Solubility of cyproheptadine in supercritical carbon dioxide; experimental and modeling approaches

Solubility of solute in supercritical fluids at different pressures and temperatures is one of the most important parameters necessary for design of any supercritical fluid-based processes. Among different supercritical fluids, carbon dioxide is one of the most widely used solvents due to its useful and green characteristics. In this work, with the assist of supercritical carbon dioxide as the solvent, solubility of cyproheptadine in different temperatures (308–338 K) and pressures (160–400 bar) are measured using static method. The obtained results demonstrated that solubility of cyproheptadine ranged between 3.35 × 10⁻⁵ and 3.09 × 10⁻³ based on mole fraction. A closer examination of measured solubility data show that not only solubility of cyproheptadine increases by increasing pressure but also experiences a cross over pressure about 200 bar. At last, the measured solubility data are correlated using four widely used density based correlations namely Mendez Santiago–Teja (MST), Kumar and Johnston (KJ), Bartle et al., and Chrastil models. The obtained results demonstrated that the best correlative capability was observed for KJ model leads to the average absolute relative deviation percent (AARD %) of 6.3%.     

Supercritical CO2 and highly selective aromatase inhibitors: Experimental solubility and empirical data correlation

The solubility of highly selective and potent third-generation aromatase inhibitors includes the non-steroidal agents letrozole and anastrozole and the steroid exemestane in supercritical carbon dioxide (SC-CO₂) has been investigated. The experiments were carried out using the simple and static method at pressures in the range of 12.1–35.5 MPa and temperatures ranging from 308 to 348 K. The mole fraction solubilities ranged from 0.22 × 10⁻⁵ to 1.88 × 10⁻⁴. Solubility data were correlated using six empirical models (Chrastil model, dV–A model, K–J model, Bartle model, Yu model and Gordillo model). The results showed that these models can be applied to satisfactory solubility predictions at different pressures and temperatures. A comparison among the six models revealed that the K–J, and Gordillo models gave much better correlations of the solubility data with an average absolute relative deviation (AARD%) ranging from 0.2 to 2.3 and from 1.6 to 2.5%, respectively. Using the correlation results, the heat of drug–CO₂ solvation and that of drug vaporization was separately approximated in the range of −17.3 to −17.5 and 93.0–112.1 kJ mol⁻¹.     

Solubility of gabapentin in supercritical carbon dioxide

The purpose of this study was to measure the solubility of gabapentin in supercritical carbon dioxide at different pressures and temperatures of 16–40 MPa and 308–338 K, respectively. The measured solubility data revealed that solubility of gabapentin was 8.97 × 10⁻⁵–7.36 × 10⁻³ based on the mole fraction in supercritical carbon dioxide at the aforementioned operational conditions. At last, the obtained results were correlated using four density based semi-empirical correlations namely Bartle et al., Mendez-Santiago and Teja (MST), Chrastil and Kumar and Johnston (K–J). The results revealed that according to the obtained average absolute relative deviations (AARD) for the used density based correlations of MST (AARD % = 9.88%), Chrastil (AARD % = 9.47%), K–J (AARD % = 11.5%) and Bartle et al. (AARD % = 9.29%), none of the correlations can be considered as the most accurate one. In other words, all the examined semi-empirical correlations are in the same level of accuracy.     

Solubility of chlorpheniramine maleate in supercritical carbon dioxide

Solubility of chlorpheniramine maleate in supercritical carbon dioxide at different temperatures (308–338 K) and pressures (160–400 bar) is measured using static method coupled with gravimetric method. The measured solubility data demonstrated that the solubility of chlorpheniramine maleate was changed between 1.54 × 10⁻⁵ and 4.26 × 10⁻⁴ based on the mole fraction as the temperature and pressure are changed. The general trend of measured solubility data shows a direct effect of pressure and temperature on the solubility of chlorpheniramine maleate. Finally, the obtained solubilities correlated using four semi-empirical density-based correlations including Mendez Santiago–Teja (MST), Kumar and Johnston (KJ), Bartle et al., and Chrastil models. Although the results of modeling showed that the KJ model leads to the average absolute relative deviation percent (AARD %) of 8.1% which is the lowest AARD %, deviation of other utilized correlations are rather the same.     

Solubility of niflumic acid and celecoxib in supercritical carbon dioxide

The solubility data of two fluorinated and non-steroidal anti-inflammatory drugs, niflumic acid (CAS No. 4394-00-7) and celecoxib (CAS No. 169590-42-5), in supercritical carbon dioxide were measured with a semi-flow type phase equilibrium apparatus at temperatures ranging from 313.2 K to 353.2 K and pressures up to 31 MPa. At the highest extraction temperature and pressure, the solubilities are 2.09 × 10⁻⁵ and 1.52 × 10⁻⁵ in mole fraction for niflumic acid and celecoxib, respectively. The saturated solubility data were correlated with the Chrastil model, the Mendez-Santiago–Teja equation, and the Peng–Robinson equation of state. The Chrastil model fitted the experimental data to about within the experimental uncertainty. The correlated results of the Mendez-Santiago–Teja model confirmed the consistency of the solubility data over the entire experimental conditions. Incorporating with two-parameter van der Waals one-fluid mixing rules, the Peng–Robinson equation of state represents satisfactorily the gas–solid equilibrium behavior of niflumic acid and celecoxib in supercritical carbon dioxide.     

Measurement and correlation solubility of cefixime trihydrate and oxymetholone in supercritical carbon dioxide (CO2)

The equilibrium solubilities of cefixime trihydrate and oxymetholone in supercritical carbon dioxide (CO₂) were measured using a “static method”. Cefixime trihydrate is a cephalosporin antibiotic drug and Oxymetholone is a 17alpha-alkylated anabolic-androgenic steroid drug. The experimental measurements for cefixime trihydrate were performed at temperatures of 308, 318 and 328 K as well as pressure range from 183 to 335 bar. The solubility of oxymetholone was determined at 308, 318 and 328 K and pressure range from 121 to 305 bar. The experimental solubility data (mole fraction) for cefixime trihydrate and oxymetholone was greater than 1.6 × 10⁻⁷ and 1.6 × 10⁻⁵ and less than 3.02 × 10⁻⁷ and 1.49 × 10⁻⁴, respectively. The solubilities for two drugs in CO₂ were correlated by using four semi-empirical models such as Bartle, Kumar and Johnstone (K–J), Mendez-Santiago and Teja (M–T) and Chrastil models. The results obtained from the semi-empirical models show that there is good agreement between the experimental data and the results of semi-empirical models. By using the correlation results, the heat of drug–CO₂ solvation and heat of drug vaporization for cefixime–CO₂ and oxymetholone–CO₂ systems may be approximately estimated. Also, the Peng–Robinson (PR) cubic equation of state (CEOS) along with the van der Waals combining rule was applied to correlate the drugs solubilities in supercritical CO₂. The average absolute deviation between the experimental data and the results of PR equation for cefixime trihydrate and oxymetholone was 11.92% and 11.74%, respectively.     

Representing experimental solubility of phenylephrine hydrochloride in supercritical carbon dioxide and modeling solute solubility using semi-empirical correlations

Phenylephrine is used as a decongestant sold as an oral medicine, as a nasal spray, or as eye drops. Phenylephrine is now the most common over-the-counter decongestant in the United States. In this regard, measuring the solubility of phenylephrine hydrochloride seems applicable in supercritical carbon dioxide-based processes dealing with this drug. The obtained solubility data obtained by a static method coupled with gravimetric method were in the range of 1.01 × 10⁻⁴ to 2.89 × 10⁻³ based on the mole fraction at the different temperature and pressure ranges of 308.15–338.15 K and 160–400 bar, respectively. In addition, the solubility data were used to obtain the adjusting parameters of semi-empirical correlations namely Kumar and Johnston, Bartle et al., Chrastil and Mendez-Santiago-Teja using a simple data regression.     

Lycopene solubility in mixtures of carbon dioxide and ethyl acetate

In order to improve the efficiency of processes using supercritical (sc) carbon dioxide (CO₂) to micronize the carotenoid “lycopene”, it is important to know the solubility of lycopene in mixtures of the organic solvent ethyl acetate (EA) and the antisolvent CO₂ at elevated pressures. The solubility of lycopene has been determined for different temperatures (313–333 K), pressures (12–16 MPa) and CO₂ molar fractions (0.58–1). The obtained data show that CO₂ acts as an antisolvent in the system lycopene/EA/CO₂ in the range of CO₂/EA ratios studied. The solubility of lycopene is rather small with lycopene molar fractions ranging from 0.1 × 10⁻⁶ to 46 × 10⁻⁶. The solubility of lycopene increases with temperature, pressure and EA concentration.     

Analyzing the solubility of fluoxetine hydrochloride in supercritical carbon dioxide

In the pharmaceutical industry where the supercritical fluid-based technologies are utilized it is very important and vital to know the accurate value of the equilibrium solubility of solids required for the engineers to determine the size of the equipments. According to this requirement, the purpose of this study was measuring the solubility of fluoxetine hydrochloride with IUPAC name of 3-phenyl-3-[4-(trifluoromethyl)phenoxy]propan-1-amine hydrochloride using a static method coupled with gravimetric method. The measured solubility data at the temperature and pressure range of 308.15–338.15 K and 16–40 MPa was ranged between 2.65 × 10⁻⁵ and 8.12 × 10⁻⁴ based on the mole fraction. The results revealed that the solubility was increased when the pressure was increased while the effect of the temperature was more complex. Finally, the measured solubility data were correlated using three different correlations namely Bartle et al., Mendez-Santiago–Teja and Kumar and Johnston. The results of modeling revealed that the Bartle et al. model leads to the lowest average absolute relative deviation (AARD %) of 9.48.     

Near critical and supercritical impregnation and kinetic release of thymol in LLDPE films used for food packaging

The impregnation of organic compounds in polymeric materials using supercritical carbon dioxide (scCO₂) is a well-known technique, which is currently used in drug/polymer formulation. In this work, near critical and supercritical impregnation of thymol in linear low-density polyethylene (LLDPE) films was done in order to develop a new technique for preparation of active polymers to be used as food packages. The properties of thymol as a natural antimicrobial and antioxidant agent have motivated this study about the assessment of its migration from the polymer to different food simulant. Impregnation assays of thymol in LLDPE films were done in a high-pressure cell, where pure thymol was solubilized in supercritical carbon dioxide at 313 K and pressures varying from 7 to 12 MPa. This procedure allowed the preparation of plastic films with thymol concentrations ranged between 5100 and 13,200 ppm. Migration tests showed that the pressure applied during the impregnation procedure is a key parameter that affects the content of the active compound into the polymer, since thymol solubility in scCO₂ and absorption phenomena in the polymer increased with the pressure. The correlation between experimental data and a phenomenological transfer model allowed the estimation of the diffusion coefficient of thymol in LLDPE, which was ranged from 7.5 × 10⁻¹³ to 3.0 × 10⁻¹² m² s⁻¹.     

Measurement and correlation of the solubility of two steroid drugs in supercritical carbon dioxide using semi empirical models

The solubilities of desoxycorticosterone acetate (DA) and clobetasole propionate (CP) in supercritical carbon dioxide (SC-CO₂) were measured at temperature ranging from (308 to 348) K and pressures from (12.2 to 35.5) MPa using a static method. The mole fraction solubilities ranged from 10⁻⁷ to 13.93 × 10⁻⁵. The crossover region was observed for DA and CP at 24.3 and 25.3 MPa, respectively. Solubility data were correlated using four semi-empirical density-based models (Chrastil, Bartle, Kumar, Johnston (K–J) and Mendez-Santiago and Teja (M–T) models). The average absolute relative deviations (AARD%) ranged from 9.3 to 13.6; 8.9 to 11.9; 6.5 to 10.3 and from 10.4 to 13.4 for Chrastil, Bartle, K–J and M–T models, respectively. A comparison among the four models revealed that the K–J model gave much better correlation of the solubilities in comparison with other models. Using the correlation results, the heat of drug–CO₂ solvation and that of drug vaporization was separately approximated in the range of −24.2 to −24.5 and 63.8 to 64.8 kJ mol⁻¹. The correlation results showed good agreement with the experimental data.     

Solubilities of chlormezanone,metaxalone and methocarbamol in supercritical carbon dioxide

The solubilities of three active pharmaceutical ingredients (APIs) in supercritical carbon dioxide were measured in this study using a semi-flow apparatus. These APIs are chlormezanone (C₁₁H₁₂ClNO₃S), metaxalone (C₁₂H₁₅NO₃) and methocarbamol (C₁₁H₁₅NO₅) that are all used as skeletal muscle relaxants. The solubility data are reported for three isotherms at 308.2, 318.2 and 328.2 K, with the pressure range from 12 to 24 MPa. Most solubility data are within the range of 10⁻⁶ to 10⁻⁴ mole fraction for each API. The crossover phenomena were observed from the experimental results for all three systems. These solubility data satisfied the thermodynamic consistency tests. They were then correlated using three semi-empirical models. With the optimally fitted binary interaction parameters, satisfactory correlation agreement is presented for each binary mixture.     

High-pressure phase equilibria for the binary system carbon dioxide + dibenzofuran

The experimental solubility of dibenzofuran in near-critical and supercritical carbon dioxide and the solid–liquid–vapor (SLV) equilibrium line for the CO₂ + dibenzofuran system are reported. The built in-house static view cell apparatus used in these measurements is described. The solubility of naphthalene in supercritical CO₂ and the CO₂ + naphthalene SLV line are also determined in order to assess the reliability and accuracy of the measurement technique. The solubility of dibenzofuran in carbon dioxide is determined at 301.3, 309.0, 319.2, 328.7 and 338.2 K in the 6–30 MPa pressure range. Solubility data are correlated using the Chrastil model and the Peng–Robinson equation of state. This equation is also used to predict the CO₂ + dibenzofuran SLV line. Results show the feasibility of using supercritical CO₂ to extract dibenzofuran.     

Extraction of jojoba seed oil using supercritical CO2+ethanol mixture in green and high-tech separation process

In this study, the extraction of jojoba seed oil obtained from jojoba seed using both supercritical CO₂ and supercritical CO₂+ethanol mixtures was investigated. The recovery of jojoba seed oil was performed in a green and high-tech separation process. The extraction operating was carried out at operating pressures of 25, 35 and 45 MPa, operating temperatures of 343 and 363 K, supercritical fluid flow rates of 3.33 × 10⁻⁸, 6.67 × 10⁻⁸ and 13.33 × 10⁻⁸ m³ s⁻¹, entrainer concentrations of 2, 4 and 8 vol.%, and average particle diameters of 4.1 × 10⁻⁴, 6.1 × 10⁻⁴, 8.6 × 10⁻⁴ and 1.2 × 10⁻³ m. It was found that a green chemical modifier such as ethanol could enhance the solubilities, initial extraction rate and extraction yield of jojoba seed oil from the seed matrix as compared to supercritical CO₂. In addition, it was found that the solubility, the initial extraction rate and the extraction yield depended on operating pressure and operating temperature, entrainer concentration, average particle size and supercritical solvent flow rate. The solubility of jojoba seed oil and initial extraction rate increased with temperature at the operating pressures of 35 and 45 MPa and decreased with increasing temperature at the operating pressure of 25 MPa. Furthermore, supercritical fluid extraction involved short extraction time and minimal usage of small amounts entrainer to the CO₂. About 80% of the total jojoba seed oil was extracted during the constant rate period at the pressure of 35 and 45 MPa.     

Acid-catalysed methanolysis reaction of non-polar triazinyl reactive dyes in supercritical carbon dioxide

An extensive study of the reaction mechanism of the methanolysis reaction of triazinyl systems of non-polar reactive dyes has been done in a neutral, moderately acidic and strongly acidic medium. In a neutral reaction medium, dichlorotriazines are more reactive than the monochlorotriazines. However, in a moderately acidic medium, as supercritical carbon dioxide, an inversion in the reactivity pattern of monochlorotriazines was observed, which is related to the dye structure. Amines as substituent group attached to the triazinyl ring showed the largest conversion and k values, approaching those values of dichlorotriazine. Protonation of the ring, and stabilization of the positive charge in the triazinyl ring due to the mesomeric effect, explain the reactivity increased of monochlorotriazines. When acids were added to the reaction medium, resulting in an increase of the acid concentration, the reactivity of monochlorotriazinyl dyes was surprisingly much larger than dichlorotriazine; k values increased up to a factor of 54. The largest k was measured for the monochlorotriazinyl dye, S1Cl–NH₂, showing a value of 3.0 × 10⁻³ s⁻¹, while a value of 3.2 × 10⁻⁴ s⁻¹ was measured in supercritical carbon dioxide. In a strongly acidic medium, the reactivity of triazinyl reactive dyes is substantially influenced by the basicity of the substituted groups in the reactive group, and in the chromophore. Based on this kinetic study, the dyeing of cotton in supercritical carbon dioxide under acidic conditions seems to be very promising when triazinyl dyes are used.     

Supercritical carbon dioxide extraction of Gac oil

Supercritical carbon dioxide extraction of Gac (Momordica cochinchinensis Spreng) aril was performed at pressures ranging from 200 to 400 bar, temperatures from 313 to 343 K and specific flow rates from 50 to 90 kg h⁻¹ CO₂ kg⁻¹ Gac aril. Total oil recovery and carotenes concentration were investigated in the course of extraction. Mathematical modelling of oil solubility data was also performed. The results showed that at specific flow rate of 70 kg h⁻¹ kg⁻¹, pressure of 400 bar and temperature of 343 K, Gac oil recovery exceeded 95% after 120 min of extraction. Gac oil loading of supercritical carbon dioxide was successfully described by Chrastil's model. Carotenes concentration of extracted Gac oil was found at level of thousands of ppm.     

Deposition of aromatic polyimide thin films in supercritical carbon dioxide

The deposition of aromatic polyimide (API) thin films was carried out in supercritical carbon dioxide (scCO₂) with 20 mol% of N,N-dimethylformamide (DMF) as a cosolvent, and using 4,4′-diaminodiphenyl ether (ODA) and pyromellitic dianhydride (PMDA) as monomers. A new apparatus based on a flow method that consisted of a cold-wall type reactor and two supply lines for each of the API monomers was used. The effect on the morphology of the films was investigated at feeding monomer concentrations and deposition temperatures ranging from 5 × 10⁻⁴ to 5 × 10⁻⁶ on a mole fraction basis and from 423 to 523 K, respectively. The results showed that increasing the monomer concentration and decreasing the deposition temperature increased the thickness of the films, and a smooth surface of the film was obtained at 423 K. Additionally, FT-IR study and thermogravimetric (TG) analysis of the film deposited at monomer mole fractions of 5 × 10⁻⁵ and at a deposition temperature of 473 K were also carried out. The FT-IR spectrum of the deposited film in scCO₂ with DMF represented imide structures although there was a small peak of amide carbonyl stretching that originated from the polyamic acid and DMF. The TG curve indicated the temperature of 5% weight loss was more than 800 K under an air atmosphere after complete imidization.     

A predictive method for the solubility of drug in supercritical carbon dioxide

We present a predictive approach for the solubility of drug in supercritical CO₂. The fugacity of drug in the solid phase is estimated from its melting temperature and heat of fusion, and the fugacity of the drug in its hypothetical liquid state. The fugacity of the drug is calculated from the Peng–Robinson (PR) EOS. Temperature and composition dependence of the interaction parameters a(T,x) and b(x) of the PR EOS are obtained from the quantum mechanics-based, COSMO-SAC solvation model. As a consequence, the method does not require input of experimental data of the mixture. The average logarithmic deviation (ALD-x) in predicted solubility of 46 drugs in subcritical and supercritical carbon dioxide (T = 293.15–473 K, P = 8.5–50 MPa, and 1160 solubility data ranging from 10⁻⁷ to 10⁻²) was found to be 0.81 (a factor of 5.3). The same method was also examined for solid solubility in a variety of solvents (60 solids including 34 different solvents (with different polarities) and 190 drug-solvent pairs) at ambient pressure. The ALD-x was found to be slightly better (0.58 or a factor of 2.89). The proposed method, the PR + COSMOSAC EOS, is thus a useful tool for a priori prediction of solid solubility in scCO₂, as well as for other solvents.     

High-pressure phase equilibrium measurements and thermodynamic modeling for the systems involving CO2, ethyl esters (oleate,stearate, palmitate) and acetone

The aim of this work was to study the phase behavior of systems involving carbon dioxide (CO₂), fatty acid ethyl esters (ethyl oleate, ethyl stearate and ethyl palmitate) and acetone at high pressures. The phase behavior involving these components is an important step regarding the design and optimization of industrial processes based on supercritical conditions, such as biodiesel production and fatty esters fractionation involving supercritical and/or pressurized solvents. In addition, supercritical CO₂ can offer an interesting alternative for glycerol separation in water-free biodiesel purification processes. The binary systems investigated in this work were CO₂ + ethyl oleate, and CO₂ + ethyl stearate and these were compared with the CO₂ + ethyl palmitate system. The ternary CO₂ + ethyl palmitate + acetone was also investigated at two different ethyl palmitate to acetone molar ratios of (1:1) and (1:3). The static synthetic method using a variable-volume view cell was employed to obtain the experimental data in the temperature range of 303.15–353.15 K. Vapor–liquid (VL), liquid–liquid (LL) and vapor–liquid–liquid (VLL) phase transitions were observed in these systems. In the binary systems, the solubility increased with the presence of unsaturation and decreased with the number of carbon atoms in the fatty ester chain. Addition of acetone as well as ethanol eliminated the liquid–liquid immiscibility and reduced the pressure transitions, therefore increasing the solubility of the ester in supercritical CO₂. The experimental data sets for the binary and ternary systems were successfully modeled using the Peng–Robinson equation of state with the classical van der Waals quadratic mixing rule (PR-vdW2) and Wong-Sandler (PR-WS) mixing rule. Both models showed good performance in the phase equilibrium correlations and in predictions for the binary and ternary systems.     

Phase behavior of 1,3,5-tri-tert-butylbenzene–carbon dioxide binary system

1,3,5-tri-tert-butylbenzene (TTBB) is solid at ambient conditions, and has substantial solubility in liquid and supercritical carbon dioxide. We present the phase behavior of TTBB–CO₂ binary system at temperatures between 298 and 328 K and at pressures up to 20 MPa. Phase diagrams showing the liquid–vapor, solid–liquid and solid–vapor equilibrium envelopes are constructed by pressure–volume–temperature measurements in a variable-volume sapphire cell. TTBB is highly soluble in CO₂ over a wide range of compositions. Single-phase states are achieved at moderate pressures, even with very high TTBB concentrations. For example, at 328 K, a binary system containing TTBB at a concentration of 95% by weight forms a single-phase above 2.04 MPa. TTBB exhibits a significant melting-point depression in the presence of CO₂, 45 K at 3.11 MPa, where the normal melting point of 343 K is reduced to 298 K. With its high solubility in carbon dioxide, TTBB has potential uses as a binder or template in materials forming processes using dense carbon dioxide.