Synthesis and characterization of Li3V(2 − 2x/3)Mgx(PO4)3/C cathode material for lithium-ion batteries

Li₃V_{(2 − 2x/3)}Mg_x(PO₄)₃/C (x = 0, 0.15, 0.30, 0.45) composites have been synthesized by the sol-gel assisted solid state method, using adipic acid C₆H₁₀O₄ (hexanedioic acid) as carbon source. The particle size of the composites is ∼1 μm. During the pyrolysis process, Li₃V_{(2 − 2x/3)}Mg_x(PO₄)₃/C network structure is formed. The effect of Mg²⁺ doped on the electrochemical properties of Li₃V₂(PO₄)₃/C positive materials has been studied. Li₃V_1.8Mg_0.30(PO₄)₃/C as the cathode materials of Li-ion batteries, the retention rate of discharge capacity is 91.4% (1 C) after 100 cycles. Compared with Li₃V₂(PO₄)₃/C, Li₃V_{(2 − 2x/3)}Mg_x(PO₄)₃/C composites have shown enhanced capacity and retention rate capability. The long-term cycles and ex situ XRD tests disclose that Li₃V_1.8Mg_0.30(PO₄)₃ exhibits higher structural stability than the undoped system.     

Synthesis and performance of Li3(V1−xMgx)2(PO4)3 cathode materials

In order to search for cathode materials with better performance, Li₃(V_1−xMg_x)₂(PO₄)₃ (0, 0.04, 0.07, 0.10 and 0.13) is prepared via a carbothermal reduction (CTR) process with LiOH·H₂O, V₂O₅, Mg(CH₃COO)₂·4H₂O, NH₄H₂PO₄, and sucrose as raw materials and investigated by X-ray diffraction (XRD), scanning electron microscopic (SEM) and electrochemical impedance spectrum (EIS). XRD shows that Li₃(V_1−xMg_x)₂(PO₄)₃ (x = 0.04, 0.07, 0.10 and 0.13) has the same monoclinic structure as undoped Li₃V₂(PO₄)₃ while the particle size of Li₃(V_1−xMg_x)₂(PO₄)₃ is smaller than that of Li₃V₂(PO₄)₃ according to SEM images. EIS reveals that the charge transfer resistance of as-prepared materials is reduced and its reversibility is enhanced proved by the cyclic votammograms. The Mg²⁺-doped Li₃V₂(PO₄)₃ has a better high rate discharge performance. At a discharge rate of 20 C, the discharge capacity of Li₃(V_0.9Mg_0.1)₂(PO₄)₃ is 107 mAh g⁻¹ and the capacity retention is 98% after 80 cycles. Li₃(V_0.9Mg_0.1)₂(PO₄)₃//graphite full cells (085580-type) have good discharge performance and the modified cathode material has very good compatibility with graphite.     

Synthesis of plate-like Li3V2(PO4)3/C as a cathode material for Li-ion batteries

Plate-like Li₃V₂(PO₄)₃/C composite is synthesized via a solution route followed by solid-state reaction. The Li₃V₂(PO₄)₃/C plates are 40-100 nm in thicknesses and 2-10 μm in lengths. TEM images show that a uniform carbon layer with a thickness of 5.3 nm presents on the surfaces of Li₃V₂(PO₄)₃ plates. The apparent Li-ion diffusion coefficient of the plate-like Li₃V₂(PO₄)₃/C is calculated to be 2.7 × 10⁻⁸ cm² s⁻¹. At a charge-discharge rate of 3 C, the plate-like Li₃V₂(PO₄)₃/C exhibits an initial discharge capacity of 125.2 and 133.1 mAh g⁻¹ in the voltage ranges of 3.0-4.3 and 3.0-4.8 V, respectively. After 500 cycles, the electrodes still can deliver a discharge capacity of 111.8 and 97.8 mAh g⁻¹ correspondingly, showing a good cycling stability.     

Synthesis and electrochemical performances of Li3V2(PO4)3/(Ag + C) composite cathode

Li₃V₂(PO₄)₃, Li₃V₂(PO₄)₃/C and Li₃V₂(PO₄)₃/(Ag + C) composites as cathodes for Li ion batteries are synthesized by carbon-thermal reduction (CTR) method and chemical plating reactions. The microstructure and morphology of the compounds are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The Li₃V₂(PO₄)₃/(Ag + C) particles are 0.5-1 μm in diameters. As compared to Li₃V₂(PO₄)₃, Li₃V₂(PO₄)₃/C, the Li₃V₂(PO₄)₃/(Ag + C) composite cathode exhibits high discharge capacity, good cycle performance (140.5 mAh g⁻¹ at 50th cycle at 1 C, 97.3% of initial discharge capacity) and rate behavior (120.5 mAh g⁻¹ for initial discharge at 5 C) for the fully delithiated (3.0-4.8 V) state. Electrochemical impedance spectroscopy (EIS) measurements show that the carbon and silver co-modification decreases the charge transfer resistance of Li₃V₂(PO₄)₃/(Ag + C) cathode, and improves the conductivity and boosts the electrochemical performance of the electrode.     

High-rate cathodes based on Li3V2(PO4)3 nanobelts prepared via surfactant-assisted fabrication

In this work, we have synthesized monoclinic Li₃V₂(PO₄)₃ nanobelts via a single-step, solid-state reaction process in a molten hydrocarbon. The as-prepared Li₃V₂(PO₄)₃ nanoparticles have a unique nanobelt shape and are ∼50-nm thick. When cycled in a voltage range between 3.0 V and 4.3 V at a 1C rate, these unique Li₃V₂(PO₄)₃ nanobelts demonstrate a specific discharge capacity of 131 mAh g⁻¹ (which is close to the theoretical capacity of 132 mAh g⁻¹) and stable cycling characteristics.     

Li3V2(PO4)3 cathode material synthesized by chemical reduction and lithiation method

The monoclinic-type Li₃V₂(PO₄)₃ cathode material was synthesized via calcining amorphous Li₃V₂(PO₄)₃ obtained by chemical reduction and lithiation of V₂O₅ using oxalic acid as reducer and lithium carbonate as lithium source in alcohol solution. The amorphous Li₃V₂(PO₄)₃ precursor was characterized by using TG–DSC and XPS. The results showed that the V⁵⁺ was reduced to V³⁺ by oxalic acid at ambient temperature and pressure. The prepared Li₃V₂(PO₄)₃ was characterized by XRD and SEM. The results indicated the Li₃V₂(PO₄)₃ powder had good crystallinity and mesoporous morphology with an average diameter of about 30 nm. The pure Li₃V₂(PO₄)₃ exhibits a stable discharge capacity of 130.08 mAh g⁻¹ at 0.1 C (14 mA g⁻¹).     

Characteristics of Li3V2(PO4)3/C powders prepared by ultrasonic spray pyrolysis

Li₃V₂(PO₄)₃ and Li₃V₂(PO₄)₃/C powders are prepared by ultrasonic spray pyrolysis from spray solutions with and without sucrose. The precursor powders have a spherical shape and the crystal structure of V₂O₃ irrespective of the concentration of sucrose in the spray solution. The powders post-treated at 700 °C have the pure crystal structure of the Li₃V₂(PO₄)₃ phase irrespective of the concentration of sucrose in the spray solution. The Li₃V₂(PO₄)₃ powders prepared from the spray solution without sucrose have a non-spherical shape and hard aggregation. However, the Li₃V₂(PO₄)₃/C powders prepared from the spray solution with sucrose have a spherical shape and non-aggregation characteristics. The Li₃V₂(PO₄)₃ powders prepared from the spray solution without sucrose have a low initial discharge capacity of 122 mAh g⁻¹. However, the Li₃V₂(PO₄)₃/C powders prepared from the spray solutions with 0.1, 0.3, and 0.5 M sucrose have initial discharge capacities of 141, 130, and 138 mAh g⁻¹, respectively. After 25 cycles, the discharge capacities of the powders formed from the spray solutions with and without 0.1 M sucrose are 70% and 71% of the initial discharge capacities, respectively.     

Synthesis and improved electrochemical performances of porous Li3V2(PO4)3/C spheres as cathode material for lithium-ion batteries

Spherical Li₃V₂(PO₄)₃/C composites are synthesized by a soft chemistry route using hydrazine hydrate as the spheroidizing medium. The electrochemical properties of the materials are investigated by galvanostatic charge-discharge tests, cyclic voltammograms and electrochemical impedance spectrum. The porous Li₃V₂(PO₄)₃/C spheres exhibit better electrochemical performances than the solid ones. The spherical porous Li₃V₂(PO₄)₃/C electrode shows a high discharge capacity of 129.1 and 125.6 mAh g⁻¹ between 3.0 and 4.3 V, and 183.8 and 160.9 mAh g⁻¹ between 3.0 and 4.8 V at 0.2 and 1 C, respectively. Even at a charge-discharge rate of 15 C, this material can still deliver a discharge capacity of 100.5 and 121.5 mAh g⁻¹ in the potential regions of 3.0-4.3 V and 3.0-4.8 V, respectively. The excellent electrochemical performance can be attributed to the porous structure, which can make the lithium ion diffusion and electron transfer more easily across the Li₃V₂(PO₄)₃/electrolyte interfaces, thus resulting in enhanced electrode reaction kinetics and improved electrochemical performance.     

Temperature-controlled microwave solid-state synthesis of Li3V2(PO4)3 as cathode materials for lithium batteries

Monoclinic Li₃V₂(PO₄)₃ can be rapidly synthesized at 750 °C for 5 min (MW5m) by using temperature-controlled microwave solid-state synthesis method (TCMS). The carbon-free sample MW5m presents well electrochemical properties. In the cut-off voltage 3.0-4.3, MW5m presents a charge capacity 132 mAh g⁻¹, almost equivalent to the reversible cycling of two lithium ions per Li₃V₂(PO₄)₃ formula unit (133 mAh g⁻¹), and discharge capacity 126.4 mAh g⁻¹. In the cut-off voltage 3.0-4.8 V, MW5m shows an initial discharge capacity of 183.4 mAh g⁻¹, near to the theoretical discharge capacity. In the cycle performance, the capacity fade of Li₃V₂(PO₄)₃ is dependent on the cut-off voltage and the preparation method.     

A fast synthesis of Li3V2(PO4)3 crystals via glass-ceramic processing and their battery performance

A synthesis of Li₃V₂(PO₄)₃ being a potential cathode material for lithium ion batteries was attempted via a glass-ceramic processing. A glass with the composition of 37.5Li₂O-25V₂O₅-37.5P₂O₅ (mol%) was prepared by a melt-quenching method and precursor glass powders were crystallized with/without 10 wt% glucose in N₂ or 7%H₂/Ar atmosphere. It was found that heat treatments with glucose at 700 °C in 7%H₂/Ar can produce well-crystallized Li₃V₂(PO₄)₃ in the short time of 30 min. The battery performance measurements revealed that the precursor glass shows the discharge capacity of 14 mAh g⁻¹ at the rate of 1 μA cm⁻² and the glass-ceramics with Li₃V₂(PO₄)₃ prepared with glucose at 700 °C in 7%H₂/Ar show the capacities of 117-126 mAh g⁻¹ (∼96% of the theoretical capacity) which are independent of heat treatment time. The present study proposes that the glass-ceramic processing is a fast synthesizing route for Li₃V₂(PO₄)₃ crystals.     

Novel synthesis of LiFePO4-Li3V2(PO4)3 composite cathode material by aqueous precipitation and lithiation

LiFePO₄-Li₃V₂(PO₄)₃ composite cathode material is synthesized by aqueous precipitation of FeVO₄·xH₂O from Fe(NO₃)₃ and NH₄VO₃, following chemical reduction and lithiation with oxalic acid as the reducer and carbon source. Samples are characterized by XRD, SEM and TEM. XRD pattern of the compound synthesized at 700 °C indicates olivine-type LiFePO₄ and monoclinic Li₃V₂(PO₄)₃ are co-existed. TEM image exhibits that LiFePO₄-Li₃V₂(PO₄)₃ particles are encapsulated with a carbon shell 5-10 nm in thickness. The LiFePO₄-Li₃V₂(PO₄)₃ compound cathode shows good electrochemical performance, and its discharge capacity is about 139.1 at 0.1 C, 135.5 at 1 C and 116 mA h g⁻¹ at 3 C after 30 cycles.     

Highly promoted electrochemical performance of 5 V LiCoPO4 cathode material by addition of vanadium

Li_1+0.5xCo_1−xV_x(PO₄)_1+0.5x/C (x = 0, 0.05, 0.10) composites with ordered olivine structure have been synthesized for use as cathode material in lithium ion batteries. The morphology and microstructure are characterized by scanning electron microscope, transmission electron microscopy and X-ray diffraction. The electrochemical test results show that addition of vanadium into LiCoPO₄ remarkably improves its charge and discharge behavior. Li_1.025Co_0.95V_0.05(PO₄)_1.025/C electrode gives its initial discharge capacity of 134.8 mAh g⁻¹ at 0.1 C current rate, against 112.2 mAh g⁻¹ for the pristine LiCoPO₄/C, and exhibits much better cyclic stability than the latter. In particular, vanadium doping leads to an enhancement of the discharge voltage plateau for about 70 mV.     

Electrochemical behavior of Li3−xM′xV2−yM″y(PO4)3 (M′ = K, M″ = Sc, Mg + Ti)/C composite cathode material for lithium-ion batteries

Composites of monoclinic Li_3−xM′_xV_2−yM″_2y(PO₄)₃ (M′ = K, M″ = Sc, Mg + Ti) with carbon were synthesized by solid-state reaction using oxalic acid or 6% H₂/Ar gas mixture as reducing agents at sintering temperature of 850 °C. The samples were characterized by X-ray diffraction (XRD), voltammetry and electrochemical galvanostatic cycling. The capacity of Li₃V₂(PO₄)₃ synthesized using hydrogen as the reducing agent was 127 mA h g⁻¹ and decreased to 120 mA h g⁻¹ after 20 charge-discharge cycles. The substitution of lithium and vanadium for other ions did not result in the improvement of the electrochemical characteristics of the samples.     

Li1.2Zr1.9Ca0.1(PO4)3, a room-temperature Li-ion solid electrolyte

Substitution of 5% of Zr by Ca in LiZr₂(PO₄)₃ transforms the structure to that of rhombohedral NASICON to give a room-temperature bulk Li-ion conductivity σ_Li ≈ 1.2 × 10⁻⁴ S cm⁻¹, which is comparable to that of Li_1.3Ti_1.7Al_0.3(PO₄)₃ now being used as a solid Li-ion separator in test cells of novel Li-ion batteries.     

Improved electrochemical performances of 9LiFePO4·Li3V2(PO4)/C composite prepared by a simple solid-state method

9LiFePO₄·Li₃V₂(PO₄)₃/C is synthesized via a carbon thermal reaction using petroleum coke as both reduction agent and carbon source. The as-prepared material is not a simple mixture of LiFePO₄ (LFP) and Li₃V₂(PO₄)₃ (LVP), but a composite possessing two phases: one is V-doped LFP and the other is Fe-doped LVP. The typical structure enhances the electrical conductivity of the composite and improves the electrochemical performances. The first discharge capacity of 9LFP·LVP/C in 18650 type cells is 168 mAh g⁻¹ at 1 C (1 C_9LFP·LVP/C = 166 mA g⁻¹), and exhibits high reversible discharge capacity of 125 mAh g⁻¹ at 10 C even after 150 cycles. At the temperature of −20 °C, the reversible capacity of 9LFP·LVP/C can maintain 75% of that at room temperature.     

Effects of fluorine-substitution on the electrochemical behavior of LiFePO4/C cathode materials

The effects of fluorine substitution on the electrochemical properties of LiFePO₄/C cathode materials were studied. Samples with stoichiometric proportion of LiFe(PO₄)_1−xF_3x/C (x = 0.025, 0.05, 0.1) were prepared by adding LiF in the starting materials of LiFePO₄/C. XRD and XPS analyses indicate that LiF was completely introduced into bulk LiFePO₄ structure in LiFe(PO₄)_1−xF_3x/C (x = 0.025, 0.05) samples, while there was still some excess of LiF in LiFe(PO₄)_0.9F_0.3/C sample. The results of electrochemical measurement show that F-substitution can improve the rate capability of these cathode materials. The LiFe(PO₄)_0.9F_0.3/C sample showed the best high rate performance. Its discharge capacity at 10 C rate was 110 mAh g⁻¹ with a discharge voltage plateau of 3.31–3.0 V versus Li/Li⁺. The LiFe(PO₄)_0.9F_0.3/C sample also showed obviously better cycling life at high temperature than the other samples.     

High-throughput studies of Li1−xMgx/2FePO4 and LiFe1−yMgyPO4 and the effect of carbon coating

A two-dimensional sample array synthesis has been used to screen carbon-coated Li_(1−x)Mg_x/2FePO₄ and LiFe_(1−y)Mg_yPO₄ powders as potential positive electrode materials in lithium ion batteries with respect to x, y and carbon content. The synthesis route, using sucrose as a carbon source as well as a viscosity-enhancing additive, allowed introduction of the Mg dopant from solution into the sol–gel pyrolysis precursor. High-throughput XRD and cyclic voltammetry confirmed the formation of the olivine phase and percolation of the electronic conduction path at sucrose to phosphate ratios between 0.15 and 0.20. Measurements of the charge passed per discharge cycle showed that the capacity deteriorated on increasing magnesium in Li_(1−x)Mg_x/2FePO₄, but improved with increasing magnesium in LiFe_(1−y) Mg_yPO₄, especially at high scan rates. Rietveld-refined XRD results on samples of LiFe_(1−y)Mg_yPO₄ prepared by a solid-state route showed a single phase up to y = 0.1 according to progressive increases in unit cell volume with increases in y. Carbon-free samples of the same materials showed conductivity increases from 10⁻¹⁰ to 10⁻⁸ S cm⁻¹ and a decrease of activation energy from 0.62 to 0.51 eV. Galvanostatic cycling showed near theoretical capacity for y = 0.1 compared with only 80% capacity for undoped material under the same conditions.     

Li3V2(PO4)3/C composite as an intercalation-type anode material for lithium-ion batteries

The carbon coated monoclinic Li₃V₂(PO₄)₃ (LVP/C) powder is successfully synthesized by a carbothermal reduction method using crystal sugar as the carbon source. Its structure and physicochemical properties are investigated using X-ray diffraction (XRD), scanning electron microscopy, high-resolution transmission electron microscopy and electrochemical methods. The LVP/C electrode exhibits stable reversible capacities of 203 and 102 mAh g⁻¹ in the potential ranges of 3.0-0.0 V and 3.0-1.0 V versus Li⁺/Li, respectively. It is identified that the insertion/extraction of Li⁺ undergoes a series of two-phase transition processes between 3.0 and 1.6 V and a single phase process between 1.6 and 0.0 V. The ex situ XRD patterns of the electrodes at various lithiated states indicate that the monoclinic structure can still be retained during charge-discharge process and the insertion/deinsertion of lithium ions occur reversibly, which provides an excellent cycling stability with high energy efficiency.     

Enhanced electrochemical properties of Li(Ni0.4Co0.3Mn0.3)O2 cathode by surface modification using Li3PO4-based materials

The surface of a commercial Li[Ni_0.4Co_0.3Mn_0.3]O₂ cathode is modified using Li₃PO₄-based coating materials. The electrochemical properties of the coated materials are investigated as a function of the pH value of the coating solution and the composition of coating materials. The Li₃PO₄ coating solution with pH 2 is found to be favorable for the formation of stable coating layers having enhanced electrochemical properties. The Li₃PO₄, Li_1.5PO₄, and PO₄ coating layers are formed as amorphous phases. However, the Li_3−xNi_x/2PO₄ coating layers are composed of small particles with a crystalline phase covered with an amorphous phase. Li₃PO₄ and Li_1.5PO₄ coatings considerably enhance the rate capability of the Li[Ni_0.4Co_0.3Mn_0.3]O₂ electrode. In contrast, the Li_3−xNi_x/2PO₄ coating material, which contained Ni, has an inferior rate capability compared to the Li_xPO₄ series (x = 1.5 and 3), although the LiNiPO₄-coated electrode shows a better rate capability than a pristine one. Li₃PO₄-based coating materials are effective at enhancing the cyclic performance of the electrode in the voltage range of 3.0-4.8 V. DSC analysis also confirms the improved thermal stability attained by coating the cathode with Li₃PO₄-based materials.     

Synthesis and performance of carbon-coated Li3V2(PO4)3 cathode materials by a low temperature solid-state reaction

The carbon-coated monoclinic Li₃V₂(PO₄)₃ (LVP) cathode materials can be synthesized by a low temperature solid-state reaction route. The influences of different heat treatments on the LVP have been investigated using X-ray diffraction (XRD), scanning electron microscopy (SEM) and electrochemical methods. In the range of 3.0-4.3 V, both LVP/C electrodes present good rate capability and excellent cyclic performance. It is found that the sample (LVP1/C) prepared by the two-step heat treatment with pre-sintering at 350 °C delivers the initial discharge capacity of 99.8 mAh g⁻¹ at 10 C charge-discharge rate and still retains 95.8 mAh g⁻¹ after 300 cycles. For the sample (LVP2/C) synthesized by the one-step heat treatment, 95.9 and 90.0 mAh g⁻¹ are obtained in the 1st and 300th cycles at 10 C rate, respectively. Our results based on the XRD patterns and the SEM images suggest that the good rate capability and cyclic performance may be owing to the pure phases, small particles, large specific surface areas and residual carbon. In the range of 3.0-4.8 V, compared with the LVP2/C, the LVP1/C also exhibits better performance.