the complex permittivity and absorption of nanocomposites in 2–18 GHz ranges

The effect of dispersion processes on complex permittivity and microwave absorption in 2?18 GHz ranges is presented for nanocomposites loaded with different amounts of carbon nanotubes (CNTs) ranging from 1 to 5 wt %. The ultrasonic sonication (US) method and the three‐roll mill (TRM) method were performed for the manufacturing of the CNT/epoxy absorbers with different dispersing levels. Microscopic observations revealed that the CNT agglomerates were reduced after the TRM process, and individual CNTs were uniformly dispersed in the epoxy resin. For the same weight content of CNT fillers, the percentage increase of between US and TRM samples varies from 35.5% to 101.7% while the corresponding increment of (dielectric loss) varies from 79.6% to 248.8%. A minimum reflection loss for the US sample with 2 wt % CNTs is only ?7.8 dB at 11.3 GHz while the corresponding TRM sample is greatly improved to reach ?37.4 dB at 7.76 GHz for the same matching thickness of 3 mm. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40963.