Effects of molecular weight and grafted maleic anhydride of functionalized polylactic acid used in reactive compatibilized binary and ternary blends of polylactic acid and thermoplastic cassava starch

Polylactic acid (PLA) was reactively functionalized with maleic anhydride (MA) and 2,5‐bis(tert‐butylperoxy)?2,5‐dimethylhexane (Luperox 101 or L101) using a twin screw extruder (TSE). The effects of functionality (grafted MA level) and/or number average molecular weight of functionalized PLA (PLA‐g‐MA) as the reactive polymer pairs (binary blends) and reactive compatibilizer (ternary blends) were investigated. Due to the dominant side reaction during melt free radical grafting, polymer degradation or chain scission, PLA‐g‐MA having a higher grafted MA had lower molecular weights and intrinsic viscosity as well as broader molecular weight distribution values. The thermal, physical, mechanical, and morphological properties of binary blends produced by using the TSE and injection molding at a ratio of 70 wt % PLA‐g‐MA and 30 wt % thermoplastic cassava starch (TPCS) were analyzed. The reactive blends having grafted MA more than 0.4 wt % had poor tensile strength and elongation at break. Similar trends in morphology and tensile properties were observed in the reactive ternary blends. The use of PLA‐g‐MA strongly impacted the elongation at break but not the modulus or tensile strength. An increase of PLA‐g‐MA's number average molecular weight ( or M_n) improved the tensile properties of the blends. The reactive ternary blend having 0.1 wt % grafted MA on PLA and PLA‐g‐MA basis and PLA‐g‐MA's M_n of 45 kDa offered the highest elongation at break. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42230.     

Melt characteristics,mechanical, and thermal properties of blown film from modified blends of poly(butylene adipate‐co‐terephthalate) and poly(lactide)

Blown films from poly(butylene adipate‐co‐terephthalate) and poly(lactide) (PLA) blends were investigated. The blends were prepared in a twin‐screw extruder, in the presence of small amounts of dicumyl peroxide (DCP). The influence of DCP concentration on film blowing, rheological, mechanical, and thermal properties of the blends is reported in this article. Rheological results showed a marked increase in polymer melt strength and elasticity with the addition of DCP. As a consequence, the film homogeneity and the stability of the bubble were improved. The modified blend films, compared with the unmodified blend, showed an improvement in tensile strength and modulus with a slight loss in elongation. Fourier transform infrared and gel results revealed that chain scission and branching were more significant than crosslinking when the DCP loadings in the blends were not higher than 0.7%. A reduction in melt temperatures of PLA was observed due to difficulty in chain crystallization. The concentrations of DCP strongly affected the melting temperatures but had an insignificant effect on the decomposition behavior of the blends. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

The phase behavior and mechanical properties of polyarylate and polycarbonate blends

The phase behavior and mechanical properties of a series of polyarylate/polycarbonate blends were studied. The polymers are known to transesterify, the extent of which depends upon the thermal and shear history and affects phase behavior and properties. Single screw extrusion, twin screw extrusion, and solution casting were employed for blend preparation. Two transition temperatures, corresponding to a polycarbonate-rich phase and to a polyarylate-rich phase, were seen in blends that were solution cast or compounded in a single screw extruder at 285°C. But after injection molding a single T_g was observed, When annealed at 180°C for several hours the molded blend was found to phase separate. Blends that were compounded in a twin screw extruder exhibited a single T_g and could not be phase separated. The flexural and tensile properties of blends that were prepared in a twin screw extruder show a small positive synergism. But the impact properties were substantially below the rule of mixtures values, probably the result of advanced exchange reaction and thermal degradation.     

Mechanical properties and morphological changes of poly(lactic acid)/polycarbonate/poly(butylene adipate‐co‐terephthalate) blend through reactive processing

The mechanical properties and morphological changes of poly(lactic acid) (PLA), polycarbonate (PC), and poly(butylene adipate‐co‐terephthalate) (PBAT) polymer blends were investigated. Several types of blend samples were prepared by reactive processing (RP) with a twin‐screw extruder using dicumyl peroxide (DCP) as a radical initiator. Dynamic mechanical analyses (DMA) of binary polymer blends of PC/PBAT indicated that each component was miscible over a wide range of PC/PBAT mixing ratios. DMA of PLA/PBAT/PC ternary blends revealed that PBAT is miscible with PC even in the case of ternary blend system and the miscibility of PLA and PBAT can also be modified through RP. As a result, the tensile strain and impact strength of the ternary blends was increased considerably through RP, especially for PLA/PBAT/PC = 42/18/40 (wt/wt/wt) with DCP (0.3 phr). Scanning electron microscopy (SEM) analysis of the PLA/PBAT/PC blends revealed many small spherical island phases with a domain size of approximately 0.05–1 μm for RP, whereas it was approximately 10 μm without RP. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Modification of low‐density polyethylene by graft copolymerization with maleic anhydride and blends with polyamide 6

Modification of low‐density polyethylene (LDPE) hyperbranched grafting with a maleic anhydride (MAH) was carried out using corotating twin screw extruder in the presence of benzoyl peroxide. The LDPE/polyamide 6 (PA6) and LDPE‐g‐MAH/PA6 blends were obtained with a corotating twin screw extruder. The melt viscosity of the grafted LDPE was measured by a capillary rheometer. The grafted copolymer was characterized by Fourier transform infrared spectroscopy and scanning electron microscopy The effects of variations in temperature, PA6 loading, and benzoyl peroxide and MAH concentration were investigated. The results show that most MAH monomers were grafted onto the LDPE at a lower MAH concentration. With the proper selection of the reaction parameters, we obtained a grafting degree higher than 4.9%. Mechanical test results indicate that the blends had good interfacial adhesion and good stability of the phase structure during heating, which was reflected in the mechanical properties. Furthermore, the results reveal that the tensile strength of the blends increased continuously with increasing PA6 content. Moreover, the home‐synthesized maleated LDPE could be used for the compatibilization of LDPE/PA 6 blends. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis and properties of reactively compatibilized polyester and polyamide blends

The functionalization of poly(butylene terephthalate) (PBT) has been accomplished in a twin screw extruder by grafting maleic anhydride (MA) using a free radical polymerization technique. The resulting PBT‐g‐MA was successfully used as a compatibilizer for the binary blends of polyester (PBT) and polyamide (PA66). Enhanced mechanical properties were achieved for the blend containing a small amount (as low as 2.5 %) of PBT‐g‐MA compared to the binary blend of unmodified PBT with PA66. Loss and storage moduli for blends containing compatibilizer were higher than those of uncompatibilized blends or their respective polymers. The grafting and compatibilization reactions were confirmed using FTIR and ¹³C NMR spectroscopy. The properties of these blends were studied in detail by varying the amount of compatibilizer, and the improved mechanical behaviour was correlated with the morphology with the help of scanning electron microscopy. Morphology studies also revealed the interfacial interaction in the blend containing grafted PBT. The improvement in the properties of these blends can be attributed to the effective interaction of grafted maleic anhydride groups with the amino group in PA66. The results indicate that PBT‐g‐MA acts as an effective compatibilizer for the immiscible blends of PBT and PA66. © 2000 Society of Chemical Industry     

Compatibilization of PE/PS and PE/PP blends. I. Effect of processing conditions and formulation

The objective of this work was to study the effectiveness of low‐cost commercial compatibilizers and several processes (internal mixer, single‐ and twin‐screw extruders) for two types of plastic blends: high‐density polyethylene/polypropylene and high‐density polyethylene/polystyrene blends, to gain insight into the recycling of wastes from those frequently encountered mixed plastics. Blends going from a pure A to a pure B component, with and without a compatibilizer, were prepared using an internal mixer, a corotating twin‐screw extruder, as well as a single‐screw extruder to follow an industrial‐convenient process. In both cases, the analyses of blend morphologies highlighted the poor adherence between the two phases in the uncompatibilized blends. Compatibilized blends display better adherence between phases and the ability to process blends made from both single‐ and twin‐screw extruders. When adding a compatibilizer, the viscosity of each blend (PE/PP or PE/PS) increased due to a better adhesion of the phases. Charpy impact tests showed that the presence of the compatibilizer in PE/PS blends increased their impact properties. Indeed, the improvement of the adhesion between the two phases enabled stress transfer at the interface. A single‐screw extruder seems to be efficient as a processing method on an industrial scale when a compatibilizer is used. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2475–2484, 2003     

Melt blending of polylactide and poly(methyl methacrylate): Thermal and mechanical properties and phase morphology characterization

Blends of polylactide with poly(methyl methacrylate), PLA/PMMA, were prepared by a semi‐industrial twin screw extruder and afterwards were injection molded. Blends were studied using different techniques as Fourier Transform Infrared Spectroscopy (FTIR), Dynamic Mechanical Analysis (DMA), Differential Scanning Calorimetry (DSC), Scanning Electron Microscopy (SEM), and mechanical properties by means of tensile and impact tests, were also studied. This work helped better understanding of apparently contradictory results reported in the literature for PLA/PMMA blends prepared by melt compounding. DSC first heating scan and DMA results showed partially miscible blends, whereas the second DSC heating scan showed miscible blends. For miscible blends, T_g values were predicted using Gordon‐Taylor equation. On the other hand, Small and Van Krevelen approaches were used to estimate the solubility parameters of neat PLA and neat PMMA, and Flory‐Huggins interaction parameter was calculated from solubility parameters. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42677.     

Mechanical,thermal, and biodegradability properties of PLA/modified starch blends

Three different kinds of modified starch (MS) were prepared as fillers to assess the compatibility between them and poly(lactic acid) (PLA) resin. The blends were prepared by incorporating 15 wt% of the MS into PLA using a twin‐screw extruder. Through morphology analysis, it can be seen that the dispersion state of MS granules was greatly different. Investigations of thermal behavior indicated that the addition of MS decreased thermal properties which found expression in the decrease of melting temperature and vicat softening temperature (VST). But thermal stability of PLA/maleic anhydride grafted starch (MA‐g‐ST) was slightly higher than those of other blends. PLA/MA‐g‐ST blend exhibited the highest notched impact strength, elongation at break, and tensile strength, which means MA‐g‐ST was suitable as a filler improving the toughness of PLA. It was also proved that biodegradability rate of blends increased dramatically and reached up to 1.80, 1.89, 1.44 g day⁻¹ after 60 days, respectively. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers     

Influences of dicumyl peroxide on morphology and mechanical properties of polypropylene/poly(styrene‐b‐butadiene‐b‐styrene) blends via vane‐extruder

Polypropylene (PP) and poly(styrene‐b‐butadiene‐b‐styrene) block copolymer (SBS) were melt‐blended in the presence of initiator system. Dicumyl peroxide (DCP)/Triallyl isocyanurate (TAIC) via self‐deigned VE, aiming at in situ reactive compatibilization of toughed PP/SBS blend. The reactivity, morphology and mechanical properties of PP/SBS/DCP/TAIC blends were studied. Online torque detection was conducted to monitor changes in viscosities of reactive compatibilized blends, which could give proof of the interfacial grafted reaction induced by DCP/TAIC system. The effect of reactive compatibilization on the dispersed particles sizes and interfacial adhesion was studied by scanning electron microscopy. Analysis on mechanical performance revealed the impact strength improved after treated by initiator system, moreover, the impact‐fractured surface observation showed, the failure mode changed from debonding mechanism of neat 50PP/50SBS blend to plastic deformation mechanism of blend containing 3.0 phr initiator system. With improved interfacial adhesion, compatibilized blends not only were toughened but also exhibited enhanced tensile strength and thermal stability. Dynamic mechanical analysis showed a reduction of between PP phase and the PB segments in SBS phase, indicating reactive compatibilization of the blend was achieved. In the final part, a brief discussion was given about the dominant effects from chain scission of PP matrix to intergrafting reactions of PP and SBS, under different content of DCP/TAIC initiator system. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41543.     

Effects of reactive blending temperature on impact toughness of poly(lactic acid) ternary blends

Reactive blending of poly(lactic acid) (PLA) with an ethylene/n-butyl acrylate/glycidyl methacrylate terpolymer elastomer (EBA-GMA) and a zinc ionomer of ethylene/methacrylic acid copolymer (EMAA-Zn) was performed at various temperatures using a twin screw extruder. Notched Izod impact strength, dynamic mechanical properties and morphological structure of the resulting blends were studied. A sharp brittle–ductile transition (BDT) of the resulting blends occurred when the blending temperature increased to 195～210 °C and the EBA-GMA/EMAA-Zn ratio was equal to or large than 1. The influences of blending temperature on interfacial compatibilization and croslinking of the elastomer were also studied. Supertough PLA ternary blends were achieved by this reactive approach.     

Evaluation of mechanical properties of polypropylene/polycarbonate/SEBS ternary polymer blends using Taguchi experimental analysis

In this work, ternary polymer blends based on polypropylene (PP)/polycarbonate (PC)/poly(styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene) (SEBS) triblock copolymer and a reactive maleic anhydride grafted SEBS (SEBS‐g‐MAH) at fixed compositions are prepared using twin‐screw extruder at different levels of die temperature (235‐245‐255°C), screw speed (70‐100‐130 rpm), and blending sequence (M1‐M2‐M3). In M₁ procedure, all of the components are dry blended and extruded simultaneously using Brabender twin‐screw extruder, whereas in M₂ procedure, PC, SEBS, and SEBS‐g‐MAH minor phases are first preblended in twin‐screw extruder and after granulating are added to PP continuous phase in twin‐screw extruder. Consequently, in M₃ procedure, PP and SEBS‐g‐MAH are first preblended and then are extruded with other components. The influence of these parameters as processing conditions on mechanical properties of PP/PC/SEBS ternary blends is investigated using L9 Taguchi experimental design. The responding variables are impact strength and tensile properties (Young's modulus and yield stress), which are influenced by the morphology of ternary blend, and the results are used to perform the analysis of mean effect as well. It is shown that the resulted morphology, tensile properties, and impact strength are influenced by extrusion variables. Additionally, the optimum processing conditions of ternary PP/PC/SEBS blends were achieved via Taguchi analysis. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Development of biodegradable PLA/PBT nanoblends

Poly(lactic acid)/poly(butylene terephthalate) (PLA/PBT) blends with 3, 5, and 10 wt % of PBT were produced in a twin‐screw extruder, with the addition of ethylene–glycidyl methacrylate copolymer as compatibilizer. An uncompatibilized PLA/PBT blend with 5 wt % of PBT was prepared for comparison studies. The epoxy reactive groups in the compatibilizer allowed modification of the interfacial tension in the blends and reduced the PBT dimensions. The crystallinity of the blends was studied, and its influence on mechanical properties was analyzed. Tensile tests showed an increase in strain at break from 3% for neat PLA to 49% for PLA with 3 wt % PBT, while the tensile modulus dropped from 3.59 GPa to 3.35 GPa for the same samples. Izod results showed a transition from a brittle behavior of PLA to a ductile one for compatibilized blends. These results indicate that the nanometer‐size dispersed phase was effective in changing the deformation behavior of the matrix without a significant loss of modulus. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45951.     

Studies on mechanical and morphological behavior of hybrid nanoclay‐reinforced EPDM‐g‐TMEVS/PS blends

A new copolymer of tris(2‐methoxyethoxy) vinylsilane (TMEVS)‐grafted ethylene–propylene–diene elastomer (EPDM‐g‐TMEVS) has been developed by grafting of TMEVS onto EPDM by using dicumylperoxide (DCP) initiator. The linear polystyrene blends (EPDM‐g‐TMEVS/PS) based on EPDM‐g‐TMEVS have been synthesized with varying weight percentages of polystyrene in a twin‐screw extruder. In a similar manner, the dynamically vulcanized and nanoclay‐reinforced polystyrene blends have also been developed using DCP and organically modified montmorillonite clay separately by means of a twin‐screw extruder. The grafting of TMEVS onto EPDM at allylic position present in the third monomer of EPDM has been confirmed by Fourier Transform infrared spectroscopy. The effect of silane‐grafted EPDM and concentration of nanoclay on mechanical properties of polystyrene blends has been studied as per ASTM standards. The morphological behavior of these blends has been investigated using scanning electron microscope. It was observed that the incorporation of silane‐grafted EPDM enhanced the impact strength and the percentage elongation of linear‐ and dynamically vulcanized blends. However, the values of tensile strength, flexural strength, flexural modulus, and hardness of the blends were found to be decreasing with the increase of silane‐grafted EPDM. In the case of nanoclay‐reinforced polystyrene blends, the values of impact strength, tensile strength, flexural strength, flexural modulus, and hardness were increased with an increase in the concentration of nanoclay. XRD studies have been carried out to confirm the formation of nanoclay‐reinforced EPDM‐g‐TMEVS/PS blends. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Blending of immiscible polymers in a mixing zone of a twin screw extruder—effects of compatibilization

The dependence of the morphology development of physical as well as of reactive compatibilized polypropylene/polyamide 6 (PP/PA6) blends in a mixing zone of a co‐rotating twin screw extruder on blend composition and screw rotational speed was investigated. A special process analytical set‐up based on a co‐rotating twin screw extruder was used, which allowed melt sampling from different positions along the operating extruder in time periods less than 10 seconds. It has been shown that the disperse particle sizes in physical blends depend crucially on the blend composition because of the increasing influence of coalescence with an increasing concentration of the disperse phase. Furthermore, the morphology of physical PP/PA6 blends depends strongly on their rheological properties. In contrast, the influence of the screw rotational speed on the morphology is minor. The resulting particle size in a mixing zone is achieved already after a short screw length. The particle size of compatibilized blends is significantly smaller than in physical blends because of the better conditions for drop break‐up and the suppression of coalescence effects. Due to this, compatibilization has a stronger influence on the blend morphology than a variation of process or rheological conditions with physical blends. Furthermore, the compatibilization leads to a concurrent crystallization of the PA6 phase with the PP phase.     

Influence of the morphology and viscoelasticity on the thermomechanical properties of poly(lactic acid)/thermoplastic polyurethane blends compatibilized with ethylene-ester copolymer

Viscoelastic, interfacial properties, and morphological data were employed to predict the thermal and mechanical properties of compatibilized poly(lactic acid) (PLA)/thermoplastic polyurethane (TPU) blends. The combination of interfacial thickness measured by contact angle and entanglement density determined by dynamical mechanical analysis analyze data was employed to evaluate the mechanical behavior of PLA/TPU blends with and without ethylene-butyl acrylate-glycidyl methacrylate (EBG) compatibilization agent. The PLA/TPU blend (70/30 wt %) was prepared in a Haake internal mixer at 190 °C and compatibilized with different contents of EBG. The evaluation of the interfacial properties revealed an increase in the interfacial layer thickness of the PLA/TPU blend with EBG. The scanning electronic microscopy images showed a drastic reduction in the size of the dispersed phase by increasing the compatibilizer agent EBG content in the blend. The compatibilization of the PLA/TPU blends improved both the Izod impact strength and yield stress by 38 and 33%, respectively, in comparison with neat PLA/TPU blend. The addition of EBG into PLA/TPU blends significantly increased the entanglement density and the PLA toughening but resulted in a decrease of PLA deformation at break. The PLA and TPU glass transitions were affected by the EBG, suggesting that the PLA and TPU domains were partially miscible. © 2020 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48926.     

Preparation of polypropylene/acrylonitrile–styrene copolymer alloys by one‐step reactive blending

The compatibilization of polypropylene/acrylonitrile–styrene (PP/AS) blends through the addition of peroxide (DCP) was investigated in this study. The grafting reaction between PP and AS with the addition of peroxide occurred during the reactive‐blending process. The in situ‐formed grafting copolymers of PP‐g‐AS and AS‐g‐PP were then characterized by FTIR. The optimum concentration of the initiator, DCP, was 0.2 wt %, and the reaction temperature should be above 195°C. It was found that, when AS was the major component of the blends, the grafting of AS onto PP was the main process; conversely, when PP was the major component, PP was grafted onto AS. These results can be explained by the main‐chain scission of PP during the reactive‐blending process. With increase of the AS component, the total degree of grafting increased at first and then decreased after the composition of the blends reached 50/50. The maximum degree of grafting was found to be 6 wt % for the 50/50 PP/AS/DCP blend. PP was more degradable than was AS in the presence of peroxide at high temperatures. The MFR values of the PP/AS/DCP blends were slightly greater than were those of the simple PP/AS blends, which means that blending is an effective way to protect PP from degradation. SEM micrographs of the cross section of PP/AS/DCP showed a fine dispersion and a smaller domain size of the dispersed‐phase particles, implying that the in situ‐formed grafting copolymers act as a compatibilizer to reduce the interfacial tension between the PP and AS phases. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 1284–1290, 2001     

Effects of glycerol and PE‐g‐MA on morphology,thermal and tensile properties of LDPE and rice starch blends

The effects of glycerol and polyethylene‐grafted maleic anhydride (PE‐g‐MA) on the morphology, thermal properties, and tensile properties of low‐density polyethylene (LDPE) and rice starch blends were studied by scanning electron microscopy (SEM), differential scanning calorimetry, and the Instron Universal Testing Machine, respectively. Blends of LDPE/rice starch, LDPE/rice starch/glycerol, and LDPE/rice starch/glycerol/PE‐g‐MA with different starch contents were prepared by using a laboratory scale twin‐screw extruder. The distribution of rice starch in LDPE matrix became homogenous after the addition of glycerol. The interfacial adhesion between rice starch and LDPE was improved by the addition of PE‐g‐MA as demonstrated by SEM. The crystallization temperatures of LDPE/rice starch/glycerol blends and LDPE/rice starch/glycerol/PE‐g‐MA blends were similar to that of pure LDPE but higher than that of LDPE/rice starch blends. Both the tensile strength and the elongation at break followed the order of rice starch/LDPE/glycerol/PE‐g‐MA blends > rice starch/LDPE/glycerol > LDPE/rice starch blends. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 344–350, 2004     

Morphological study of LLDPE‐NR reactive blending with maleic anhydride

A binary blend and ternary reactive blends of 90/10 LLDPE/NR using maleic anhydride (MA) as a reactive agent with and without dicumyl peroxide (DCP) were made at 150°C in an internal mixer. The fracture surfaces of the blends were conventionally observed by TEM and atomic force microscope, revealing that the rubber domains became smaller with the addition of MA and DCP. This suggested that the in situ graft copolymer (LLDPE‐g‐NR) was formed and acted as an in situ compatibilizer to enhance interfacial adhesion. This was further supported by FTIR results. Importantly, after removal of NR phase from the blends, the remaining LLDPE part was dissolved in hot xylene, purified by precipitation in methanol, and carefully prepared by solvent casting for TEM observation. The microstructures of the solvent‐extracted LLDPE from all blends are unlike that of solvent cast‐ pure LLDPE, which shows only crystalline structure. This leads to an unambiguous way to disclose the existence of an in situ graft copolymer. The solvent‐extracted LLDPE from the blends shows mixed morphology of LLDPE crystalline structure and its in situ graft copolymer as nanofibrillar networks of the NR phase protruded from the amorphous region of the LLDPE matrix due to spinodal decomposition by the solvent removal. Adding MA makes more branches and fibril connections of the NR phase, whereas a thinner fibril network and more links of the NR and the LLDPE amorphous region are found in the reactive blend with MA and DCP, where the most compatibilized blend is obtained. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Effect of composition and processing conditions on the chemical and morphological evolution of PA‐6/EPM/ EPM‐g‐MA blends in a corotating twin‐screw extruder

This study investigated the effect of blend composition and processing conditions on the chemical conversion and morphological evolution of PA‐6/EPM/EPM‐g‐MA blends along a twin‐screw extruder. The maleic anhydride (MA) content of the modified rubber was found to decrease strongly, to a level of almost zero, and in the melting zone the particle size was dramatically reduced, from millimeters to submicrometers. Blend composition had a secondary effect on both chemical conversion and morphological development. The processing conditions, particularly the temperature profile and the screw speed, affected both the chemical conversion and the morphological evolution. Using low temperatures and low screw rotation it was possible to follow in detail the evolution of morphological development of a reactive blend in a twin‐screw extruder. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 1535–1546, 2001