Improved stability quasi-solid-state dye-sensitized solar cell based on polyether framework gel electrolytes

We report three improved stability dye-sensitized TiO₂ photoelectrochemical cells using quasi-solid polymer electrolytes containing poly(propylene oxide) (PPO), poly(ethylene oxide) (PEO) or poly(ethylene oxide)-block-poly(propylene oxide)-block-poly(ethylene oxide) (P₁₂₃). After introducing the polyether into the liquid electrolyte, the parameters of these quasi-solid-state solar cells are 90% comparable to that of the liquid photochemical cells, although the conductivities of these polyether framework gel electrolytes are lower than that of the bulk liquid electrolyte. The different morphologies of dried liquid electrolyte and the polyether gel electrolytes are characterized with an atomic force microscope (AFM) to explain the better stability exhibited by the polyether gel electrolytes.     

Electrolyte infiltration in phosphazene-based dye-sensitized solar cells

We report here a study of phosphazene polymer and oligomer electrolyte infiltration into high surface area titanium dioxide electrodes and its effect on the performance of dye-sensitized solar cells. The effects of different cell assembly procedures on the electrochemical properties are examined, as well as the infiltration of electrolytes based on poly[bis(2-(2-methoxyethoxy)ethoxy)phosphazene] (MEEP), hexakis(2-(2-methoxyethoxy)ethoxy)cyclotriphosphazene (MEE trimer), and a linear short chain analogue into conventional titanium dioxide electrode mesoporous (nanosphere) films, microcolumns and nanowires. The effects of temperature, co-solvents, and the order of addition of the electroactive components are found to affect both the conductivity of the electrolytes and the electrochemical performance of the cells. Cross-sectional scanning electron microscopy (SEM) imaging is employed to examine the degree of electrolyte infiltration into the nanostructured electrodes as a function of filling conditions. Using these techniques, conditions are identified for achieving a high degree of pore filling by the three electrolyte systems. Increased power conversion efficiency is obtained when iodine is introduced after the heating and evacuation procedures required for maximum infiltration.     

Nanocomposite gel electrolyte with large enhanced charge transport properties of an I3/I redox couple for quasi-solid-state dye-sensitized solar cells

TiO₂ nanoparticles was introduced into quasi-solid-state Poly(vinylidenefluoride-co-hexafluoropropylene) (P(VDF-HFP)) based gel electrolyte to form nanocomposite gel electrolyte for quasi-solid-state dye-sensitized solar cells. The steady-state voltammograms revealed that the diffusion performance of the triiodide and iodide in the quasi-solid-state P(VDF-HFP) based gel electrolyte was greatly enhanced after the addition of TiO₂ nanoparticles. Especially, the apparent diffusion coefficient of I₃⁻ increased from 0.76×10⁻¹⁰ m²/s to 4.42×10⁻¹⁰ m²/s, reached the level of the liquid electrolyte (4.04×10⁻¹⁰ m²/s). By introducing TiO₂ nanoparticles, the photoelectric conversion efficiency of the gel based device increased from 5.72% to 7.18%, which reached the level of the liquid electrolytes based device (7.01%). The electrical impedance spectrum revealed that the addition of TiO₂ nanoparticles could reduce the charge recombination at the interface of dyed TiO₂ electrode/electrolyte. The results of the accelerated aging tests showed that the nano-TiO₂ composite gel electrolytes based devices could maintain 90% of their initial value after heating at 60 °C for 1000 h, which indicated that they had better thermostability than the corresponding normal gel electrolyte based devices and liquid electrolyte based devices.     

A high-performance counter electrode based on poly(3,4-alkylenedioxythiophene) for dye-sensitized solar cells

A poly(3,3-diethyl-3,4-dihydro-2H-thieno-[3,4-b][1,4]dioxepine) (PProDOT-Et₂) counter electrode prepared by electrochemical polymerization on a fluorine-doped tin oxide (FTO) glass substrate was incorporated in a platinum-free dye-sensitized solar cell (DSSC). The surface roughness and I⁻/I₃⁻ redox reaction behaviors based on PProDOT-Et₂, poly(3,4-propylenedioxythiophene) (PProDOT), poly(3,4-ethylenedioxythiophene) (PEDOT), and sputtered-Pt electrodes were characterized, and their performances as counter electrodes in DSSCs were compared. Cells fabricated with a PProDOT-Et₂ counter electrode showed a higher conversion efficiency of 7.88% compared to cells fabricated with PEDOT (3.93%), PProDOT (7.08%), and sputtered-Pt (7.77%) electrodes. This enhancement was attributed to increases in the effective surface area and good catalytic properties for I₃⁻ reduction. In terms of the film thickness effect, the fill factor was strongly dependent on the deposition charge capacity of the PProDOT-Et₂ layer, but the aggregation of PProDOT-Et₂ in thicker layers (>80 mC cm⁻²) resulted in decreases in J_SC and the cell conversion efficiency. The charge transfer resistances (R_ct1) of the PProDOT-Et₂ counter electrodes had the lowest value of ∼18 Ω at a deposition charge capacity of 40 mC cm⁻². These results indicate that films with high conductivity, high active surface area, and good catalytic properties for I₃⁻ reduction can potentially be used as the counter electrode in a high-performance DSSC.     

Influence of polymer concentration and dyes on photovoltaic performance of dye-sensitized solar cell with P(VdF-HFP)-based gel polymer electrolyte

A series of gel polymer electrolytes (GPEs) is synthesized using Poly(vinylidenefluoride-hexafluoropropylene) P(VdF-HFP) as the host matrix and propylene carbonate (PC)–diethyl carbonate (DEC) as plasticizers to fabricate dye-sensitized solar cells. Equal amounts of PC and DEC are used to comprehend high dielectric constant and low viscosity of the electrolyte. The as-prepared GPEs are characterized by XRD, FTIR and SEM. Their thermal properties and ionic conductivities are investigated by TGA/DSC analyses and AC impedance measurements, respectively. The optimized gel polymer electrolyte gives a maximum ionic conductivity of 5.25 × 10⁻³ S cm⁻¹ at room temperature. The formation of porous structure in the electrolyte film supports the entrapment of large volumes of liquid electrolyte inside its cavities. The role of N3 and N719 dyes are also investigated for better photovoltaic performance of DSSC. The overall light-to-electrical-energy conversion efficiencies of 3.95% and 4.41% are obtained for N3 and N719 dyes, respectively, under 100 mW cm⁻² irradiation, which are comparable to those obtained from the corresponding liquid electrolyte cell.     

Solid-state photoelectrochemical device based on poly(3-hexylthiophene) and an ion conducting polymer electrolyte, amorphous poly(ethylene oxide) complexed with I3/I redox couple

The photoelectrochemical properties of a solid-state photoelectrochemical cell (PEC) based on poly(3-hexylthiophene), P3HT, and an ion-conducting polymer electrolyte, amorphous poly(ethylene oxide), POMOE, complexed with I₃⁻/I⁻ redox couple has been constructed and studied. The current–voltage characteristics in the dark and under white light illumination, transient photocurrent and photovoltage studies, photocurrent action spectra for front and back side illuminations and an open-circuit voltage and short-circuit current dependence on light intensity have been studied. An open-circuit voltage of 130 mV and a short-circuit current of 0.47 μA cm⁻² were obtained at light intensity of 100 mW/cm². IPCE% of 0.024% for front side illumination (ITO/PEDOT) and IPCE% of 0.003% for backside illumination (ITO/P3HT) were obtained.     

Quasi-solid-state dye-sensitized solar cells based on a sol–gel organic–inorganic composite electrolyte containing an organic iodide salt

An organic–inorganic composite gel electrolyte based on TiO₂ gel, γ-butyrolactone (γ-BL) and N-methyl pyridine iodide was prepared by the sol–gel method. This gel electrolyte shows high ambient ionic conductivity of 7.63 mS cm⁻¹, which is close to the data of liquid electrolyte with the same organic iodide salt and γ-butyrolactone. Based on the gel electrolyte, a quasi-solid-state dye-sensitized solar cell was fabricated and the highest overall energy conversion efficiency of light-to-electricity of 3.06% was achieved under irradiation of 60 mW cm⁻².     

Influence of electrolyte on the photovoltaic performance of a dye-sensitized TiO2 solar cell based on a Ru(II) terpyridyl complex photosensitizer

We have investigated the influence of electrolyte composition on the photovoltaic performance of a dye-sensitized nanocrystalline TiO₂ solar cell (DSSC) based on a Ru(II) terpyridyl complex photosensitizer (the black dye). We have also spectroscopically investigated the interaction between the electrolyte components and the adsorbed dye. The absorption peaks attributed to the metal-to-ligand charge transfer transitions of the black dye in solution and adsorbed on a TiO₂ film, were red-shifted in the presence of Li cations, which led to an expansion of the spectral response of the solar cell toward the near-IR region. The photovoltaic performance of the DSSC based on the black dye depended remarkably on the electrolyte composition. We developed a novel efficient organic liquid electrolyte containing an imidazolium iodide such as 1,2-dimethyl-3-n-propylimidazolium iodide or 1-ethyl-3-methylimidazolium iodide (EMImI) for a DSSC based on the black dye. A high solar energy-to-electricity conversion efficiency of 9.2% (J_sc=19.0 mA cm⁻², V_oc=0.67 V, and FF=0.72) was attained under AM 1.5 irradiation (100 mW cm⁻²) using a novel electrolyte consisting of 1.5 M EMImI, 0.05 M iodine, and acetonitrile as a solvent with an antireflection film.     

In search of better energy performance in the Portuguese buildings—The case of the Portuguese regulation

The Energy Performance of Buildings Directive (EPBD) is an important European policy tool to improve energy performance of buildings and has been applied in 27 countries with specific adjustments.     

Enhancing thermal conductivity of palmitic acid based phase change materials with carbon nanotubes as fillers

Multi-walled carbon nanotubes (CNTs) as produced are usually entangled and not ready to be dispersed into organic matrix. CNTs were treated by mechano-chemical reaction with ball milling the mixture of potassium hydroxide and the pristine CNTs. Hydroxide radical functional groups have been introduced on the CNT surfaces, which enabled to make stable and homogeneous CNT composites. Treated CNTs were successfully dispersed into the palmitic acid matrix without any surfactant. Transient short-hot-wire apparatus was used to measure the thermal conductivities of these nanotube composites. Nanotube composites have substantially higher thermal conductivities than the base palmitic acid matrix, with the enhancement increasing with the mass fraction of CNTs in both liquid state and solid state. The enhancements of the thermal conductivity are about 30% higher than the reported corresponding values for palmitic acid based phase change nanocomposites containing 1 wt% CNTs treated by concentrated acid mixture.     

Properties of the lithium and graphite-lithium anodes in N-methyl-N-propylpyrrolidinium bis(trifluoromethanesulfonyl)imide

The ternary [Li⁺]_0.09[MePrPyr⁺]_0.41[NTf₂⁻]_0.50 room temperature ionic liquid was obtained by dissolution of solid lithium bis(trifluoromethanesulfonyl)imide (LiNTf₂) in liquid N-methyl-N-propylpyrrolidinium bis(trifluoromethanesulfonyl)imide ([MePrPyr⁺][NTf₂⁻]), and studied as an electrolyte for lithium-ion batteries. The graphite-lithium (C₆Li) anode, working together with vinylene carbonate as an additive showed ca. 90% of its initial discharge capacity after 50 cycles. The addition of vinylene carbonate to the neat ionic liquid results in the formation of the protective coating (SEI) on both the lithium and graphite anodes. The SEI formation increases the rate of the charge transfer reaction as well as protects the anode from chemical passivation (corrosion). The graphite-lithium (C₆Li) anode shows good cyclability and Coulombic efficiency in the presence of 10 wt.% of vinylene carbonate as an additive to the ionic liquid.     

Analysis of heterointerface recombination by Zn1−xMgxO for window layer of Cu(In,Ga)Se2 solar cells

An adjustment of a conduction band offset (CBO) of a window/absorber heterointerface is important for high efficiency Cu(In,Ga)Se₂ (CIGS) solar cells. In this study, the heterointerface recombination was characterized by the reduction of the thickness of a CdS layer and the adjustment of a CBO value by a Zn_1−xMg_xO (ZMO) layer. In ZnO/CdS/CIGS solar cells, open-circuit voltage (V_oc) and shunt resistance (R_sh) decreased with reducing the CdS thickness. In constant, significant reductions of V_oc and R_sh were not observed in ZMO/CdS/CIGS solar cells. With decreasing the CdS thickness, the CBO of (ZnO or ZMO)/CIGS become dominant for recombination. Also, the dominant mechanisms of recombination of the CIGS solar cells are discussed by the estimation of an activation energy obtained from temperature-dependent current-voltage measurements.     

Properties of the graphite-lithium anode in N-methyl-N-propylpiperidinium bis(trifluoromethanesulfonyl)imide as an electrolyte

The ternary [Li⁺][MPPip⁺][NTf₂⁻] ionic liquid, obtained by dissolution of solid lithium bis(trifluoromethanesulfonyl)imide (LiNTf₂) in liquid N-methyl-N-propylpiperidinium bis(trifluoromethanesulfonyl)imide (MPPipNTf₂), was used as an electrolyte, and stable at the lithium or graphite-lithium anodes. The graphite-lithium (C₆Li) anode showed good cyclability and Coulombic efficiency in the presence of a molecular additive (10 wt.% of vinylene carbonate, VC) to the ionic liquid. The electrode showed ca. 90% of its initial discharge capacity after 100 cycles. The addition of ethylene carbonate (EC) does not improve the cyclability of the anode to the same degree as that observed in the case of vinylene carbonate.     

Temperature dependence of Cu2ZnSn(SexS1−x)4 monograin solar cells

The temperature dependence of open-circuit voltage (V_oc), short-circuit current (I_sc), fill factor (FF), and relative efficiency of monograin Cu₂ZnSn(Se_xS_1−x)₄ solar cell was measured. The light intensity was varied from 2.2 to 100 mW/cm² and temperatures were in the range of T = 175-300 K. With a light intensity of 100 mW/cm²dV_oc/dT was determined to be −1.91 mV/K and the dominating recombination process at temperatures close to room temperature was found to be related to the recombination in the space-charge region. The solar cell relative efficiency decreases with temperature by 0.013%/K. Our results show that the diode ideality factor n does not show remarkable temperature dependence and slightly increases from n = 1.85 to n = 2.05 in the temperature range between 175 and 300 K.     

Novel photocatalysts based on Cd1−xZnxS/Zn(OH)2 for the hydrogen evolution from water solutions of ethanol

Multiphase photocatalysts Pt/Cd_1−xZn_xS/ZnO/Zn(OH)₂, Pt/Cd_1−xZn_xS/ZnO, and Pt/Cd_1−xZn_xS/Zn(OH)₂ were synthesized by a new two-step technique. The photocatalysts were characterized by a wide range of experimental techniques: X-ray diffraction, high-resolution transmission electron microscopy combined with energy-dispersive X-ray spectroscopy, low-temperature N₂ adsorption/desorption, and UV/VIS spectroscopy. The photocatalytic activity was tested in a batch reactor in the reaction of H₂ evolution from aqueous solutions of ethanol under visible light irradiation (λ > 420 nm). The highest achieved photocatalytic activity was 2256 μmol H₂ per gram of photocatalyst per hour; the highest quantum efficiency was 10.4%. The activity of Pt/Cd_1−xZn_xS/Zn(OH)₂ was higher than that of Pt/Cd_1−xZn_xS/ZnO/Zn(OH)₂ and Pt/Cd_1−xZn_xS/ZnO. The explanation of enhanced activity of zinc–cadmium sulfide/ε-zinc hydroxide based on quantum calculations was suggested.     

Synthesis and photovoltaic properties of an alternating phenylenevinylene copolymer with substituted-triphenylamine units along the backbone for bulk heterojunction and dye-sensitized solar cells

We have fabricated bulk heterojunction (BHJ) photovoltaic devices based on the as cast and thermally annealed P:[6,6]-phenyl-C-61-butyric acid methyl ester (PCBM) blends and found that these devices gave power conversion efficiency (PCE) of about 1.15 and 1.60% respectively. P is a novel alternating phenylenevinylene copolymer which contains 2-cyano-3-(4-(diphenylamino)phenyl)acrylic acid units along the backbone and was synthesized by Heck coupling. This copolymer was soluble in common organic solvents and showed long-wavelength absorption maximum at 390-420 nm with optical band gap of 1.94 eV. The improvement of PCE after thermal annealing of the device based on the P:PCBM blend was attributed to the increase in hole mobility due to the enhanced crystallinity of P induced by thermal treatment. In addition, we have fabricated BHJ photovoltaic devices based on the as cast and thermally annealed PB:P:PCBM ternary blend. PB is a low band gap alternating phenylenevinylene copolymer with BF₂-azopyrrole complex units, which has been previously synthesized in our laboratory. We found that the device based on this ternary blend exhibited higher PCE (2.56%) as compared to either P:PCBM (1.15%) or PB:PCBM (1.57%) blend. This feature was associated with the well energy level alignment of P, PB and PCBM, the higher donor-acceptor interfaces for the exciton dissociation and the improved light harvesting property of the ternary blend. The further increase in the PCE with thermally annealed ternary blend (3.48%) has been correlated with the increase in the crystallinity of both P and PB. Finally, we used copolymer P as sensitizer for quasi solid state dye-sensitized solar cell and we achieved PCE of approximately 3.78%.     

Electrochemical behavior of Li3−xM′xV2−yM″y(PO4)3 (M′ = K, M″ = Sc, Mg + Ti)/C composite cathode material for lithium-ion batteries

Composites of monoclinic Li_3−xM′_xV_2−yM″_2y(PO₄)₃ (M′ = K, M″ = Sc, Mg + Ti) with carbon were synthesized by solid-state reaction using oxalic acid or 6% H₂/Ar gas mixture as reducing agents at sintering temperature of 850 °C. The samples were characterized by X-ray diffraction (XRD), voltammetry and electrochemical galvanostatic cycling. The capacity of Li₃V₂(PO₄)₃ synthesized using hydrogen as the reducing agent was 127 mA h g⁻¹ and decreased to 120 mA h g⁻¹ after 20 charge-discharge cycles. The substitution of lithium and vanadium for other ions did not result in the improvement of the electrochemical characteristics of the samples.     

A review on energy pattern and policy for transportation sector in Malaysia

Transportation has dominated global fuel consumption and greenhouse gas emissions have risen in an alarming rate. Gasoline and diesel consumption for road transport have a faster growing rate than other sector and the trend appeared to be rapidly moving upwards in the near future. This has caused much concern in many countries including Malaysia to improve the sustainable energy of this sector. The focus of this paper is to analyze the trends of energy pattern and emission of road transport in Malaysia. On top of that, the review of prospective policies such as fuel economy standards and fuel switching to natural gas as well as biodiesel are summarized in this study. The study found that there is an urgent need to adopt suitable energy policy to balance the energy demand and reduce emission in this sector. This study serves as a guideline for further investigation and research in order to implement and improve the transportation sector.     

A field operational test on valve-regulated lead-acid absorbent-glass-mat batteries in micro-hybrid electric vehicles. Part I. Results based on kernel density estimation

In March 2007 the BMW Group has launched the micro-hybrid functions brake energy regeneration (BER) and automatic start and stop function (ASSF). Valve-regulated lead-acid (VRLA) batteries in absorbent glass mat (AGM) technology are applied in vehicles with micro-hybrid power system (MHPS). In both part I and part II of this publication vehicles with MHPS and AGM batteries are subject to a field operational test (FOT). Test vehicles with conventional power system (CPS) and flooded batteries were used as a reference. In the FOT sample batteries were mounted several times and electrically tested in the laboratory intermediately. Vehicle- and battery-related diagnosis data were read out for each test run and were matched with laboratory data in a data base. The FOT data were analyzed by the use of two-dimensional, nonparametric kernel estimation for clear data presentation.The data show that capacity loss in the MHPS is comparable to the CPS. However, the influence of mileage performance, which cannot be separated, suggests that battery stress is enhanced in the MHPS although a battery refresh function is applied. Anyway, the FOT demonstrates the unsuitability of flooded batteries for the MHPS because of high early capacity loss due to acid stratification and because of vanishing cranking performance due to increasing internal resistance. Furthermore, the lack of dynamic charge acceptance for high energy regeneration efficiency is illustrated. Under the presented FOT conditions charge acceptance of lead-acid (LA) batteries decreases to less than one third for about half of the sample batteries compared to new battery condition. In part II of this publication FOT data are presented by multiple regression analysis (Schaeck et al., submitted for publication [1]).     

Membrane electrode assemblies for high-temperature polymer electrolyte fuel cells based on poly(2,5-benzimidazole) membranes with phosphoric acid impregnation via the catalyst layers

A novel strategy for introducing phosphoric acid as the electrolyte into high-temperature polymer electrolyte fuel cells by using acid impregnated catalyst layers instead of pre-doped membranes is presented in this paper. This experimental approach is used for the development of membrane electrode assemblies based on poly(2,5-benzimidazole) (ABPBI) as the membrane polymer. The acid uptake of free-standing ABPBI used for this work amounts to ABPBI × 3.1 H₃PO₄ which has a specific conductivity of ∼80 mS cm⁻¹ at 140 °C. Rather thick catalyst layers (20% Pt/C, 1 mg Pt cm⁻², 40% PTFE as binder, d = 100-150 μm) are prepared on gas diffusion layers with a dense hydrophobic microlayer. After impregnation of the catalyst layers with phosphoric acid and assembling them with a mechanically robust undoped ABPBI membrane a fast redistribution of the electrolyte occurs during cell start-up. Power densities of about 250 mW cm⁻² are achieved at 160 °C and ambient pressure with hydrogen and air as reactants. Details of membrane properties, preparation and optimization of gas diffusion electrodes and fuel cell characterization are discussed. We consider our novel approach to be especially suitable for an easy and reproducible fabrication of MEAs with large active areas.