Evaluation of interfacial properties and microfailure mechanisms in single fiber‐reinforced epoxy composites at low temperature

In this preliminary study, micromechanical techniques were used to compare the interfacial properties of both carbon and glass fiber composites with two structurally different epoxy matrices (YD‐114 and YDF‐175) at ambient and relatively low temperatures (25°C and −10°C). Tensile modulus of elasticity for both epoxies was higher at lower temperature. Although both fibers exhibited more bimodality at lower temperature than at ambient temperature, glass fiber composites exhibited a statistically greater improvement in tensile strength. This may be attributed to differences in inherent flaws and rigidity. A decrement in stress was observed for YDF‐175 epoxy composites under cyclic loadings at both temperatures, which was attributed to lower interfacial shear strength (IFSS). In contrast to the IFSS of conventional YD‐114 epoxy composites, the IFSS of both the carbon and glass fibers/YDF‐175 epoxy composites studied was higher at the lower temperature. The microfailure pattern observed in microdroplet pullout tests was consistent with the other IFSS results. POLYM. COMPOS., 2012. © 2011 Society of Plastics Engineers     

Interfacial shear strength in carbon fiber‐reinforced poly(phthalazinone ether ketone) composites

We studied interfacial shear strength (IFSS) in carbon fiber (CF)‐reinforced poly (phthalazinone ether ketone) (PPEK) composites system, with emphasis on the influence of forming temperature of composite and sizing agent on CFs. To obtain apparent IFSS of CF‐reinforced PPEK composites shaped at various forming temperatures ranged from 20 up to 370°C, microbond test was carried out at single‐fiber composites. Results of microbond test showed that apparent IFSS was directly proportional to the difference between the matrix solidification temperature (forming temperature) and the test temperature and approximately 80% of the apparent IFSS in CF/PPEK composite system was attributed to residual radial compressive stress at the fiber/matrix interface. By sizing CF with sizing agent, the wettability of the fiber by the matrix was improved and the final apparent IFSS was also improved. POLYM. COMPOS., 34:1921–1926, 2013. © 2013 Society of Plastics Engineers     

Covalent functionalization of carbon fiber with poly(acrylamide) by reversible addition–fragmentation chain transfer polymerization for improving carbon fiber/epoxy interface

A novel method was developed for grafting poly(acrylamide) (PAAM) on to the carbon fiber (CF) surface via reversible addition–fragmentation chain transfer (RAFT) polymerization to improve the interaction between carbon fibers and epoxy matrix in the composites system. The carbon fibers were first treated with nitric acid and γ‐methacryloxypropyltrimethoxy silane (KH570). Then, the PAAM was grafting onto the carbon fiber surface via RAFT polymerization. The resulted carbon fibers functionalized with PAAM (CF‐PAAM) were characterized by FTIR, XPS, and TGA, and the results revealed that CF‐PAAM were synthesized successfully. The introduction of PAAM chains could make the fiber surface rougher and introduce a large numbers of –NH₂ groups, which can improve the interfacial adhesion in the composites. The microbond test results showed that the interfacial shear strength (IFSS) of the composites reinforced by CF‐PAAM has been enhanced about 107%. POLYM. COMPOS., 38:27–31, 2017. © 2015 Society of Plastics Engineers     

Improvement of interfacial properties of carbon fiber‐reinforced poly(phthalazinone ether ketone) composites by introducing carbon nanotube to the interphase

This article aims to improve interfacial properties of carbon fiber‐reinforced poly(phthalazinone ether ketone) (PPEK) composites by means of preparing carbon nanotube (CNT)/carbon fiber hybrid fiber. XPS was used to characterize the chemical structure of unsized carbon fiber and SEM was used to observe the surface topography of carbon fibers. Specific area measurement, dynamic contact angle, and interfacial shear strength (IFSS) testing were performed to examine the effect of CNT on the interfacial properties of carbon fiber/PPEK composites. By the introduction of CNT to the interphase of carbon fiber‐reinforced PPEK composites, an enhancement of IFSS by 55.52% was achieved. Meanwhile, the interfacial fracture topography was also observed and the reinforcing mechanism was discussed. POLYM. COMPOS., 36:26–33, 2015. © 2014 Society of Plastics Engineers     

The effect of ambient moisture and temperature conditions on the mechanical properties of glass fiber/carbon fiber/nylon 6 sandwich hybrid composites consisting of skin‐core morphologies

The concept of skin‐core (SC) morphology was used to make sandwich hybrid composites in which the skin and core were composed of different fibers in the same matrix. The sandwich blends comprising glass skin with carbon core and vice versa were compared with those of the hybrid composite, while the respective carbon (CF) and glass fiber (GF) composites served as points of reference. The composites were compounded and fabricated into injection molded tensile specimens and 3‐mm thick plaques. The effect of ambient temperature and moisture was studied. The fracture mechanical characterization of the various materials was done by using notched compact tension (CT) specimens. Tensile properties were also used to characterize the composites. Morphogical studies based on scanning electron microscopy and light microscopy were used to elucidate fracture characteristics. Deterioration of properties was noticed under hot and humid conditions. Synergism in flexural properties was observed in the CF/GF/PA hybrid composite. The mechanical properties of the CF/GF/PA hybrid are closer to those of CF/PA, suggesting a cost advantage by substituting half of the carbon fibers with glass fibers. Dynamic mechanical analysis results revealed that synergism in T_g is attained by blending or sandwiching glass and carbon fibers. Morphological studies reaffirmed the skin‐core morphology of the composites. POLYM. COMPOS., 26:52–59, 2005. © 2004 Society of Plastics Engineers.     

Flexural properties of S‐2 glass and TR30S carbon fiber‐reinforced epoxy hybrid composites

A study on the flexural properties of hybrid composites reinforced by S‐2 glass and TR30S carbon fibers is presented in this article. Test specimens were made by the hand lay‐up process in an intraply configuration with varying numbers of glass/epoxy laminas substituted for carbon/epoxy laminas. These specimens were then tested in the three point bend configuration in accordance with ASTM D790‐07 at a span to depth ratio of 32. The failed specimens were examined under an optical microscope, and the results show that the dominant failure mode is at the compressive side. The flexural behavior was also simulated by finite element analysis (FEA). Based on the FEA results, the flexural modulus and flexural strength were calculated. Good agreement is found between the experiments and FEA. It is shown that flexural modulus decreases with increasing percentage of S‐2 glass fibers, positive hybrid effects exist by substituting carbon fibers for glass fibers, and applying a thin layer of S‐2 glass fiber‐reinforced polymer on the compressive surface yields the highest flexural strength. The modeling approach presented will pave a way to the effective design of hybrid composites. POLYM. COMPOS., © 2012 Society of Plastics Engineers     

Modifying the carbon fiber–epoxy matrix interphase with graphite nanoplatelets

In this study, a novel method consisting of coating carbon fibers (CF) with graphite nanoplatelets (GnP) is investigated for its ability to modify the mechanical properties in the interphase region. Coating the CF was achieved by immersing CF in a solution of GnP dispersed in an epoxy‐based solution for a few seconds. The influence of the processing conditions on the properties of the coating (thickness, homogeneity, quality of the GnP dispersion) is reported. Interfacial adhesion and the associated failure modes were evaluated by the single fiber fragmentation test. The maximum value of interfacial shear strength (IFSS) was achieved when a relative GnP concentration of 7.9 wt% on CFs, which led to 45 and 34% improvements in IFSS in comparison with the non‐coated CF and epoxy coated CF, respectively. POLYM. COMPOS., 37:1549–1556, 2016. © 2014 Society of Plastics Engineers     

Synthesis of glass fiber‐multiwall carbon nanotube hybrid structures for high‐performance conductive composites

The conductive polyamide 66 (PA66)/carbon nanotube (CNT) composites reinforced with glass fiber‐multiwall CNT (GF‐MWCNT) hybrids were prepared by melt mixing. Electrostactic adsorption was utilized for the deposition of MWCNTs on the surfaces of glass fibers (GFs) to construct hybrid reinforcement with high‐electrical conductivity. The fabricated PA66/CNT composites reinforced with GF‐MWCNT hybrids showed enhanced electrical conductivity and mechanical properties as compared to those of PA66/CNT or PA66/GF/CNT composites. A significant reduction in percolation threshold was found for PA66/GF‐MWCNT/CNT composite (only 0.70 vol%). The morphological investigation demonstrated that MWCNT coating on the surfaces of the GFs improved load transfer between the GFs and the matrix. The presence of MWCNTs in the matrix‐rich interfacial regions enhanced the tensile modulus of the composite by about 10% than that of PA66/GF/CNT composite at the same CNT loading, which shows a promising route to build up high‐performance conductive composites. POLYM. COMPOS. 34:1313–1320, 2013. © 2013 Society of Plastics Engineers     

Experimental evaluation of the interfacial properties of carbon nanotube coated carbon fiber reinforced hybrid composites

A floating catalyst chemical vapor deposition (CVD) unit was utilized to grow CNT onto the surface of carbon fiber (CF). The surface morphology of the resultant fibers, CNT population density and alignment pattern were found to be depended on the CNT growth temperature, growth time, and atmospheric conditions within the CVD chamber. In contrast to the neat‐CF reinforced composites, improved interfacial shear strength (IFSS) between CF and matrix were obtained when the surface of CF was coated by CNT. Particularly, CF treatment condition for CNT‐coating with 700°C reaction temperature and 30 min reaction time has shown a considerable increase in IFSS approximately of 45% over that of the untreated fiber from which it was processed. The proper justification of fiber–matrix adhesion featured by composite interfacial properties was explained through IFSS. POLYM. COMPOS., 36:1941–1950, 2015. © 2014 Society of Plastics Engineers     

Microstructure and fracture behavior of (co)injection‐molded polyamide 6 composites with short glass/carbon fiber hybrid reinforcement

The mechanical and fracture properties of injection molded short glass fiber)/short carbon fiber reinforced polyamide 6 (PA 6) hybrid composites were studied. The short fiber composites of PA 6 glass fiber, carbon fiber, and the hybrid blend were injection molded using a conventional machine whereas the two types of sandwich skin–core hybrids were coinjection molded. The fiber volume fraction for all formulations was fixed at 0.07. The overall composite density, volume, and weight fraction for each formulation was calculated after composite pyrolysis in a furnace at 600°C under nitrogen atmosphere. The tensile, flexural, and single‐edge notch‐bending tests were performed on all formulations. Microstructural characterizations involved the determination of thermal properties, skin–core thickness, and fiber length distributions. The carbon fiber/PA 6 (CF/PA 6) formulation exhibits the highest values for most tests. The sandwich skin‐core hybrid composites exhibit values lower than the CF/PA 6 and hybrid composite blends for the mechanical and fracture tests. The behaviors of all composite formulations are explained in terms of mechanical and fracture properties and its proportion to the composite strength, fiber orientation, interfacial bonding between fibers and matrix, nucleating ability of carbon fibers, and the effects of the skin and core structures. Failure mechanisms of both the matrix and the composites, assessed by fractographic studies in a scanning electron microscope, are discussed. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 957–967, 2005     

Nanoscale toughening of carbon fiber‐reinforced epoxy composites through different surface treatments

Interests in improving poor interfacial adhesion in carbon fiber‐reinforced polymer (CFRP) composites has always been a hotspot. In this work, four physicochemical surface treatments for enhancing fiber/matrix adhesion are conducted on carbon fibers (CFs) including acid oxidation, sizing coating, silane coupling, and graphene oxide (GO) deposition. The surface characteristics of CFs are investigated by Fourier transform infrared spectroscopy, X‐ray photoelectron spectroscopy, atomic force microscopy, scanning electron microscopy, interfacial shear strength, and interlaminar shear strength. The results showed that GO deposition can remarkably promote fiber/matrix bonding due to improved surface reactivity and irregularity. In comparison, epoxy sizing and acid oxidation afford enhancement of IFSS owing to effective molecular chemical contact and interlocking forces between the fiber and the matrix. Besides, limited covalent bonds between silane coupling and epoxy matrix cannot make up for the negative effects of excessive smoothness of modified CFs, endowing them inferior mechanical properties. Based on these results, three micro‐strengthening mechanisms are proposed to broadly categorize the interphase micro‐configuration of CFRP composite, namely, “Etching” “Coating”, and “Grafting” modifications, demonstrating that proper treatments should be chosen for combining optimum interfacial properties in CFRP composites. POLYM. ENG. SCI., 59:625–632, 2019. © 2018 Society of Plastics Engineers     

Investigation of mechanical properties of alumina nanoparticle‐loaded hybrid glass/carbon‐fiber‐reinforced epoxy composites

This research work investigates the tensile strength and elastic modulus of the alumina nanoparticles, glass fiber, and carbon fiber reinforced epoxy composites. The first type composites were made by adding 1–5 wt % (in the interval of 1%) of alumina to the epoxy matrix, whereas the second and third categories of composites were made by adding 1–5 wt % short glass, carbon fibers to the matrix. A fourth type of composite has also been synthesized by incorporating both alumina particles (2 wt %) and fibers to the epoxy. Results showed that the longitudinal modulus has significantly improved because of the filler additions. Both tensile strength and modulus are further better for hybrid composites consisting both alumina particles and glass fibers or carbon fibers. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39749.     

Influence of two carbon plies on adhesion of unidirectional flax‐fibers reinforced epoxy composites

In this work, we undertook a comparative study of the dynamic dielectric analysis of two unidirectional epoxy composites: flax‐fiber‐reinforced epoxy and flax/carbon‐fiber‐reinforced epoxy (FCFRE). In both composites, three relaxation processes were identified. The first one is the water dipoles polarization imputed to the presence of polar water molecules in flax fiber. The second relaxation process associated with conductivity occurs as a result of the carriers charges diffusion noted for high temperature above glass transition and low frequencies. As for the third dielectric relaxation associated with the interfacial polarization effect is attributable to the accumulation of charges at the fibers/matrix interface. The presence of two carbon plies in the reinforcement gives rise to two interfacial polarization effects in the FCFRE composite. The analysis of the Maxwell–Wagner–Sillars and the water dipoles polarizations using the Havriliak–Negami model revealed that the presence of two plies of carbon can locally decrease the adhesion of flax fibers in the matrix. This analysis was supported by the thermal properties using a differential scanning calorimety and the mechanical properties using a short beam shear test. POLYM. COMPOS., 241–253, 2016. © 2014 Society of Plastics Engineers     

Electrically conductive composites based on epoxy resin containing polyaniline–DBSA‐ and polyaniline–DBSA‐coated glass fibers

Four kinds of polyaniline (PANI)‐coated glass fibers (GF–PANI) combined with bulk PANI particles were synthesized. GF–PANI fillers containing different PANI contents were incorporated into an epoxy–anhydride system. The best conductivity behavior of the epoxy/GF–PANI composites was obtained with a GF–PANI filler containing 80% PANI. Such a composite shows the lowest percolation threshold at about 20% GF–PANI or 16% PANI (glass fiber‐free basis). The PANI‐coated glass fibers act as conductive bridges, interconnecting PANI particles in the epoxy matrix, thus contributing to the improvement of the conductivity of the composite and the lower percolation threshold, compared with that of a epoxy/PANI–powder composite. Particularly, the presence of glass fibers significantly improves the mechanical properties, for example, the modulus and strength of the conductive epoxy composites. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1329–1334, 2004     

Assessment of Glass/Drumstick Fruit Fiber (Moringa oleifera) Reinforced Epoxy Hybrid Composites

Glass fibers/drumstick fruit fibers (GF/DFF) reinforced with epoxy hybrid composites were fabricated using the rule of hybrid mixtures. Properties like impact strength, frictional coefficient, dielectric strength, and chemical resistance were studied. Treated and untreated DFF were reinforced along with GF to assess two different epoxy hybrid composites. The effect of alkali treatment on the above-mentioned properties was also studied. It is observed that the impact strength and frictional coefficient properties of the hybrid composites increased with increase in glass fiber content. Performance was elevated for alkali-treated DFF hybrid composites when compared with untreated DFF. Chemical resistance was significantly increased for all chemicals except carbon tetrachloride due to attack of chloride hydrocarbons on the cross-linking of the epoxy. Elimination of amorphous hemi-cellulose by alkali treatment improved the properties. Fiber-polymer interactions were studied by scanning electron microscopy on the cross-sections of fractured surfaces.     

Fabrication and mechanical properties of glass fiber‐reinforced wood plastic hybrid composites

To fully utilize the resource in the municipal solid waste (MSW) and improve the strength and toughness of wood plastic composites, glass fiber (GF)‐reinforced wood plastic hybrid composites (GWPCs) were prepared through compounding of recycled high‐density polyethylene (HDPE) from MSW, waste wood fibers, and chopped GF. Mechanical tests of GWPCs specimens with varying amounts of GF content were carried out and the impact fractured surface of GWPCs was observed through scanning electron microscope (SEM). The tensile strength of GWPCs and the efficiency coefficient values were predicted by Kelly‐Tyson method. The results indicated that the tensile strength and impact strength of GWPCs could be improved simultaneously by adding type L chopped GF (L‐GF), and would be dropped down when type S chopped GF (S‐GF) was included. The tensile strength of GWPCs was well accordant with the experimental result. The efficiency coefficient values of S‐GF and L‐GF are ?0.19 and 0.63, respectively. Inspection of SEM micrographs indicated that L‐GF had achieved full adhesion with the plastic matrix through addition of maleic anhydride‐g‐polyethylene. The main fracture modes of GWPCs included pullout of GF, broken of matrix, and interfacial debonding. Because of the synergistic effects between hybrid components in GF/wood fiber/HDPE hybrid system, a special 3D network microstructure was formed, which was the main contribution to the significant improvement in the tensile strength and impact strength of L‐GF‐reinforced hybrid composites. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthetic fibers and thermoplastic short‐fiber‐reinforced polymers: Properties and characterization

Among the synthetic fibers, glass fibers (GF) are most widely used in thermoplastic short‐fiber‐reinforced polymers (SFRP), as they offer good strength and stiffness, impact resistance, chemical resistance, and thermal stability at a low price. Carbon fibers (CF) are applied instead of GF, when highest stiffness is required. Other types of synthetic fibers like aramid (AF), basalt (BF), polyacrylonitrile (PAN‐F), polyethylene terephthalate (PET‐F), or polypropylene fibers (PP‐F) are rarely used in SFRP, although they offer some advantages compared with GF. The aim of this article is, to give an overview of various fiber types with regard to their mechanical properties, densities, and prices as well as the performance of their thermoplastic composites. The mechanical properties are presented as Ashby plots of tensile strength versus tensile modulus, both in absolute and specific (absolute value divided by density) values. This overview also focuses on modification of fiber/matrix interaction, as interfacial adhesion has a huge impact on composite performance. A summary of established methods for characterization of fibers, polymers, and composites completes this article. POLYM. COMPOS., 35:227–236, 2014. © 2013 Society of Plastics Engineers     

Micro‐Driving behavior of carbon‐fiber‐reinforced epoxy resin for standing‐wave ultrasonic motor

The application of the friction drive of carbon‐fiber‐reinforced composites to a standing‐wave ultrasonic motor was investigated. Friction drive tests were conducted on carbon‐fiber‐reinforced epoxy resins (CF/epoxy) by home‐made test rig, which was based on plate‐rod vibrator. The effects of fiber orientation and ply thickness on dynamic drive and dynamic normal forces were investigated. Fiber orientation angle and ply thickness affected friction drive. Different dynamic drive forces, which varied both in amplitude and period, were observed for CF/epoxy composites with different winding angles. A CF/epoxy composite with a winding angle of 30° showed the largest dynamic drive force (∼0.45 N) and the shortest contact period (∼26 μs). The period of dynamic normal force was uniform (∼65 μs) for various CF/epoxy composites. Wear traces of different composites exhibited different wear modes, such as scuffing, peeling, and shearing. The anisotropic property of CF/epoxy material affected the drive process of standing‐wave ultrasonic motor. The current study taking the carbon‐fiber‐reinforced epoxy resin as an example of anisotropic materials arise more enough attention on inexpensive, biodegradable, and renewable alternatives for the efficient and durative drive of a standing‐wave ultrasonic motor. POLYM. COMPOS., 37:2152–2159, 2016. © 2015 Society of Plastics Engineers     

Structure–properties relations in titanium‐based thermoplastic fiber–metal laminates

This paper investigates the interfacial, tensile, and fatigue properties of a titanium alloy fiber–metal laminate (Ti‐FML) based on woven glass‐fiber‐reinforced polyetherimide (GF/PEI). Initial tests, using the single cantilever beam (SCB) geometry have shown that it is not necessary to surface treat the titanium alloy in order to achieve a high value of metal–composite interfacial fracture toughness. Tensile tests have shown that the mechanical properties of the FML lie between those offered by its constituent materials. Tension–tension fatigue tests have shown that the fatigue lives of these laminates are superior to those offered by the plain titanium alloy. The mechanical properties of this glass fiber/PEI FML have also been compared with those offered by an FML based on a unidirectional carbon‐fiber‐reinforced polyetheretherketone (CF/PEEK) composite. Here, it has been shown that although the fatigue properties of this woven GF/PEI composite are inferior to those of the CF/PEEK FML, they do offer a higher temperature capability due to the higher glass transition temperature of the PEI matrix. Polym. Compos. 27:264–270, 2006. © 2006 Society of Plastics Engineers.     

Temperature effect on interfacial bonding property of single‐carbon fiber/epoxy resin composite

The changes in interfacial fracture energy of three kinds of commercially sized carbon fiber (CF)/epoxy resin composites in the range from ambient temperature to 130°C were investigated using the single‐fiber fragmentation test to evaluate the heat resistance of the interphase. The effects of CF sizing on the interfacial bonding property were studied using desized CF/epoxy resin composites. Thermogravimetric analysis and differential scanning calorimetry of the combination of sizing and matrix were employed to investigate the role of sizing on the variations in the fiber/matrix interfacial property under elevated temperature. The interfacial fracture energy values of all the studied CF composites were found to decrease quickly during the initial stage of temperature rise and drop gradually at higher temperature. At elevated temperature, the desized CF composites had higher heat resistance than the corresponding sized fiber composites. The differences in the interfacial heat resistance among the three kinds of CF composites and the difference in the interfacial thermal stability between the sized and the desized fiber composites were related to different glass transition temperatures of the interphases. The interaction between sizing and the matrix and the chain motion of the crosslink structure of the interphase has been suggested to determine the interfacial heat resistance. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers