Optimizing feedstock selection for biofuel production in Hawaii: CuO oxidative lignin products in C4 grasses

Global interest in renewable fuels is rapidly growing with particular emphasis on local energy growth and creating new energy feedstocks, specifically liquid fuel sources. However, the interactive effect of plant species/variety and growth environment on plant structural components, which may influence conversion efficiency and thus play an important role in optimizing the production of biofuels, is not fully understood. In this study cupric oxide (CuO) extractable lignin, which extracts and quantifies lignin-derived monomers, was determined for 25 cultivated and naturalized tropical perennial C₄ grass varieties of napiergrass and Guinea grass that were under assessment for suitability as feedstocks for liquid fuel generation. Principal component analysis of CuO extractable lignin-derived monomers showed differences in composition between napiergrass and Guinea grass, as well as environmental differences within many, but not all napiergrass varieties. Among the samples tested, the greatest differences in lignin composition occurred specifically in vanillyl lignin structures. A wide range (1–2.5) in the ratio of cinnamyl to vanillyl structures (C/V), which often relates to enzymatic degradability in natural systems, was also found. It is expected that the observed CuO lignin differences representing the structure and bonding of lignin will relate to ease of chemical and enzymatic conversion and the effectiveness of pretreatment and conversion in biofuel application. We hypothesize that the C/V ratio of feedstock will positively relate to conversion efficiency and if supported, then compositional lignin metrics such as the C/V ratio could be a predictor to select for more easily degradable biomass for biofuel production.     

Anaerobic digestion of corn silage on a commercial scale: Differential utilization of its chemical constituents and characterization of the solid digestate

The utilization of different chemical constituents of corn silage during industrial-scale anaerobic digestion was determined. Corn silage together with the resulting solid digestate generated during biogas production were collected from an industrial plant during a regular operating period. Moisture, water and ethanol extractives, ash, total nitrogen, starch, cellulose, the monomeric composition of hemicellulose, acid soluble and acid insoluble lignin were measured in both corn silage and corn silage solid digestate. The relative consumption of each component of corn silage during its anaerobic digestion was estimated with reference to acid insoluble lignin. It was assumed that lignin was not digested throughout the process. Starch and large fractions of extractives and acid soluble lignin were digested. In contrast, the digestion of cellulose and particularly hemicellulose were limited (40% and 29% respectively). Of the hemicellulose monomers, xylose was the least digested (20%). The present work shows that the digestate produced by commercial corn-silage anaerobic digestion contains a notable quantity of cell wall polymers. These could potentially be used in biorefinery processes, e.g. ethanol and xylo-oligosaccharide production.     

Sweet sorghum as a whole-crop feedstock for ethanol production

The potential of sweet sorghum as an alternative crop for ethanol production was investigated in this study. Initially, the enzymatic hydrolysis of sorghum grains was optimized, and the hydrolysate produced under optimal conditions was used for ethanol production with an industrial strain of Saccharomyces cerevisiae, resulting in an ethanol concentration of 87 g L⁻¹. From the sugary fraction (sweet sorghum juice), 72 g L⁻¹ ethanol was produced. The sweet sorghum bagasse was submitted to acid pretreatment for hemicellulose removal and hydrolysis, and a flocculant strain of Scheffersomyces stipitis was used to evaluate the fermentability of the hemicellulosic hydrolysate. This process yielded an ethanol concentration of 30 g L⁻¹ at 23 h of fermentation. After acid pretreatment, the remaining solid underwent an alkaline extraction for lignin removal. This partially delignified material, known as partially delignified lignin (PDC), was enriched with nutrients in a solid/liquid ratio of 1 g/3.33 mL and subjected to simultaneous saccharification and fermentation (SSF) process, resulting in an ethanol concentration of 85 g L⁻¹ at 21 h of fermentation. Thus, from the conversion of starchy, sugary and lignocellulosic fractions approximately 160 L ethanol.ton⁻¹ sweet sorghum was obtained. This amount corresponds to 13,600 L ethanol.ha⁻¹.     

Upgraded biofuel from residue biomass by Thermo-Catalytic Reforming and hydrodeoxygenation

Research is focused on the utilisation of waste or residue biomass for bioenergy conversion. A promising conversion technology for the production of liquid biofuels from residue biomass is a process called Thermo-Catalytic Reforming (TCR^®​) which is a combination of prior thermal treatment of the biomass at mild temperatures (intermediate pyrolysis) followed by a second catalytic treatment step at elevated temperatures (reforming). This article focuses on the conversion of TCR^® liquids from digestate as a feedstock for subsequent hydrocarbon production. The generated bio-oil showed a lower heating value of 34.0 MJ kg⁻¹ with an oxygen content of 7.0% and a water content of 2.2%. The bio-oil was hydrodeoxygenated using an industrial NiMo–Al₂O₃ catalyst at temperatures of 503 K–643 K and a pressure of 14 MPa. The hydrodeoxygenated bio-oil reached a lower heating value of 42.3 MJ kg⁻¹ with an oxygen content below 0.8 mg kg⁻¹ and water content of 30 ppm. Product yields and catalyst life give confidence that upgrading of the TCR^®​ bio-oil offers a suitable option to meet the high standards of common fuels.     

Sunflower as a biofuels crop: An analysis of lignocellulosic chemical properties

Four accessions of cultivated sunflower (Helianthus annuus) and silverleaf sunflower (Helianthus argophyllus), were each grown in three locations (Georgia, British Columbia, and Iowa) at different planting densities and phenotyped for biomass-related traits and wood biochemistry. In most environments, H. argophyllus produced significantly more biomass than H. annuus. Cell wall chemistry for a subset of plants grown in Georgia and Iowa was assessed using analytical wet chemistry methods to measure lignin and sugar content/composition. The analysis of lignin and the S/G-lignin ratios for a larger number of samples (n > 250) was also assessed by high-throughput pyrolysis Molecular Beam Mass Spectrometry. Average pyMBMS estimated lignin content (i.e., dry weight fraction) for 60 °C dried basal stem samples of H. annuus and H. argophyllus was 29.6% (range, 24.0%–34.6%) and 28.6% (range, 24.6%–33.3%), respectively when averaged across all environments. The average S/G lignin mass ratio was 1.5 (range, 1.0–2.0) for H. annuus and 1.7 (range, 1.0–2.4) in H. argophyllus. Stem samples from these two species only differed statistically for a few cell wall chemistry traits; however, accession level differences within each species were apparent. Cell wall chemistry in both species was significantly affected by both location and planting density, thus demonstrating the need to select for these traits in the environment for which the crop will be produced. Overall, these results show that cultivated sunflower and silverleaf sunflower both possess the necessary phenotypic diversity to facilitate the development of a hybrid sunflower with improved lignocellulosic biofuels traits, namely increased biomass, decreased lignin, and increased glucan.     

Combined ethanol and methane production from switchgrass (Panicum virgatum L.) impregnated with lime prior to steam explosion

Pretreatments are crucial to achieve efficient conversion of lignocellulosic biomass to soluble sugars. In this light, switchgrass was subjected to 13 pretreatments including steam explosion alone (195 °C for 5, 10 and 15 min) and after impregnation with the following catalysts: Ca(OH)₂ at low (0.4%) and high (0.7%) concentration; Ca(OH)₂ at high concentration and higher temperature (205 °C for 5, 10 and 15 min); H₂SO₄ (0.2% at 195 °C for 10 min) as reference acid catalyst before steam explosion. Enzymatic hydrolysis was carried out to assess pretreatment efficiency in both solid and liquid fraction. Thereafter, in selected pretreatments the solid fraction was subjected to simultaneous saccharification and fermentation (SSF), while the liquid fraction underwent anaerobic digestion (AD). Lignin removal was lowest (12%) and highest (35%) with steam alone and 0.7% lime, respectively. In general, higher cellulose degradation and lower hemicellulose hydrolysis were observed in this study compared to others, depending on lower biomass hydration during steam explosion. Mild lime addition (0.4% at 195 °C) enhanced ethanol in SSF (+28% than steam alone), while H₂SO₄ boosted methane in AD (+110%). However, methane represented a lesser component in combined energy yield (ethanol, methane and energy content of residual solid). Mild lime addition was also shown less aggressive and secured more residual solid after SSF, resulting in higher energy yield per unit raw biomass. Decreased water consumption, avoidance of toxic compounds in downstream effluents, and post process recovery of Ca(OH)₂ as CaCO₃ represent further advantages of pretreatments involving mild lime addition before steam explosion.     

A new future for carbohydrate fuel cells

The development of renewable energy sources to reduce our dependence on limiting fossil fuel reserves continues to be a critical research initiative. Utilizing the abundant high energy content of carbohydrates contained in biomass (cellulose and hemicellulose) must be considered to be an important contribution to our overall energy budget. Carbohydrate-derived furan-based liquid fuels and especially ethanol are becoming important added components forming gasoline blends to lower overall fossil fuel use. Alternate renewable energy processes that more efficiently use the carbohydrate energy content are desirable and would lower the overall carbohydrate input requirement for energy production. Recently, new catalysts have shown the feasibility of efficiently transporting the 24 electrons in glucose to fuel cell electrodes making possible the direct conversion of the stored energy in carbohydrates into electricity with the benign formation of carbonate and water as products. The conversion of glycerol, a byproduct of biodiesel production, into three-carbon carbohydrates provides another opportunity to produce electricity from an abundant carbohydrate source. New developments in catalyst systems promise to make carbohydrate fuel cells an important part of future energy strategies.     

Compositional differences among upland and lowland switchgrass ecotypes grown as a bioenergy feedstock crop

Feedstock quality mainly depends upon the biomass composition and bioenergy conversion system being used. Higher cellulose and hemicellulose concentrations are desirable for biochemical conversion, whereas higher lignin is favored for thermochemical conversion. The efficiency of these conversion systems is influenced by the presence of high nitrogen and ash concentrations. Switchgrass (Panicum virgatum L.) varieties are classified into two ecotypes based on their habitat preferences, i.e., upland and lowland. The objectives of this study were to quantify the chemical composition of switchgrass varieties as influenced by harvest management, and to determine if ecotypic differences exist among them. A field study was conducted near Ames, IA during 2012 and 2013. Upland (‘Cave-in-Rock’, ‘Trailblazer’ and ‘Blackwell’) and lowland switchgrass varieties (‘Kanlow’ and ‘Alamo’) were grown in a randomized block design with six replications. Six biomass harvests were collected at approximately 2-week intervals each year. In both years, delaying harvest increased cellulose, hemicellulose and lignin concentrations while decreasing nitrogen and ash concentrations in all varieties. On average, Kanlow had the highest cellulose and hemicellulose concentration (354 and 321 g kg⁻¹ DM respectively), and Cave-in-Rock had the highest lignin concentration (33 g kg⁻¹ DM). The lowest nitrogen and ash concentrations were observed in Kanlow (14 and 95 g kg⁻¹ DM respectively). In general, our results indicate that delaying harvest until fall improves feedstock quality, and ecotypic differences do exist between varieties for important feedstock quality traits. These findings also demonstrate potential for developing improved switchgrass cultivars as bioenergy feedstock by intermating lowland and upland ecotypes.     

Evaluation of dilute acid and alkaline pretreatments,enzymatic hydrolysis and fermentation of napiergrass for fuel ethanol production

Napiergrass (Pennisetum purpureum Schum.) is a promising low cost raw material which does not compete with food prices, has attractive yields and an environmentally friendly farming. Dilute sulfuric acid pretreatment of napiergrass was effective to obtain high yields of sugars and low level of degradation by-products from hemicellulose. Detoxification with Ca(OH)₂ removed inhibitors but showed sugars loss. An ethanol concentration of 21 g/L after 176 h was found from the hydrolyzate using Pichia stipitis NBRC 10063 (fermentation efficiency 66%). An additional alkaline pretreatment applied to the solid fraction remaining from the diluted acid pretreatment improved the lignin removal. The highest cellulose hydrolysis values were found with the addition of β-glucosidase and PEG 6000. The simultaneous hydrolysis and fermentation of the cellulosic fraction with Saccharomyces cerevisiae, 10% (w/v) solid concentration, β-glucosidase and PEG 6000, showed the highest ethanol concentration (24 g/L), and cellulose hydrolysis values (81%). 162 L ethanol/t of dry napiergrass were produced (overall efficiency of 52%): 128 L/t from the cellulosic fraction and 34 L/t from the hemicellulosic fraction.     

GIS-based assessment of sustainable crop residue potentials in European regions

In this paper a novel model based on a geographic information system (GIS) is presented for the assessment of sustainable crop residue potentials. The approach is applied to analyse the amount and the spatial distribution (1 km × 1 km grid cells) of cereal straw, root crop and oil plant residues for five European regions, considering spatially differentiated environmental sustainability issues, i.e. organic carbon content in topsoil, soil erodibility, and protected areas. The maximum sustainable residue potential varies strongly between the regions and residue types. In the scenarios Basis and Restrict, it accounts for 45–59% and 24–48% of the theoretical potential respectively without considering competing uses. Among the crop residues, cereal straw shows the highest energy potential in all regions under investigation. In terms of wet mass it accounts for 3.7 Mio. t_wet/a in North Rhine-Westphalia, 1.6 Mio. t_wet/a in Île-the-France, 1.2 Mio. t_wet/a in Wallonia, 0.9 Mio. t_wet/a in West Midlands, and 0.3 Mio. t_wet/a in South Netherlands (scenario Basis). Our survey shows that spatially differentiated potential estimations and the inclusion of crop residues other than cereal straw are urgently needed to improve the present rough estimations for crop residues which can be used in a sustainable way. The rather high spatial resolution of our analyses particularly allows for the support of regional stakeholders and prospective investors when it comes to questions of regional availability of biomass resources, transport distances to biomass conversion plants, and identification of suitable plant sites and sizes, respectively.     

Improved methods for the determination of drying conditions and fraction insoluble solids (FIS) in biomass pretreatment slurry

Accurate and precise chemical characterization of biomass feedstocks and process intermediates is a requirement for successful technical and economic evaluation of biofuel conversion technologies. The uncertainty in primary measurements of the fraction insoluble solid (FIS) content of dilute acid pretreated corn stover slurry is the major contributor to uncertainty in yield calculations for enzymatic hydrolysis of cellulose to glucose. This uncertainty is propagated through process models and impacts modeled fuel costs. The challenge in measuring FIS is obtaining an accurate measurement of insoluble matter in the pretreated materials, while appropriately accounting for all biomass derived components. Three methods were tested to improve this measurement. One used physical separation of liquid and solid phases, and two utilized direct determination of dry matter content in two fractions. We offer a comparison of drying methods. Our results show utilizing a microwave dryer to directly determine dry matter content is the optimal method for determining FIS, based on the low time requirements and the method optimization done using model slurries.     

Biosynthesis of β-caryophyllene,a novel terpene-based high-density biofuel precursor,using engineered Escherichia coli

β-caryophyllene is a common sesquiterpene compound currently being studied as a promising precursor for the production of high-density fuels. Acute demand for high-density fuels has provided the impetus to pursue biosynthetic methods to produce β-caryophyllene from reproducible sources. In this study, we produced β-caryophyllene by assembling a biosynthetic pathway in an engineered Escherichia coli strain of which phosphoglucose isomerase gene has been deleted. The 1- deoxy-d-xylulose 5-phosphate (DXP) or heterologous mevalonate (MVA) pathways were employed. Meanwhile, geranyl diphosphate synthase, glucose-6-phosphate dehydrogenase and β-caryophyllene synthase genes were co-overexpressed in the above strain. The final genetically modified strain, YJM59, produced 220 ± 6 mg/L of β-caryophyllene in flask culture. We also evaluated the use of fed-batch fermentation for the production of β-caryophyllene. After induction for 60 h, the YJM59 strain produced β-caryophyllene at a concentration of 1520 mg/L. The volumetric production fermented in the aerobic fed-batch was 0.34 mg/(L·h·OD₆₀₀) and the conversion efficiency of glucose to β-caryophyllene (gram to gram) was 1.69%. Our results are the first successful attempt to produce β-caryophyllene using E. coli BL21(DE3), and provide a new strategy that is green and sustainable for the production of β-caryophyllene.     

In vitro-propagated Miscanthus × giganteus plants can be a source of diversity in terms of their chemical composition

Miscanthus × giganteus is a triploid hybrid propagated vegetatively from rhizomes or in a tissue culture, so its clones are characterised by a very low genetic diversity. Giant Miscanthus is cultivated mainly for biomass used as biofuel; depending on its chemical composition, it can be used in many industries. The goal of this work was to determine whether regenerants obtained in tissue culture can be a source of new forms characterised by different biomass yield and energy values as well as by their concentration of cellulose, hemicellulose and lignin. In the study the number and height of stems as well as the dry weight, ash and water mass fraction of biomass were estimated. The study was performed on Miscanthus plants propagated from rhizomes obtained from two different locations in Poland (Zabierzów – Z and Radzików – R), and on regenerants (Iv) obtained from Z plants. The results indicated that somaclonal variation occurs in M. × giganteus cultures and that regenerants show low polymorphic variation compared to donor plants. Plants propagated in an in vitro culture showed the lowest stem height, but the highest number of stems per plant. Dry matter yield was greatest in the R group, while regenerants demonstrated the highest level of hemicellulose fraction and lowest cellulose and lignin concentration. Energy value was the highest for Z plants, but Iv plants showed energy values on the same level as those of R plants. The data suggest that in vitro-propagated plants may be a source of new Miscanthus forms.     

Enhanced substrate degradation and methane yield with maleic acid pre-treatments in biomass crops and residues

Organic acids are envisaged as alternative catalysts to strong mineral acids, in pre-treatment of ligno-cellulosic biomass for anaerobic digestion (AD). To evaluate this hypothesis, an untreated control and four pre-treatments (25 °C for 24 h) involving two levels of maleic acid (34.8 and 69.6 kg m⁻³), alone and combined with sulphuric acid (4 kg m⁻³), were studied in three agricultural substrates: Arundo (aka giant reed), Barley straw and B133 fibre sorghum. Methane production was assessed in a batch AD assay (35 °C for 51 days) with 4 g L⁻¹ of volatile solid (VS) load. Fibre composition and structure were investigated through chemical analysis and Fourier transform infrared (FTIR) spectrometry. Arundo and B133 that were the most and least recalcitrant substrate, respectively, staged the highest and lowest increase in methane with high maleic acid: +62% over 218 cm³ g⁻¹ of VS in untreated Arundo; +36% over 284 cm³ g⁻¹ of VS in untreated B133. Barley straw showed an intermediate behaviour (+41% over 269 cm³ g⁻¹ of VS). H₂SO₄ addition to maleic acid did not improve CH₄ output. The large increase in methane yield determined by pre-treatments was reflected in the concurrent decrease of fibre (between 14 and 39% depending on fibrous component). Based on FTIR spectra, bands assigned to hemicellulose and cellulose displayed lower absorbance after pre-treatment, supporting the hypothesis of solubilisation of structural carbohydrates and change in fibre structure. Hence, maleic acid was shown a suitable catalyst to improve biodegradability of ligno-cellulosic biomass, especially in recalcitrant substrates as Arundo.     

Ash reduction strategies in corn stover facilitated by anatomical and size fractionation

There is growing interest internationally to produce fuels from renewable biomass resources. Inorganic components of biomass feedstocks, referred to collectively as ash, damage equipment and decrease yields in thermal conversion processes, and decrease feedstock value for biochemical conversion processes. Decreasing the ash content of feedstocks improves conversion efficiency and lowers process costs. Because physiological ash is unevenly distributed in the plant, mechanical processes can be used to separate fractions of the plant based on ash content. This study focuses on the ash separation that can be achieved by separating corn stover by particle size and anatomical fraction. Baled corn stover was hand-separated into anatomical fractions, ground to <19.1 mm, and size separated using six sieves ranging from 9.5 to 0.150 mm. Size fractions were analyzed for total ash content and ash composition. Particle size distributions observed for the anatomical fractions varied considerably. Cob particles were primarily 2.0 mm or greater, while most of the sheath and husk particles were 2.0 mm and smaller. Particles of leaves greater than 0.6 mm contained the greatest amount of total ash, ranging from approximately 8 to 13% dry weight of the total original material, while the fractions with particles smaller than 0.6 mm contained less than 2% of the total ash of the original material. Based on the overall ash content and the elemental ash, specific anatomical and size fractions can be separated to optimize the feedstocks being delivered to biofuels conversion processes and minimize the need for more expensive ash reduction treatments.     

Improving methane production from wheat straw by digestate liquor recirculation in continuous stirred tank processes

Wheat straw is an abundant, cheap substrate that can be used for methane production. However, the nutrient content in straw is inadequate for methane fermentation. In this study, recycling digestate liquor was implemented in single-stage continuous stirred tank processes for enrichment of the nutrient content of straw with the aim of improving the methane production. The VS-based organic loading rate was set at 2 g/(L d) and the solid retention time at 40 days. When wheat straw alone was used as the substrate, the methane yields achieved with digestate liquor recycling was on average 240 ml CH₄/g VS giving a 21% improvement over the processes without recycling. However, over time, the processes suffered from declining methane yields and poor stability evidenced by low pH. To maintain process stability, wheat straw was co-digested with sewage sludge or supplemented with macronutrients (nitrogen and phosphorous). As a result, the processes with digestate liquor recycling could be operated stably, achieving methane yields ranging from 288 to 296 ml CH₄/g VS. Besides, the processes could not be operated sturdily with supplementation of macronutrients without digestate liquor recycling. The highest methane yield (296 ± 16 ml CH₄/g VS) was achieved by co-digestion with sewage sludge plus recycling of digestate liquor after filtration (retention of nutrients and microorganisms). This was comparable to the maximum expected methane yield of 293 ± 13 ml CH₄/g VS achieved in batch test. The present study therefore demonstrated that digestate liquor recycling could lead to a decreased dilution of vital nutrients from the reactors thereby rendering high process performance and stability.     

Environmental assessment of electricity generation from an Italian anaerobic digestion plant

A standard ISO Life Cycle Assessment study was carried out to evaluate the environmental sustainability of electricity production from an anaerobic digestion (AD) plant using a mixture of dedicated energy crops, agricultural residues and livestock effluents as input materials. The functional unit was 1 MJ of electricity. System boundaries were from cradle to grave and covered all the phases from energy crops cultivation to the production of biogas and its use in a Combined Heat and Power plant to produce electricity. Liquid and solid digestate storage and spreading on agricultural land were included. Primary data were collected from the AD plant for all the above phases. Since heat produced is used only internally, no allocation was applied in the study. As regards digestate management, CH₄ emissions were calculated from literature, whereas four literature methods were applied for calculation of nitrogen emissions with the goal to perform a sensitivity analysis on LCA results. ILCD Handbook impact assessment methodologies were used. Results show that the main hotspots are energy crops cultivation and the management of digestate, mainly because of both nitrogen and methane emissions, affecting Global Warming, Acidification, Marine and Freshwater Eutrophication. Finally, a detailed Monte Carlo analysis, was carried out to evaluate the results uncertainty. The study represents the state of the art about the environmental performance of the AD plant with the use of sensitivity and uncertainty analysis, which both improve the reliability of results, and allows drawing general conclusions on how to mitigate the environmental impacts of AD process.     

Periodic peristalsis enhancing the high solids enzymatic hydrolysis performance of steam exploded corn stover biomass

Enzymatic hydrolysis beyond 15% solid loading offers many advantages such as increased sugar and ethanol concentrations and decreased capital cost. However, difficult mixing and handling limited its industrialized application. A novel intensification method, periodic peristalsis, had been exploited to improve the high solids enzymatic hydrolysis performance of steam exploded corn stover (SECS). The optimal steam explosion conditions were 200 °C and 8 min, under which glucan and xylan recovery was 94.3% and 64.8%, respectively. Glucan and xylan conversions in periodic peristalsis enzymatic hydrolysis (PPEH) were 28.0–38.5% and 25.0–36.0% higher than those in static state enzymatic hydrolysis with solid loading increasing from 1% to 30%, respectively, while they were 1.0–11.2% and 3.0–9.2% higher than those in incubator shaker enzymatic hydrolysis (ISEH). Glucan and xylan conversion in PPEH at 21% solid loading reached 71.2% and 70.3%, respectively. Periodic peristalsis also facilitated fed-batch enzymatic hydrolysis of which SECS was added completely before transition point. Results presented that PPEH shortened the transition point time from solid state to slurry state, decreased the viscosity of hydrolysis mixture, and reduced the denaturation effect of enzymes compared with ISEH, and hence improve the high solids enzymatic hydrolysis efficiency.     

What is the potential for biogas digesters to improve soil carbon sequestration in Sub-Saharan Africa? Comparison with other uses of organic residues

Using bioslurry from anaerobic digestion as an organic fertilizer has great potential to increase carbon sequestration by supplying organic matter to the soil. This paper examines this potential in Sub-Saharan Africa compared to other uses of organic residues, including burning on pyrolysis cook-stoves and composting. Measurements of loss of carbon on treatment of organic residues indicate that the proportion of carbon lost from organic residue during treatment is greater for anaerobic digestion than for aerobic composting or pyrolysis. The stability of organic residue is increased by treatment, and is similar for composted and anaerobically digested material, but is higher for material treated by pyrolysis. Simulations using the RothC model, driven by parameters based on incubations of the organic residues with soil, suggest that on the basis of decomposability alone, treated organic residues sequester significantly more carbon than untreated organic residues, and despite the differences observed in stability, unless biochar contains a high proportion of inert organic material that does not decompose at all, the potential carbon sequestration by incorporating biochar is similar to that for compost or bioslurry. However, if losses of carbon during treatment are also taken into account, incorporating bioslurry sequesters only approximately the same amount of carbon as if the organic residue had been left untreated. By contrast, incorporating compost and biochar sequesters significantly more carbon than incorporating the untreated organic residue. Therefore using bioslurry as an organic fertilizer sequesters less of the carbon in the soil from organic residue than burning on pyrolysis cook-stoves or composting.     

Ethanologens vs. acetogens: Environmental impacts of two ethanol fermentation pathways

Bioconversion production of ethanol from cellulosic feedstock is generally proposed to use direct fermentation of sugars to ethanol. Another potential route for ethanol production is fermentation of sugars to acetic acid followed by hydrogenation to convert the acetic acid into ethanol. The advantage of the acetogen pathway is an increased ethanol yield; however, using an acetogen requires the additional hydrogenation, which could substantially affect the life cycle global warming potential of the process. Assuming a poplar feedstock, a cradle to grave Life cycle assessment (LCA) is used to evaluate the environmental impacts of an acetogen based fermentation pathway. An LCA of a fermentation pathway that uses ethanologen fermentation is developed for comparison. It is found that the ethanologen and acetogen pathways have Global Warming Potentials (GWP) that are 92% and 46% lower than the GWP of gasoline, respectively. When the absolute GWP reduction compared to gasoline is calculated using a unit of land basis, the benefit of the higher ethanol yield using the acetogen is observed as the two pathways achieve similar GWP savings. The higher ethanol yield in the acetogen process plays a crucial role in choosing a lignocellulosic ethanol production method if land is a limited resource.