Supercritical carbon dioxide extraction of Capsicum peppers: Global yield and capsaicinoid content

The objective of this study was to select a variety of pepper with high concentration of capsaicin and subject it to supercritical fluid extraction (SFE), in order to determine the best conditions of temperature (40, 50 and 60 °C) and pressure (15, 25 and 35 MPa) in terms of global yield (X₀) and capsaicinoids content of the extracts. The influence of drying process (freeze and oven drying) on X₀, capsaicin (C) and dihydrocapsaicin (DHC) contents and total phenolics was also analyzed. Capsicum frutescens showed the highest levels of capsaicinoids (1516 μg/g fresh fruit). For the responses C and DHC, the extraction conditions of 15 MPa and 40 °C provided the highest concentrations (C ⿿ 42 mg/g extract and DHC ⿿ 18.5 mg/g extract). The freeze drying process resulted in extracts with the highest concentration of capsaicinoids (61 mg/g extract), but in contrast, the phenolics were less susceptible to different drying processes, with a mean concentration of 35 mg GAE/g extract. The kinetics experiments indicated that the extraction rate of oleoresin was slightly slower than that of capsaicinoids at the operation conditions (40 °C and 15 MPa).     

Water and ethanol as co-solvent in supercritical fluid extraction of proanthocyanidins from grape marc: A comparison and a proposal

Supercritical carbon dioxide (SC-CO₂) extraction of grape marc was studied using water (W) and ethanol (EtOH) as co-solvent at 15% (w/w), 100 and 200 MPa, and 313.15, 323.15 and 333.15 K to analyze their influence upon total phenols of the extracts. The overall extraction curves were determined and suggested 10 MPa and 313.15 K as the best operating conditions for SC-CO₂ + 15%W extraction, and 10 MPa and 333.15 K for SC-CO₂ + 15% EtOH. The phenolic yields obtained were 63.4 g/kg of extract for SC-CO₂ + 15% W and 38.8 g/kg of extract for SC-CO₂ + 15% EtOH. An alternative method combining Sc-CO₂ + 15% W extraction, followed by SC-CO₂ + 15% EtOH was tested. This procedure provided the best results allowing to obtain the highest phenolic yield (68.0 g/kg of extract), phenol content (733.6 mg GAE/100 g DM), proanthocyanidins concentration (572.8 mg catechin/100 g DM) and antioxidant activity (2649.6 mg α-tocopherol/100 g DM). SC-CO₂ methods were compared with methanol extraction.     

Obtaining phenolic compounds from jatoba (Hymenaea courbaril L.) bark by supercritical fluid extraction

The extraction of polyphenol compounds from jatoba (Hymenaea courbaril L. var stilbocarpa) bark using supercritical fluid extraction (SFE) with CO₂ and cosolvents has been investigated. Among the solvent systems studied, SFE using CO₂ and water (9:1, v/v), at 323 K and 35 MPa, presented the best results, with extract yield of 24%, and with high antioxidant activity (IC₅₀ of 0.2 mg/cm³). This solvent system was used to determine global yield isotherms, which were built at 323 and 333 K, and 15, 25, and 35 MPa, using a second lot of jatoba. The highest yield was 11.5% at 15 MPa and 323 K, with maximum total phenolic compounds (TPC) of 335.00 mg TAE/g extract (d.b.) and total tannins content of 1.8 g/100 g raw material. A kinetic experiment was performed using optimized conditions, yielding 18% extract, and the kinetic parameters were used to scale-up the process from laboratory to pilot scale. Chemical analyses showed high content of phenolic compounds in the extracts of jatoba bark mostly due to the presence of procyanidins.     

Extraction of protocatechuic acid from Scutellaria barbata D. Don using supercritical carbon dioxide

The use of supercritical carbon dioxide (SC⿿CO₂), with water as a modifier, was evaluated in this study as a method to extract protocatechuic acid (PA) from Scutellaria barbata D. Don. The highest extraction yield of PA, 64.094 ± 2.756 μg/g of dry plant, was achieved at 75 °C and 27.5 MPa, with the addition of 15.6% (v/v) water as a modifier. The mean particle size was 0.355 mm, the CO₂ flow rate was 2.2 mL/min (STP) and the dynamic extraction time was 100 min. At pressures of 16.2⿿30.0 MPa and temperatures of 45⿿75 °C, the mole fraction solubilities of PA in SC⿿CO₂ ranged from 2.829 ÿ 10^⿿7 to 9.631 ÿ 10^⿿7. The solubility data for PA fit well in the Chrastil model. It is evident that the SC⿿CO₂ extraction uses less solvent, saves both energy and time and is an environmentally friendly extract technology that can be used in the food, cosmetic and pharmaceutical industries.     

Cosolvent-modified supercritical carbon dioxide extraction of phenolic compounds from bamboo leaves (Sasa palmata)

This study highlights the possibility of supercritical carbon dioxide for extracting phenolic compounds from bamboo leaves that have shown antioxidant and anticancer activities. The CO₂ extraction solvent was modified by adding ethanol–water mixture cosolvent of different concentrations to allow extraction of both polar and non-polar compounds. Conventional Soxhlet extraction was also done to investigate the advantages of supercritical extraction over the conventional extraction method. For addition of 5% (mol) of a 25:75 (mol:mol) ethanol–water mixture solvent to CO₂, the highest amount of polyphenols (7.31 ± 0.06 mg/g bamboo leaves in catechin equivalents) and radical scavenging activity (3.65 ± 0.05 mg/g bamboo leaves in BHA equivalents) at 20 MPa and 95 °C, could be obtained among the mixture cosolvents studied. For Soxhlet extraction with a 25:75 (mol:mol) ethanol–water mixture, 1.48 times the amount of phenolic compounds (10.85 ± 0.52 mg/g bamboo leaves in catechin equivalents), could be isolated compared with the supercritical extraction method, however, the radical scavenging activity (3.30 ± 0.05 mg/g bamboo leaves in BHA equivalents) was 0.90 times lower than the extract obtained from the supercritical extraction method. The seven major antioxidative compounds identified from the SC-CO₂ extraction method were: (1) dl-alanine, (2) gluconic acid, (3) phosphoric acid, (4) ß-siosterol, (5) β-amyrene, (6) α-amyrin acetate and (7) friedelin.     

Integrated supercritical fluid extraction and subcritical water hydrolysis for the recovery of bioactive compounds from pressed palm fiber

Pressed palm fiber (PPF), a residue obtained from palm oil industry, is a source of bioactive compounds, such as carotenoids, which are used as food additives. It also has cellulose and hemicellulose that can be used to yield fermentable sugars for the production of second generation ethanol. Supercritical fluid extraction (SFE) of pressed palm fiber provides an oil rich in carotenoids while subcritical water hydrolysis (SubWH) produces hydrolysates with high amounts of fermentable sugars. In this work, the effects of pressure (15–30 MPa) and temperature (318 and 328 K) on SFE of carotenoids were investigated. The SFE extract with highest carotenoid content was obtained at 318 K and 15 MPa (2.3% d.b., 0.81 mg β-carotene/g extract). After the extraction, the influence of process temperature (423–633 K), pressure (15 and 25 MPa), solvent:feed ratio (120 and 240), and residence time (1.25–5 min) on SubWH of the extraction residue was studied. At the temperature of 523 K, the highest total reducing sugar yield (11–23 g glucose/100 g carbohydrate) and the highest biomass conversion (40–97%) were obtained for any pressure and solvent:feed ratio. The highest selectivity for saccharide formation was found at 423 K (20–59 mol glucose/mol furfural equivalent). Optimal conditions for high saccharide formation and low sugar degradation product in subcritical hydrolysis were obtained at 523 K, 15 MPa, solvent:feed ratio of 120, residence time of 2.5 min with a total reducing sugar yield of 22.9 g glucose/100 g carbohydrate and a conversion of 84.9%.     

Extraction of bioactive enriched fractions from Eruca sativa leaves by supercritical CO2 technology using different co-solvents

Supercritical fluid extraction from freeze-dried Eruca sativa leaves is assessed with the aim of studying the feasibility to obtain bioactive enriched fractions containing different classes of valuable compounds. Total extraction yields and compositions using pure CO₂ and CO₂ + selected co-solvents are compared. Overall extraction curves, fitted by the model of broken and intact cells developed by Sovová, are reported and the influence of the main parameters that affect the extraction process is analysed. The extract with the highest content in glucosinolates and phenols was collected at 30 MPa and 75 °C using 8% (w/w) of water with respect to the CO₂ flow rate, whereas the fraction richest in lipids was obtained using 8% (w/w) of ethanol as co-solvent at 45 °C and 30 MPa. A process including a first step with supercritical CO₂ extraction using water as co-solvent followed by a second step, where a fraction rich in lipids is extracted using ethanol as co-solvent, is proposed. SCCO₂ results are compared with Soxhlet and other methods that combine organic solvents with ultrasounds.     

Argon as a potential processing media for natural and synthetic substances

Phase equilibrium data of caffeine, vanillin, o-ethyl vanillin and a natural rosemary extract (containing 73.9% carnosic acid and 14.7% carnosol) in argon have been determined in present work.Solubility data were determined at temperatures of 313.15 K, 333.15 K and 363.15 K and in the pressure range from 0.82 MPa up to 50.27 MPa using a static–analytic method and were compared to solubility data of the same substances in CO₂.Maximal solubility of vanillin in argon was obtained at a temperature of 313.15 K and a pressure of 43.8 MPa, approx. 0.015 g/g. Comparing the solubility data of pure vanillin in argon and in CO₂ higher solubility in argon is observed at lower temperatures and pressures. For o-ethyl vanillin the solubility in argon is higher in comparison to solubility in CO₂ in the entire range of pressure, especially at higher temperatures_.Maximal solubility of caffeine in argon was observed at a temperature of 363.15 K 0.001361 g caffeine/g argon at 38.9 MPa. With increasing pressure solubility increases, while temperature does not have a noticeable impact in the temperature range from 313.15 K to 333.15 K; the solubility increased with increasing temperature to 363.15 K. Similarly, solubility of carnosic acid extract increases with increasing pressure, from about 0.0097 × 10⁻² g substance/g gas at 2.08 MPa and at 313.15 K to 0.0338 × 10⁻² g substance/g gas at 50.27 MPa and at 363.15 K.Solubility of the investigated compounds in argon is a function of both, pressure and temperature. Generally, pressure significantly impacts solubility particularly up to a pressure of 20.0 MPa in case of vanillin and up to 30 MPa in case of o-ethyl vanillin and carnosic acid extract. An additional increase of pressure has only a slight impact on solubility. In the case of caffeine, the impact of pressure on the solubility becomes more evident at pressures higher than 20 MPa.     

Density and viscosity of the binary polyethylene glycol/CO2 systems

Density of CO₂ saturated solutions of polyethylene glycols (PEGs) of different molecular weight was measured in pressure range from 8.0 MPa up to 47.7 MPa at a temperature of 343 K by a volumetric method. To validate the method density of pure CO₂ was measured at different pressures and a temperature of 293 K. The results were compared to the literature data and the accuracy was better than 2%. The density was between 1.17 g/mL for PEG 1000/CO₂ at 14.5 MPa and 1.78 g/mL for the system PEG 4000/CO₂ at 35 MPa. Further, the data were compared to results, obtained by a gravimetric method using magnetic suspension balance (MSB).Viscosity of CO₂ saturated solutions of polyethylene glycols (PEGs) of different molecular weight at different pressures and at a temperature of 343 K was measured using a high pressure view cell. Also a temperature impact on the viscosity of pure PEGs was observed at ambient pressure. After saturating PEG 1500 with 10 MPa of CO₂ pressure its viscosity decreases from 76.6 mPa s to 2.24 mPa s at 333 K. Further addition of CO₂ and increasing the pressure results in even lower viscosity and the highest viscosity reduction was reached at the highest pressure; at 35 MPa viscosity of the system PEG 1500/CO₂ is only 0.665 mPa s.     

Pressurized liquid extraction and low-pressure solvent extraction of carotenoids from pressed palm fiber: Experimental and economical evaluation

In this work, a comparison of Soxhlet extraction (LPSE–SOX), percolation (LPSE–PE) and pressurized liquid extraction (PLE) for the recovery of carotenoid-rich extracts from pressed palm fiber (PPF) was carried out in terms of yield, carotenoid profile and economic viability to evaluate the methods’ industrial applicability. An optimization study was performed for each extraction technique with ethanol at a solvent/feed ratio of 20. The independent variables were temperature (35–55 °C), pressure (0.1–8 MPa) and flow rate (1.6, 2.4 g/min). The results showed that the global extraction yield obtained using LPSE–SOX (96 ± 4 mg extract/g PPF d.b.) after 6 h was higher than that obtained using LPSE–PE (74 ± 5 mg extract/g PPF d.b., 35 °C, 2.4 g/min) or PLE (44 ± 3 mg extract/g PPF d.b., 55 °C, 4 MPa, 2.4 g/min) after dynamic extraction time of 17 min under optimized conditions. On the other hand, the carotenoid yield obtained using PLE (305 ± 18 μg α-carotene/g extract and 713 ± 46 μg β-carotene/g extract) was higher than the obtained by LPSE–SOX (142 ± 13 μg α-carotene/g extract and 317 ± 46 μg β-carotene/g extract). PLE technique showed the highest selectivity for carotenoids than LPSE techniques. The lowest cost of manufacturing (COM) were obtained for LPSE–PE and PLE with values of US$13.4 and US$29.2/kg extract for a 0.5 m³ vessel capacity.     

Extraction of phenolic compounds from pitanga (Eugenia uniflora L.) leaves by sequential extraction in fixed bed extractor using supercritical CO2, ethanol and water as solvents

With the goal of maximizing the extraction yield of phenolic compounds from pitanga leaves (Eugenia uniflora L.), a sequential extraction in fixed bed was carried out in three steps at 60 °C and 400 bar, using supercritical CO₂ (non-polar) as solvent in a first step, followed by ethanol (polarity: 5.2) and water (polarity: 9.0) in a second and third steps, respectively. All extracts were evaluated for global extraction yield, concentration and yield of both polyphenols and total flavonoids and antioxidant activity by DPPH method (in terms of EC₅₀). The nature of the solvent significantly influenced the process, since the extraction yield increased with solvent polarity. The aqueous extracts presented higher global extraction yield (22%), followed by ethanolic (16%) and supercritical extracts (5%). The study pointed out that the sequential extraction process is the most effective in terms of global extraction yield and yield of polyphenols and total flavonoids, because it produced the more concentrated extracts on phenolic compounds, since the supercritical ethanolic extract presented the highest phenolics content (240.5 mg GAE/g extract) and antioxidant capacity (EC₅₀ = 9.15 μg/mL). The most volatile fraction from the supercritical extract, which is similar to the essential oils obtained by steam distillation or hydrodistillation, presented as major compounds the germacrenos D and B + bicyclogermacrene (40.75%), selina-1,3,7(11)-trien-8-one + selina-1,3,7(11)-trien-8-one epoxide (27.7%) and trans-caryophyllene (14.18%).     

Optimization of supercritical CO2 extraction of different anatomical parts of lovage (Levisticum officinale Koch.) using response surface methodology and evaluation of extracts composition

Supercritical carbon dioxide extraction (SFE-CO₂) parameters were optimized using response surface methodology and central composite design for lovage (Levisticum officinale Koch.) roots and leaves containing valuable phytoconstituents. Mathematical model predicted the highest yields of extracts from roots and leaves 2.26 and 2.29%, respectively, at 45 MPa pressure, 60 °C temperature, 90 min (roots) and 30 min (leaves) extraction time, whereas the yield of hydrodistilled essential oil was 0.24 and 0.74%, respectively. The highest relative content of the most valuable constituent Z-ligustilide in roots and leaves extracts was 77 and 50% at 10 MPa; however, the highest yields of this compound from 100 g of dry material were obtained at the highest applied pressure and constituted 1188 mg (roots) and 540 mg (leaves). This study showed that lovage is a good source of Z-ligustilide and SFE-CO₂ is a preferable technique for its isolation.     

Processing and mechanical response of highly textured Al2O3

Dense, high quality textured alumina was fabricated by templated grain with only 0.14 wt% (SiO₂ + CaO) and 1–15 wt% tabular alumina templates From stereological measurements, texture fraction was 95% and unaffected by template loading or dopant concentration. Due to the excellent template alignment during casting, the full-width at half the maximum (FWHM) of the rocking curve was exceptionally low at 4.6°. Samples with the largest templated grains (1% templated alumina) have much lower strength (300–320 MPa) than those with smaller templated grains (400–500 MPa). Predominantly transgranular crack paths were observed in fracture surfaces both parallel and perpendicular to the oriented grains. The fracture toughness was anisotropic with slightly higher toughness perpendicular to the basal surface than parallel the direction grain basal surface. Surprisingly, the lowest density sample (93%) tested, which started with 15 wt% templates had the highest strength of 511 MPa ± 0.45 and highest fracture toughness of 4.58 ± 0.44 MPa m^1/2 when measured perpendicular to the basal surface of the grains.     

Extraction of low-molar-mass phenolics and lipophilic compounds from Pinus pinaster wood with compressed CO2

Near-supercritical and supercritical CO₂ was used to extract low-molar-mass phenolics and lipophilic compounds from Pinus pinaster wood. Extraction of samples containing sapwood and knotwood was carried out at 10⿿25 MPa and 30⿿50 °C to assess the influence of the operational conditions on the yields of total extracts and phenolics, as well as on the radical scavenging capacity of extracts. The use of ethanol as a co-solvent increased both the extraction yields and the concentration of phenolics in extracts. Operating under selected conditions (25 MPa, 50 °C, 10% ethanol), the extraction yield accounted for 4.1 wt% of the oven-dry wood. The extracts contained up to 7.6 g of phenolic compounds (measured as gallic acid equivalents) per 100 g extract, and showed one third of the radical scavenging capacity of Trolox. Native resin acids accounted for about 24 g per 100 g extracts, whereas flavonoids, lignans, stilbenes and juvabiones were found at lower proportions.     

Supercritical fluid extracts from tamarillo (Solanum betaceum Sendtn) epicarp and its application as protectors against lipid oxidation of cooked beef meat

The possibility of using the tamarillo (Solanum betaceum (Cav.) Sendtn (syn. Cyphomandra betacea)) epicarp as source of compounds with antioxidant activity in cooked beef meat (CBM) was explored. Extracts from tamarillo by supercritical fluid extraction (SFE) and Soxhlet extraction (SE) were obtained. The SFE was performed using pure CO₂ at different temperatures and pressures (40 and 50 °C; 10, 20 and 30 MPa) and CO₂ added with ethanol (CO₂/EtOH) as co-solvent (2, 5 and 8%, w/w). The SFE kinetics and mathematical modeling of the overall extraction curves (OEC) were also investigated. EtOH and hexane were used in the SE. The antioxidant activity (AA) of extracts was evaluated in CBM as well as the protection against lipid oxidation was determined by measuring lipid hydroperoxides (LHP) and thiobarbituric acid reactive species (TBARS). The extract obtained by SFE with CO₂/EtOH (50 °C/30 MPa and 2% of EtOH) showed the highest AA. In SFE, the co-solvent addition improved considerably the AA and the extraction yield. The extracts obtained by SFE with CO₂/EtOH showed a better AA compared with the synthetic antioxidant TBHQ. The highest yield values were achieved by SE with ethanol (7.7 ± 0.4%) and by SFE with 5% EtOH (1.9 ± 0.1%). The results indicate that extracts of tamarillo epicarp are a potential source of antioxidant compounds.     

Enrichment of Nigella damascena extract with volatile compounds using supercritical fluid extraction

β-Elemene, germacrene A and damascenine were extracted from lady-in-a-mist (Nigella damascena L.) seeds with supercritical carbon dioxide at 10–30 MPa and 40–60 °C. The influence of supercritical fluid extraction (SFE) conditions on the yield and concentration of volatiles in the extract and the extraction kinetics were studied. The extraction yields and the apparent solubility of volatile compounds increased with increasing density of CO₂. The highest total yield was obtained at 30 MPa and 40 °C but the selectivity for volatiles was low under these conditions. With respect to both yield of volatiles and their concentration in extract, the best results were at 12 MPa and 40 °C, either with one separator or with additional separator maintained at 5 MPa and 25 °C. The yields of β-elemene, germacrene A and damascenine reached 0.72, 3.31 and 3.65 mg g⁻¹ and their concentration in the extract was 2.62, 12.04 and 13.28 wt.%, respectively. Though the yields of germacrene A and damascenine were by about 20% higher using Soxhlet extraction with hexane than using SFE, their concentration in the extract where fatty oil prevailed was only 1.19 and 1.20 wt.%, respectively. Under the conditions of hydrodistillation, partial conversion of germacrene A to β-elemene occurred and its yield was higher than using the other methods but the composition of volatiles in the SFE extracts better corresponds to the original raw material.     

Design and optimization of a semi-continuous high pressure carbon dioxide extraction system for acetic acid

Supercritical fluid extraction with carbon dioxide was performed to extract acetic acid from real and model solutions of cow rumen fluid. Extractions were performed at varying temperature, pressure, solvent flow rate and extraction times for determining the extraction efficiency using a response surface statistical design. Within the range of variables studied, maximum acetic acid recovery of 93% was predicted at 2.0 g CO₂/min solvent flow rate, 2150 psi (14.8 MPa), 45 °C, and a 5 h extraction time using an initial acetic acid concentration of 92.4 g/L. A volumetric mass transfer coefficient of 2.848 h⁻¹ at 35 °C and 1500 psi (10.3 MPa) was calculated using a two-film linear driving force mass transfer model. The developed statistical model was tested for applicability on an acetic acid-spiked cow rumen fluid giving comparable results to the developed model. Results further showed that higher molecular weight volatile fatty acids such as propionic and butyric acid present in the fluid were preferentially removed before acetic acid extraction.     

Mechanical properties and microstructures of 2D Cf/ZrC–SiC composites using ZrC precursor and polycarbosilane

Two-dimensional C_f/ZrC–SiC composites were fabricated through mold-pressing and polymer infiltration and pyrolysis (PIP) using T700SC plain weave fiber fabrics as reinforcements with ZrC precursor and polycarbosilane. The mechanical properties and microstructures of the composites with 34, 45, and 56% fiber fraction were investigated. All composites showed a typical non-brittle fracture behavior and a large amount of pulled-out fibers were observed on the fracture surface. The bending strength and elastic modulus of the composite with 56 vol% fiber fraction increased up to 582 ± 80 MPa and 167 ± 25 GPa, with increasing fiber fraction. The mass loss and linear recession rate of the composites during the oxy-propane torch test were 0.008 g/s and ?0.003 mm/s, respectively. The formation of a ZrSiO₄ melt on the surface of the composite significantly contributed to the excellent ablative property of the 2D C_f/ZrC–SiC composites.     

Effect of the porous structure in carbon materials for CO2 capture at atmospheric and high-pressure

Activated carbons prepared from petroleum pitch and using KOH as activating agent exhibit an excellent behavior in CO₂ capture both at atmospheric (∼168 mg CO₂/g at 298 K) and high pressure (∼1500 mg CO₂/g at 298 K and 4.5 MPa). However, an exhaustive evaluation of the adsorption process shows that the optimum carbon structure, in terms of adsorption capacity, depends on the final application. Whereas narrow micropores (pores below 0.6 nm) govern the sorption behavior at 0.1 MPa, large micropores/small mesopores (pores below 2.0–3.0 nm) govern the sorption behavior at high pressure (4.5 MPa). Consequently, an optimum sorbent exhibiting a high working capacity for high pressure applications, e.g., pressure-swing adsorption units, will require a poorly-developed narrow microporous structure together with a highly-developed wide microporous and small mesoporous network. The appropriate design of the preparation conditions gives rise to carbon materials with an extremely high delivery capacity ∼1388 mg CO₂/g between 4.5 MPa and 0.1 MPa. Consequently, this study provides guidelines for the design of carbon materials with an improved ability to remove carbon dioxide from the environment at atmospheric and high pressure.     

Antioxidant properties of Achyranthis radix extract in rats

This study was performed to investigate the antioxidant activities of various fractions of Achyranthis radix extract using various solvents in vitro and antioxidant enzyme activities in vivo. Among the various fractions, when n-butanol was used as the extract solvent the DPPH radical scavenge rate was highest at 31.09 μg/ml. The thiobarbituric acid reaction value using n-butanol fraction was 0.33 at 532 nm after 6 days, representing a decrease of about 42% compared to control group. When the administered concentration of A. radix extract was 400 mg/kg/body weight/day, the xanthine oxidase activity in the liver was 19.5 mU/mg protein, representing a decrease of about 46% compared to the control group. The superoxide dismutase activity in the AR-E2 group was 89.4 Umol/(min mg protein), representing a decrease of about 40% compared to the control group. Catalase and glutathione peroxidase were decreased by about 24% and 58%, respectively, compared to the control group. When n-butanol fraction was used, the nitrite scavenging activity in various fractions at pH 1.2 was highest at 90.2%, an increase of about 90% compared to the control group. The results support the antioxidant potential of A. radix extract for various health supplements, pharmaceuticals, and mutraceuticals.