Pyroelectric properties of BST/PLT composite thick films with addition of xPbO–(1 − x)B2O3 glass

The Ba_xSr_1−xTiO₃ (BST)/Pb_1−xLa_xTiO₃ (PLT) composite thick films (20 μm) with 12 mol% amount of xPbO–(1 − x)B₂O₃ glass additives (x = 0.2, 0.35, 0.5, 0.65 and 0.8) have been prepared by screen-printing the paste onto the alumina substrates with silver bottom electrode. X-ray diffraction (XRD), scanning electron microscope (SEM) and an impedance analyzer and an electrometer were used to analyze the phase structures, morphologies and dielectric and pyroelectric properties of the composite thick films, respectively. The wetting and infiltration of the liquid phase on the particles results in the densification of the composite thick films sintered at 750 °C. Nice porous structure formed in the composite thick films with xPbO–(1 − x)B₂O₃ glass as the PbO content (x) is 0.5 ≥ x ≥ 0.35, while dense structure formed in these thick films as the PbO content (x) is 0.8 ≥ x ≥ 0.65. The volatilization of the PbO in PLT and the interdiffusion between the PLT and the glass lead to the reduction of the c-axis of the PLT phase. The operating temperature range of our composite thick films is 0–200 °C. At room temperature (20 °C), the BST/PLT composite thick films with 0.35PbO–0.65B₂O₃ glass additives provided low heat capacity and good pyroelectric figure-of-merit because of their porous structure. The pyroelectric coefficient and figure-of-merit F_D are 364 μC/(m² K) and 14.3 μPa^−1/2, respectively. These good pyroelectric properties as well as being able to produce low-cost devices make this kind of thick films a promising candidate for high-performance pyroelectric applications.     

Glass-free LTCC microwave dielectric ceramics

The sintering behavior, microstructure and microwave dielectric properties of complex pyrophosphate compounds AMP₂O₇ (A = Ca, Sr; M = Zn, Cu) were investigated in this paper. All compounds could be densified below the temperature of 950 °C without any glass addition, and exhibit low permittivity (_r < 8), high Q × f value and negative temperature coefficient of resonant frequency. The Q × f value was discussed from the point of view of bond strength. The chemical compatibility with silver and copper was also investigated. All compounds seriously react with silver at 700 °C. However SrZnP₂O₇ could be co-fired with copper in reduced atmosphere. The microwave dielectric properties of SrZnP₂O₇ sintered at 950 °C in reducing atmosphere are: _r = 7.06, Q × f = 52781 GHz, τ_f = −70 ppm/°C. In terms of its lower sintering temperature, chemical compatibility with copper and good microwave dielectric properties, SrZnP₂O₇ ceramic is very promising for low temperature co-fired ceramic (LTCC) applications.     

Preparation and optical properties of sol–gel derived Er-doped Al2O3–Ta2O5 films

Thin films of the system xAl₂O₃–(100 − x)Ta₂O₅–1Er₂O₃ were prepared by a sol–gel method and a dip-coating technique. The influences of the composition and the crystallization of the films on Er³⁺ optical properties were investigated. Results of X-ray diffraction indicated that the crystallization temperature of Ta₂O₅ increased from 800 to 1000 °C with increased values of x. In crystallized films, the intensities of the visible fluorescence and upconversion fluorescence tend to decrease with an increase in x values, due to the high phonon energy of Al₂O₃; the strongest fluorescence is observed in a crystallized film for x = 4 heat treated at 1000 °C. In amorphous films obtained by heat treatment at relatively low temperatures the Er³⁺ fluorescence could not be observed because strong fluorescence from organic residues remaining in the films thoroughly covered the Er³⁺ fluorescence. On the other hand, the Er³⁺ upconversion fluorescence in the amorphous films was observed to be stronger than that in the crystallized films. The strongest upconversion fluorescence is observed in an amorphous film for x = 75 heat treated at 800 °C.     

Spectroscopic ellipsometry analysis of GaAs1 − xNx layers grown by molecular beam epitaxy

In this work, we present the effect of nitrogen incorporation on the dielectric function of GaAsN samples, grown by molecular beam epitaxy (MBE) followed by a rapid thermal annealing (for 90 s at 680 °C). The GaAs_1 − xN_x samples with N content up to 1.5% (x = 0.0%, 0.1%, 0.5%, 1.5%), are investigated using room temperature spectroscopic ellipsometry (SE). The optical transitions in the spectral region around 3 eV are analyzed by fitting analytical critical point line shapes to the second derivative of the dielectric function. It was found that the features associated with E₁ and E₁ + Δ₁ transitions are blue-shifted and become less sharp with increasing nitrogen incorporation, in contrast to the case of E₀ transition energy in GaAs_1 − xN_x. An increase of the split-off Δ₁ energy with nitrogen content was also obtained, in agreement to results found with MOVPE GaAs_1 − xN_x grown samples.     

Sintering behavior and microwave dielectric properties of Bi3(Nb1−xTax)O7 solid solutions

Solid solutions of Bi₃(Nb_1−xTa_x)O₇ (x = 0.0, 0.3, 0.7, 1) were synthesized using solid state reaction method and their microwave dielectric properties were first reported. Pure phase of fluorite-type could be obtained after calcined at 700 °C (2 h)⁻¹ between 0 ≤ x ≤ 1 and Bi₃(Nb_1−xTa_x)O₇ ceramics could be well densified below 990 °C. As x increased from 0.0 to 1.0, saturated density of Bi₃(Nb_1−xTa_x)O₇ ceramics increased from 8.2 to 9.1 g cm⁻³, microwave permittivity decreased from 95 to 65 while Q_f values increasing from 230 to 560 GHz. Substitution of Ta for Nb modified temperature coefficient of resonant frequency τ_f from −113 ppm °C⁻¹ of Bi₃NbO₇ to −70 ppm °C⁻¹ of Bi₃TaO₇. Microwave permittivity, Q_f values and τ_f values were found to correlate strongly with the structure parameters of fluorite solid solutions and the correlation between them was discussed in detail. Considering the low densified temperature and good microwave dielectric proprieties, solid solutions of Bi₃(Nb_1−xTa_x)O₇ ceramics could be a good candidate for low temperature co-fired ceramics application.     

Influence of Mn doping on microstructure and DC-accelerated aging behaviors of ZnO–V2O5-based varistors

The microstructure, electrical properties, dielectric characteristics, and DC-accelerated aging behavior of the ZnO–V₂O₅–MnO₂ system sintered were investigated for MnO₂ content of 0.0–2.0 mol% by sintering at 900 °C. For all samples, the microstructure of the ZnO–V₂O₅–MnO₂ system consisted of mainly ZnO grain and secondary phase Zn₃(VO₄)₂. The incorporation of MnO₂ to the ZnO–V₂O₅ system was found to restrict the abnormal grain growth of ZnO. The nonlinear properties and stability against DC-accelerated aging stress improved with the increase of MnO₂ content. The ZnO–V₂O₅–MnO₂ system added with MnO₂ content of 2.0 mol% exhibited not only a high nonlinearity, in which the nonlinear coefficient is 27.2 and the leakage current density is 0.17 mA/cm², but also a good stability, in which %ΔE_1 mA = −0.6%, %Δ = −26.1%, and %Δtan δ = +22% for DC-accelerated aging stress of 0.85E_1 mA/85 °C/24 h.     

A simple and an effective method for the fabrication of densified glass-ceramics of low temperature co-fired ceramics

This study reports a new, simple and effective pre-calcined method for fabrication BaO–TiO₂–B₂O₃–SiO₂ low temperature co-fired ceramics (LTCC) at a sintering temperature below 900 °C, and with dielectric losses (tan δ) lower than 2 × 10⁻³. The research results have shown that the addition of 2–5 wt% Al₂O₃ could easily eliminate the porosity of the glass-ceramics because of the excellent wetting behavior between alumina and the BaO–B₂O₃–SiO₂ glass liquid phase in the low temperature co-fired ceramic system.     

Influence of rare-earth oxides on structure and crystallization properties of Bi2O3–B2O3 glass

Bi₂O₃·B₂O₃ glasses doped with rare-earth oxides (RE₂O₃) (RE³⁺ = La³⁺, Pr³⁺, Sm³⁺, Gd³⁺, Er³⁺ and Yb³⁺) were prepared by the melting–quenching method. The relationships between composition and properties were demonstrated by IR, DSC, XRD and SEM analysis. The results show that the network structure resembles that of undoped Bi₂O₃·B₂O₃ glass, composing of [BO₃], [BO₄] and [BiO₆] units. RE₂O₃ stabilizes the glass structure as a modifier. Transition temperature (T_g) increases linearly with cationic field strength (CFS) of RE³⁺. La₂O₃, Pr₂O₃, Sm₂O₃ and Gd₂O₃ are benefit to promote the formation of BiBO₃ crystal. When Er₂O₃ and Yb₂O₃ are introduced, respectively, the main crystal phase changes to Bi₆B₁₀O₂₄. Transparent surface crystallized samples are obtained by reheating at 460–540 °C for 5 h. In this case, needle like BiBO₃ crystal or rare-earth-doped BiBO₃ crystal (Pr_xBi_1−xBO₃ and Gd_xBi_1−xBO₃) are observed, which is promising for non-linear optical application.     

Structural and optical properties of (100 − x)(Li2B4O7) − x(SrO–Bi2O3–0.7Nb2O5–0.3V2O5) glasses and glass nanocrystal composites

Glasses of various compositions in the system (100 − x)(Li₂B₄O₇) − x(SrO–Bi₂O₃–0.7Nb₂O₅–0.3V₂O₅) (10  x  60, in molar ratio) were prepared by splat quenching technique. The glassy nature of the as-quenched samples was established by differential thermal analyses (DTA). The amorphous nature of the as-quenched glasses and crystallinity of glass nanocrystal composites were confirmed by X-ray powder diffraction studies. Glass composites comprising strontium bismuth niobate doped with vanadium (SrBi₂(Nb_0.7V_0.3)₂O_9−δ (SBVN)) nanocrystallites were obtained by controlled heat-treatment of the as-quenched glasses at 783 K for 6 h. High resolution transmission electron microscopy (HRTEM) of the glass nanocrystal composites (heat-treated at 783 K/6 h) confirm the presence of rod shaped crystallites of SBVN embedded in Li₂B₄O₇ glass matrix. The optical transmission spectra of these glasses and glass nanocrystal composites of various compositions were recorded in the wavelength range 190–900 nm. Various optical parameters such as optical band gap (E_opt), Urbach energy (ΔE), refractive index (n), optical dielectric constant and ratio of carrier concentration to the effective mass (N/m^*) were determined. The effects of composition of the glasses and glass nanocrystal composites on these parameters were studied.     

Dielectric and piezoelectric properties of sol–gel derived Ca doped PbTiO3

Synthesis of Ca doped PbTiO₃ powder by a chemically derived sol–gel process is described. Crystallization characteristics of different compositions Pb_1−xCa_xTiO₃ (PCT) with varying calcium (Ca) content in the range x = 0–0.45 has been investigated by DTA/TGA, X-ray diffraction and scanning electron microscopy. The crystallization temperature is found to decrease with increasing calcium content. X-ray diffraction reveals a tetragonal structure for PCT compositions with x ≤ 0.35, and a cubic structure for x = 0.45. Dielectric properties on sintered ceramics prepared with fine sol–gel derived powders have been measured. The dielectric constant is found to increase with increasing Ca content, and the dielectric loss decreases continuously. Sol–gel derived Pb_1−xCa_xTiO₃ ceramics with x = 0.45 after poling exhibit infinite electromechanical anisotropy (k_t/k_p) with a high d₃₃ = 80 pC/N, ′ = 298 and low dielectric loss (tan δ = 0.0041).     

Ultraviolet emitting (Y1−xGdx)2O3−δ thin films deposited by radio frequency magnetron sputtering: Combinatorial modeling, synthesis, and rapid characterization

Gadolinium-doped, yttrium oxide thin films have been deposited on silicon (001) substrates by radio-frequency (RF) magnetron reactive sputtering that exhibit cathodoluminescence (CL) at ultraviolet frequencies. The maximum CL brightness occurred at λ314–315 nm characteristic of the ⁶P_3 / 2 → ⁸S (λ = 314 nm) transition observed in Gd-doped, yttrium oxide powders. The radiative recombination takes place at the rare earth activator Gd³⁺ site embedded in the Y₂O_3−δ host; the optical transition resides within the band gap of the Y₂O_3−δ host and the transition observed is characteristic of atomic gadolinium. A combinatorial approach to sputtering was used to deposit a film of variable composition from 1 to 23 at.% Gd in Y₂O_3−δ in order to rapidly discern the composition node of optimal CL brightness. A simulation was created for the purpose of predicting the film combinatorial composition for binary and ternary alloys prior to sputtering experiments in order to facilitate our combinatorial thin film synthesis technique. The model prediction varied from the real experimental composition profile by only 2.2 at.% Gd ± 1.6 at.% proving the predictor as a useful aide to complement combinatorial thin film experiments. A film of composition Y_1.56Gd_0.44O_3.25 (8.3 at.% Gd) yielded the maximum CL brightness. CL brightness increased continuously up to the 8.3 at.% Gd composition due to the increased number of activators present in the host. Beyond this composition the brightness drastically decreased. The oxygen composition in the combinatorial film was strongly dependent on the Gd composition; films were sub-stoichiometric δ > 0 below 6 at.% Gd and was over-stoichiometric δ < 0 beyond this composition.     

Thermal nonlinear refraction in the dye-doped sol–gel xTiO2 · (100 − x)SiO2 system

The build-up time of the thermal lens effect induced by a Gaussian beam in the DO3-doped sol–gel system xTiO₂ · (100 − x)SiO₂ at different compositions, both in the liquid and gel phases has been measured in a Z-scan geometry. While the pure titania samples show a minimum of the thermal diffusivity, a maximum is found for x ≈ 30. The sol to gel transformation leads to an increase of the build-up times at all compositions.     

Effects of ZnO on piezoelectric properties of 0.01PMW–0.41PNN–0.35PT–0.23PZ ceramics

The microstructure and piezoelectric properties of the 0.01Pb(Mg_1/2W_1/2)O₃–0.41Pb(Ni_1/3Nb_2/3)O₃–0.35PbTiO₃–0.23PbZrO₃ + 0.1 and 0.3 wt.% Y₂O₃ + x ZnO ceramics were investigated. The crystal structure changed from psudocubic to tetragonal when ZnO added. The average grain size increased from 4 μm to 8 μm with the addition of ZnO by oxygen diffusion, even if the growth rate was low. When ZnO added until 0.5 wt.%, the , k_p and d₃₃ values of specimens were slightly increased regardless Y₂O₃ contents. The curie point of PMW–PNN–PT–PZ ceramics were increased from 162 °C to 232 °C, as increasing the ZnO contents. When ZnO added, the k_p of specimens slightly was increased regardless Y₂O₃ contents. The mechanical quality factors were abruptly decreased regardless Y₂O₃ contents, when ZnO added until 0.75 wt.%. The optimized piezoelectric properties were obtained; d₃₃ = 730 (pC/N), k_p = 60, Q_m = 50, and  = 4750, when PMW–PNN–PT–PZ + 0.3 wt.% Y₂O₃ + 0.5 wt.% ZnO sintered at 1200 °C for 1 h.     

Effect of ferroic domain pattern changes on the Raman spectra of some ferroic crystals

The influence of changes in the pattern of ferroic domain structure on the Raman spectra of β-LiNH₄SO₄ and (NH₄)₃H(SO₄)₂ single crystals were studied. It was shown that the Raman spectra of β-LiNH₄SO₄ passed from the ferroelastic phase differ from those of “as-grown” crystal and those of the crystal, which was in the paraelectric phase. Significant changes could be observed in the Raman bands related to triply degenerated ν₃ and ν₄ vibrations of the SO₄ tetrahedron. Detailed temperature studies of the Raman spectra of β-LiNH₄SO₄ close to the paraelectric–ferroelectric phase transition, exhibit anomaly of some internal vibrations of SO₄ in the temperature range where a regular large-scale structure is observed. Different types of evolution of the ferroelastic domain structure and temperature behaviour of the donor and acceptor vibrations were shown while heating and cooling the (NH₄)₃H(SO₄)₂ crystal. Different values of temperature hysteresis were found in temperature studies of the ferroelastic domain structure (ΔT_S  3–5 K) and in Raman spectra studies (ΔT_S  12 K). No changes were observed in the pattern of ferroelastic domain structure at the temperature T_II–III  265 K, at which C2/c → P2/n structural phase transition takes place. On the other hand, at T_III–IV  135 K additional domains with W′-type of domain wall orientation were found.     

Piezoelectric and dielectric properties of PZT–PZN–PMS ceramics prepared by molten salt synthesis method

Piezoelectric powders and ceramics with the composition of Pb_0.95Sr_0.05(Zr_0.52Ti_0.48)O₃–Pb(Zn_1/3Nb_2/3)O₃–Pb(Mn_1/3Sb_2/3)O₃ (PZT–PZN–PMS) were prepared by molten salt synthesis (MSS) and conventional mixed-oxide (CMO) methods, respectively. The influence of synthesis process on the properties of powders and ceramics were investigated in detail. The results show that the MSS method significantly improved the sinterability of PZT–PZN–PMS ceramics, resulting in an improvement of dielectric and piezoelectric properties compared to the CMO method. The optimum values of MSS samples are as follows: _r = 1773; tan δ = 0.0040; T_c = 280 °C; d₃₃ = 455 pC/N; k_p = 0.70; Q_m = 888; E_c = 10.3 kV/cm; and P_r = 28.2 μC/cm², at calcination of 800 °C and sintering of 1120 °C temperature.     

Synthesis and the luminescent properties of europium-activated Ca2SnO4 phosphors

The synthesis and photoluminescent (PL) properties of calcium stannate crystals doped with europium grown by mechanically activated in a high energy vibro-mill have been investigated. The characteristics of Ca₂SnO₄:Eu³⁺ phosphors were found to depend on the amounts of europium ions. The XRD profiles revealed that the system, (Ca_1−xEu_x)₂SnO₄, could form stable solid solutions in the composition range of x = 0–7% after being calcined at 1200 °C. The calcined powders emit bright red luminescence centered at 618 nm due to ⁵D₀ → ⁷F₂ electric dipole transition. Both XRD data and the emission ratio of (⁵D₀ → ⁷F₂)/(⁵D₀ → ⁷F₁) reveal that the site symmetry of Eu³⁺ ions decreases with increasing doping concentration. The maximum PL intensity has been obtained for 7 mol% concentration of Eu³⁺ in Ca₂SnO₄.     

Synthesis, structure refinement and characterization of tetrahydrated acid gadolinium diphosphate HGdP2O7·4H2O

Synthesis and single crystal structure are reported for a new gadolinium acid diphosphate tetrahydrate HGdP₂O₇·4H₂O. This salt crystallizes in the monoclinic system, space group P2₁/n, with the following unit-cell parameters: a = 6.6137(2) Å, b = 11.4954(4) Å, c = 11.377(4) Å, β = 87.53(2)° and Z = 4. Its crystal structure was refined to R = 0.0333 using 1783 reflections. The corresponding atomic arrangement can be described as an alternation of corrugated layers of monohydrogendiphosphate groups and GdO₈ polyhedra parallel to the () plane. The cohesion between the different diphosphoric groups is provided by strong hydrogen bonding involving the W4 water molecule.

IR and Raman spectra of HGdP₂O₇·4H₂O confirm the existence of the characteristic bands of diphosphate group in 980–700 cm⁻¹ area. The IR spectrum reveals also the characteristic bands of water molecules vibration (3600–3230 cm⁻¹) and acidic hydrogen ones (2340 cm⁻¹). TG and DTA investigations show that the dehydration of this salt occurs between 79 and 900 °C. It decomposes after dehydration into an amorphous phase. Gadolinium diphosphate Gd₄(P₂O₇)₃ was obtained by heating HGdP₂O₇·4H₂O in a static air furnace at 850 °C for 48 h.     

ZBAS对BaAl2Si2O8结构与微波介电性能的影响

采用固相反应工艺, 按化学计量百分比BaAl₂Si₂O₈-x(ZnO-Al₂O₃-SiO₂-B₂O₃)(x=0, 1%, 2%, 3%, 4%)制备样品, 研究了不同含量ZnO-Al₂O₃-SiO₂-B₂O₃(ZBAS)玻璃相对BaO-Al₂O₃-SiO₂系介电材料显微结构及微波介电性能的影响。结果表明: 添加ZBAS玻璃相可以适当降低烧结温度, 促进六方钡长石转变为单斜钡长石。当x≥3%时, 六方钡长石可以完全转变为单斜钡长石。随着ZBAS玻璃相含量的增多, 样品的密度、介电常数(ε_r)、品质因数(Q×f)和谐振频率温度系数(τ_f )增大。在x=3%, 烧结温度为1360℃时, 可以获得综合性能相对较好的单斜钡长石, 其介电性能: ε_r=6.72, Q×f=28058 GHz, τ_f =-29.79×10^-6℃^-1。     

Optical and electrical properties of p-type AgInSnxS2−x (x = 0–0.04) thin films prepared by spray pyrolysis

AgInSn_xS_2−x (x = 0–0.2) polycrystalline thin films were prepared by the spray pyrolysis technique. The samples were deposited on glass substrates at temperatures of 375 and 400 °C from alcoholic solutions comprising silver acetate, indium chloride, thiourea and tin chloride. All deposited films crystallized in the chalcopyrite structure of AgInS₂. A p-type conductivity was detected in the Sn-doped samples deposited at 375 °C, otherwise they are n-type. The optical properties of AgInSn_xS_2−x (x < 0.2) resemble those of chalcopyrite AgInS₂. Low-temperature PL measurements revealed that Sn occupying an S-site could be the responsible defect for the p-type conductivity observed in AgInSn_xS_2−x (x < 2) thin films.     

Nanocrystallization of SrBi2Nb2O9 from glasses in the system Li2B4O7---SrO---Bi2O3---Nb2O5

Transparent glasses in the system (100−x)Li₂B₄O₇–x(SrO---Bi₂O₃---Nb₂O₅) (10≤x≤60) (in molar ratio) were fabricated by a conventional melt-quenching technique. Amorphous and glassy characteristics of the as-quenched samples were established via X-ray powder diffraction (XRD) and differential thermal analyses (DTA) respectively. Glass–ceramics embedded with strontium bismuth niobate, SrBi₂Nb₂O₉ (SBN) nanocrystals were produced by heat-treating the as-quenched glasses at temperatures higher than 500 °C. Perovskite SBN phase formation through an intermediate fluorite phase in the glass matrix was confirmed by XRD and transmission electron microscopy (TEM). Infrared and Raman spectroscopic studies corroborate the observation of fluorite phase formation. The dielectric constant (_r) and the loss factor (D) for the lithium borate, Li₂B₄O₇ (LBO) glass comprising randomly oriented SBN nanocrystals were determined and compared with those predicted based on the various dielectric mixture rule formalism. The dielectric constant was found to increase with increasing SBN content in LBO glass matrix.