Thermochemical liquefaction characteristics of Cyanobacteria in subcritical and supercritical ethanol–water mixture

The thermochemical liquefaction of Cyanobacteria in subcritical and supercritical ethanol–water mixture was studied with different reaction temperature, reaction time, solvent composition, and solid–liquid ratio. Highest bio‐oil yield of 42.5% containing mainly fatty acid ethyl esters, phenols, pyrrolidinones, and pyridinols was obtained in ethanol–water mixture (4/6, v/v) at temperature of 320°C for 30 min, with solid–liquid ratio of 1 g/15 mL. Both solvent composition and supercritical state had great influence on the liquefaction of Cyanobacteria, while the synergetic effects of water and ethanol in co‐solvents were again verified. Copyright © 2017 John Wiley & Sons, Ltd.     

Optimization of process parameters and catalytic pyrolysis of Cascabela thevetia seeds over low-cost catalysts towards renewable fuel production

The present study deals with the optimization of process parameters and thermocatalytic pyrolysis of Cascabela thevetia (CT) seeds in a semi-batch cylindrical-shaped reactor. Response surface methodology (RSM) was employed for the optimization of process variables, while commercial catalysts CaO and Al₂O₃ were used for catalytic pyrolysis. From results, it was concluded that 525 °C temperature, 75 °C min⁻¹ heating rate, and 75 mL min⁻¹ flow of nitrogen yielded maximum pyrolytic liquid (45.26 wt%) while with the attendance of catalysts at 20 wt% increased the yield of pyrolytic liquid (49.12 wt% and 46.87 wt% for CaO and Al₂O₃ respectively). Optimization outcomes displayed that linear and quadratic terms of utilized factors were more noteworthy while interaction effects between the factors were not significant. Further, characterization of pyrolytic oil established that utilization of catalysts expressively enhanced its properties by reducing viscosity and boosted the calorific value. FTIR examination of pyrolytic oil showed that the attendance of phenols, ethers, alcohols, ketones, alkanes, acids, etc., while ¹H NMR results supported the FTIR results. GC-MS analysis showed a substantial reduction of phenols and oxygen-rich products and boost the development of alcohol and aldehydes in pyrolytic oil with the introduction of catalysts. These parameters indicate improved properties of pyrolytic oil, which intensified its bioenergy capabilities.     

Effect of preparation method on the performance of Ni/MgOSiO2 catalysts for glycerol steam reforming

Catalysts were prepared with 10 wt% of Ni(II) and 30 wt% of MgO over commercial SiO₂, using dry (physical mixture) and wet (impregnation with different polarities solvents: ethanol and acetone) sequential processes. The characterization techniques used were energy dispersive X-ray spectroscopy, nitrogen physisorption, X-ray diffractometry, H₂ temperature-programmed reduction, X-ray diffractometry in situ with H₂, H₂ temperature-programmed desorption, and scanning electron microscopy. In order to verify activity, selectivity, and carbon deposition, the catalysts were tested in glycerol steam reforming reaction at 600 °C, for 5 h, at a 12:1 water:glycerol molar ratio. After the reactions, the catalysts were submitted to thermogravimetric analysis, X-ray diffractometry, and scanning electron microscopy, in order to characterize the carbon deposits during the catalytic process. Impregnation solvent polarity influenced the metallic dispersion and the metallic area of the catalysts, given that, the lower the polarity of the solvent, the higher the metallic dispersion and the area, and the lesser the carbon deposition during the reaction. The material that presented the best catalytic performance in terms of H₂ output and carbon deposition was the catalyst prepared with ethanol as impregnation solvent (less polar solvent), as a consequence of its greater dispersion and larger metallic area.     

Influence of moisture content on the direct gasification of dewatered sludge via supercritical water

In the present study, the feasibility of the direct gasification of dewatered sludge in supercritical water and the effect of water content on supercritical water gasification of the dewatered sludge were investigated using a high-pressure autoclave at a constant temperature of 400 °C with residence time of 60 min and by adjusting water content by adding distilled water or using air-dried dewatered sludge. The results showed that dewatered sludge can be directly gasified in supercritical water, with water content ranging from 75 to 95 wt%. The total gas production was increased by decreasing the water content, and the gas yield was decreased. The CO₂ yield was significantly affected by water content, whereas H₂, CH₄, and CO yields were slightly reduced. The liquid residue contained large amounts of organic matter (OM) and total phenols, thereby requiring further treatment before being discharged. The concentrations of OM and total phenols increased with a decrease in water content. Moreover, a serious carbonization reaction happened while carbon particles higher than 10 wt% (char/coke) were being formed in the solid residue.     

Hydrogen production from low temperature supercritical water Co-Gasification of low rank lignites with biomass

Co–gasification of low rank lignite (Çan) with sorghum energy crop was investigated under low temperature conditions with supercritical water (773 K, 26.9 MPa). The effects of the water volume in the reactor, blending ratios of the coal/sorghum mixtures, the use of different catalysts, and the variation of feedstock concentrations on the gasification efficiency, product distribution, and hydrogen yields were evaluated. Synergistic effects were observed for both the gasification efficiency and the hydrogen yield with a coal content of 25 wt% in the coal/biomass mixture. Increasing the initial water volume, decreasing the feedstock concentration, and using the alkali metal catalysts Na₂CO₃ and K₂CO₃ significantly increased the gasification efficiency and the hydrogen yield. In experiments with CaO, almost all the carbon dioxide formed was isolated from the gas product during gasification, and the hydrogen yield was more than 70%. The liquid products were mainly composed of alkylphenols and their derivatives.     

Valorisation of vegetable market wastes to gas fuel via catalytic hydrothermal processing

Residues of leek, cabbage and cauliflower from the market places as representatives of lignocellulosic biomass were processed via hydrothermal gasification to produce energy fuel. The experiments were carried out in a batch reactor at temperatures 300, 400, 500 and 600 °C and corresponding pressures varying in the range of 7.5–43 MPa. Natural mineral additives trona, dolomite and borax were used as homogenous catalysts to determine their effects on the gasification. More than 70 wt% of carbon in vegetable residue samples were detected in the gas phase after the hydrothermal gasification process at 600 °C. The addition of trona mineral further promoted the gasification reactions and as a result, less than 5 wt% carbon remained in the solid residue at the same temperature, degrading the biomass samples into gas and liquid products. The fuel gas with the highest calorific value was recorded to be 25.6 MJ/Nm³, from the hydrothermal gasification of cabbage at 600 °C, when dolomite was used as the homogeneous catalyst. The liquid products obtained in the aqueous phase were detected as organic acids, aldehydes, ketones, furfurals and phenols. The gas products were consisted of hydrogen, carbon dioxide, methane, and as minors; carbon monoxide and low molecular weight hydrocarbons (ethane, propane, etc.). Above 500 °C, all biomass samples yielded 50–55 vol% of CH₄ and H₂ while the CO₂ composition was around 40 vol% as the gas product.     

Valorization of sewage sludge through catalytic sub- and supercritical water gasification

Sub- and supercritical water gasification is applied to recover energy from sewage sludge in a batch reactor. The effects of reaction temperature and water-soluble additives as catalysts on gasification were examined. The resultant products, including syngas, hydrochar and liquid residues were characterized. The rise of temperature without the presence of catalysts increased the yield of H₂ (0.06 (350 °C) to 1.91 mol/kg (450 °C) and enhanced the gasification efficiency (1.29–19.61%), and decreased total organic carbon (TOC) by 68.50% in liquid residue. The changes in product distribution and characteristics of hydrochar and liquid residue implied that the organic matters in sewage sludge were dissolved and hydrolyzed in sub- and supercritical water, resulting in the production of syngas. The catalytic effect of different catalysts in relation to the H₂ gas yield was in the following order: KOH > NaOH > Na₂CO₃ ≈ K₂CO₃. In the case of catalytic supercritical water gasification at 400 °C, the highest molar fraction (37.28%) and yield of H₂ (1.60 mol/kg) were obtained in the presence of KOH. Furthermore, the scanning electron microscopy (SEM) analysis indicated that a conversion and dissolution of the organic matters in sewage sludge to liquid and gas, produced a porous, fragmented structure and disintegrated surface of hydrochar.     

Improved hydrogen storage performance of defected carbon nanotubes with Pd spillover catalysts dispersed using supercritical CO2 fluid

Hydrogen storage properties of carbon nanotubes (CNTs) modified by oxidative etching and decoration of Pd spillover catalysts are investigated. A mixed H₂SO₄/H₂O₂ solution containing ferrous ions (Fe²⁺) is useful to open the caps, to shorten the length, and to generate defects on CNTs. The Pd catalysts are deposited on the CNTs with the aid of supercritical carbon dioxide (scCO₂); as a result, a highly dispersed Pd nanoparticles and an intimate connection between Pd and carbon surface can be obtained. Combination of the two approaches can optimize a hydrogen spillover reaction on CNTs, resulting in a superior hydrogen storage capacity of 1.54 wt% (at 25 °C and 6.89 MPa), which corresponds to an enhancement factor of ∼4.5 as compared to that of pristine CNTs.     

Supercritical water gasification of real biomass feedstocks in continuous flow system

In this study, supercritical water gasification of the selected five biomass samples (cauliflower residue, acorn, tomatoes residue, extracted acorn and hazelnut shell) was investigated. Lignocellulosic feedstocks were gasified in a continuous flow reactor at 600 °C and 35 MPa. The product gas is composed of hydrogen, carbon dioxide, methane, carbon monoxide and a small amount of C₂ compounds. Quantitative analysis of product gas was performed by Gas chromatography device. Potassium carbonate (K₂CO₃) and Trona (Na₂CO₃·NaHCO₃·2H₂O) were used as catalysts. Carbon gasification efficiencies were improved by addition of these catalysts into the reacting system. Moreover, carbon gasification efficiency changes with type of biomass that includes different ratio of cellulose, hemicellulose and lignin. The H₂ yield (mol gas/kg C in feed) of acorn in the presence of Trona was found to be 7 times higher than that of without catalyst.     

Experimental study on the energy conversion of food waste via supercritical water gasification: Improvement of hydrogen production

In this study, the model food waste was gasified to hydrogen-rich syngas in a batch reactor under supercritical water condition. The model food consisted of rice, chicken, cabbage, and cooking oil. The effects of the main operating parameters including temperature (420–500 °C), residence time (20–60 min) and feedstock concentration (2–10 wt%) were investigated. Under the optimal condition at 500 °C, 2 wt% feedstock and 60 min residence time, the highest H₂ yield of 13.34 mol/kg and total gas yield of 28.27 mol/kg were obtained from non-catalytic experiments. In addition, four commercial catalysts namely FeCl₃, K₂CO₃, activated carbon, and KOH were employed to investigate the catalytic effect of additives at the optimal condition. The results showed that the highest hydrogen yield of 20.37 mol/kg with H₂ selectivity of 113.19%, and the total gas yield of 38.36 mol/kg were achieved with 5 wt% KOH addition Moreover, the low heating value of gas products from catalytic experiments with KOH increased by 32.21% compared to the non-catalytic experiment. The catalytic performance of the catalysts can be ranked in descending order as KOH > activated carbon > FeCl₃ > K₂CO₃. The supercritical water gasification (SCWG) with KOH addition can be a potential applied technology for food waste treatment with production of hydrogen-rich gases.     

Production of Gasoline and Diesel Fuels from Bio-materials

Abstract

Biomass samples were converted to charcoal and to liquid and gaseous products by pyrolysis process at different temperatures. Under pyrolysis conditions, plastic wastes can be decomposed into three fractions: gas, liquid, and solid residue. The liquid products are usually composed of higher boiling point hydrocarbons. In order to obtain useful gasoline-range hydrocarbons from the pyrolytic oil, fractional distillation is preferred for product separation. More valuable chemical raw materials including benzene, toluene, and other condensed aromatic hydrocarbons may be obtained by refining the pyrolytic oil. The vegetable oils and their soaps obtained from the vegetable oils can be pyrolyzed into hydrocarbon rich products. The yield of conversion of the sunflower oil reached the maximum 78.3% at 660 K over ZnCl₂ catalyst. The maximum gasoline yield of 48 wt% from palm oil was obtained with composite micromesoporous zeolite.     

Oleic acid gasification over supported metal catalysts in supercritical water: Hydrogen production and product distribution

Oleic acid was examined as a model compound for lipids, which was gasified in supercritical water (SCW) using a batch reactor from 400 to 500 °C at 28 MPa. The influence of operating temperature and several commercial catalysts on the gasification efficiency, hydrogen gas yield, and residual liquid product quality was examined and discussed. The main gaseous components measured were carbon dioxide (CO₂), hydrogen (H₂), methane (CH₄), and traces of carbon monoxide (CO). The residual liquid after reaction was characterized by analyzing the chemical oxygen demand (COD), total organic carbon (TOC), volatile fatty acids (VFAs), and the long chain fatty acids (LCFAs), namely, palmitic, myristic, stearic, linoleic, and oleic acids. The results showed that an increase of temperature coupled with the use of catalyst enhanced the gas yield dramatically. The H₂ yield was 15 mol/mol oleic acid converted using both the pelletized Ru/Al₂O₃ and powder Ni/Silica-alumina catalysts which gave 4 times higher than the equilibrium yield. The COD reduction efficiency ranged from 31% at 400 °C without catalyst to 96 % at 500 °C in the presence of Ni/Silica-alumina catalyst. The composition of residual liquid products was studied using gas chromatography/mass spectrometry (GC-MS), with a generalized reaction pathway for oleic acid decomposition in SCW reported.     

Assessment of supercritical water gasification of food waste under the background of waste sorting: Influences of plastic waste contents

Waste sorting is being gradually implemented as a key measure for circular and sustainable development in China, food waste will be separately collected and separated from municipal solid waste (MSW), thus the plastic content in food waste also will be reduced. In this study, supercritical water gasification (SCWG) of food waste with different contents of plastic (0–3.5 wt%) was experimentally investigated to simulate the influence of waste sorting on the food waste treatment. The results showed that lower plastic content in food waste favored higher gas yield and gasification efficiencies. The highest H₂ yield and total gas yield were 3.11 mol/kg and 8.41 mol/kg in the plastic-free case, respectively. When the plastic content decreased from 3.5 wt% to 0 wt%, the cold gas efficiency (CGE), carbon conversion efficiency (CE) and hydrogen gasification efficiency (HE) increased by 125.97%, 173.48% and 94.09%, respectively. However, lower plastic content negatively affected the quality of produced syngas through decreasing H₂ mole fraction and LHV. The solid residues from SCWG of food waste with lower plastic content had higher ratio of fixed carbon to volatile matter (FC/VM). Based on the analysis of pyrolysis properties and combustion behavior, decreasing the plastic content in food waste helped to improve the thermal stability of solid residues. Moreover, lower plastic content resulted in a decrease of total organic carbon (TOC) concentration in liquid effluent, which is favorable for further treatment of liquid effluent.     

Hydrogen production from the gasification of lignin with nickel catalysts in supercritical water

Hydrogen production from the gasification of lignin with Ni/MgO catalysts in supercritical water was conducted using stainless steel tube bomb reactor. Ni/MgO catalysts were prepared by impregnation method and were calcined at 773–1173 K in air for 8 h. The results of characterization for reduced Ni/MgO catalysts showed that Ni metal and NiO–MgO phase are formed after the reduction of calcined catalyst by _H2${\mathrm{H}}_2$. Furthermore, Ni metal surface area, which was calculated by CO chemical adsorption technique, decreased with increase in calcination temperatures. It was found that the carbon yield of gas products was increased with increase in Ni metal surface area except 10 wt% Ni/MgO (773 K) catalyst. Thus, it can be supposed that there is an optimal Ni particle size for the gasification of lignin in supercritical water. It should be noted that 10 wt% Ni/MgO (873 K) catalyst showed the best catalytic performance (carbon yield 30%) under reaction condition tested. It was concluded that Ni/MgO catalyst is a promising system for the gasification of lignin in supercritical water.     

Tuning of active nickel species in MOF-derived nickel catalysts for the control on acetic acid steam reforming and hydrogen production

Acetic acid (AcOH) steam reforming for hydrogen (H₂) generation was investigated using a zero valent nickel complex (Ni-comp) derived from a metal-organic framework precursor supported over aluminum oxide/lanthanum oxide-cerium dioxide (ALC). The effects of Ni loading ratio (10, 15, and 20 wt%) on the catacatalytic activity were investigated in the range of 400 to 650 °C to H₂ generation. The Ni-comp/ALC catalysts exhibited almost complete conversion of AcOH (X_AcOH >98%) to H₂ (X_H2>90%) alongside some impurities (e.g., carbon monoxide, methane, and carbon dioxide). A maximum H₂ yield (91.36% (0.064 mol^-1 g_cat⁻¹ h⁻¹)) was attained at the following conditions: 15 wt% Ni loading, steam to carbon molar ratio of 6.5, weight hourly space velocity of 1.05 h⁻¹, and 600 °C. The 15 wt% Ni catalyst maintained sufficient stability over 40 h reaction time. Accordingly, Ni-comp-ALC interactions were seen to efficiently improve the activity and stability of the catalyst so as to synergistically resist coke deposition and metal sintering through the formation of a large number of free Ni particles and oxygen vacancies.     

Hydrogen production from ethanol steam reforming over Ni/SiO2 catalysts: A comparative study of traditional preparation and microwave modification methods

Four silica‐supported nickel catalysts with Ni content of 10 wt% were prepared by impregnation and coprecipitation methods with or without microwave‐assisted calcination. The prepared catalysts were characterized by some techniques (BET, XRD, TEM, XPS, H₂‐TPR, etc.) and evaluated with respect to steam reforming of ethanol (SRE) for hydrogen production. The results show that the prepared Ni/SiO₂ catalysts are all very active and selective for SRE. The high activity of the four catalysts may benefit from their high specific areas and the good dispersion of active components on the carrier. The rate of carbon deposition decreases with reaction temperature especially below 450 °C. The maximum hydrogen yield of 4.54 mol H₂/mol EtOH‐reacted can be obtained over the Ni/SiO₂ catalyst by the microwave‐assisted coprecipitation method at a reaction temperature of 600 °C, EtOH/H₂O molar ratio of 1:12, liquid hourly space velocity of 11.54 h^?1 and time on stream within 600 min. The Ni/SiO₂ catalysts with microwave modification exhibits better performances of hydrogen production, stability and resistance to carbon deposition than that without microwave modification preparation, which is mainly attributed to that the microwave‐assisted treatment can decrease the catalyst acidity and enhance the interaction between metal support. Copyright © 2013 John Wiley & Sons, Ltd.     

Effect of nickel loading on hydrogen production and chemical oxygen demand (COD) destruction from glucose oxidation and gasification in supercritical water

Gasification and partial oxidation of 0.25 molar glucose solution was conducted over different metallic nickel (Ni) loadings (7.5, 11, and 18 wt%) on different catalyst supports (θ-Al₂O₃ and γ-Al₂O₃) in supercritical water. Experiments were carried out at three different temperatures (T) of 400, 450, and 500 °C at constant pressure of 28 MPa and a 30 min reaction time (t). For comparison, some experiments were conducted using high loading commercial catalyst (65 wt% Ni on Silica–alumina). Hydrogen peroxide (H₂O₂) was used as a source of oxygen in the partial oxidation experiments. Oxygen to carbon molar ratios (MR) of 0.5–0.9 were examined to increase the hydrogen production via carbon monoxide (CO) production. Results showed that in the absence of the catalyst, the optimum molar ratio was 0.8 i.e. 80% of the amount of oxygen required for complete oxidation of glucose. At a molar ratio of 0.8, the hydrogen yield was 0.3 mol/mol, as compared to 0.2 mol/mol glucose at molar ratio of 0.5 and 0.9. This optimized oxygen dose was adopted as a base line for catalysts evaluation. The main gaseous products were carbon dioxide (CO₂), carbon monoxide (CO), hydrogen (H₂), and methane (CH₄). Results also showed that the presence of Ni increased the total gas yield increased in the 7.5–18 wt Ni/Al₂O₃ catalyst. An increase in MR from 0.55 to 0.8 increased the of carbon dioxide and hydrogen yields from 1.8 to 3.8 mol/mol glucose and from 0.9 to 1.1 mol/mol. The carbon monoxide and methane yields remain constant at 2 and 0.5 mol/mol glucose, respectively. The introduction of hydrogen peroxide (H₂O₂) prior to the feed injection inhibited the catalyst activity and did not increase the hydrogen yield whereas the introduction of H₂O₂ after 15 min of reaction time increased the hydrogen yield from 0.62 mol/mol to 1.5 mol/mol. This study showed that approximately the same hydrogen yield can be obtained from the synthesized low nickel alumina loading (18 wt%) catalyst as with the 65 wt% nickel on silica–alumina loading commercial catalyst. The highest H₂ yield of 1.5 mol/mol glucose was obtained with commercial Ni/silica–alumina with a BET surface area of 190 m²/g compared to 1.2 mol/mol with the synthesized Ni/θ alumina with a BET surface area of 46 m²/g.     

Hydrogen production from oxidative steam reforming of ethanol over Ir catalysts supported on Ce–La solid solution

The Ce_1?xLa_xO_2?δ solid solution (CL) supported Ir (nIr/CL, n = 2, 5 and 10 wt.%) catalysts are studied for H₂ production from ethanol oxidative steam reforming (OSR). The Ir dispersion, surface area, oxygen vacancy density and carbon deposition resistance of nIr/CL catalysts are greatly enhanced compared with Ir/CeO₂. Among the tested catalysts, 5%Ir/CL shows the best catalytic performance, exhibiting >99.9% ethanol conversion at 400 °C with H₂ yield rate of 323 μmol·g_cata^?1·s^?1 and no obvious carbon deposition after used. The 5%Ir/CL catalyst contains the highest amount of reducible interface Ce⁴⁺, leading to a strong interaction with surface Ir species at the metal-support interface during the OSR reaction. The strong interaction induces Ir to be well dispersed on the CL support, and is associated with more redox-active sites (interface Ce⁴⁺/Ce³⁺), to guarantee high activity.     

Effect of phosphoric acid and acetic acid addition on the hydrogen evolution using Ni based catalyst prepared in ethanol,methanol, and water solvents

Ni-based catalysts were synthesized in water, methanol and ethanol solvents by chemical reduction with sodium borohydride (NaBH₄). The obtained catalyst for the first time was used to catalyze the NaBH₄ hydrolysis reaction with phosphoric acid and acetic acid including different concentrations. The maximum hydrogen production rates obtained in the hydrolysis reaction including 0.5 M phosphoric acid and 0.1 M acetic acid of the Ni-based catalyst prepared in ethanol solvent were 5214 and 3650 ml g^?1 min^?1, respectively.     

Pyrolysis of soybean oil with H-ZSM5 (Proton-exchange of Zeolite Socony Mobil #5) and MCM41 (Mobil Composition of Matter No. 41) catalysts in a fixed-bed reactor

Soybean oil was pyrolyzed with various catalysts in a fixed-bed reactor under nitrogen flow at 420 and 450 °C. The H-ZSM5 catalysts (molar ratio SiO₂/Al₂O₃ = 28, 40, and 180) and 2 wt% (Ga, Al or Cu) impregnated MCM41 catalysts were used in order to investigate the effect of catalysts during the pyrolysis process. The gas products in all experiments were mainly methane, ethane and propylene. The liquid products in the presence of H-ZSM5 catalysts were mainly aromatic components while those with metal/MCM41 catalysts were a mixture of alkanes, alkenes, alkadienes, aromatic and carboxylic acids. The highest coke yield of 4.4 wt% was obtained with Ga/MCM41 catalyst at the pyrolysis temperature of 420 °C. The effect of catalysts on product yield and composition was systematically investigated.