A note on the similarity solutions for free convection on a vertical plate

Summary The similarity solutions for free convection on a vertical plate when the (non-dimensional) plate temperature is x and when the (non-dimensional) surface heat flux is –x are considered. Solutions valid for 1 and 1 are obtained. Further, for the first problem it is shown that there is a value ₀, dependent on the Prandtl number, such that solutions of the similarity equations are possible only for >₀, and for the second problem that solutions are possible only for >–1 (for all Prandtl numbers). In both cases the solutions becomes singular as ₀ and as –1, and the natures of these singularities are discussed.     

The athermal α → ω transformation in Zr-2 at% Nb alloy

The athermal transformation in Zr-2 at.% Nb alloy has been investigated by transmission electron microscopy. Analysis of the selected-area diffraction pattern has shown that the orientation relationships between the omega and the parent-phase in quenched Zr-2 at.% Nb alloy are the same as have been previously observed for the reaction in pure zirconium. Thus it was deduced that the direct transition has taken place in the alloy during cooling. The-originated -particles were visualized using the dark-field technique. The formation of the athermal omega in the-region of-stabilized Zr-Nb alloy is discussed in terms of the relative positions of the free energy equilibrium curvesT ₀ ,T ₀ ,T ₀ and the correspondingM _s ,M _s andT _s start curves. It is concluded that the omega phase can occur over a much wider range of alloy compositions than is usually recognized on the basis of transformation data.     

Differential-flow-induced instability in a cubic autocatalator system

The formation of spatio-temporal stable patterns is considered for a reaction-diffusion-convection system based upon the cubic autocatalator, A + 2B 3B, B C, with the reactant A being replenished by the slow decay of some precursor P via the simple step P A. The reaction is considered in a differential-flow reactor in the form of a ring. It is assumed that the reactant A is immobilised within the reactor and the autocatalyst B is allowed to flow through the reactor with a constant velocity as well as being able to diffuse. The linear stability of the spatially uniform steady state (a, b) = (µ^–1, µ), where a and b are the dimensionless concentrations of the reactant A and autocatalyst B, and µ is a parameter reflecting the initial concentration of the precursor P, is discussed first. It is shown that a necessary condition for the bifurcation of this steady state to stable, spatially non-uniform, flow-generated patterns is that the flow parameter > _c(µ, ) where _c(µ,) is a (strictly positive) critical value of and is the dimensionless diffusion coefficient of the species B and also reflects the size of the system. Values of _c at which these bifurcations occur are derived in terms of µ and . Further information about the nature of the bifurcating branches (close to their bifurcation points) is obtained from a weakly nonlinear analysis. This reveals that both supercritical and subcritical Hopf bifurcations are possible. The bifurcating branches are then followed numerically by means of a path-following method, with the parameter as a bifurcation parameter, for representatives values of µ and . It is found that multiple stable patterns can exist and that it is also possible that any of these can lose stability through secondary Hopf bifurcations. This typically gives rise to spatio-temporal quasiperiodic transients through which the system is ultimately attracted to one of the remaining available stable patterns.     

Amplifier based on a field-effect triode with negative current feedback

Conclusions A field-effect triode amplifier with series negative current feedback allows a voltage gain of the order of 200–300 to be obtained for a load resistance R_s1 M. The coefficient K_u begins to decrease noticeably only for a feedback resistance above 500 .The current gain reaches (8–10)·10³. Increasing the resistances R_s and R_L to hundreds of ohms has practically no effect on K_i. For a further increase of R_s and R_L the coefficient K_i decreases.The power gain reaches its maximum value (of the order of 10⁴ or more) for R_s100 and R_L=10–100 k. An increase in R_s leads to a reduction of K_pmax and to a shift of the extremum of the function K_p=f(R_L) into the range of higher values of R_L.A large input resistance of the amplifier (tens of megohms and higher) is obtained when R_s increases to 10–100 M. The maximum input resistance is obtained for R_L and R_s and may exceed values of from hundreds of megohms to several gigaohms. The minimum input resistance is hundreds of kilohms for R_L and R_s0.The minimum input resistance (5–10 k or less) is ensured for R_g and R_L0. An increase of the output resistance to hundreds of megohms or higher occurs for R_g and R_s.Translated from Izmeritel'naya Tekhnika, No. 9, pp. 67–70, September, 1971.     

Study of the paramagnetic-antiferromagnetic transition and the γ → ε martensitic transformation in Fe-Mn alloys

The paramagnetic-antiferromagnetic transition and the martensitic transformation of Fe-Mn (Mn 15–32 wt%) alloys have been investigated by resistivity, dilatometry and X-ray diffraction (XRD). The results show that paramagnetic-antiferromagnetic transition increases the resistivity and the volume of alloys, whereas the martensitic transformation reduces the resistivity and volume of alloys. The A _f that was determined by the dilatometric method is not the temperature that martensites in the Fe-Mn alloys have reverse transformed to austenites completely. Mn additions reduce M _s, increase T _N and the lattice parameter of austenite in the Fe-Mn alloys. Both the antiferromagnetic transition and the martensitic transformation lead to an increase in the lattice parameter of austenite. The lattice parameters both above T _N and below T _N decrease linearly with temperature. The lattice parameter below M _s increases first and then decreases. Moreover, the (110) and (002) atomic planes in the Fe-15Mn-0.15C alloy are separated into two peaks: 2 for (002) is 44.16°, 2 for (110) is 44.47°.     

Ultrasonic attenuation of longitudinal and shear waves in superconducting lead

Longitudinal and shear wave ultrasonic attenuations have been measured in high-purity Pb on two single crystals obtained from the same ingot. The measurements were done at low temperatures, at different frequencies, and in transverse magnetic fields, up to a field of 7.3 kG. The propagation directions in the two crystals were along [100] and [110]. For some propagation and polarization directions the _s / _n ratio is found to be frequency-independent, while for others, large divergences in the _s / _n ratios at different frequencies are observed. A sharp decrease of _s / _n nearT _c is observed for a particular longitudinal wave propagation, but not in any shear wave propagation. In some cases _s / _n is found to be abnormally high and this feature is associated with a peak in attenuation _n and a relatively high _n at 7.2 K. None of the _s / _n curves fits closely to any BCS energy gap. For longitudinal waves the high magnetic field (H) dependence of the normal state attenuation was found to agree qualitatively with the free electron theory for propagation along [100], but not for propagation along [110]. For shear waves the high-field attenuations do not extrapolate to zero asH tends to infinity. For all propagation and polarization directions the high-field attenuations show 1/H ² field dependence.     

Ageing characteristics of cast Zn-Al based alloy (ZnAl7Cu3)

Microstructure and ageing characteristics of a cast Zn-Al based alloy (ZnAl7Cu3) were studied using X-ray diffraction, electron scanning microscopy and back-scattered diffraction techniques. Two stages of phase transformation, i.e., decomposition of zinc rich phase and four phase transformation, + T + , were detected during ageing at 150°C. Electron back-scattered diffraction technique was applied in distinguishing both zinc rich and phases.     

On the flow of a stratified fluid over a barrier

Summary The flow of a stratified fluid over a barrier is considered. The initial-value problem is solved, and it is shown that there is no disturbance far upstream of the barrier whent . The stationary solution which is obtained by lettingt, is given in a simple closed form for a barrier of an arbitrary shape.     

Complex Model of the Efficiency of Rectification Plates. 8. Comparison with Other Models with Respect to Experimental Data

A complex model is compared with the Murphree and Hausen models for the cases of concurrent and cross motion of vapor and liquid phases. Use is made of results of experimental studies involving separation of an acetic acidwater mixture and industrial data on rectification of furfurol and ethanol. It is proved that the efficiencies in the complex and Murphree models coincide as the coefficient of phase equilibrium m approaches unity but when this coefficient increases, the first model and the Hausen model coincide. The possibility of using the Murphree model at m 1 and the Hausen model at m is shown.     

Subgap peak and Tomash-McMillan-Anderson oscillations in the density of states of SNS Bridges

The quasiparticle spectra and the densities of states of superconducting-normal-superconducting junctions are computed from the WKBJ transformed Bogoliubov-de Gennes Equations (BdGE), which are solved by Picard iteration and numerical integration. It is shown that the influence of the proximity effect on the bound states can be modeled by a rectangular pair potential well of effective normal layer thickness 2a*= _–L ^L [1–(z)/]dz, where (z) is the pair potential of the junction, is its asymptotic constant value, and 2L is the total length of the sample. The density of states exhibits a subgap peak at energies less than besides the BCS peak atE=; forE> there are geometrical resonances which are due to electron-hole interferences in finiteS layers of thicknessL-a*.     

Continuous,martensitic nature of the transition ß→γ Li3PO4

The transformation Li₃PO₄ shows characteristics of both continuous and martensitic transformations. Below 340° C, no detectable transformation occurs; between 340 and 410° C, the transformation goes only partially to completion; above 410° C the transformation rapidly goes to completion. At any temperature in the range 340 to 410° C, transformation proceeds rapidly in the initial stages to attain a certain degree of transformation. With prolonged isothermal heating or grinding of the samples, further transformation does not occur. The reverse transformation could not be effected under normal, dry conditions.     

Theory of RF SQUIDs Operating in the Presence of Large Thermal Fluctuations

A comprehensive analytical theory is presented for non-hysteretic RF SQUIDs operating in the adiabatic mode in the presence of large thermal fluctuations. When 1 ( = 2LI_c/₀ is the hysteresis parameter, L is the SQUID inductance, I_c is the critical current of the Josephson junction, and ₀ is the flux quantum) the theory is applicable also for RF SQUIDs operating in the non-adiabatic mode. In contrast to previous theories in which the noise is treated perturbatively and which therefore are applicable only if the product 1 ( = 2k_BT/ ₀ I_c is the noise parameter, k_B is the Boltzmann constant, and T is the absolute temperature)—the case of small thermal fluctuations—the present theory is valid for around unity or higher. In the limit 0 the theory reproduces the results of small thermal fluctuations theories. It has been found that in the presence of large thermal fluctuations the screening current in the SQUID inductance is suppressed by a factor that increases with increasing . Taking into account this new basic fact, all SQUID characteristics (output signal, transfer function, noise spectral density and energy sensitivity) have been recalculated and a good agreement with experimental data has been obtained. It has been also found that RF SQUIDs can be operated with substantially higher values of the inductance and of the noise parameter than DC SQUIDs. These two aspects, which are of particular importance at liquid nitrogen temperature, make high T_c RF SQUIDs very attractive.     

Axisymmetric stagnation-point flow impinging on a transversely oscillating plate with suction

The viscous fluid motion generated by axisymmetric stagnation-point flow of strain rate a impinging on a flat plate oscillating in its own plane with velocity amplitude U0 and frequency , including uniform suction of strength W0 is considered. A coordinate decomposition transforms the full Navier-Stokes equations into a primary equation describing the steady flow and a secondary equation describing the unsteady motion coupled to the primary solution. The solution to the boundary-value problem is governed by two dimensionless groups: the suction parameter S = W0 a and the frequency parameter = /a, where is the kinematic viscosity. Numerical integrations performed with a Runge-Kutta routine provide an exact solution to the Navier-Stokes equations. Values of the steady shear stress are found to agree with asymptotic results for large values of |S|, with S>0 representing suction and S<0 representing blowing. The magnitude and phase of the unsteady shear stress are given over a range of frequencies sufficient to recover analytical asymptotic results at large values of . The unsteady shear stress lags the wall motion by radians for 0 and by 5/4 radians when . Velocity profiles at selected parameter values during a period of plate oscillation are presented and discussed.     

Transport properties of helium near the liquid-vapor critical point. II. Thermal conductivity of a3He-4He mixture

Measurements of the thermal conductivity are reported for an 80%³He-20%⁴He mixture above the critical point along several isotherms and near-critical isochores, using the same techniques and apparatus described for a study of³He. Using again the assumption that the observed conductivity can be decomposed into a sum of a regular and a singular contribution _reg and _sing, it is shown that along two near-critical isochores, _sing diverges. In particular, along the isochore showing the largest at the phase transition, the divergence is nearly the same as for³He and can be roughly characterized by a simple power law (T-T_c)^– with 0.58. This observation is contrary to predictions that foresee _sing0 asT _c is approached. The relaxation times characterizing the attainment of steady state conditions after switching the heat flux on and off show a similar behaviour as a function of reduced temperature as do those for pure³He. This result might indicate a substantial coupling between concentration and entropy diffusion. In the Appendix, the correlation length for³He nearT _c is calculated from heat conductivity, viscosity, and specific heat data.Work supported by Grant DMR 8024056 of the National Science Foundation.     

Transport results from untwinned YBCO: Washboard frequency of the vortex lattice,and the quasiparticle mean free path

The washboard frequency of the moving vortex lattice in untwinned YBa₂ Cu₃ O_6.93 may be observed through mode-locking to an externally applied ac current of frequency _ext. The interference between and _ext results in jumps in the dc current-voltage characteristics when and _ext are harmonically related¹. The interference effect disappears in the vortex liquid state. The Hall conductivity _xy below T_c in YBCO contains contributions² from a positive quasiparticle (qp) term (H) and a negative vortex term (1/H). The qp term is surprisingly large well below T_c and implies a large gap anisotropy and a long qp mean free path (mfp). The thermal Hall effect³ _xy is closely related to the qp _xy; _xy is produced by asymmetric scattering of qp by pinned vortices. The qp mfp at H = 0, extracted from _xy and extended to low T by _xy, increases remarkably from 90 Å at T_c to more than 0.5m at 22 K.     

Investigation of the gapless state in bismuth-antimony alloys

The results are presented from an experimental study of the gapless state produced in semiconducting alloysBi _1–x Sb _x by pressure-induced band inversion. The magnetoresistance properties of the alloys have been investigated both in weak magnetic fields (H « 1) and in strong fields (H75 kOe) at liquidhelium temperatures in the Sb concentration interval 0.06x0.15 and pressure interval 1 bar p<20 kbar. At pressuresp close to the pressurep _k at which the gapless state is realized a semiconductor-semimetal-semiconductor transition is detected inBi _1–x Sb _x alloys withx=0.070 and 0.071. The rates of change of the gap _gL before and after inversion are determined: –(2.5±0.5)×10^–6 eV/bar and (1.5±0.5)×10^–6 eV/bar, respectively. A reduction in the carrier effective mass as _gL 0 is observed down to values of 10^–4 m ₀. It is shown that as _gL 0 the carrier mobilities in the alloys increase abruptly, the effect being a maximum in the purest alloys, where forT=4.2 K the mobility along the binary axis attains the record-high value of 3×10⁸ cm²/V · sec.     

Anisotropic grain growth of R-α-sialon (R = Nd and Er)

Two R--sialon (R_0.6Si_9.3Al_2.7O_0.9N_15.1, R=Nd and Er) compositions were first fired at 1750°C/25 min and 1650°C/2 h respectively for completion of the phase transformation. Elongated -sialon grain morphology was developed in both samples after being re-fired at 1800°C for different periods of time. The growth in width of R--sialon grains is controlled by diffusion in the liquid, while the length growth tends to be interfacial reaction controlled. The anisotropic growth of R--sialon is attributed to the large difference in the growth rate constant between the length and the width directions of the grain.     

Structure and decomposition behaviour of rapidly solidified AI-Cu-Li-Mg-Zr alloys

The microstructural characteristics of AI-Cu-Li-Mg-Zr alloys have been studied after rapid solidification by melt spinning and after subsequent annealing at temperatures in the range 160 to 500°C, by using a combination of optical microscopy, scanning and transmission electron microscopy, X-ray diffraction, differential scanning calorimetry and microhardness measurements. The as-melt-spun alloys consist of a cellular microstructure with fine scale precipitates and icosahedral particles distributed within the cells and at cell boundaries. The icosahedral structure is equivalent to the T₂ phase reported by Hardy and Silcock. Annealing the melt-spun alloys leads to a complex precipitation sequence: + I + + I + S + + I + + T₁ + T₂ (bcc) + two other phases. The icosahedral particles coarsen progressively during annealing, especially at higher annealing temperatures. Fine-scale precipitates grow during annealing at low temperature, dissolve at higher annealing temperatures below 500°C, and then reprecipitate during cooling after annealing at 500°C. During annealing at low temperature, plates of and S precipitate and then dissolve, providing solute atoms for icosahedral particle growth. Stable T₁, T₂ (bcc) and two other phases precipitate after decomposition of the icosahedral particles during annealing at 500°C.     

Order parameters and energies of analytic and singular vortex lines in rotating3He-A

We present the expressions of the generalized Ginzburg-Landau (GL) theory for the free energy and the supercurrent in terms of thed vector, the magnetic fieldH, and operators containing the spatial gradient and the rotation. These expressions are then specialized to the Anderson-Brinkman-Morel (ABM) state. We consider eight single-vortex lines of cylindrical symmetry and radiusR=[2m/]^–1/2: the Mermin-Ho vortex, a second analytic vortex, and six singular vortices, i.e., the orbital and radial disgyrations, the orbital and radial phase vortices, and two axial phase vortices. These eight vortex states are determined by solving the Euler-Lagrange equations whose solutions minimize the GL free energy functional. For increasing field, the core radius of the texture of the Mermin-Ho vortex tends to a limiting value, while the core radius of the texture goes to zero. The gap of the singular vortices behaves liker forr 0, where ranges between and . The energy of the radial disgyration becomes lower than that of the Mermin-Ho vortex for fieldsH6.5H*=6.5×25 G (atT=0.99T _c and forR=10L*=60 µm, or=2.9 rad/sec). ForR 2 _T ( _T is the GL coherence length) or _c2 (upper critical rotation speed), the energies of the singular vortices become lower than the energies of the analytic vortices. This is in agreement with the exact result of Schopohl for a vortex lattice at _c 2. Finally, we calculate the correction of order (1 -T/T _c ) to the GL gap for the axial phase vortex.     

Transport in the low-temperature limit of a Landau Fermi liquid

The Boltzmann equation for Landau quasiparticles is solved for T 0 by a specialization of a method discussed by Sykes and Brooker. The quasiparticle distribution function is expanded in Legendre polynomials, assuming a boundary condition which imposes axial symmetry, and even-order terms are assumed to relax together with relaxation time _e , odd-order terms with relaxation time _o . By letting wavelength , with finite, one obtains a first-sound solution, and by lettingT 0, and then , one obtains a zero-sound solution. When these solutions are used to calculate the pressure, it is found that the first-sound solution is consistent with hydrodynamics, exhibiting viscosity = _s , while the zero-sound velocityc ₁=[^–1(B₁+4/3_s)]^1/2, so that phenomenologically zero-sound propagates like a longitudinal elastic wave in a glass. A higher zero-sound mode is also predicted, but is heavily damped. The heat flux is calculated and found to obey Vernotte's equation, which contains an intertial term, added to Fourier's law, that becomes significant asT 0.