The role of the ratio (PEG:PPG) of a triblock copolymer (PPG‐b‐PEG‐b‐PPG) in the cure kinetics,miscibility and thermal and mechanical properties in an epoxy matrix

The aim of this study was to evaluate the role of different poly(ethylene glycol):poly(propylene glycol) (PEG:PPG) molar ratios in a triblock copolymer in the cure kinetics, miscibility and thermal and mechanical properties in an epoxy matrix. The poly(propylene glycol)‐block‐poly(ethylene glycol)‐block‐poly(propylene glycol) (PPG‐b‐PEG‐b‐PPG) triblock copolymers used had two different molecular masses: 3300 and 2000 g mol^?1. The mass concentration of PEG in the copolymer structure played a key role in the miscibility and cure kinetics of the blend as well as in the thermal–mechanical properties. Phase separation was observed only for blends formed with the 3300 g mol^?1 triblock copolymer at 20 wt%. Concerning thermal properties, the miscibility of the copolymer in the epoxy matrix reduced the T_g value by 13 °C, although a 62% increase in fracture toughness (K_IC) was observed. After the addition of PPG‐b‐PEG‐b‐PPG with 3300 g mol^?1 there was a reduction in the modulus of elasticity by 8% compared to the neat matrix; no significant changes were observed in T_g values for the immiscible system. The use of PPG‐b‐PEG‐b‐PPG with 2000 g mol^?1 reduced the modulus of elasticity by approximately 47% and increased toughness (K_IC) up to 43%. Finally, for the curing kinetics of all materials, the incorporation of the triblock copolymer PPG‐b‐PEG‐b‐PPG delayed the cure reaction of the DGEBA/DDM (DGEBA, diglycidyl ether of bisphenol A; DDM, Q3‐4,4′‐Diaminodiphenylmethane) system when there is miscibility and accelerated the cure reaction when it is immiscible. All experimental curing reactions could be fitted to the Kamal autocatalytic model presenting an excellent agreement with experimental data. This model was able to capture some interesting features of the addition of triblock copolymers in an epoxy resin. © 2018 Society of Chemical Industry     

Dynamic mechanical and shape memory properties of copolymers based on o‐allylphenol type benzoxazines and diglycidyl ether of bisphenol‐A

Three benzoxazines based on o‐allylphenol and 1,6‐hexamethylenediamine (HDA) or 4,4′‐diaminodiphenyl methane (DDM) or 4,4′‐diaminodiphenyl ether (DDE) were respectively blended with diglycidyl ether of bisphenol‐A (DGEBA) in various weight ratios followed by thermal polymerization to prepare three series of benzoxazine/DGEBA copolymers. With increasing DGEBA content, the peak temperature of the exothermic peaks in the DSC curves shows a systematic increase for the three series of benzoxazine/DGEBA blends. Each copolymer shows a single glass transition temperature (T_g). As the content of DGEBA is increased, T_g reaches a minimum for the copolymer system based on HDA but a maximum for the two systems based on DDM and DDE. For the same benzoxazine/DGEBA weight ratio, copolymers based on DDM and DDE show high T_g values over those based on HDA. The three series of benzoxazine/DGEBA copolymers exhibit a one‐way dual shape memory effect based on T_g, and the shape memory properties of the copolymers under tensile deformation mode vary with the variation of both diamine bridge structure and DGEBA content. © 2018 Society of Chemical Industry     

Synthesis and characterization of poly(ε‐caprolactone)‐b‐poly(ethylene glycol)‐b‐poly(ε‐caprolactone) triblock copolymers with dibutylmagnesium as catalyst

Two series of poly(ε‐caprolactone)‐b‐poly(ethylene glycol)‐b‐poly(ε‐caprolactone) triblock copolymers were prepared by the ring opening polymerization of ε‐caprolactone in the presence of poly(ethylene glycol) and dibutylmagnesium in 1,4‐dioxane solution at 70°C. The triblock structure and molecular weight of the copolymers were analyzed and confirmed by ¹H NMR, ¹³C NMR, FTIR, and gel permeation chromatography. The crystallization and thermal properties of the copolymers were investigated by wide‐angle X‐ray diffraction (WAXD) and differential scanning calorimetry (DSC). The results illustrated that the crystallization and melting behaviors of the copolymers were depended on the copolymer composition and the relative length of each block in copolymers. Crystallization exothermal peaks (T_c) and melting endothermic peaks (T_m) of PEG block were significantly influenced by the relative length of PCL blocks, due to the hindrance of the lateral PCL blocks. With increasing of the length of PCL blocks, the diffraction and the melting peak of PEG block disappeared gradually in the WAXD patterns and DSC curves, respectively. In contrast, the crystallization of PCL blocks was not suppressed by the middle PEG block. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Amphiphilic diblock copolymers poly(2‐hydroxyethylmethacrylate)‐b‐(N‐phenylmaleimide) and poly(2‐hydroxyethylmethacrylate)‐b‐(styrene) using the macroinitiator poly(HEMA)‐Cl by ATRP: Preparation,characterization, and thermal properties

In recent years, much attention has been given to the development of specialty polymers from useful materials. In this context, amphiphilic block copolymers were prepared by atom transfer radical polymerization (ATRP) of N‐phenylmaleimide (N‐PhMI) or styrene using a poly(2‐hydroxyethylmethacrylate)‐Cl macroinitiator/CuBr/bipyridine initiating system. The macroinitiator P(HEMA)‐Cl was directly prepared in toluene by reverse ATRP using BPO/FeCl₃ 6 H₂O/PPh₃ as initiating system. The microstructure of the block copolymers were characterized using FTIR, ¹H‐NMR, ¹³C‐NMR spectroscopic techniques and scanning electron microscopy (SEM). The thermal behavior was studied by differential scanning calorimetry (DSC), and thermogravimetry (TG). The theoretical number average molecular weight (M_n,th) was calculated from the feed capacity. The microphotographs of the film's surfaces show that the film's top surfaces were generally smooth. The TDT of the block copolymer P(HEMA)₈₀‐b‐P(N‐PhMI)₂₀ and P(HEMA)₉₀‐b‐P(St)₁₀ of about 290°C was also lower than that found for the macroi′nitiator poly(HEMA)‐Cl. The block copolymers exhibited only one T_g before thermal decomposition, which could be attributed to the low molar content of the N‐PhMI or St blocks respectively. This result also indicates that the phase behavior of the copolymers is predominately determined by the HEMA block. The curves reveal that the polymers show phase transition behavior of amorphous polymers. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Preparation,characterization, and metal ion retention capacity of Co(II) and Ni(II) from poly(p‐HO‐ and p‐Cl‐phenylmaleimide‐co‐2‐hydroxypropylmethacrylate) using the ultra filtration technique

p‐Chlorophenylmaleimide and p‐hydroxyphenylmaleimide with 2‐hydroxypropyl methacrylate were synthesized by radical polymerization, and the metal ion retention capacity and thermal behavior of the copolymers were evaluated. The copolymers were obtained by solution radical polymerization with a 0.50 : 0.50 feed monomer ratio. The maximum retention capacity (MRC) for the removal of two metal ions, Co(II) and Ni(II) in aqueous phase were determined using the liquid‐phase polymer based retention technique. Inorganic ion interactions with the hydrophilic polymer were determined as a function of pH. The metal ion retention capacity does not depend strongly on the pH. Metal ion retention increased with an increase of pH for a copolymer composition 0.50 : 0.50. At different pH, the MRC of the poly(p‐chlorophenylmaleimide‐co‐2‐hydroxypropylmethacrylate) for Co(II) and Ni(II) ions varied from 44.1 to 48.6 mg/g and from 41.5 mg/g to 46.0 mg/g, respectively; while the MRC of poly(p‐hydroxyphenylmaleimide‐co‐2‐hydroxypropyl methacrylate) for Co(II) and Ni(II) ions varied from 28.4 to 35.6 mg/g and from 27.2 to 30.8 mg/g, respectively. The copolymers and copolymer–metal complexes were characterized by elemental analysis, FT‐IR, ¹H NMR spectroscopy, and thermal behavior. The thermal behavior of the copolymer and polymer–metal complexes were studied using differential scanning calorimetry and thermogravimetry techniques under nitrogen atmosphere. The thermal decomposition temperature and T_g were influenced by the binding‐metal ion on the copolymer. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Preparation of 4‐(4‐hydroxyphenoxy)phenol diglycidyl ether with improved toughness behavior

A high‐performance difunctional epoxy resin, 4‐(4‐hydroxyphenoxy)phenol diglycidyl ether (DHPOP), was synthesized by a two‐step method. The curing behavior of DHPOP was investigated by nonisothermal differential scanning calorimetry method and the curing kinetics results revealed that the introduction of ether linkage could improve the activity of epoxy groups, leading to a lower curing temperature and apparent activation energy compared with that of the commercial bisphenol‐A diglycidyl ether (DGEBA). A series of copolymers were then prepared by varying the mass ratio of DHPOP and DGEBA, which were cured with 4,4′‐diaminodiphenyl methane. The effect of DHPOP contents on thermal and mechanical properties and fracture morphology was studied. As expected, with the increase of DHPOP in the network, the impact strength and char yield were significantly enhanced, while the glass transition temperature (T_g) remained unchanged because of the increase of crosslink density. The excellent toughness endows the DHPOP with the promising potential for the application as high‐performance resin matrix. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46458.     

Dielectric properties of lithium‐perchlorate‐filled acrylonitrile–hexyl methacrylate copolymer films

A series of poly(acrylonitrile‐co‐hexyl methacrylate), PAN‐co‐PHMA, copolymers with various hexyl methacrylate (HMA) contents were synthesized by emulsion technique. The incorporation of HMA units into the copolymers was confirmed by Fourier transform infrared and proton nuclear magnetic resonance (¹H‐NMR) spectroscopy. Glass transition temperatures (T _g) and thermal decomposition temperatures of copolymers were determined by differential scanning calorimetry and thermogravimetric analysis. The T _g of copolymers were lowered monotonically by increasing HMA content, while thermal stabilities of copolymers were enhanced. The frequency dependence of dielectric properties of three different amounts of LiClO₄ salt doped copolymer films was investigated. The influence of molar fraction of HMA on dielectric constant and ac‐conductivity of copolymer films was examined. Samples with higher HMA contents showed better stability and conductivity, as a result of increase in free volume and the mobility of the dipoles. The ac conductivity of copolymers was also improved by increasing LiClO₄ salt which was due to the existence of more charge carriers. PAN(88)‐co‐PHMA(12) copolymer with 1.5 mol% of lithium salt exhibited ionic conductivity of the 7.8 × 10⁻⁴ S/cm at 298 K. POLYM. COMPOS., 38:1792–1799, 2017. © 2015 Society of Plastics Engineers     

Preparation,characterization, and thermal properties of polystyrene‐block‐quaternized poly(4‐vinylpyridine)/Montmorillonite nanocomposites

Polystyrene‐block‐poly(4‐vinylpyridine) (PS‐b‐P4VP) was synthesized by two steps of reversible addition‐fragmentation transfer (RAFT) polymerization of styrene (St) and 4‐vinylpyridine (4VP) successively. After P4VP block was quaternized with CH₃I, PS‐b‐quaternized P4VP/montmorillonite (PS‐b‐QP4VP/MMT) nanocomposites were prepared by cationic exchange reactions of quaternary ammonium ion in the PS‐b‐QP4VP with ions in MMT. The results obtained from X‐ray diffraction (XRD) and transmission electron microscopy (TEM) images demonstrate that the block copolymer/MMT nanocomposites are of intercalated and exfoliated structures, and also a small amount of silicates' layers remained in the original structure; differential scanning calorimetry (DSC) and thermal gravimetric analysis (TGA) results show that the nanocomposites displayed higher glass transition temperature (T_g) and higher thermal stability than that of the corresponding copolymers. The blending of PS‐b‐QP4VP/MMT with commercial PS makes MMT to be further separated, and the MMT was homogeneously dispersed in the polymer matrix. The enhancement of thermal stability of PS/PS‐b‐QP4VP/MMT is about 20°C in comparison with commercial PS. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:1950–1958, 2006     

A study on thermal behavior of a poly(VDF‐CTFE) copolymers binder for high energy materials

This article describes a study on thermal behavior of poly(vinylidene fluoride‐chlorotrifluoroetheylene) [poly(VDF‐CTFE)] copolymers as polymeric binders of specific interest for high energy materials (HEMs) composites by thermal analytical techniques. The non‐isothermal thermogravimetry (TG) for poly (VDF‐CTFE) copolymers was recorded in air and N₂ atmospheres. The results of TG thermograms show that poly(VDF‐CTFE) copolymers get degrade at lower temperature when in air than in N₂ atmosphere. In the derivative curve, there was single maximum degradation peak (T_max) indicating one‐stage degradation of poly(VDF‐CTFE) copolymers for all the samples. The other thermal properties such as glass transition temperature (T_g) and degradation temperature (T_d) for poly(VDF‐CTFE) copolymers were measured by employing differential scanning calorimeter (DSC) technique. The kinetic parameters related to thermal degradation of poly(VDF‐CTFE) copolymers were investigated through non‐isothermal Kissinger kinetic method using DSC method. The activation energies for thermal degradation of poly(VDF‐CTFE) copolymers were found in a range of 218–278 kJ/mol. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Segmented copolymers of uniform tetra‐amide units and poly(phenylene oxide) by direct coupling

Segmented copolymers with telechelic poly(2,6‐dimethyl‐1,4‐phenylene ether) (PPE) segments and crystallizable bisester tetra‐amide units (two‐and‐a‐half repeating unit of nylon‐6,T) were studied. The copolymers were synthesized by reacting bifunctional PPE with hydroxylic end groups with an average molecular weight of 3500 g/mol and bisester tetra‐amide units via an ester polycondensation reaction. The bisester tetra‐amide units had phenolic ester groups. By replacing part of the bisester tetra‐amide units with diphenyl terephthalate units (DPT), the concentration of tetra‐amide units in the copolymer was varied from 0 to 11 wt%. Polymers were also prepared from bifunctional PPE, DPT, and a diaminediamide (6T6‐diamine). The thermal and thermal mechanical properties were studied by DSC and DMA and compared with a copolymer with flexible spacer groups between the PPE and the T6T6T. The copolymers had a high T_g of 180–200°C and a melting temperature that increased with amide content of 220–265°C. The melting temperature was sharp with monodisperse amide segments. The T_m – T_c was 39°C, which suggests a fast, but not very fast, crystallization. The crystallinity of the amide was ～ 20%. The copolymers are semicrystalline materials with a high T_g and a high T_g/T_m ratio (> 0.8). © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 512–518, 2007     

Aliphatic–aromatic poly(butylene carbonate‐co‐terephthalate) random copolymers: Synthesis,cocrystallization, and composition‐dependent properties

A series of aliphatic–aromatic poly(carbonate‐co‐ester)s poly(butylene carbonate‐co‐terephthalate)s (PBCTs), with weight‐average molecular weight of 113,000 to 146,000 g/mol, were synthesized from dimethyl carbonate, dimethyl terephthalate, and 1,4‐butanediol via a two‐step polycondensation process using tetrabutyl titanate as the catalyst. The PBCTs, being statistically random copolymers, show a single T_g over the entire composition range. The thermal stability of PBCTs strongly depends on the molar composition. Melting temperatures vary from 113 to 213°C for copolymers with butylene terephthalate (BT) unit content higher than 40 mol %. The copolymers have a eutectic melting point when about 10 mol % BT units are included. Crystal lattice structure shifts from the poly(butylene carbonate) to the poly(butylene terephthalate) type crystal phase with increasing BT unit content. DSC and WAXD results indicate that the PBCT copolymers show isodimorphic cocrystallization. The tensile modulus and strength decrease first and then increase according to copolymer composition. The enzymatic degradation of the PBCT copolymers was also studied. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41952.     

Synthesis of amphiphilic pseudopolyamino acid‐containing ABC‐triblock copolymers and micellar characterizations

This study describes the synthesis of amphiphilic ABC‐triblock copolymers comprising a central pseudopoly(4‐hydroxy‐L ‐proline) segment and terminal hydrophilic poly(ethylene glycol)methyl ether as well as hydrophobic poly(ε‐caprolactone) blocks. Differential scanning calorimetry, ¹H‐NMR spectroscopy, and gel permeation chromatography are used to characterize the copolymers. The thermal properties (T_g and T_ms) of the triblock copolymers depend on the composition of polymers. Larger amounts of ε‐CL incorporated into the macromolecular backbone increased T_g and T_ms. Fluorescence spectroscopy, transmission electron microscopy, and dynamic light scattering are utilized to investigate their micellar characteristics in the aqueous phase. Observations showed a higher critical micelle concentration with higher hydrophilic components in the copolymers. The micelle exhibited a core‐shell‐corona and/or vesicle shape, and the average size was less than 300 nm. Drug entrapment efficiency and drug loading of micelles depending on the composition of block polymers are also described. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis and properties of ethylene‐substituted styrene copolymers

The copolymerization of ethylene and substituted styrenes [RSt's; p‐methylstyrene (MSt), p‐tert‐butylstyrene (BSt), 2‐vinylnaphthalene (VN), and p‐(tert‐butyldimethylsilyloxy)styrene (BMSiOSt)] were investigated with dimethylsilylene(tetramethylcyclopentadienyl)(N‐tert‐butyl)titanium dichloride to yield the corresponding ethylene–RSt copolymers. The substituent on the styrene (St) monomers did not affect the monomer reactivity ratio. The effect of the substituent structure of RSt on the thermal and mechanical properties was studied with differential scanning calorimetry, dynamic mechanical thermal spectroscopy, and elongation testing. The glass‐transition temperature (T_g) of the copolymers increased with increasing RSt content, and the order of T_g was as follows: BSt > VN > MSt = St. A copolymer with p‐hydroxystyrene (HOSt) was successively synthesized by means of deprotection of the copolymer with BMSiOSt. The copolymer showed a much higher T_g than the other copolymers because of the hydrogen connection of its OH groups. The mechanical properties of the copolymer in the glass state, at a lower temperature than T_g, were almost independent of the nature of the RSt. The substituent of the St monomers affected the pattern of the stress–strain curve in the elongation testing in the amorphous state. An improvement in the shape memory effect was observed in poly(ethylene‐co‐BSt). © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

PEG 400/Paraffin oil non‐aqueous emulsions stabilized by PBut‐Block‐P2VP block copolymers

For the preparation of PEG 400 in paraffin oil non‐aqueous biocompatible emulsions, the stabilization efficiency was compared for two well‐defined poly(butadiene)‐block‐poly(2‐vinylpyridine) (PBut‐block‐P2VP) block copolymers, with similar molecular weights but different compositions. The PBut₁₂₈‐block‐P2VP₅₀ and PBut₁₈₉‐block‐P2VP₃₇ samples, designated as copolymer A and B, respectively, are self‐organized in paraffin oil as micelles with a P2VP core and a PBut corona. The PEG 400/paraffin oil emulsion characteristics were determined as a function of the copolymers concentrations and phase ratios. Higher static and shear stabilities were obtained for emulsions stabilized by copolymer B than for those obtained in the presence of copolymer A . A further difference concerns the droplet size, relative viscosity, and loss modulus values obtained at a given dispersed phase volume fraction. At constant copolymer concentrations, it appeared that copolymer B , with a longer PBut sequence, is a more efficient emulsifier and stabilizer than copolymer A . © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41390.     

Effect of processing conditions on physical properties of 3‐aminophenoxyphthalonitrile/epoxy laminates

To develop high performances of polymer composite laminates, differential scanning calorimetry and dynamic rheological analysis studies were conducted to show curing behaviors of 3‐aminophenoxyphthalonitrile/epoxy resin (3‐APN/EP) matrix and define cure parameters of manufacturing processes. Glass fiber reinforced 3‐APN/EP (GF/3‐APN/EP) composite laminates were successfully prepared through different processing conditions with three parameters such as pressures, temperatures, and time. Based on flexure tests, dynamic mechanical analysis, thermal gravimetric analysis, and scanning electron microscope, the complementary catalytic effect of the three processing parameters is investigated by studying mechanical behavior, thermomechanical behavior, thermal behavior, and fracture morphology of GF/3‐APN/EP laminates. The 50/50 GF/3‐APN/EP laminates showed a significant improvement in flexural strength, glass transition temperature (T_g), and thermal stability with favorable processing parameters. It was also found that the T_g and thermal stability were significantly improved by the postheated treatment method. The effect of manufacturing process provides a new and simple route for the polymer–matrix composites application, which indicates that the composites can be manufactured at low temperatures. But, they can be used in a high temperature environment. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39746.     

Synthesis and characterization of hydrophilic copolymers of maleimide derivatives with 2‐hydroxyethyl methacrylate: electrochemical and thermal behavior

BACKGROUND: The high‐technology industries have been the driving force in the development of new synthetic polymers that combine thermal stability with specific functional properties. In this study p‐chlorophenylmaleimide, p‐hydroxyphenylmaleimide and p‐nitrophenylmaleimide (R‐PhMI) with 2‐hydroxyethyl methacrylate (HEMA) were synthesized by free radical polymerization to obtain hydrophilic polymers, in order to study the effect of the p‐chloroaryl, p‐hydroxyaryl or p‐nitroaryl group on the copolymer composition, electrochemical behavior and thermal properties. RESULTS: The thermal behavior was correlated with the copolymer composition and functional groups, maleimide derivatives, on the copolymers. Thermal decomposition temperature (TDT) and glass transition temperature (T_g) were influenced by the functional groups of R‐PhMI moiety on the copolymer. The polymers showed an electrochemically irreversible reduction process under the conditions tested. CONCLUSION: Poly[(p‐chloromaleimide)‐co‐(2‐hydroxyethyl methacrylate)] copolymer shows a higher TDT than poly[(p‐hydroxymaleimide)‐co‐(2‐hydroxyethyl methacrylate)] or poly[(p‐nitromaleimide)‐co‐(2‐hydroxyethyl methacrylate)] (NPHE). T_g decreases in going from nitro to hydroxyl to chloro groups. The NPHE copolymer shows a lower stability, losing weight at 200 °C. The NPHE copolymer shows a well‐defined reduction wave which is similar to those of the other copolymers and it also shows an additional quasi‐reversible reduction wave corresponding to the nitrobenzene group. Copyright © 2009 Society of Chemical Industry     

Synthesis,properties and thermal stability of water‐soluble poly(potassium 1‐hydroxyacrylate‐co‐styrene) copolymer

The present work investigates the structure properties of copolymers using thermogravimetric analysis, hot stage microscopy, static light scattering, field emission scanning electron microscopy, X‐ray diffraction analysis and a Brookfield viscometer. Poly(potassium 1‐hydroxyacrylate) (PKHA) is a water‐soluble polymer. However, the copolymer of styrene and 2‐isopropyl‐5‐methylene‐1,3‐dioxolan‐4‐one is not water soluble at equal molar ratio because the polystyrene reduces the solubility. The effect of styrene on poly(potassium 1‐hydroxyacrylate‐co‐styrene) copolymer, i.e. poly(KHA‐co‐St), was investigated for the increasing solubility of the copolymer. The solubility was increased at a lower molar ratio of styrene such as 0.4 in the copolymer. It was found that the copolymer was soluble in water when a content ratio of 68/32 mol% of homopolymer was incorporated in poly(KHA₆₈‐co‐St₃₂) copolymer as determined by NMR analysis. Also the poly(KHA₆₈‐co‐St₃₂) copolymer was found to be salt tolerant, possessed water absorption capacity and was thermally stable up to 183 °C. Moreover, it is shown that the polystyrene content plays a key role in the thermal stability of the copolymer. © 2017 Society of Chemical Industry     

Characterization and CO2 sorption properties of poly[methacryloxypropylheptacyclopentyl‐T8‐silsesquioxane‐ co‐3‐methacryloxypropyltris(trimethylsiloxy)silane]

Poly[methacryloxypropylheptacyclopentyl‐T8‐silsesquioxane (MAPOSS)‐co‐3‐methacryloxypropyltris(trimethylsiloxy)silane (SiMA)] was synthesized through free radical polymerization. The physical and carbon dioxide (CO₂) sorption properties of the copolymer membranes were investigated in terms of the MAPOSS content. As the MAPOSS content increases, the membrane density increased, suggesting a decrease in the fractional free volume. In addition, the thermal stability was improved with increasing the MAPOSS content. These are because of the polyhedraloligomericilsesquioxane (POSS) units that restrict the high mobility of poly(SiMA) segments. The glass transition temperature, T_g of the copolymers was single T_g based on the differential scanning calorimetry, suggesting that the copolymers were random and not phase separation. Based on the CO₂ sorption measurement, the POSS units play a role in reducing Henry's dissolution by suppressing the mobility of the poly(SiMA) component, while POSS units increase the nonequilibrium excess free volume, which contributes to the Langmuir dissolution. Based on these results, the introduction of MAPOSS unit is one of the effective ways to improved the thermal stability and CO₂ sorption property due to the enhancement of the polymer rigidity. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Synthesis,characterization, reactivity ratios by nuclear magnetic resonance spectroscopy,and application of (2,5‐Dichlorophenyl acrylate‐co‐glycidyl methacrylate) polymers as adhesives for the leather industry

2,5‐ Dichlorophenyl acrylate (DPA)‐co‐glycidyl methacrylate (GMA) polymers having five different compositions were synthesized in 1,4‐dioxane using benzoyl peroxide as a free‐radical initiator at 70 ± 0.5°C. Using ¹H‐NMR spectroscopy, the composition of the two monomers in the copolymers was calculated by comparing the integral values of the aromatic and aliphatic proton peaks. The reactivity ratios were calculated by Fineman–Ross (r₁ = 0.31 and r₂ = 1.08), Kelen–Tudos (r₁ = 0.40 and r₂ = 1.15), and extended Kelen–Tudos (r₁ = 0.39 and r₂ = 1.16) methods. The nonlinear error‐in‐variables model was used to compare the reactivity ratios. The copolymers were characterized by ¹H and proton decoupled ¹³C‐NMR spectroscopes. Gel permeation chromatography was performed for estimating the M_w and M_n and M_w/M_n of the poly(DPA) and copolymers (DPA‐co‐GMA: 09 : 91 and 50 : 50). Thermal stability of the homo‐ and copolymers was estimated using TGA [poly(DPA) > DPA‐co‐GMA (50 : 50) > DPA‐co‐GMA (09:91)], while DSC was utilized for determining the glass transition temperature. T_g increased with increased DPA content in the copolymer. The 50 : 50 mol % copolymer was chosen for curing with diethanolamine in chloroform. The cured resins were tested for the adhesive properties on leather at different temperatures (50, 90, 100, and 110°C). The resin cured at 50 °C exhibited a maximum peel strength of 1.6 N/mm, revealing a good adhesive behavior. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1167–1174, 2006     

Synthesis and characterization of the novel block copolymer poly(ε‐caprolactone)‐b‐poly(4‐vinyl pyridine) by the combination of coordination and controlled free‐radical polymerizations

A novel block copolymer, poly(ε‐caprolactone)‐b‐poly(4‐vinyl pyridine), was synthesized with a bifunctional initiator strategy. Poly(ε‐caprolactone) prepolymer with a 2,2,6,6‐tetramethylpiperidinyloxy (TEMPO) end group (PCL_T) was first obtained by coordination polymerization, which showed a controlled mechanism in the process. By means of ultraviolet spectroscopy and electron spin resonance spectroscopy, the TEMPO moiety was determined to be intact in the polymerization. The copolymers were then obtained by the controlled radical polymerization of 4‐vinyl pyridine in the presence of PCL_T. The desired block copolymers were characterized by gel permeation chromatography, Fourier transform infrared spectroscopy, and NMR spectroscopy in detail. Also, the effects of the molecular weight and concentration of PCL_T on the copolymerization were investigated. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 2280–2285, 2004