High pressure densities of carbon dioxide + dipentaerythritol hexaheptanoate: New experimental setup and volumetric behavior

To perform an appropriate selection of the lubricants in air conditioned systems working with carbon dioxide as refrigerant, the thermodynamic behavior of the CO₂ + lubricant systems must be well known. In this work we present a new setup to prepare compressed gas–liquid mixtures and to determine the high pressure density by using an automated densimeter HPM and two syringe pumps. To analyze the reliability of the procedure proposed, we have determined the densities and mixing volumes of four CO₂ + n-decane mixtures. We have found a good agreement with previous literature data. In addition new density values are reported for the binary system CO₂ + dipentaerythritol hexaheptanoate (DiPEC7) at several temperatures and pressures from 10 MPa to 120 MPa.     

Phase equilibria of (CO2 + H2O + NaCl) and (CO2 + H2O + KCl): Measurements and modeling

We report experimental measurements of the phase behavior of (CO₂ + H₂O + NaCl) and (CO₂ + H₂O + KCl) at temperatures from 323.15 K to 423.15 K, pressure up to 18.0 MPa, and molalities of 2.5 and 4.0 mol kg⁻¹. The present study was made using an analytical apparatus and is the first in which coexisting vapor- and liquid-phase composition data are provided. The new measurements are compared with the available literature data for the solubility of CO₂ in brines, many of which were measured with the synthetic method. Some literature data show large deviations from our results.The asymmetric (γ–φ) approach is used to model the phase behavior of the two systems, with the Peng–Robinson equation of state to describe the vapor phase, and the electrolyte NRTL solution model to describe the liquid phase. The model describes the mixtures in a way that preserves from our previous work on (CO₂ + H₂O) the values of the Henry's law constant and the partial molar volume of CO₂ at infinite dilution Hou et al. [22]. The activity coefficients of CO₂ in the aqueous phase are provided. Additionally, the correlation of Duan et al. [14] for the solubility of CO₂ in brines is tested against our liquid-phase data.     

Phase equilibria for the 2-ethoxyethyl acetate and 2-(2-ethoxyethoxy)ethyl acetate in supercritical CO2 at various temperatures and pressures up to 20 MPa

The (CO₂ + 2-ethoxyethyl acetate) and (CO₂ + 2-(2-ethoxyethoxy)ethyl acetate) systems at 313.2, 333.2, 353.2, 373.2 and 393.2 K as well as pressures up to 20.59 MPa have been investigated using variable-volume high pressure view cell by static-type. The solubility curve of 2-ethoxyethyl acetate and 2-(2-ethoxyethoxy)ethyl acetate in the (CO₂ + 2-ethoxyethyl acetate) and (CO₂ + 2-(2-ethoxyethoxy)ethyl acetate) systems increases as the temperature increases at a constant pressure. The (CO₂ + 2-ethoxyethyl acetate) and (CO₂ + 2-(2-ethoxyethoxy)ethyl acetate) systems exhibit type-I phase behavior. The experimental results for the (CO₂ + 2-ethoxyethyl acetate) and (CO₂ + 2-(2-ethoxyethoxy)ethyl acetate) systems correlate with the Peng–Robinson equation of state using a van der Waals one-fluid mixing rule including two adjustable parameters. The critical properties of 2-ethoxyethyl acetate and 2-(2-ethoxyethoxy)ethyl acetate are predicted with the Joback–Lyderson group contribution and Lee–Kesler method.     

Modelling of the inactivation kinetics of Escherichia coli,Saccharomyces cerevisiae and pectin methylesterase in orange juice treated with ultrasonic-assisted supercritical carbon dioxide

The combined effect of supercritical carbon dioxide (SC-CO₂) and high power ultrasound (HPU) on the inactivation kinetics of Escherichia coli, Saccharomyces cerevisiae and pectin-methyl esterase (PME) in orange juice was studied in order to select models that can predict their inactivation behaviour based on process parameters. Experiments were performed at different temperatures (31–41 °C, 225 bar) and pressures (100–350 bar, 36 °C). The inactivation rate of E. coli, S. cerevisiae and PME increased with pressure and temperature during SC-CO₂ + HPU treatments. The SC-CO₂ + HPU inactivation kinetics of E. coli, S. cerevisiae and PME were represented by models that included temperature, pressure and treatment time as variables, based on the Biphasic, the Peleg Type B, and the fractional models, respectively. The HPU-assisted SC-CO₂ batch system permits the use of mild process conditions and treatment times that can be even shorter than those of continuous SC-CO₂ systems.     

Evaluation of radish (Raphanus sativus L.) peroxidase activity after high-pressure treatment with carbon dioxide

The objective of this work was to assess the influence of compressed CO₂ on the specific activity of peroxidase (POD) from radish (Raphanus sativus L.). The protein concentrate, in phosphate buffer, was obtained through the precipitation of proteins with (NH₄)₂SO₄. The peroxidase activity was determined using guaiacol as substrate. A semi-factorial experimental design was adopted to evaluate the effects of temperature (30–50 °C), exposure time (1–6 h), carbon dioxide density (ρ_R = 0.6–1.8, resulting in pressures from 70.5 to 254.4 bar), and depressurization rate (10–200 kg/m³/min) on the peroxidase activity. Samples of lyophilized proteic concentrate were also submitted to high pressure and the effect of water content on the enzymatic activity in compressed CO₂ was studied. The water content in lyophilized samples was determined by thermo-gravimetric analysis. The results showed that the treatment of the enzymatic concentrate with CO₂ at high pressure could be a promising route to increase the POD activity.     

Mechanism of NO reduction by CO over Pt/SBA-15

The mechanism of the CO + NO reaction catalyzed by Pt/SBA-15 was studied via independent investigations of CO oxidation and NO disproportionation. Below 400 °C, both CO + O₂ and CO + NO reactions approach 100 % conversion, while the catalyst shows negligible activity for NO disproportionation. These results suggest that CO oxidation by atomic oxygen arising from NO dissociation is not a major route for CO₂ formation in the CO + NO reaction. In situ IR spectra reveal the formation of isocyanates (NCO⁻) adsorbed on silica. Their surface concentration changes with the extent of the CO + NO reaction. A mechanism is proposed in which isocyanates are reaction intermediates.     

Hydrothermal gasification of Rosa Damascena residues: Gaseous and aqueous yields

The gasification of Rosa Damascena residues – by-products of the rose-oil industry – was investigated under hydrothermal conditions at 500 °C and 600 °C, 35–45 MPa pressure with a reaction time of 1 h. The experiments were performed in the absence and presence of catalysts of K₂CO₃ and trona in a batch type reactor. The composition of the gaseous and aqueous products was determined by gas chromatography and high performance liquid chromatography, respectively. H₂, CO₂ and CH₄ are the main gaseous products while carboxylic acids (formic acid, acetic acid, glycolic acid) are the main components found in the aqueous phase followed by furfurals, phenols, aldehyde and ketones. More gaseous products were obtained at the higher temperature of 600 °C. Adding catalyst was found to aid the conversion process but the effect was only slight. Rosa Damascena residues have the potential to be a useful source for H₂ production in the future.     

Multi-walled carbon nanotubes stimulate callus induction,secondary metabolites biosynthesis and antioxidant capacity in medicinal plant Satureja khuzestanica grown in vitro

The present study was carried out to explore the potential effects of multi-walled carbon nanotubes (MWCNTs) on callus induction and secondary metabolism in Satureja khuzestanica. Leaf segments were aseptically cultured in B5 basal medium with different MWCNTs concentrations (0, 25, 50, 100, 250 and 500 μg ml⁻¹). The calli morphogenic responses were measured and the contents of phenolics, flavonoids, rosmarinic acid (RA), caffeic acid (CA), and the activity of polyphenol oxidase (PPO), l-phenylalanine ammonia-lyase (PAL) and peroxidase (POD) were quantified. Moreover, antioxidant activities of calli extract were assayed. Calli growth improved significantly with the increase of MWCNTs concentration, peaked at 50 μg ml⁻¹, and then followed a rapid decrease at 500 μg ml⁻¹. However, metabolic effects observed following exposure to MWCNTs particularly at 100 μg ml⁻¹ tended to be more pronounced than all other treatments, exhibiting significant induction of antioxidant activity with the lowest IC₅₀ value. Maximum oxidative stress index (H₂O₂) and the highest PPO and POD activities were observed on the media treated with 500 μg ml⁻¹ MWCNTs. Our findings suggest for the first time that use of MWCNTs at specific levels could act as a novel elicitor for in vitro biosynthesis of valuable secondary metabolites and antioxidant drugs.     

Near-infrared spectroscopic solubility measurement for thermodynamic analysis of melting point depressions of biphenyl and naphthalene under high-pressure CO2

Melting temperatures of organic solids are often depressed by high-pressure CO₂ due to a dissolution of CO₂ in the molten organic compounds. For thermodynamic analysis of the melting point depression, solubilities of CO₂ in molten biphenyl and naphthalene were measured by near-infrared spectroscopy at various temperatures and pressures up to 20 MPa. Molarity of the organic component was determined from the 3ν_CH absorption band, and that of CO₂ from the 2ν₁ + ν₃ band. Mole fraction of CO₂ in the liquid phase was found to be an increasing function of the pressure up to 0.6 at 20 MPa and a weakly decreasing function of the temperature. The solubility data were used for modeling of the mixtures by the Peng–Robinson equation of state with a binary interaction parameter k₁₂. Calculation of the solid–liquid–gas phase equilibrium for the model fluid qualitatively described a large decrease in the melting temperature with increasing pressure up to 10 MPa followed by a small change at higher pressures. The melting point change was interpreted by the two competing effects: hydrostatic pressure effect increases the melting point by ca. 8 °C at 20 MPa, whereas CO₂ solubility effect reduces it by ca. 30 °C. Decomposition of the solubility effect into ideal and non-ideal mixing parts revealed that the non-ideality increases the melting point by more than 10 °C.     

In situ FTIR micro-spectroscopy to investigate polymeric fibers under supercritical carbon dioxide: CO2 sorption and swelling measurements

An original experimental set-up combining a FTIR (Fourier Transformed InfraRed) microscope with a high pressure cell has been built in order to analyze in situ and simultaneously the CO₂ sorption and the polymer swelling of microscopic polymer samples, such as fibers, subjected to supercritical carbon dioxide. Thanks to this experimental set-up, we have determined as a function of the CO₂ pressure (from 2 to 15 MPa) the CO₂ sorption and the polymer swelling at T = 40 °C of four polymer samples, namely PEO (polyethylene oxide), PLLA (poly-l-lactide acid), PET (polyethylene terephtalate) and PP (polypropylene). The quantity of CO₂ sorbed in all the studied polymers increases with pressure. PEO and PLLA display a significant level of CO₂ sorption (20 and 25% respectively, at P = 15 MPa). However, we observe that a lower quantity of CO₂ can be sorbed into PP and PET (7 and 8% respectively, at P = 15 MPa). Comparing their thermodynamic behaviors and their intrinsic properties, we emphasize that a high CO₂ sorption can be reach if on one hand, the polymer is able to form specific interaction with CO₂ in order to thermodynamically favor the presence of CO₂ molecules inside the polymer and on the other, displays high chains mobility in the amorphous region. PLLA and PEO fulfilled these two requirements whereas only one property is fulfilled by PET (specific interaction with CO₂) and PP (high chains mobility). Finally, we have found that for a given CO₂ sorption, the resulting swelling of the polymer depends mainly on its crystallinity.     

Measurement of entrainer effects of water and ethanol on solubility of caffeine in supercritical carbon dioxide by FT-IR spectroscopy

The solubilities of caffeine in supercritical CO₂, supercritical CO₂ + water, supercritical CO₂ + ethanol, and supercritical CO₂ + water + ethanol were measured with a circulation-type apparatus combined with an on-line Fourier transform infrared (FT-IR) spectrometer at 313.2 K and 15.0 MPa. The solubilities of caffeine were determined with the peak absorbances of caffeine at 1190 cm⁻¹. The solubilities of caffeine increase until water is saturated in supercritical CO₂. The maximum increase rate is 22%. In CO₂ + caffeine + ethanol system, the solubilities of caffeine increase with increasing the concentration of ethanol. The solubility of caffeine becomes five times when 1000 mol m⁻³ of ethanol is added. In CO₂ + caffeine + water + ethanol system, the solubilities of caffeine are smaller than those with single entrainer of water or ethanol. The shape of the peaks of two CO stretching bands for caffeine were changed by the addition of ethanol. It was confirmed that the interaction species of caffeine interacting with ethanol are produced by deconvolution of the CO stretching bands. The enhancement of solubility for caffeine in supercritical CO₂ by the addition of ethanol is due to the hydrogen bonding between caffeine and ethanol.     

High pressure phase behavior of poly[isopropyl acrylate] and poly[isopropyl methacrylate] in supercritical fluid (SCF) solvent and SCF solvent + cosolvent mixtures

Cloud-point data are reported for poly(isopropyl acrylate) [P(IPA)] in CO₂, propane, propylene, butane, 1-butene, and dimethyl ether (DME) and for poly(isopropyl methacrylate) [P(IPMA)] in CO₂. P(IPA) + alkene cloud-point curves are ∼100 °C lower than the P(IPA) + alkane curves, which are close to the P(IPA) + CO₂ curve located at temperatures greater than 130 °C and pressures of 2500 bar. P(IPA) dissolves in pure DME at conditions as mild as 50 °C and 200 bar. Since IPA and IPMA monomers are used as cosolvents with CO₂, binary IPA + CO₂ and IPMA + CO₂ data are reported to complement the ternary cloud-point data. Both monomer + CO₂ mixtures exhibit type-I behavior and both are adequately modeled with the Peng–Robinson equation of state. IPMA is a more effective cosolvent than IPA. The polymer + CO₂ + monomer phase behavior suggests that it is viable to polymerize IPA or IPMA in CO₂ at moderate operating conditions.     

Ovicidal activities of supercritical CO2 and N2O on Ascaris suum eggs

This study examined whether supercritical CO₂ and N₂O fluids are effective in inactivating Ascaris suum eggs, which were chosen as a model for parasite eggs. The treatments were carried out in a multibatch apparatus, in which, the eggs could be placed atop a solid surface (non-immersed condition) or in aqueous solution (immersed condition). Various CO₂ and N₂O phases—including gas (6 MPa, 30 °C), liquid (8 MPa, 30 °C), subcritical (10 MPa, 30 °C), and supercritical (10 MPa, 37 °C)—were tested with exposure times ranging from 1 to 20 min. Supercritical CO₂ and N₂O both showed a similar, strong ovicidal effect, requiring only 1 min in non-immersed conditions and 5 min in water-immersed conditions to achieve a 2.4-log inactivation. Subcritical CO₂ and N₂O showed a weaker ovicidal effect. The effect was significantly reduced for the gas and liquid phases, compared with the supercritical phases. This study reports that supercritical CO₂ and N₂O can be effectively employed as a non-thermal treatment technique to control parasite egg contamination in fecal matter and food.     

Extraction of bioactive enriched fractions from Eruca sativa leaves by supercritical CO2 technology using different co-solvents

Supercritical fluid extraction from freeze-dried Eruca sativa leaves is assessed with the aim of studying the feasibility to obtain bioactive enriched fractions containing different classes of valuable compounds. Total extraction yields and compositions using pure CO₂ and CO₂ + selected co-solvents are compared. Overall extraction curves, fitted by the model of broken and intact cells developed by Sovová, are reported and the influence of the main parameters that affect the extraction process is analysed. The extract with the highest content in glucosinolates and phenols was collected at 30 MPa and 75 °C using 8% (w/w) of water with respect to the CO₂ flow rate, whereas the fraction richest in lipids was obtained using 8% (w/w) of ethanol as co-solvent at 45 °C and 30 MPa. A process including a first step with supercritical CO₂ extraction using water as co-solvent followed by a second step, where a fraction rich in lipids is extracted using ethanol as co-solvent, is proposed. SCCO₂ results are compared with Soxhlet and other methods that combine organic solvents with ultrasounds.     

Phase equilibria of the propylene glycol/CO2 and propylene glycol/ethanol/CO2 systems

The high-pressure vapour–liquid phase equilibria (P–T–x–y) of the binary mixture propylene glycol/CO₂ have been experimentally investigated at temperatures of (398.2, 423.2 and 453.2) K over the pressure range from (2.5 to 55.0) MPa using a static-analytic method. Furthermore, the high-pressure vapour–liquid phase equilibria (P–T–x–y) of the ternary mixture propylene glycol/CO₂/ethanol at constant temperatures of (398.2, 423.2 and 453.2) K and at constant pressure of 15.0 MPa have been determined using a static-analytic method. Initial concentrations of components in propylene glycol (PG)/ethanol (EtOH) mixture vary from 10 up to 90 wt.%. In general, for binary system it was observed that the solubility of CO₂ in the heavy propylene glycol reach phase increases with increasing pressure at constant temperature. On the contrary, the composition of gaseous phase is not influenced by the pressure or the temperature. On average the solubility of PG in light phase of CO₂ amounts to 30 wt.%. The system behaviour at temperature of 398.2 K was investigated up to 70.0 MPa and a single-phase region was not observed. Above the pressure 60.0 MPa a single-phase region of the system was observed for the temperature of 423.2 K. For the temperature of 453.2 K the single-phase was observed above the pressure of 48.0 MPa. For ternary system it was observed that the composition of heavy phase is slightly influenced by the temperature when the mass fraction of EtOH in initial mixture is higher than 50 wt.%. If the mass fraction of PG in initial mixture is higher than 50 wt.%, the composition of heavy phase is not influenced by the temperature anymore. The composition of the PG, EtOH and CO₂ in light phase remains more or less unchanged and it is not influenced by the conditions.     

Supercritical fluid extracts from tamarillo (Solanum betaceum Sendtn) epicarp and its application as protectors against lipid oxidation of cooked beef meat

The possibility of using the tamarillo (Solanum betaceum (Cav.) Sendtn (syn. Cyphomandra betacea)) epicarp as source of compounds with antioxidant activity in cooked beef meat (CBM) was explored. Extracts from tamarillo by supercritical fluid extraction (SFE) and Soxhlet extraction (SE) were obtained. The SFE was performed using pure CO₂ at different temperatures and pressures (40 and 50 °C; 10, 20 and 30 MPa) and CO₂ added with ethanol (CO₂/EtOH) as co-solvent (2, 5 and 8%, w/w). The SFE kinetics and mathematical modeling of the overall extraction curves (OEC) were also investigated. EtOH and hexane were used in the SE. The antioxidant activity (AA) of extracts was evaluated in CBM as well as the protection against lipid oxidation was determined by measuring lipid hydroperoxides (LHP) and thiobarbituric acid reactive species (TBARS). The extract obtained by SFE with CO₂/EtOH (50 °C/30 MPa and 2% of EtOH) showed the highest AA. In SFE, the co-solvent addition improved considerably the AA and the extraction yield. The extracts obtained by SFE with CO₂/EtOH showed a better AA compared with the synthetic antioxidant TBHQ. The highest yield values were achieved by SE with ethanol (7.7 ± 0.4%) and by SFE with 5% EtOH (1.9 ± 0.1%). The results indicate that extracts of tamarillo epicarp are a potential source of antioxidant compounds.     

High-pressure phase equilibria for the binary system carbon dioxide + dibenzofuran

The experimental solubility of dibenzofuran in near-critical and supercritical carbon dioxide and the solid–liquid–vapor (SLV) equilibrium line for the CO₂ + dibenzofuran system are reported. The built in-house static view cell apparatus used in these measurements is described. The solubility of naphthalene in supercritical CO₂ and the CO₂ + naphthalene SLV line are also determined in order to assess the reliability and accuracy of the measurement technique. The solubility of dibenzofuran in carbon dioxide is determined at 301.3, 309.0, 319.2, 328.7 and 338.2 K in the 6–30 MPa pressure range. Solubility data are correlated using the Chrastil model and the Peng–Robinson equation of state. This equation is also used to predict the CO₂ + dibenzofuran SLV line. Results show the feasibility of using supercritical CO₂ to extract dibenzofuran.     

Use of artificial neural networks for prediction of phase equilibria in the binary system containing carbon dioxide

Present work investigated the potential of artificial neural network (ANN) model to correlate the bubble and dew points pressures of binary systems containing carbon dioxide (CO₂) and hydrocarbon systems as functions of reduced temperature of non-CO₂ compounds, critical pressure, acentric factor of non-CO₂ compounds and CO₂ composition. In this regards, five binary systems at the temperature and pressure ranges of 263.15–393.15 K at 0.18–12.06 MPa were used to examine the feasibility of cascade-forward back-propagation ANN model. In this regard, the collected experimental data were divided in to two different subsets namely training and testing subsets. The training subset was selected in a way that covers all the ranges of the experimental data and operating conditions. Then, the accuracy of the proposed ANN model was evaluated through a test data set not used in the training stage. The optimal configuration of the proposed model was obtained based on the error analysis including minimum average absolute relative deviation percent (AARD %) and the appropriate (close to one) correlation coefficient (R²) of test data set. The obtained results show that the optimum neural network architecture was able to predict the phase envelope of binary system containing CO₂ with an acceptable level of accuracy of AARD % of 2.66 and R² of 0.9950 within their experimental uncertainty. In addition, comparisons were done between the Peng–Robinson (PR) equation of state (EOS) and ANN model for three different binary systems including CO₂ + 1-hexene, CO₂ + n-Hexane, and CO₂ + n-butane. Results show that developed optimal ANN model is more accurate compared to the PR EOS.     

Controllable synthesis of α-MoC1-x and β-Mo2C nanowires for highly selective CO2 reduction to CO

Transition metal carbides are attractive catalysts because of their similar properties to precious metals. Here, we report the controllable synthesis of α-MoC_1-x and β-Mo₂C nanowires as highly active and selective catalysts for CO₂ reduction to CO (CO₂ + H₂ → CO + H₂O, reverse water-gas shift reaction, RWGS). CO₂ conversion of > 60% together with nearly 100% CO selectivity was achieved at 600 °C, H₂:CO₂ molar ratio of 4:1, and space velocity of 36,000 mL g^− 1 h^− 1. A formate decomposition mechanism for the RWGS reaction was proposed based on the in-situ DRIFTS results.     

Phase behavior measurement for poly(isobornyl acrylate) + cosolvent systems in supercritical solvents at high pressure

We have conducted experiments to obtain cloud-point data of binary and ternary mixtures for poly(isobornyl acrylate) [P(IBnA)] (Mw = 100,000) + isobornyl acrylate(IBnA) in supercritical carbon dioxide (CO₂), P(IBnA) (Mw = 100,000) + dimethyl ether (DME) in CO₂, P(IBnA) (Mw = 100,000) in propane and butane, and P(IBnA) (Mw = 1,000,000) in propane, propylene, butane and 1-butene at high pressure conditions. Phase behaviors for these systems were measured at a temperature range from 323.4 K to 474.1 K and pressure up to 296.7 MPa. The cloud-point curves of P(IBnA) (Mw = 100,000) + IBnA and DME in CO₂ change from upper critical solution temperature (UCST) behavior to lower critical solution temperature (LCST) behavior as IBnA and DME concentration increases, and liquid–liquid–vapor phase behavior appears for the P(IBnA) (Mw = 100,000) + CO₂ + 80.3 wt.% IBnA system. Phase behaviors of P(IBnA) and 50 wt.% IBnA in CO₂ and P(IBnA) in propane and butane show the pressure difference in accordance with Mw = 1,000,000 and Mw = 100,000 of P(IBnA). Also, the solubility curves for IBnA in supercritical CO₂ were measured at a temperature range of (313.2–393.2) K and pressure up to 22.86 MPa. The experimental results were modeled with the Peng–Robinson equation of state (PR-EOS) using a mixing rule including two adjustable parameters. The critical property of IBnA is estimated with the Joback–Lyderson method.