Dielectric properties of irradiated polymer/multiwalled carbon nanotube and its amino functionalized form

The polymer/multiwalled carbon nanotube [poly(vinyl alcohol) (PVA)/carboxyethyl acrylate (CEA)]‐multiwalled carbon nanotube (MWCNT) and its amino functionalized (PVA/CEA)‐MWCNT‐NH₂ nanocomposite samples were successfully synthesized by the chemical method in the form of films. The samples were irradiated with gamma‐ray doses of 50 and 100 kGy and with ion beam fluence of 2.5 × 10¹⁸ and 3.75 × 10¹⁸ ions cm^?2. The prepared nanocomposite samples were characterized using X‐ray diffraction and thermogravimetric analysis. The X‐ray diffraction and thermogravimetric analysis confirm the existence of the chemical crosslinking occurred in the polymer compositions. The AC electrical conductivity, electrical modulus, dielectric constant, and dielectric loss in the frequency range 10²–10⁶ Hz are measured at room temperature. The electrical conductivity is increased with MWCNT doping, gamma‐irradiation, and by ion beam irradiation. A comprehensive analysis of the results revealed that dielectric properties are improved due to the induced physicochemical changes and conductive networks induced by ion beam irradiation. The behavioral effect of these embedded nanoparticles in a PVA matrix on the microstructural, dielectric, and electric properties is analyzed for possible device applications. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46647.     

Synthesis of high‐density polyethylene/rGO‐CNT‐Fe nanocomposites with outstanding magnetic and electrical properties

Semi‐conducting polyethylene (PE) nanocomposites with outstanding magnetic properties at room temperature were synthesized. These exceptional properties, for a diamagnetic and insulating matrix as PE, were obtained by polymerizing ethylene in the presence of a catalytic system formed by a metallocene catalyst supported on a mixture of reduced graphene oxide (rGO) and carbon nanotubes with encapsulated iron (CNT‐Fe). It was used a constant and very low amount of CNT‐Fe, obtained by vapor chemical deposition using ferrocene. The percolation threshold, to achieve conductivity, was obtained using a variable amount of rGO. The nanocomposites were semiconductors with the addition of 2.8 wt % and 6.0 wt % of the filler, with electrical conductivities of 4.99 × 10^?6 S cm^?1 and 7.29 × 10^?4 S cm^?1, respectively. Very high coercivity values of 890–980 Oe at room temperature were achieved by the presence of only 0.04–0.06 wt % of iron in the nanocomposites. The novelty of this work is the production of a thermoplastic with both, magnetic and electric properties at room temperature, by the use of two fillers, that is rGO and CNT‐Fe. The use of a small amount of CNT‐Fe to produce the magnetic properties and variable amount of rGO to introduce the electrical conductivity in PE matrix let to balance both properties. The encapsulation strategy used to obtain Fe in CNT, protect Fe from easy oxidation and aggregation. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 45382.     

Reduction of percolation threshold through double percolation in melt‐blended polycarbonate/acrylonitrile butadiene styrene/multiwall carbon nanotubes elastomer nanocomposites

We demonstrate a method that involves melt blending of polycarbonate (PC) and melt‐blended acrylonitrile butadiene styrene (ABS) with multiwall carbon nanotubes (MWCNTs) to prepare electrically conducting PC/MWCNT nanocomposites at significantly low MWCNT loading. The partial solubility of ABS in PC led to a selective dispersion of the MWCNTs in the ABS phase after melt‐blending PC and ABS. Thus, a sudden rise in electrical conductivity (∼10⁸ orders of magnitude) of the nanocomposites was found at 0.328 vol% of MWCNT, which was explained in terms of double percolation phenomena. By optimizing the ratio of PC and the ABS–MWCNT mixture, an electrical conductivity of 5.58 × 10⁻⁵ and 7.23 × 10⁻³ S cm⁻¹ was achieved in the nanocomposites with MWCNT loading as low as 0.458 and 1.188 vol%, respectively. Transmission electron microscopy revealed a good dispersion and distribution of the MWCNTs in the ABS phase, leading to the formation of continuous MWCNT network structure throughout the matrix even at very low MWCNT loading. Storage modulus and thermal stability of the PC were also increased by the presence of a small amount of MWCNTs in the nanocomposites.POLYM. COMPOS., 2013. © 2013 Society of Plastics Engineers     

Electrical and mechanical properties of acrylonitrile‐butadiene‐styrene/multiwall carbon nanotube nanocomposites prepared by melt‐blending

The electrical properties in polymer/carbon nanotube (CNT) nanocomposites are governed not only by the degree of dispersion but also to a greater extent on the aspect ratio of the CNTs in the final composites. Melt‐mixing of polymer and CNTs at high shear rate usually breaks the CNTS that lowers the aspect ratio of the nanotubes. Thus, homogeneous dispersion of CNTs while retaining the aspect ratio is a major challenge in melt‐mixing. Here, we demonstrate a novel method that involves melt‐blending of acrylonitrile‐butadiene‐styrene (ABS) and in situ polymerized polystyrene (PS)/multiwalled CNT (MWCNT) nanocomposites, to prepare electrically conducting ABS/MWCNT nanocomposites with very low CNT loading than reported. The rationale behind choosing PS/MWCNT as blending component was that ABS is reported to form miscible blend with the PS. Thus, (80/20 w/w) ABS/(PS/MWCNT) nanocomposites obtained by melt‐blending showed electrical conductivity value ≈1.27 × 10^?6 S cm^?1 at MWCNT loading close to 0.64 wt %, which is quite lower than previously reported value for ABS/MWCNT system prepared via solution blending. Scanning electron microscopy and differential scanning calorimetry analysis indicated the formation of homogenous and miscible blend of ABS and PS. The high temperature (100°C) storage modulus of ABS (1298 MPa) in the nanocomposites was increased to 1696 MPa in presence of 0.64 wt % of the MWCNT. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Low percolation threshold and high electrical conductivity in melt‐blended polycarbonate/multiwall carbon nanotube nanocomposites in the presence of poly(ε‐caprolactone)

This study focuses on the electrical properties of polycarbonate (PC)/poly(ε‐caprolactone) (PCL)‐multiwall carbon nanotube (MWCNT) nanocomposites. MWCNTs were incorporated into thermoplastic PC matrix by simple melt blending using biodegradable PCL based concentrates with MWCNT loadings (3.5 wt%). Because of the lower interfacial energy between MWCNT and PCL, the nanotubes remain in their excellent dispersion state into matrix polymer. Thus, electrical percolation in PC/PCL‐MWCNT nanocomposites was obtained at lower MWCNT loading rather than direct incorporation of MWCNT into PC matrix. AC and DC electrical conductivity of miscible PC/PCL‐MWCNT nanocomposites were studied in a broad frequency range, 10¹?10⁶ Hz and resulted in low percolation threshold (p_c) of 0.14 wt%, and the critical exponent (t) of 2.09 from the scaling law equation. The plot of logσ_DC versus p^?1/3 showed linear variation and indicated the existence of tunneling conduction among MWCNTs. At low MWCNT loading, the influence of large polymeric gaps between conducting clusters is the reason for the frequency dependent electrical conductivity. Transmission electron microscopy and field emission scanning electron microscopy showed that MWCNTs were homogeneously dispersed and developed a continuous interconnected network path throughout the matrix phase and miscibility behavior of the polymer blend. POLYM. ENG. SCI., 54:646–659, 2014. © 2013 Society of Plastics Engineers     

Effect of MWNTs concentration and cooling rate on the morphological,structural, and electrical properties of non‐isothermally crystallized PEN/MWNT nanocomposites

The effect of multiwall carbon nanotubes (MWNT) concentration and cooling rate on the morphological, structural and electrical properties of non‐isothermally crystallized Poly(ethylene naphthalate) nanocomposites (PEN/MWNT) was studied. PEN/MWNT nanocomposites containing 1 and 2 wt % of nanotubes were prepared by melt blending in a mini twin screw extruder. Nanocomposite samples with different degree of crystallinity (X_c) were obtained via non‐isothermally crystallization at cooling rates of 2, 10, 20, and 300°C min^?1. In this study it was demonstrated that carbon nanotubes and cooling rate strongly influence morphological and structural characteristics of PEN. Calorimetric results showed that the peak crystallization temperature (T_c) of PEN nanocomposites was increased ～9° through heterogeneous nucleation with respect to pure PEN. X‐ray diffraction revealed that carbon nanotubes modify the crystalline structure of PEN favoring the formation of β‐crystals, and this effect increases with the nanotubes content. On the basis of X‐ray scattering analysis, the variation of lamellar thickness revealed that nanotubes promote the formation of lamellar crystals with average thickness of 20 nm at different cooling rates. These structural and morphological changes play an important role on the electrical properties of nanocomposites. It was found that higher concentration of nanotubes and crystallinity promotes electrical conductivity of nanocomposites in the order of semiconductors (until 1 × 10^?4 S cm^?1) as well as permittivity of 20 at different tested frequencies. This may due to the interconnected networks of nanotubes throughout the crystalline structure formed in PEN nanocomposites. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41765.     

Preparation and characterization of proton exchange membrane based on polyphosphoric acid modified by PVDF‐HFP

A polyphosphoric acid functionalized proton exchange membrane (PEM) was prepared by a ring opening reaction using the epoxycyclohexylethyltrimethoxysilane (EHTMS) and amino trimethylene phosphonic acid (ATMP) as raw materials and was modified by poly(vinylidene fluoride)–hexafluoro propylene (PVDF‐HFP). The structure of the membranes was characterized by Fourier transform infrared and scanning electron microscopy. The X‐ray photoelectron spectroscopy explores the content of the elements in the membrane related to the ion exchange capacity value. The membranes’ properties including water uptake, swelling ratio, proton conductivity, and hydrolysis stability were studied. Performance tests show that when ATMP/EHTMS = 1/5, conductivity of the PVDF‐HFP modified PEMs increased from 0.83 × 10^?4 S cm^?1 at 20 °C to 9.53 × 10^?3 S cm^?1 at 160 °C, the swelling ratio of membranes decreased from 2.71% to 2.13%. The results indicate that the introduction of F atoms is beneficial to increase the proton conductivity and the dimensional stability. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46737.     

A facile route to develop electrical conductivity with minimum possible multi‐wall carbon nanotube (MWCNT) loading in poly(methyl methacrylate)/MWCNT nanocomposites

Today, we stand at the threshold of exploring carbon nanotube (CNT) based conducting polymer nanocomposites as a new paradigm for the next generation multifunctional materials. However, irrespective of the reported methods of composite preparation, the use of CNTs in most polymer matrices to date has been limited by challenges in processing and insufficient dispersability of CNTs without chemical functionalization. Thus, development of an industrially feasible process for preparation of polymer/CNT conducting nanocomposites at very low CNT loading is essential prior to the commercialization of polymer/CNT nanocomposites. Here, we demonstrate a process technology that involves in situ bulk polymerization of methyl methacrylate monomer in the presence of multi‐wall carbon nanotubes (MWCNTs) and commercial poly(methyl methacrylate) (PMMA) beads, for the preparation of PMMA/MWCNT conducting nanocomposites with significantly lower (0.12 wt% MWCNT) percolation threshold than ever reported with unmodified commercial CNTs of similar qualities. Thus, a conductivity of 4.71 × 10^?5 and 2.04 × 10^?3 S cm^?1 was achieved in the PMMA/MWCNT nanocomposites through a homogeneous dispersion of 0.2 and 0.4 wt% CNT, respectively, selectively in the in situ polymerized PMMA region by using 70 wt% PMMA beads during the polymerization. At a constant CNT loading, the conductivity of the composites was increased with increasing weight percentage of PMMA beads, indicating the formation of a more continuous network structure of the CNTs in the PMMA matrix. Scanning and transmission electron microscopy studies revealed the dispersion of MWCNTs selectively in the in situ polymerized PMMA phase of the nanocomposites. Copyright © 2012 Society of Chemical Industry     

Electrical conductivity behavior of epoxy matrix nanocomposites with simultaneous dispersion of carbon nanotubes and clays

In this work, nanocomposites with simultaneous dispersion of multiwalled carbon nanotubes (MWCNT) and montmorillonite clays in an epoxy matrix were prepared by in situ polymerization. A high energy sonication was employed as the dispersion method, without the aid of solvents in the process. The simultaneous dispersion of clays with carbon nanotubes (CNT) in different polymeric matrices has shown a synergic potential of increasing mechanical properties and electrical conductivity. Two different montmorillonite clays were used: a natural (MMT‐Na⁺) and an organoclay (MMT‐30B). The nanocomposites had their electrical conductivity (σ) and dielectric constant (ε_r) measured by impedance spectroscopy. The sharp increase in electrical conductivity was found between 0.10 and 0.25 wt% of the MWCNTs. Transmission electron microscopy (TEM) of the samples showed a lower tendency of MWCNT segregation on the MMT‐30B clay surface, which is connected to intercalation/exfoliation in the matrix, that generates less free volume available for MWCNTs in the epoxy matrix. Data from electrical measurement showed that simultaneously adding organoclay reduces the electrical conduction in the nanocomposite. Moreover, conductivity and permittivity dispersion in low frequency suggest agglomeration of nanotubes surrounding the natural clay (MMT‐Na⁺) particles, which is confirmed by TEM. POLYM. COMPOS., 37:1603–1611, 2016. © 2014 Society of Plastics Engineers     

Low percolation threshold in polycarbonate/multiwalled carbon nanotubes nanocomposites through melt blending with poly(butylene terephthalate)

Here, we demonstrate an easy method for the preparation of highly electrically conductive polycarbonate (PC)/multiwalled carbon nanotubes (MWCNTs) nanocomposites in the presence of poly(butylene terephthalate) (PBT). In the presence of MWCNTs, PC and PBT formed a miscible blend, and the MWCNTs in the PC matrix were uniformly and homogeneously dispersed after the melt mixing of the PC and PBT–MWCNT mixture. Finally, when the proportion of the PC and PBT–MWCNT mixture in the blend/MWCNT nanocomposites was changed, an electrical conductivity of 6.87 × 10^?7 S/cm was obtained in the PC/PBT–MWCNT nanocomposites at an MWCNT loading as low as about 0.35 wt %. Transmission electron microscopy revealed a regular and homogeneous dispersion and distribution of the MWCNTs and formed a continuous conductive network pathway of MWCNTs throughout the matrix phase. The storage modulus and thermal stability of the PC were also enhanced by the presence of a small amount of MWCNTs in the nanocomposites. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Electrically conductive nanocomposites of polyaniline with poly(vinyl alcohol) and methylcellulose

Electrically conductive nanocomposites of HCl‐doped polyaniline (PANI–HCl) nanocolloid particles with water‐soluble and film‐forming polymers such as poly(vinyl alcohol) (PVA) and methylcellulose (MC) were prepared by the redispersion of preformed MC‐coated submicrometric PANI–HCl particles in PVA and MC solutions under sonication for 1 h and the casting of the films from the dispersions followed by drying. The submicrometric polyaniline (PANI) particles were prepared by the oxidative dispersion polymerization of aniline in an acidic (1.25M HCl) aqueous ethanol (30 : 70) medium with MC as a steric stabilizer. The particles contained 4.7 wt % MC and had a conductivity of 7.4 S/cm. They had an oblong shape of 203 nm (length) and 137 nm (breadth). Sonication broke the oblong‐shaped particles to sizes of ～10 nm in the PVA matrix and ～60 nm in the MC matrix. The electrical conductivity of these films was measured, and the percolation threshold was determined. The composites had the characteristics of a low percolation threshold at a volume fraction of PANI of 2.5 × 10^?2 in the PVA matrix and at a volume fraction of 3.7 × 10^?2 in the MC matrix. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Quaternized polysulfone‐based nanocomposite membranes and improved properties by intercalated layered double hydroxide

Two anions (dodecylbenzenesulfonate anion and stearate anion) are employed to synthesize intercalated layered double hydroxides (LDH) by co‐precipitation method. Then the intercalated LDHs are incorporated in the casting solutions of chloromethylated polysulfone (CMPSF) for fabricating quaternized polysulfone/LDH nanocomposite membranes. Fourier transform infrared, X‐ray diffraction, thermogravimetric analysis, scanning electron microscopy, and mastersizer laser particle size analysis are used to characterize the structure and morphology of LDHs and membranes. The properties of the composite membranes including water uptake, mechanical property, thermal stability, and ionic conductivity are investigated. Compared with other anion exchange membranes, both nanocomposite membranes containing 5% LDH sheets displayed better balanced performance. They exhibit the ionic conductivity of 3.58 × 10^?2 S cm^?1 and 3.86 × 10^?2 S cm^?1 at 60°C, respectively. POLYM. ENG. SCI., 2017. © 2017 Society of Plastics Engineers     

The role of a biobased epoxy monomer in the preparation of diglycidyl ether of bisphenol A/MWCNT composites

A biobased epoxy monomer (GA‐II) derived from gallic acid for multiwalls carbon nanotubes’ (MWCNTs) dispersion improvement is reported in this article. The aromatic group in its molecular structure made it to be absorbed onto the surface of MWCNTs via π‐π interactions and the GA‐II anchored MWCNT could be homogeneously dispersed in DGEBA matrix via sonication. That was proved by Raman and UV spectroscopy as well as scanning electron microscope. After curing reaction, the epoxy/MWCNT composites demonstrated enhanced mechanical properties, excellent thermal conductivity, and high electrical conductivity. With the addition of only 0.5 wt% GA‐II modified MWCNT, the tensile strength, tensile modulus, flexural strength, and flexural modulus of the composites were improved by 28%, 40%, 22%, and 16%, respectively. The thermal and electrical conductivities were also improved from 0.15 to 0.25 W/m K (67% increased) and from 0.7 × 10⁻¹⁴ to 0.24 × 10⁻⁴ S cm⁻¹ (10 orders increased). POLYM. COMPOS., 38:1640–1645, 2017. © 2015 Society of Plastics Engineers     

Effect of nanoparticle shape on the conductivity of Ag nanoparticle poly(vinyl alcohol) composite films

In this work, the shape effect of silver nanoparticles (AgNPs) on photocatalysis and electrical conductivity was investigated. Different shapes of AgNPs achieved using various concentrations of NaBH₄ were characterized using particle size analysis, UV–visible spectroscopy and high‐resolution transmission electron microscopy. The colours of colloidal solutions were found to be influenced by the shape of the nanoparticles. Yellow and blue AgNPs were spherical and triangular in shape, respectively, whereas distorted spherical particles showed a red colour and the presence of both particles in one solution resulted in a green colloidal solution. The AgNPs were used to prepare Ag/poly(vinyl alcohol) (PVA) composite films and their electrical conductivity was investigated. Owing to their better charge carrier generation, uniform distribution in the PVA matrix and enhanced surface plasmon resonance, blue AgNPs (triangular shaped) exhibited superior conductivity performance compared to the other nanoparticles. The values for maximum conductivity for the blue and yellow AgNPs were 3.45 × 10^?4 Ω^?1 cm^?1 and 2.67 × 10^?4 Ω^?1 cm^?1respectively. © 2019 Society of Chemical Industry     

Solid polymer electrolyte based on waterborne polyurethane for all‐solid‐state lithium ion batteries

A series of solid polymer electrolytes (SPEs) based on comb‐like nonionic waterborne polyurethane (NWPU) and LiClO₄ are fabricated via a solvent free process. The NWPU‐based SPEs have sufficient mechanical strength which is beneficial to their dimensional stability. Differential scanning calorimetry analysis indicates that the phase separation occurs by the addition of the lithium salt. Scanning electron microscopy and X‐ray diffraction analyses illustrate the good compatibility between LiClO₄ and NWPU. Fourier transform infrared study reveals the complicated interactions among lithium ions with the amide, carbonyl and ether groups in such SPEs. AC impedance spectroscopy shows the conductivity of the SPEs exhibiting a linear Arrhenius relationship with temperature. The ionic conductivity of the SPE with the mass content of 15% LiClO₄ (SPE15) can reach 5.44 × 10^?6 S cm^?1 at 40 °C and 2.35 ×10^?3 S cm^?1 at 140 °C. The SPE15 possesses a wide electrochemical stability window of 0–5 V (vs. Li+/Li) and thermal stability at 140 °C. The excellent properties of this new NWPU‐based SPE are a promising solid electrolyte candidate for all‐solid‐state lithium ion batteries. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 45554.     

Dispersion of multiwalled carbon nanotubes in polyacrylonitrile‐co‐starch copolymer matrix for enhancement of electrical,thermal, and gas barrier properties

Nanomaterials gained great importance on account of their wide range of applications in many areas. Carbon nanotubes (CNTs) exhibit exceptional electrical, thermal, gas barrier, and tensile properties and can therefore be used for the development of a new generation of composite materials. Functionalized multiwalled carbon nanotubes (MWCNTs) reinforced Polyacrylonitrile‐co‐starch nanocomposites were prepared by in situ polymerization technique. The structural property of PAN‐co‐starch/MWCNT nanocomposites was studied by X‐ray diffraction, scanning electron microscopy, and transmission electron microscopy. The conductivity, tensile strength, and thermal properties of nanocomposites were measured as a function of MWCNT concentrations. The thermal stability, conductivity, and tensile strength of PAN‐co‐starch/MWCNT nanocomposites were improved with increasing concentration of MWCNTs. Oxygen barrier property of PAN‐co‐starch/MWCNT nanocomposites was calculated and it was found that, the property was reduced substantially with increase of MWCNTs proportion. The synthesized PAN‐co‐starch/MWCNT nanocomposites may used for electrostatically dissipative materials, aerospace or sporting goods, and electronic materials. © 2013 Society of Plastics Engineers     

Development and Characterisation of Electrically Conductive Polymeric‐Based Blends for Proton Exchange Membrane Fuel Cell Bipolar Plates

The main objective of this work was to develop films with controlled dimensions for proton exchange membrane fuel cell (PEMFC) bipolar plates (BPPs) using the twin‐screw extrusion process. These films consisted of a low‐viscosity polyethylene terephthalate (PET) in which a mixture of high specific surface area carbon black (CB) and synthetic flake graphite (GR) were dispersed. A third conductive additive, consisting of silver‐coated glass particles (SCG) or multi‐walled carbon nanotubes (MWCNT), was also added at a low concentration (5 wt.‐%) in order to study its synergistic effect on the PET‐based blend electrical conductivity. As the developed blends had to meet properties suitable for PEMFC bipolar plate applications, they were characterised for their electrical through‐plane resistivity, mechanical properties and oxygen permeability. Through‐plane electrical resistivity of about 0.3 Ω·cm and oxygen permeation rate of 3.5 × 10^–8 cc cm^–2 s^–1 were obtained for only 30 wt.‐% of a 60:40 mixture of CB/GR conductive additives. Although the substitution of 5 wt.‐% of CB/GR by the same amount of MWCNT had no significant effect on BPPs' electrical resistivity, it helped to improve their mechanical properties and especially their oxygen permeation, which was decreased from 3.5 × 10^–8 cc cm^–2 s^–1 to around 0.6 × 10^–8 cc cm^–2 s^–1.     

Thermosetting polyurethane multiwalled carbon nanotube composites

Thermosetting polyurethane (PU) multi‐walled carbon nanotube (MWCNT) nanocomposites at loadings up to 1 wt % were prepared via an addition polymerization reaction. The morphology of the nanocomposites and degree of dispersion of the MWCNTs was studied using a combination of scanning electron microscopy (SEM), high resolution transmission electron microscopy (HRTEM) and wide angle X‐ray diffraction (WAXD), and revealed the nanotubes to be highly dispersed in the PU matrix. Addition of just 0.1 wt % MWCNTs resulted in significant enhancements in stiffness, strength and toughness. Increases in Young's modulus, % elongation at break and ultimate tensile strength of 561, 302 and 397% were measured for the nanocomposites compared to the unfilled PU. The effect of the MWCNTs on the modulus of the PU was evaluated using the Rule of Mixtures, Krenchel and Halpin‐Tsai models. Only the Halpin‐Tsai model applied to high aspect ratio nanotubes was in good agreement with the modulus values determined experimentally. Strong interfacial shear stress was found between PU chains and nanotubes, up to 439 MPa, calculated using a modified Kelly‐Tyson model. Evidence for strong interfacial interactions was obtained from the Raman spectra of both the precursor materials and nanocomposites. When the MWCNTs were added to the isophorone diisocyanate an up‐shift of 14 cm^?1 and on average 40 cm^?1 was obtained for the position of the carbon‐hydrogen (C? H) out‐of plane bending (766 cm^?1) and isocyanate symmetric stretch (1420 cm^?1) modes respectively. Moreover, an up‐shift of 24 cm^?1 was recorded for the nanotube tangential mode (G‐band) for the 1.0 wt % nanocomposite because of the compressive forces of the PU matrix acting on the MWCNTs. The dynamic mechanical (DMA) properties of the PU thermoset and the nanocomposites were measured as a function of temperature. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Improving the electrical conductivity of ethylene 1‐octene copolymer/cyclic olefin copolymer immiscible blends by interfacial localization of MWCNTs

The localization of multiwall carbon nanotubes (MWCNTs) in the immiscible blends of ethylene–1‐octene copolymer (EOC) and cyclic olefin copolymer (COC) with the sea–island morphology and electrical conductivity of resulting nanocomposites were investigated. Depending on the feeding orders, as the MWCNTs were located in the COC droplet, the electrical conductivity was obtained as high as 5.71 × 10^?7 S/cm, while the MWCNTs were located in EOC/COC interface, the electrical conductivity increased significantly up to 1.72 × 10^?2 S/cm. The improved electrical conductivity in EOE/COC/MWCNTs nanocomposite is attributed to the interfacial localization of MWCNTs which is resulted from thermodynamic affinity of MWCNTs to COC, as well as an interconnected structure via deformed and swelled COC droplets. Thermodynamic affinity of MWCNTs to COC and established interconnected structure are confirmed by rheological characterization, microscopic observations, dynamic mechanical analysis, and electrical conductivity measurements. Therefore, as a result of selective localization of MWCNTs and well‐designed phase morphology, lower rheological and especially electrical percolation thresholds could be obtained in the ternary nanocomposites compared to the binary systems. POLYM. ENG. SCI., 59:447–456, 2019. © 2018 Society of Plastics Engineers     

Biopolymer agar‐agar doped with NH4SCN as solid polymer electrolyte for electrochemical cell application

A new polymer electrolyte based on the biopolymer Agar‐Agar doped with ammonium thiocyanate (NH₄SCN) has been prepared and characterized by FTIR analysis, X‐ray diffraction measurements, AC impedance spectroscopy, transference number measurements, and DSC analysis. The Fourier transform infrared analysis confirms the complex formation between agar and NH₄SCN. The amorphous nature of the polymer electrolyte has been revealed from X‐ray diffraction analysis. The highest ionic conductivity has been observed for the sample of composition 1:1 between Agar and NH₄SCN. As a function of temperature, the ionic conductivity of this sample exhibits Arrhenius behavior increasing from 1.03 × 10^?3 S cm^?1 at ambient temperature to 3.16 × 10^?3 S cm^?1 at 343 K. The transference number has been estimated by the dc polarization method, and it has been proven that the conducting species are predominantly cations. Using the highest conductivity polymer electrolyte, solid state electrochemical cell has been fabricated and cell parameters are reported. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 44702.