Preparation of bi‐continuous poly(acrylonitrile‐co‐methyl acrylate) microporous membranes by a thermally induced phase separation method

Poly(acrylonitrile‐co‐methyl acrylate) [P(AN‐MA)] flat microfiltration membranes were successfully prepared via the thermally induced phase separation (TIPS) method, by using low polar caprolactam (CPL) and methoxypolyethylene glycol 550 (MPEG 550) as the mixed diluent. In this work, P(AN‐MA) membranes exhibit bi‐continuous networks, porous surfaces, high porosity, and big pore size, when membrane fabricated from a high MPEG 550 content, low P(AN‐MA) concentration, and small cooling rate, it can be dry state preservation and do not need to be impregnated by any solvent. When the ternary system was composed of 15 wt % P(AN‐MA), 12.5 wt % CPL, and 87.5 wt % MPEG 550, formed at 25 °C air bath, membrane has the highest water flux of 4420 L m^?2 h^?1. The obtained P(AN‐AN) membrane displays a high carbonic black ink rejection ranging from 83.7 to 98.5 wt %. Moreover, P(AN‐MA) polymer not only retains the advantages of PAN but also reduces the polar component from 16.2 to 10.77 MPa^0.5. It can be used membrane matrix to obtain pore structure and excellent mechanical property membrane via TIPS. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46173.     

Novel nanocomposite of poly(acrylonitrile‐co‐glycidyl methacrylate) crosslinked with Jeffamine‐functionalized multiwalled carbon nanotubes as gel polymer electrolytes

Multiwalled carbon nanotubes (MWCNTs) were functionalized with α,ω‐diamino poly(propylene oxide) (Jeffamine) of different molecular weights and crosslinked with poly(acrylonitrile‐co‐glycidyl methacrylate) [P(AN‐GMA)] to prepare a novel nanocomposite for applications in gel polymer electrolytes (GPEs). The synthesized copolymer was characterized by ¹H‐NMR, Fourier transform infrared, and thermal analysis. Scanning electron microscope observation revealed that the Jeffamine‐functionalized MWCNTs distributed uniformly in the nanocomposite membrane. The mechanical behaviors of the nanocomposite membranes were investigated. It was found that the crosslinked nanocomposite membranes of P(AN‐GMA) and Jeffamine‐functionalized MWCNTs exhibited much higher mechanical strength than the counterpart nanocomposite obtained by physical blending. Moreover, the weight content and molecular weights of Jeffamine had an effect on the mechanical properties of the nanocomposites. Differential scanning calorimeter measurements showed that the crosslinked nanocomposite membranes were amorphous. GPEs based on the nanocomposite were prepared and characterized by complex impedance measurements. The GPE based on the nanocomposite of P(AN‐GMA) crosslinked with 6 wt % of MWCNTs functionalized by Jeffamine D400 showed an ionic conductivity of about 3.39 × 10^?4 S cm^?1 at 25°C, which is much higher than the counterpart nanocomposite of physically blended P(AN‐GMA) and MWCNTs. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Structure and properties of poly(acrylonitrile‐co‐methyl acrylate) membranes prepared via thermally induced phase separation

Poly(acrylonitrile‐co‐methyl acrylate) [(P(AN‐MA)] microporous membranes were prepared via a thermally induced phase separation (TIPS) process by using γ‐butyrolactone (γ‐BA) and glyceryl triacetate (GTA) as the mixed diluent. The purpose of this work is to investigate the effects of the γ‐BA content, P(AN‐MA) concentration, and cooling rate on the structure and properties of P(AN‐MA) membranes. A lacy structure with high connectivity was formed with 50 wt % γ‐BA, and 50 wt % GTA comprising the mixed diluent. With an increase in the γ‐BA content, the pore structure acquires semi‐closed or completely closed cell‐like morphologies. The different phase separation mechanisms greatly influence the mechanical properties of the P(AN‐MA) membranes. P(AN‐MA) membranes with a lacy structure possess better tensile strength than those with semi‐closed or completely closed cell‐like structures. The membrane pore size grows larger when the TIPS process utilizes a higher γ‐BA content and a lower cooling rate. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43444.     

Properties and degradation behavior of surface functionalized MWCNT/poly(L‐lactide‐co‐ε‐caprolactone) biodegradable nanocomposites

In this research, poly(L ‐lactide‐co‐ε‐caprolactone) (PLACL) reinforced with well‐dispersed multiwalled carbon nanotubes (MWCNTs) nanocomposites were prepared by oxidization and functionalization of the MWCNT surfaces using oligomeric L ‐lactide (LA) and ε‐caprolactone (CL). It is found that the surface functionalization can effectively improve the dispersion and adhesion of MWCNTs in PLACL. The surface functionalization will have a significant effect on the physical, thermomechanical, and degradation properties of MWCNT/PLACL composites. The tensile modulus, yield stress, tensile strength, and elongation at break of composite increased 49%, 60%, 70%, and 94%, respectively, when the concentration of functionalized MWCNTs in composite is 2 wt %. The in vitro degradation rate of nanocomposites in phosphate buffer solution increased about 100%. The glass transition temperature (T_g) of composites was decreased when the concentration of functionalized MWCNTs is 0.5 wt %. With further increasing the concentration of functionalized MWCNTs, the T_g was increased. The degradation kinetics of nanocomposites can be engineered and functionalized by varying the contents of pristine or functionalized MWCNTs. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Poly(ether imide) membranes modified with charged surface‐modifying macromolecule—Its performance characteristics as ultrafiltration membranes

Modification of poly (ether imide) (PEI) ultrafiltration (UF) membranes was attempted by blending charged surface modifying macromolecule (cSMM). Compared to the pure PEI membrane, blending of PEI with cSMM resulted in blend membranes with enhanced UF characteristics such as lower hydraulic resistance (R_m) and higher pure water flux (PWF) coupled with higher water content (WC). Among the various modified membranes, blend membranes with 5 wt % cSMM concentration exhibited higher PWF (60.38 L m^?2 h^?1), WC (73.6%), protein permeate flux (27.12 L m^?2 h^?1) and lower flux decline rate (R_fd) (55.1%), R_m (5.21 kPa/L m^?2 h^?1), bovine serum albumin (BSA) rejection (87.1%). Meanwhile, the fouling resistant ability was studied by flux recovery ratio (FRR) after water and alkali cleaning, irreversible and reversible fouling rate. Higher FRR after water cleaning (95.07%), FRR after alkali cleaning (97.1%), reversible fouling rate (50.14%) and lower irreversible fouling rate (5%) exhibited by 5 wt % cSMM membranes showed its better antifouling ability compared to pure PEI and other blend membranes because of its higher hydrophilic nature. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40320.     

Blends of polyamide1010 with unmodified and maleic‐anhydride‐grafted high‐impact polystyrene

The crystallization behaviors, dynamic mechanical properties, tensile, and morphology features of polyamide1010 (PA1010) blends with the high‐impact polystyrene (HIPS) were examined at a wide composition range. Both unmodified and maleic‐anhydride‐(MA)‐grafted HIPS (HIPS‐g‐MA) were used. It was found that the domain size of HIPS‐g‐MA was much smaller than that of HIPS at the same compositions in the blends. The mechanical performances of PA1010–HIPS‐g‐MA blends were enhanced much more than that of PA1010–HIPS blends. The crystallization temperature of PA1010 shifted towards higher temperature as HIPS‐g‐MA increased from 20 to 50% in the blends. For the blends with a dispersed PA phase (≤35 wt %), the T_c of PA1010 shifted towards lower temperature, from 178 to 83°C. An additional transition was detected at a temperature located between the T_g's of PA1010 and PS. It was associated with the interphase relaxation peak. Its intensity increased with increasing content of PA1010, and the maximum occurred at the composition of PA1010–HIPS‐g‐MA 80/20. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 857–865, 1999     

Multiwalled carbon nanotubes‐based polypropylene composites: Influence of interfacial interaction on the crystallization behavior of polypropylene

Composites of polypropylene (PP) and multi‐walled carbon nanotubes (MWCNTs) were prepared via melt‐mixing utilizing Li‐salt of 6‐amino heaxanoic acid (Li‐AHA) modified MWCNTs in the presence of a compatibilizer (polypropylene‐g‐maleic anhydride; PP‐g‐MA). Improved interaction between the anhydride group of PP‐g‐MA and the amine functionality of Li‐AHA was confirmed via FTIR and Raman spectroscopic analysis. A higher glass transition temperature (T_g) of the PP phase has been observed in these composites as compared to pristine MWCNTs‐based composites. The crystallization temperature (T_c) of the PP phase was increased as a function of pristine MWCNTs concentration in PP/MWCNTs composites indicating hetero‐nucleating action of MWCNTs. However, T_c value was decreased in the presence of Li‐AHA modified MWCNTs indicating the adsorbed Li‐AHA on the MWCNTs surface. Moreover, T_c value was higher in the presence of Li‐AHA modified MWCNTs with PP‐g‐MA as compared to that of without PP‐g‐MA, suggesting the desorbed Li‐AHA from the MWCNTs surface due to melt‐interfacial reaction. Further, MWCNTs were extracted by hot vacuum filtration technique from PP/MWCNTs composites containing Li‐AHA and PP‐g‐MA. The isothermal crystallization kinetics showed a variation in crystallization behavior of the PP phase in the corresponding composites as compared to the “extracted MWCNTs.” POLYM. ENG. SCI., 57:183–196, 2017. © 2016 Society of Plastics Engineers     

Pilot‐plant production of xylo‐oligosaccharides from corncob by steaming,enzymatic hydrolysis and nanofiltration

This paper reports a pilot‐plant production process for xylo‐oligosaccharides (mainly xylobiose and xylotriose) from corncob meal by steaming treatment followed by enzymatic hydrolysis and nanofiltration. The effects of corncob meal pretreatment, steaming temperature and time were investigated in order to obtain maximum extraction of xylan and to minimize the autohydrolysis of xylan into xylose. The enzymatic reaction was carried out using Aspergillus niger AN‐1.15 endo‐xylanase at 55 °C and the optimum enzymatic hydrolysis time was 5 h. The conventional downstream processing for purification of xylo‐oligosaccharides was incorporated with nanofiltration technology, giving benefits of energy saving and removal of monosaccharides. The final product from 40 kg of corncob meal was 10 dm³ of xylo‐oligosaccharide syrup (800 g dm^?3 total sugar), containing 74.5% xylobiose and xylotriose. Copyright © 2004 Society of Chemical Industry     

Influence of LiClO4 on the thermal,mechanical, and morphological properties of P(DMS‐co‐EO)/ P(EPI‐co‐EO) blends

The UV‐vis absorption, thermal analysis, ionic conductivity, mechanical properties, and morphology of a blend of poly(dimethylsiloxane‐co‐ethylene oxide) [P(DMS‐co‐EO)] and poly(epichlorohydrin‐co‐ethylene oxide) [P(EPI‐co‐EO)] (P(DMS‐co‐EO)/P(EPI‐co‐EO) ratio of 15/85 wt %) with different concentrations of LiClO₄ were studied. The maximum ionic conductivity (σ = 1.2 × 10^?4 S cm^?1) for the blend was obtained in the presence of 6% wt LiClO₄. The crystalline phase of the blend disappeared with increasing salt concentration, whereas the glass transition temperature (T_g) progressively increased. UV‐vis absorption spectra for the blends with LiClO₄ showed a transparent polymer electrolyte in the visible region. The addition of lithium salt decreased the tensile strength and elongation at break and increased Young's modulus of the blends. Scanning electron microscopy showed separation of the phases between P(DMS‐co‐EO) and P(EPI‐co‐EO), and the presence of LiClO₄ made the blends more susceptible to cracking. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1230–1235, 2004     

Synthesis of a heat‐resistant DOPO derivative and its application as flame‐retardant in engineering plastics

A star‐shaped DOPO derivative (GL‐3DOPO, P content 10.8 wt %) was synthesized through a two‐step reaction involving glycerol, acryloyl chloride, and DOPO. The derivative demonstrated a great improvement of thermal decomposition temperature increased to 360 °C from 194 °C (under N₂ atmosphere), promoting its application in thermoplastics of high processing temperature. When blended with engineering plastics including PET, PBT, PC, PA6, and PA66 at a GL‐3DOPO loading of 25 wt %, all the compounds reached the UL94 V‐0 level and increased limit oxygen index (LOI). In PET system, LOI raised from 22.8% to 35.4% with P 2.5 wt % and passed the V‐0 test with only 0.8 P wt %. Compact char layers were found in the PET system after LOI test, suggesting that GL‐3DOPO acted both in gas and condensed‐phase mode. All results indicated that GL‐3DOPO could be a potential flame‐retardant for engineering plastics. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44892.     

Reactive compatibilization of poly(methyl acrylate‐ran‐acrylonitrile)/poly(ethylene) blends through amine–anhydride coupling

Methyl acrylate/acrylonitrile copolymers (MA/AN) were reactively compatibilized as the dispersed phase into poly(ethylene) (PE) for potential hydrocarbon barrier materials. The MA/AN was made reactive by including p‐aminostyrene (PAS), yielding terpolymers (MA/AN/PAS) with pendant primary amine functionality (number average molecular weight = 65–133 kg mol^?1, dispersity (?)=1.83–2.53, molar composition of PAS in copolymer F_PAS = 0.03–0.14, molar composition of AN = F_AN = 0.27–0.52). The non‐functional MA/AN and amino functional MA/AN/PAS were each melt blended into PE that was grafted with maleic anhydride (PE‐g‐MAnn) at 200 °C at 70:30 wt % PE‐g‐MAnn:co/terpolymer. After extrusion, the dispersed phase particle size (volume to surface area diameter, ) was coarse (12.6 μm) for the non‐reactive blend whereas it was much lower for the reactive blend ( = 1.2 μm). Coarsening after annealing at 150 °C was slow, but the domain sizes increased only slightly for both cases. The reactive blend was deemed sufficiently stable and thus was suitable as a candidate barrier material for further testing against olefins. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44177.     

Optical resolution of (R,S)‐2‐phenyl‐1‐propanol through enantioselective ethycellulose membranes

Enantioselective membrane was prepared using ethyl cellulose (EC) as membrane material. The flux and permselective properties of membrane using aqueous solution of (R,S)‐2‐phenyl‐1‐propanol as feed solution was studied. The employed membrane process was a pressure driven process. All kinds of important conditions including preparation and operation of membranes were investigated in this experimentation. When the membrane was prepared with 18 wt % EC, 20 wt % N,N‐dimethylformamide in casting solution, 13 min evaporation time and 0°C temperature of water bath for the gelation of the membrane, and the operating pressure and feed solution of (R,S)‐2‐phenyl‐1‐propanol were 0.2 MPa and 1.5 mg/mL, respectively, over 90% of enantiomeric excess (e.e.) and 44.2 (mg/m² h) of flux were obtained. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Free‐standing hybrid anion‐exchange membranes for application in fuel cells

A series of free‐standing hybrid anion‐exchange membranes were prepared by blending brominated poly(2,6‐dimethyl‐1,4‐phenylene oxide) (BPPO) with poly(vinylbenzyl chloride‐co‐γ‐methacryloxypropyl trimethoxy silane) (poly(VBC‐co‐γ‐MPS)). Apart from a good compatibility between organic and inorganic phases, the hybrid membranes had a water uptake of 32.4–51.8%, tensile strength around 30 MPa, and T_d temperature at 5% weight loss around 243–261°C. As compared with the membrane prepared from poly (VBC‐co‐γ‐MPS), the hybrid membranes exhibited much better flexibility, and larger ion‐exchange capacity (2.19–2.27 mmol g^?1) and hydroxyl (OH^?) conductivity (0.0067–0.012 S cm^?1). In particular, the hybrid membranes with 60–75 wt % BPPO had the optimum water uptake, miscibility between components, and OH^? conductivity, and were promising for application in fuel cells. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Catalytic potential of a poly(AAc‐co‐HPMA‐cl MBAm)‐matrix‐immobilized lipase from a thermotolerant Pseudomonas aeruginosa MTCC‐4713

A purified alkaline thermo‐tolerant lipase from Pseudomonas aeruginosa MTCC‐4713 was immobilized on a series of five noble weakly hydrophilic poly(AAc‐co‐HPMA‐cl MBAm) hydrogels. The hydrogel synthesized by copolymerizing acrylic acid and 2‐hydroxy propyl methacrylate in a ratio of 5 : 1 (HG_5:1 matrix) showed maximum binding efficiency for lipase (95.3%, specific activity 1.96 IU mg^?1 of protein). The HG_5:1 immobilized lipase was evaluated for its hydrolytic potential towards p‐NPP by studying the effect of various physical parameters and salt‐ions. The immobilized lipase was highly stable and retained ～92% of its original hydrolytic activity after fifth cycle of reuse for hydrolysis of p‐nitrophenyl palmitate at pH 7.5 and temperature 55°C. However, when the effect of pH and temperature was studied on free and bound lipase, the HG_5:1 immobilized lipase exhibited a shift in optima for pH and temperature from pH 7.5 and 55°C to 8.5 and 65°C in free and immobilized lipase, respectively. At 1 mM concentration, Fe³⁺, Hg²⁺, NH₄⁺, and Al³⁺ ions promoted and Co²⁺ ions inhibited the hydrolytic activities of free as well as immobilized lipase. However, exposure of either free or immobilized lipase to any of these ions at 5 mM concentration strongly increased the hydrolysis of p‐NPP (by ～3–4 times) in comparison to the biocatalysts not exposed to any of the salt ions. The study concluded that HG_5:1 matrix efficiently immobilized lipase of P. aeruginosa MTCC‐4713, improved the stability of the immobilized biocatalyst towards a higher pH and temperature than the free enzyme and interacted with Fe³⁺, Hg²⁺, NH₄⁺, and Al³⁺ ions to promote rapid hydrolysis of the substrate (p‐NPP). © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4252–4259, 2006     

Efficient Anchorage of Palladium Nanoparticles on the Multi‐Walled Carbon Nanotubes as Electrocatalyst for the Hydrazine Electrooxidation in Strong Acidic Solutions

A facile homogeneous precipitation–reduction reaction method, which involves PdCl₂ → PdO · H₂O → Pd⁰ reaction path, is used to synthesize the multi‐walled carbon nanotubes (MWCNTs) supported Pd nanoparticles (Pd/MWCNTs) catalysts. The particle size of Pd/MWCNTs catalysts can be easily tuned by controlling the hydrolysis temperature of PdCl₂. X‐ray diffraction (XRD) and transmission electron microscopy (TEM) measurements show the particle size of Pd/MWCNTs catalysts increases with hydrolysis temperature of PdCl₂, which is ascribed to the fact that the particle size of PdO · H₂O nanoparticles increases with hydrolysis temperature of PdCl₂. At the lower hydrolysis temperature, the as‐prepared Pd/MWCNTs catalyst possesses the higher dispersion and the smaller particle size. Consequently, the resultant Pd/MWCNTs catalyst exhibits the big electrochemical active surface area and the excellent electrocatalytic performance for hydrazine electrooxidation in strong acidic solutions. In addition, the electrochemical measurement indicate that particle size effect of Pd‐NPs occurs during the N₂H₄ electrooxidation. In brief, the mass activity and specific activity of the Pd/MWCNTs catalyst increases and decreases with decreasing the particle size of Pd‐NPs for the N₂H₄ electrooxidation, respectively.     

Divinyl benzene cross‐linked HTPB‐based polyurethaneurea membranes for separation of p‐/o‐xylene mixtures by pervaporation

Cross‐linked hydroxy terminated polybutadiene (HTPB)‐based polyurethaneurea (PU), HTPB‐divinyl benzene (DVB)‐PU, was synthesized by a three‐step polymerization process. It was first used as membrane material to separate p‐/o‐xylene mixtures by pervaporation (PV). The effects of the content of cross‐linker DVB, feed concentration, and operating temperature on the PV performance of HTPB‐DVB‐PU membranes were investigated. The membranes demonstrated p‐xylene permselectivity as well as high total flux. The introduction of DVB significantly enhanced the temperature resistance ability of the HTPB‐DVB‐PU membranes. With increasing DVB content, the separation factor increased while the total flux decreased a little. The highest separation factor reaches 2.01 and the total flux is 33 g/m²h with feed concentration of 10 wt % p‐xylene at 30°C. These PV performances with increasing DVB content were explained in terms of the view point of chemical compositions and physical structures of the HTPB‐DVB‐PU membranes. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Preparation of poly(methyl methacrylate‐co‐maleic anhydride)/SiO2?TiO2 hybrid materials and their thermo‐ and photodegradation behaviors

The optically transparent poly(methyl methacrylate‐co‐maleic anhydride) P(MMA‐co‐MA)/SiO₂? TiO₂ hybrid materials were prepared using 3‐aminopropyl triethoxysilane as a coupling agent for organic and inorganic components. Real‐time FTIR was used to monitor the curing process of hybrid sol, indicating that imide group formation decreased with increasing titania content. scanning electron microscopy, atomic force microscopy, and differential scanning calorimetry results confirmed their homogeneous inorganic/organic network structures. TGA analysis showed that incorporated titania greatly prohibits the thermodegradation of hybrid films, especially at the content of 5.3 wt %, showing an increase of about 32.6°C at 5% loss temperature in air. The UV degradation behavior of P(MMA‐co‐MA) studied by quasi‐real‐time FTIR showed that TiO₂ incorporated in the hybrid network provides a photocatalytic effect rather than a UV‐shielding effect. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 1714–1724, 2005     

Poly(ether sulfone) supported hybrid poly(vinyl alcohol)–maleic acid–silicone dioxide membranes for the pervaporation separation of ethanol–water mixtures

Microporous poly(ether sulfone) (PES) supported hybrid polymer–inorganic membranes were prepared by the crosslinking of poly(vinyl alcohol) (PVA), maleic acid (MA), and SiO₂ via an aqueous sol–gel route and a solution‐casting method. The membrane performance was tested for the pervaporation separation of ethanol–water mixtures from 20 to 60 °C with a feed ethanol concentration of 96 wt %. The membrane characterization results reveal that different SiO₂ loadings affected the crystallinity and roughness of the membranes. The PVA–MA–SiO₂ membrane containing 10 wt % SiO₂ showed that SiO₂ nanoparticles were well dispersed within the polymer matrix; this resulted in significant enhancements in both the flux and selectivity. The membrane achieved a high water permeability of 1202 g·μm·m^?2 h^?1 kPa^?1 and a selectivity of 1027 for the separation of a 96 wt % ethanol‐containing aqueous solution. This enhanced membrane performance might have been due to the dense crosslinking membrane network, increased free volume, and uniform distribution of SiO₂ nanoparticles. Both the water and ethanol fluxes increased with the feed water concentration and temperature. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 44839.     

Isothermal crystallization kinetics of polypropylene in melt‐mixed composites of polypropylene and multi‐walled carbon nanotubes

The isothermal crystallization behaviour of the polypropylene (PP) phase in PP/multi‐walled carbon nanotubes (MWCNTs) composites has been investigated via differential scanning calorimetric analysis, which showed the influence of the varying dispersion level of MWCNTs in the respective PP matrix. PP/MWCNTs composites were prepared via melt‐blending technique, wherein two different grades of MWCNTs of varying average “agglomerate” size and varying entanglements (N‐MWCNTs and D‐MWCNTs) were utilized. Furthermore, the influence of melt‐viscosity of the PP phase was investigated on the crystallization kinetics of the PP/MWCNTs composites. Heterogeneous nucleation ability of MWCNTs has resulted in a decrease in half time of crystallization (t _1/2) from ～14 min for pure PP to ～6 min for PP/N‐MWCNTs and ～11 min for PP/D‐MWCNTs composites at 1 wt% of MWCNTs at 132 °C. Overall rate of crystallization (k) has significantly increased to 4.9 × 10^?2 min^?1 for PP/N‐MWCNTs composite as compared with 6.2 × 10^?3 min^?1 for PP/D‐MWCNTs composite at 0.5 wt% of MWCNTs at 132 °C. Moreover, the effect of a novel organic modifier, Li‐salt of 6‐amino hexanoic acid along with a compatibilizer (PP‐g‐MA) has also been investigated on the crystallization kinetics of the PP phase in PP/MWCNTs composites. POLYM. ENG. SCI., 57:1136–1146, 2017. © 2017 Society of Plastics Engineers     

Study on the acidic hydrolysis process of poly(N‐vinylformamide/acrylonitrile) fiber

A convenient method of preparing chelating fiber with amine groups on the fiber surface was developed. The precursor polymer of Poly(N‐vinylformamide/acrylonitrile) (P(NVF/AN)) was synthesized via solution polymerization, using N‐vinylforaimde as a functional monomer. The solution of P(NVF/AN) was spun through a wet spinning method and the precursor fiber was hydrolyzed in the hydrochloric acid solution to convert formamide moieties to the corresponding amine. The influence of hydrolytic conditions on hydrolysis degree, such as hydrolysis temperature, hydrolysis time, and hydrochloric acid concentrations were examined experimentally. The hydrolysis degree of the precursor fiber was evaluated by potentiometric and conductometric titrations. The changes of the structure and properties of the fibers were characterized through infrared spectroscopy, scanning electron microscopy, and tensile strength tester. The results showed that the hydrolysis degree was limited in acidic hydrolysis because of the electrostatic repulsion among the cationic amine groups and proton. The hydrolysis degree of precursor fiber reached nearly 60%, and the chelating fiber remained the adequate mechanical properties under the suitable hydrolysis condition. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008