Synthesis of phenolphthalein/bisphenol A-based poly(arylene ether nitrile) copolymers: Preparation and properties of films

Poly(arylene ether nitrile) (PEN) is a class of high-performance engineering plastics of poly(arylene ether) with cyano groups as side groups, which can get improved thermal, mechanical, and electrical properties through simple molecular structure design. In this work, a series of PEN (BPA/PP based PEN) copolymers were synthesized with varying amounts of phenolphthalein and bisphenol A. The influence of the copolymer molecular structure variations on the thermal, mechanical, and dielectric properties of PEN copolymer films was investigated. The results demonstrated that the BPA/PP based PEN copolymer films have great mechanical properties and low dielectric constant, as well as enhanced thermal properties. The highest 5% weight loss temperature of 494.9°C was obtained by PEN-B7P3, while the highest glass transition temperature of 238.6°C was obtained by PEN-B3P7. Porous BPA/PP based PEN films prepared by non-solvent induced phase separation (NIPS) exhibited satisfactory mechanical properties and the highest tensile strength of 9.4 MPa was achieved. Moreover, the introduction of the phenolphthalein structure into the PEN molecular chain can improve the heat resistance of the PEN copolymers without deteriorating the dielectric properties, which gives the copolymers great potential as candidates for applications in flexible electronics and wireless communication.     

Compatibility,rheological, and thermal properties of the melt blends of PEN (HQ/PP) with PEN (HQ/RS)

Two kinds of polyarylene ether nitriles (PEN) copolymers PEN (HQ/PP) and PEN (HQ/RS) were synthesized using 2,6-dicholorobenzonitrile (DCBN) with equal molar of phenolphthalein (PP) and hydroquinone (HQ), DCBN with equal molar of HQ and resorcin (RS), respectively. The melt-mixed blends of two PENs over the complete composition range were characterized by dynamic mechanical analyses (DMA), tensile testing, scanning electronic microscopy (SEM), and capillary rheometer test for their compatibility, thermal, mechanical, and melt flow properties study. DMA show a considerable compatibility between the two PENs. Morphology examinations reveal good component dispersion and strong interface adhesion. The capillary rheometer test found that the blending of PEN (HQ/RS) enhanced the fluidity of the PEN (HQ/PP)/PEN (HQ/RS) blends by reducing its viscosity, which is beneficial to the processability of PEN (HQ/PP). © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

聚芳醚腈合金的制备及性能研究

将2类聚芳醚腈（PEN）共聚物PEN（HQ／RS）和PEN（HQ／PP）,按不同质量比通过熔融共混制备PEN合金材料,测试其相容性、力学性能和热性能,发现聚合物合金在PEN（HQ／RS）质量分数分别为20％和80％时相容性良好,PEN（HQ／RS）的加入改善了PEN（HQ／PP）的加工性能,实验中不同质量比的合金均具有优良的力学性能和热性能。     

Mechanical,hygroscopic, and thermal properties of ultrathin polymeric substrates for magnetic tapes

Mechanical, hygroscopic, and thermal properties of improved ultrathin polymeric films for magnetic tapes are presented. These films include poly(ethylene terephthalate) (PET), poly(ethylene naphthalate) (PEN), and aromatic polyamide (ARAMID). PET films are currently the most commonly used polymeric substrate material for magnetic tapes, followed by PEN and ARAMID. The thickness of the films ranges from 6.2 to 4.8 μm. Tensile tests were run to obtain the Young's modulus, F5 value, strain at yield, breaking strength, and strain at break. The storage modulus, E′, and the loss tangent, tan δ, were measured using a dynamic mechanical analyzer (DMA) at temperature ranges of ?50 to 150°C (for PET) and ?50 to 210°C (for PEN and ARAMID) and at a frequency range of 0.016–28 Hz. Frequency–temperature superposition was used to predict the dynamic mechanical behavior of the films over a 28‐decade frequency range. Short‐term longitudinal creep behavior of the films during 10, 30, 60, and 300 s, 7 MPa, were measured at 25 and 55°C. Long‐term longitudinal creep measurements were performed at 25, 40, and 55°C for 100 h. The Poisson's ratio and 50‐h long‐term lateral creep were measured at 25°C/15% RH, 25°C/50% RH, 25°C/80% RH, and 40°C/50% RH. The in‐plane coefficient of hygroscopic expansion (CHE) at 25°C/20–80% RH and the coefficient of thermal expansion (CTE) at 30–70°C were measured for all the samples. The properties for all films are summarized. The relationship between the polymeric structure and the mechanical and physical properties are discussed, based on the molecular structure, crystallinity, and molecular orientation. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3052–3080, 2003     

Crystallized polyarylene ether nitrile blends with improved thermal,mechanical, dielectric properties,and processability

In this work, the biphenol polyarylether nitrile (BP‐PEN) films with improved processability were prepared by blending low molecular weight (LMW) with high molecular weight (HMW) of BP‐PEN. The hybrid membrane exhibited excellent thermal stability and mechanical strength. The T_id values of the films were as high as 505°C–522°C. Melting behavior studies indicated that the crystallinity of LMW BP‐PEN was higher than that of HMW, which was confirmed by the X‐ray diffraction (XRD) patterns analysis as well. Scanning electron microscope (SEM) provided additional information on morphology and phase adhesion. Additionally, the polymer crystallinity dependent on dielectric properties of blends films is reported. Most importantly, it is found that the combination of LMW and HMW BP‐PEN would be an effective method to simultaneously increase the mechanical, thermal, dielectric properties, and polymer processability. POLYM. COMPOS., 38:126–131, 2017. © 2015 Society of Plastics Engineers     

Rigid thermosetting liquid molding resins from renewable resources. II. Copolymers of soybean oil monoglyceride maleates with neopentyl glycol and bisphenol A maleates

Soybean oil monoglycerides (SOMG), obtained by the glycerolysis of soybean oil, were reacted with maleic anhydride to produce SOMG maleate half esters. The copolymers of the SOMG maleates with styrene produced rigid thermosetting polymers. The dynamic mechanical analysis (DMA) of this polymer showed a glass‐transition temperature (T_g) around 133°C and a storage modulus (E′) value around 0.94 GPa at 35°C. The tensile tests performed on this polymer showed a tensile strength of 29.36 MPa and a tensile modulus of 0.84 GPa. Mixtures of SOMG with neopentyl glycol (NPG) and SOMG with bisphenol A (BPA) were also maleinized under the same reaction conditions and the resulting maleates were then copolymerized with styrene. The resulting polymers were analyzed for their mechanical properties. The T_g of the copolymers of the SOMG/NPG maleates with styrene was 145°C and the E′ value at 35°C was 2 GPa. The tensile strength of this polymer as calculated from the stress–strain data was 15.65 MPa and the tensile modulus was 1.49 GPa. The T_g of the copolymers of SOMG/BPA maleates, on the other hand, was found to be around 131°C and the E′ value was 1.34 GPa at 35°C. The changes observed in the mechanical properties of the resulting polymers with the introduction of NPG maleates and BPA maleates to the SOMG maleates can be explained by the structural changes on the polymer backbone. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 972–980, 2002     

Effect of different aromatic amines on the crosslinking behavior and thermal properties of phthalonitrile oligomer containing biphenyl ethernitrile

To find a proper amine to promote the processability of phthalonitrile‐based composites, three different aromatic amines: 4‐aminophenoxyphthalonitrile (APN), 2,6‐bis (4‐diaminobenzoxy) benzonitrile (BDB) and 4,4′‐diaminediphenyl sulfone (DDS) were used as curing agents to investigate the crosslinking behavior and thermal decomposition behavior of phthalonitrile oligomer containing biphenyl ethernitrile (2PEN‐BPh). Differential scanning calorimeter (DSC) and dynamic rheological analysis were employed to study the curing reaction behavior of the phthalonitrile/amine blends and prepolymers. The studies revealed that BDB was the preferred curing agent and the preferred concentration of BDB was 3 wt %. The thermal properties of the 2PEN‐BPh polymers were monitored by TGA, and the results indicated that all the completely cured 2PEN‐BPh polymers maintained good structure integrity upon heating to elevated temperatures and these polymers could thermal stabilize up to over 550°C in both air and nitrogen atmospheres. Dynamic mechanical analysis (DMA) showed the glass transition temperature (T_g) exceeded 450°C when the 2PEN‐BPh polymer post cured at 375°C for 8 h. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Texture and morphology of biaxially stretched poly(ethylene naphthalene‐2,6‐dicarboxylate)

The orientation of poly(ethylene naphthalene‐2,6‐dicarboxylate) (PEN) films with different morphologies were studied by wide‐angle X‐ray diffraction. Different structures were obtained by thermally treating biaxially stretched PEN samples. Virgin and thermally treated (1 h at 240, 250, and 260°C) samples of PEN bioriented films were characterized by DSC to determine the glass‐transition temperature and the crystallinity ratio. To define the orientation of crystallites in the 25 μm thick bioriented samples, pole figures were recorded for various PEN samples, as a function of their position in the transverse drawing direction. The significant result is that there is a dominant crystal population, whose c‐axis direction varies from +45° at one sample edge to ?45° at the other edge, the orientation at the center being parallel to the transverse direction. There is also a secondary population, which can be seen only near the center. DSC studies also showed that by increasing the annealing temperature the crystallinity ratio was increased and pole figures showed that the texture was modified, probably because of disorientation mainly from an annealing temperature of 260°C. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2224–2232, 2003     

Polymer blends of poly(ethylene‐2,6‐naphthalate) with polystyrene compatibilized by styrene‐glycidyl methacrylate copolymers. I. Rheology,morphology, and mechanical properties

The compatibilization of blends of poly(ethylene‐2,6‐naphthalate) (PEN) with polystyrene (PS), through the styrene‐glycidyl methacrylate copolymers (SG) containing various glycidyl methacrylate (GMA) contents, was investigated in this study. SG copolymers are able to react with PEN terminal groups during melt blending, resulting in the formation of desirable SG‐g‐PEN copolymers in the blend. These in situ formed copolymers tend to reside along the interface preferentially as the result of interfacial reaction and thus function as effective compatibilizers in PEN/PS blends. The compatibilized blends exhibit higher viscosity, finer phase domain, and improved mechanical properties. It is found that the degree of grafting of the in situ formed SG‐g‐PEN copolymer has to be considered as well. In blends compatibilized with the SG copolymer containing higher GMA content, heavily grafted copolymers would be produced. The length of the styrene segment in these heavily grafted copolymers would be too short to penetrate deep enough into the PS phase to form effective entanglements, resulting in the lower compatibilization efficiency in PEN/PS blends. Consequently, the in situ formation of SG‐g‐PEN copolymers with an optimal degree of grafting is the key to achieving the best performance for the eventually produced PEN/PS blends through SG copolymers. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 967–975, 2003     

Graphene nanoplatelet‐reinforced semi‐crystal poly(arylene ether nitrile) nanocomposites prepared by the twin‐screw extrusion

Graphene nanoplatelet reinforced semi‐crystal poly(arylene ether nitrile) (PEN/GN) nanocomposites were prepared by an economically and environmentally friendly method of twin‐screw extrusion technique. The feasibility of using PEN/GN nanocomposites was investigated by evaluating their thermal behaviors, mechanical, and morphological properties. Thermal studies revealed that GN could act as nucleating agents but decreased the whole crystallinity in/of PEN/GN nanocomposites. Mechanical investigation manifested that GN had both strengthening effect (increase in flexural modulus and strength) and toughening effect (rise in the elongation and impact strength) on the mechanical performance of semi‐crystal PEN nanocomposites. Heat treatment can further increase their mechanical performances due to the increased crystallinity and release of inner stress. With the small addition of GN (<5 wt%), the morphology of PEN was changed from brittle to ductile, and GN showed good dispersion and adhesion in/to the PEN matrix. This work shows that in the semi‐crystal polymer/filler systems, besides the dispersion states of fillers and interactions between fillers and polymer matrices, the crystallinity of the nanocomposites affected by the existence of filler and the residual stress are also two key factors determining the mechanical properties. POLYM. COMPOS., 35:404–411, 2014. © 2013 Society of Plastics Engineers     

Effect of polyarylene ether nitriles on processing and mechanical behaviors of phthalonitrile‐epoxy copolymers and glass fiber laminated composites

A series of copolymers and glass fiber composites were successfully prepared from 2,2‐bis [4‐(3,4‐dicyanophenoxy) phenyl] propane (BAPh), epoxy resins E‐44 (EP), and polyarylene ether nitriles (PEN) with 4,4′‐diaminodiphenyl sulfone as curing additive. The gelation time was shortened from 25 min to 4 min when PEN content was 0 wt % and 15 wt %, respectively. PEN could accelerate the crosslinking reaction between the phthalonitrile and epoxy. The initial decomposition temperatures (T_i) of BAPh/EP copolymers and glass fiber composites were all more than 350°C in nitrogen. The T_g of 15 wt % PEN glass fiber composites increased by 21.2°C compared with that of in comparison with BAPh/EP glass fiber composite. The flexural strength of the copolymers and glass fiber composites reached 119.8 MPa and 698.5 MPa which increased by 16.6 MPa and 127.3 MPa in comparison with BAPh/EP composite, respectively. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Design and properties of polyarylene ether nitrile copolymers with improved elongation at break

Polyarylene ether nitrile (PEN) based on biphenol exhibits a high glass transition temperature of 216°C, a high tensile strength of 110 MPa, and low elongation at break of approximately 4%. A series of PEN random copolymers with improved elongation at break were synthesized using various bisphenol compounds and 2,6-dichlorobenzonitrile (DCBN). The resulting PEN random copolymers exhibited a high glass transition temperature and thermal stability up to 513°C in a nitrogen atmosphere. PEN copolymers were amorphous and could easily be cast into transparent films with a tensile strength of 97.93–117.88 MPa and tensile modulus of 2187.98–2558.44 MPa. Most importantly, elongation at break of these PEN copolymers was higher than 13%. PEN copolymer films had a dielectric constant of 3.77–3.89 at 1 kHz and extremely low dielectric loss (<0.02). At the same time, the breakdown strength of PEN was in the range of 137.92–198.19 kV/mm and energy storage density was in the range of 0.32–0.68 J/cm³. Excellent mechanical, thermal, and dielectric properties of PEN make it possible to use them as high-temperature resistant dielectrics to act on high-temperature resistant insulated cables.     

Effect of dialcohols on properties of poly(ethylene 2,6‐naphthalate) copolymers

Properties of poly(ethylene 2,6‐naphthalate) (PEN) and its copolymers containing diethylene glycol (DEG), propanediol (PD), butanediol (BD), and bisphenol A ethoxylate (BSA) were investigated. The copolymer composition was determined by ¹H‐NMR spectroscopy. It has a higher value than the feed composition due to the high volatility of ethylene glycol (EG). The melting temperature of the copolymers was gradually depressed with the increase of dialcohol in the composition. The complex viscosity of the copolymers did not depend on the molecular weight, but on the chemical structure. The complex viscosity of the copolymers containing 3 mol % of DEG, BD, and 5 mol % of BD was lower than that of PEN, and the mechanical properties were similar with the value of PEN. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 2900–2905, 1999     

Interrelationship of thermal and mechanical properties of poly(ethylene terephthalate)/poly(ethylene 2,6‐naphthalate)/graphene nanocomposites

In the present work, attempts were made to investigate the thermal and mechanical properties of melt‐processed poly(ethylene terephthalate) (PET)/poly(ethylene 2,6‐naphthalate) (PEN) blends and its nanocomposites containing graphene by using differential scanning calorimetry and tensile test experimenting. The results showed that crystallinity, which depends on a blend ratio, completely disappeared in a composition of 50/50. By introducing graphene to PET, even in low concentrations, the crystallinity of samples increased, while the nanocomposite of PEN indicated reverse behavior, and the crystallinity was reduced by adding graphene. In the case of PET‐rich (75/25) nanocomposite blends, by increasing the nano content in the blend, the crystallinity of the samples was enhanced. This behavior was attributed to the nucleating effect of graphene particles in the samples. From the results of mechanical experiments, it was found in PET‐rich blends that by increasing the PEN/PET ratio, the modulus of samples decreased, whereas in the case of PEN‐rich blends, a slight increment of modulus is seen as a result of the increment of the PEN/PET ratio. The two contradicting behaviors were attributed to the reduction of crystallinity of PET‐rich blends by enhancement of PEN/PET ratio and the rigid structure of PEN chains in PEN‐rich blends. Unlike the different modulus change of PET‐rich and PEN‐rich blends, the nanocomposites of these blends similarly indicated an increment of modulus and characteristics of rigid materials by increasing the nano content. Furthermore, the same behavior was detected in nanocomposites of each polymer (PET and PEN nanocomposites). The alteration from ductile to rigid conduction was related to the impedance in the role of graphene plates against the flexibility of polymer chains and high values of graphene modulus. J. VINYL ADDIT. TECHNOL., 23:210–218, 2017. © 2015 Society of Plastics Engineers     

Aromatic liquid crystalline copolyesters with low Tm and high Tg: Synthesis,characterization, and properties

In this study, a series of aromatic copolyesters P‐BPAx with lower melting temperature and higher glass transition temperature derived from hydroxybenzoic acid (HBA), 6‐hydroxy‐2‐naphthoic acid (HNA), bisphenol A (BPA) and terephthalic acid (TA) were synthesized via melt polymerization. The copolyesters were characterized by FTIR, solid state ¹³C NMR, DSC, TGA, polarized optical microscopy, X‐ray diffraction, and rheometry measurements. With addition of BPA, the resulting copolyester's melting temperature decreased from 260 to 221°C and its glass transition temperature increased from 70 to 135°C, compared with the parent copolyester P‐HBA70 (HBA/HNA copolymer). With exception of copolyester P‐BPA5.0 (225–280°C), the copolyesters could maintain liquid crystalline behavior in a broad temperature range from 230°C to higher than 410°C. The ability to form nematic liquid crystalline phase disappeared when BPA concentration became higher than 15 mol %. X‐ray diffraction analysis showed crystallinity decreased as the BPA content increased. A slightly distorted O" and a substantially distorted O′ orthorhombic phase was observed for P‐BPA2.5. Upon annealing at 220°C, the O" phase disappeared and the O′ phase became stronger gradually. Rheology study data showed the ability to process the copolyesters improved in those compositions containing <2.5 mol % BPA. Continuing to increase concentrations of BPA, they became intractable. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40487.     

Effect of MWNTs concentration and cooling rate on the morphological,structural, and electrical properties of non‐isothermally crystallized PEN/MWNT nanocomposites

The effect of multiwall carbon nanotubes (MWNT) concentration and cooling rate on the morphological, structural and electrical properties of non‐isothermally crystallized Poly(ethylene naphthalate) nanocomposites (PEN/MWNT) was studied. PEN/MWNT nanocomposites containing 1 and 2 wt % of nanotubes were prepared by melt blending in a mini twin screw extruder. Nanocomposite samples with different degree of crystallinity (X_c) were obtained via non‐isothermally crystallization at cooling rates of 2, 10, 20, and 300°C min^?1. In this study it was demonstrated that carbon nanotubes and cooling rate strongly influence morphological and structural characteristics of PEN. Calorimetric results showed that the peak crystallization temperature (T_c) of PEN nanocomposites was increased ～9° through heterogeneous nucleation with respect to pure PEN. X‐ray diffraction revealed that carbon nanotubes modify the crystalline structure of PEN favoring the formation of β‐crystals, and this effect increases with the nanotubes content. On the basis of X‐ray scattering analysis, the variation of lamellar thickness revealed that nanotubes promote the formation of lamellar crystals with average thickness of 20 nm at different cooling rates. These structural and morphological changes play an important role on the electrical properties of nanocomposites. It was found that higher concentration of nanotubes and crystallinity promotes electrical conductivity of nanocomposites in the order of semiconductors (until 1 × 10^?4 S cm^?1) as well as permittivity of 20 at different tested frequencies. This may due to the interconnected networks of nanotubes throughout the crystalline structure formed in PEN nanocomposites. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41765.     

The influence of cross‐linking reaction on the mechanical and thermal properties of polyarylene ether nitrile

The processing of cross‐linked polyarylene ether nitrile (PEN), which has a triazine rings structure, has been investigated under different reaction times and temperatures. In this study, the PEN films prepared by the tape‐casting formed the thermally stable triazine rings by catalytic cross‐linking reaction gradually, which was characterized by Fourier transform infrared spectroscopy. The chemical cross‐linking reaction occurred as the CN group absorption of PEN at 2221 cm⁻¹ decreased and a new absorption peak, at 1682 cm⁻¹, was observed, and the absorption peak intensity would be progressively larger, with the extension of the processing time. After the formation of cross‐linking networks, the cross‐linking degree and thermal and mechanical properties of the processed films were improved substantially, compared with the untreated films. The film with added ZnCl₂ as the catalyst was more rapidly cross‐linked, and its properties were better than that without catalyst at the same treatment conditions. The glass‐transition temperature (T_g) of PEN films processed at 350°C for 4 h (213.65°C) was higher than that of PEN films before the treatment (161°C), and the tensile strength was also improved significantly. The PEN was processed at 350°C for 2 h, whose initial decomposition temperature increases by about 10°C, compared with that of untreated film, at one time. The rheology behavior of the cross‐linked films was processed on dynamic rheometer to monitor and track the process of polymer cross‐linking reaction. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis and properties of organic soluble semicrystalline poly(aryl ether ketone)s copolymers containing phthalazinone moieties

A series of poly(aryl ether ketone)s (PAEK) copolymers containing phthalazinone moieties were synthesized by modest polycondensation reaction from 4‐(4‐hydroxyl‐phenyl)‐(2H)‐phthalazin‐1‐one (DHPZ), hydroquinone (HQ), and 1,4‐bis(4‐fluorobenzoyl)benzene (BFBB). The T_g values of these copolymers ranged from 168 to 235°C, and the crystalline melting temperatures varied from 285 to 352°C. By introducing phthalazinone moieties into the main chain, the solubility of these copolymers was improved in some common polar organic solvents, such as chloroform (CHCl₃), N‐methyl‐2‐pyrrolidinone (NMP), nitrobenzene (NB) and so on. The values of 5% weight loss temperatures were all higher than 510°C in nitrogen. The crystal structures of these copolymers were determined by wide‐angle X‐ray diffraction (WAXD), which revealed that they were semicrystalline in nature, and the crystal structure of these copolymers was orthorhombic, equal to poly(ether ether ketone ketone)s. As phthalazinone content in the backbone varied from 0 to 40 mol % (mole percent), the cell parameters of these copolymers including the a, b, and c axes lengths ranged from 7.76 to 7.99 Å, 6.00 to 6.14 Å, and 10.10 to 10.19 Å, respectively. The degree of crystallinity (via differential scanning calorimetry) decreased from 37.70% to 16.14% simultaneously. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 1744–1753, 2007     

Copolymers of poly(arylene sulfide sulfone)/poly(ether sulfone): Synthesis,structure, and rheology properties

In order to overcome the poor flowability of poly(arylene sulfide sulfone) (PASS), we introduced ether bonds into the polymer main chain. A series poly(arylene ether sulfide sulfone) copolymers (PAESS) containing different proportion of ether bonds were synthesized with 4,4′‐dichlorodiphenyl sulfone (DCDPS), sodium sulfide (Na₂S·xH₂O), and 4,4′‐dihydroxydiphenyl ether (DHDPE). The copolymers were characterized by Fourier transform infrared (FTIR), ¹H‐nuclear magnetic resonance (NMR), differential scanning calorimetry, dynamic mechanical analysis (DMA), and rheometer. The results of FTIR and ¹H‐NMR indicate the copolymers are synthesized successfully. PAESS were found to have excellent thermal properties with glass transition temperature (T_g) of 175.7–219.1 °C and 5% weight lost temperature were all above 420 °C. The tensile and DMA test indicates that these resultant copolymers have good mechanical properties with tensile strength of 60 MPa and storage modulus of 1.5 GPa. From the results of rheology properties testing, we found that the melt stability and melt flowability of PASS were improved distinctly from 25,470 Pa s down to 355 Pa s with the incorporation of ether bonds. That will be quite beneficial to the processing of PASS, especially for the thermoforming of precision products. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46534.     

In situ compatibilization of PEN/LCP blends by ultrasonic extrusion

In situ compatibilization of immiscible blends of PEN and thermotropic LCP was achieved by the ultrasonically‐aided extrusion process. Ultrasonically‐treated PEN underwent degradation, leading to a decrease of its viscosity. Viscosity of LCP was unaffected by ultrasonic treatment. Because of reduced viscosity ratio of PEN to LCP at high amplitude of ultrasonic treatment, larger LCP domains were observed in molding of the blends. LCP acted as a nucleating agent, promoting higher crystallinity in PEN/LCP blends. Ultrasonically‐induced copolymer formation was detected by MALDI‐TOF mass spectrometry in the blends. Ultrasonic treatment of 90/10 PEN/LCP blends improved interfacial adhesion in fibers spun at intermediate draw down ratios (DDR), improving their ductility. The lack of improvement in the mechanical properties of fibers spun at high DDR after ultrasonic treatment was attributed to the disturbance of interfacial copolymer by high elongation stresses. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.