Thermal,Mechanical and Morphological Characterization of Jute/Gelatin Composites

Jute fabrics/gelatin biocomposites were fabricated using compression molding. The fiber content in the composite varied from 20–60 wt%. Composites were subjected to mechanical, thermal, water uptake and scanning electron microscopic (SEM) analysis. Composite contained 50 wt% jute showed the best mechanical properties. Tensile strength, tensile modulus, bending strength, bending modulus and impact strength of the 50% jute content composites were found to be 85 MPa, 1.25 GPa, 140 MPa and 9 GPa and 9.5 kJ/m², respectively. Water uptake properties at room temperature were evaluated and found that the composites had lower water uptake compared to virgin matrix.     

Jute Reinforced Polymer Composite by Gamma Radiation: Effect of Surface Treatment with UV Radiation

Jute (Hessian cloth) reinforced polymer composites were prepared with a mixture of 2-hydroxy ethyl methacrylate (HEMA) and aliphatic urethane diacrylate oligomer (EB-204), and then cured under gamma radiation. Thick pure polymer films (2 mm thickness) were prepared by using the same monomer and oligomer at different weight ratios, and 500 krad of total gamma radiation dose at 600 krad/hr was selected for the curing of all composites. Total radiation dose, jute content, and monomer concentration were optimized with the extent of mechanical properties. Among all resulting composites, the composite of 38% jute content at monomer:oligomer = 50:50 (w/w) ratios showed the better mechanical properties, such as 108% increase in tensile strength (TS), 58% increase in bending strength (BS), 138% increase in tensile modulus (TM), and 211% increase in bending modulus (BM) relative to pure polymer film. The gel content values were also found to increase with the increase of jute content in the composite. But the elongation at break (Eb) for both tensile and bending was found to decrease with increasing jute content. The best mechanical properties were obtained when jute fibers were pre-irradiated with UV radiation, such as 150% increase in TS, 90% increase in BS relative to polymer film, 19% increase in TS, and 15% increase in BS relative to untreated jute-based composites. A water uptake behavior investigation of the resulting composites was also performed and composites based on UV-treated jute showed the minimum water uptake value.     

Fabrication and Mechanical Characterization of Jute Fabrics: Reinforced Polyvinyl Chloride/Polypropylene Hybrid Composites

Jute fabrics such as reinforced polyvinyl chloride (PVC), polypropylene (PP), and a mixture of PVC and PP matrices-based composites (50 wt% fiber) were prepared by compression molding. Tensile strength (TS), bending strength (BS), tensile modulus (TM), and vbending modulus (BM) of jute fabrics' reinforced PVC composite (50 wt% fiber) were found to be 45 MPa, 52 MPa, 0.8 GPa, and 1.1 GPa, respectively. The effect of incorporation of PP on the mechanical properties of jute fabrics' reinforced PVC composites was studied. It was found that the mixture of 60% PP and 40% PVC matrices based composite showed the best performance. TS, BS, TM, and BM for this composite were found to be 65 MPa, 70 MPa, 1.42 GPa, and 1.8 GPa, respectively. Degradation tests of the composites for up to six months were performed in a soil medium. Thermo-mechanical properties of the composites were also studied.     

Effect of Ultraviolet Radiation on the Mechanical and Dielectric Properties of Hessian Cloth/PP Composites with Starch

Hessian cloth (jute fabrics) reinforced poly(propylene) (PP) composites (45 wt% fiber) were prepared by compression molding and the mechanical properties were evaluated. Jute fabrics and PP sheets were treated with UV radiation at different intensities and then composites were fabricated. It was found that mechanical properties of the irradiated jute and irradiated PP-based composites were found to increase significantly compared to that of the untreated counterparts. Irradiated jute fabrics were also treated with aqueous starch solution (1–5%, w/w) for 2–10 min. Composites made of 3% starch-treated jute fabrics (5 min soaking time) and irradiated PP showed the best mechanical properties. Tensile strength, bending strength, tensile modulus, bending modulus and impact strength of the composites were found to improve 31, 41, 42, 46 and 84% higher over untreated composites. Water uptake, thermal degradation and dielectric properties of the resulting composites were also performed.     

Comparative Studies of Mechanical and Interfacial Properties Between Jute Fiber/PVC and E-Glass Fiber/PVC Composites

Composites (50 wt% fiber) of jute fiber reinforced polyvinyl chloride (PVC) matrix and E-glass fiber reinforced PVC matrix were prepared by compression molding. Mechanical properties such as tensile strength (TS), tensile modulus (TM), bending strength (BS), bending modulus (BM) and impact strength (IS) of both types of composites was evaluated and compared. Values of TS, TM, BS, BM and IS of jute fiber/PVC composites were found to be 45 MPa, 802 MPa, 46 MPa, 850 MPa and 24 kJ/m², respectively. It was observed that TS, TM, BS, BM and IS of E-glass fiber/PVC composites were found to increase by 44, 80, 47, 92 and 37.5%, respectively. Thermal properties of the composites were also carried out, which revealed that thermal stability of E-glass fiber/PVC system was higher. The interfacial adhesion between the fibers (jute and E-glass) and matrix was studied by means of critical fiber length and interfacial shear strength that were measured by single fiber fragmentation test. Fracture sides after flexural testing of both types of the composites were investigated by Scanning Electron Microscopy.     

The Preparation and Characterization of Silk/Gelatin Biocomposites

There is a growing interest in the use of composite materials. Silk fiber/gelatin biocomposites were fabricated using compression molding. The fiber content in the composite varied from 10–30 wt%. Composite containing 30 wt% silk showed the best mechanical properties. Tensile strength, tensile modulus, bending strength, bending modulus and impact strength, hardness of the 30% silk content composites were found 54 MPa, 0.95 GPa, 75 MPa and 0.43 GPa and 5.4 kJ/m², 95.5 Shore A, respectively. Water uptake properties at room temperature, accelerated weathering aging, irradiation, thermomechanical analysis, and degradation in soil were carried out in this experiment.     

Mechanical and Electrical Properties of Jute Fabrics Reinforced Polyethylene/Polypropylene Composites: Role of Gamma Radiation

Jute fabrics reinforced polyethylene (PE), polypropylene (PP) and mixture of PP+PE matrices based composites (50 wt% fiber) were prepared by compression molding. It was found that the mixture of 80% PP + 20% PE hybrid matrices based jute fabrics reinforced composites performed the best results. Gamma radiation (250–1000 krad) was applied on PP, PE and jute fabrics then composites were fabricated. The mechanical properties of the irradiated composites (500 krad) were found to increase significantly compared to that of the non irradiated composites. Electrical properties like dielectric constant, loss tangent and conductivity with temperature variation of the composites were studied.     

Fabrication and comparative mechanical,electrical and water absorption characteristic properties of multifunctional epoxy resin of bisphenol-C and commercial epoxy-treated and -untreated jute fiber-reinforced composites

Epoxy resin of bisphenol-C-formaldehyde (EBCF) was synthesized and its structure was confirmed by FTIR and ¹HNMR techniques. Untreated jute and a 4 % sodium hydroxide-treated jute composites of EBCF, araldites (GY508 and GY6010) and their hybrid composites were fabricated by hand layup technique followed by compression-molding technique. Mechanical, electrical and water absorption behavior of the composites was studied by standard test methods. The composites showed good mechanical and electrical properties, excellent hydrolytic stability and almost identical water absorption tendency. To some extent, alkali-treated jute composites displayed improved mechanical properties and water absorption tendency. EBCF-based jute and hybrid composites showed comparable mechanical and electrical properties and water absorption behavior with araldite-based composites. Among jute–EBCF, jute–araldite and their hybrid composites, J–EBCF showed the highest impact strength (26 kg m^?2), Barcol hardness (34), volume resistivity (2.7 × 10^?11 Ω cm) and diffusivity (7.19 × 10^?13 m² s^?2). J–GY-1 showed the highest tensile strength (43.7 MPa), flexural modulus (4.26 GPa), % equilibrium water absorption (19.36 %) and equilibrium water absorption time (480 h). Good mechanical and electrical properties and excellent hydrolytic stability of both types of the composites suggested their usefulness for low load-bearing housing, and electrical and marine applications. Thus, EBCF has found its commercial importance as that of the commercial araldite resins.     

Physico-Mechanical,Interfacial, Degradation,and Dielectric Properties of Jute/PP Composites: Effect of Dye and Gamma Radiation

Jute fabrics/polypropylene composites were prepared by compression molding. Jute fabrics were treated with red dye solutions (0.1–1%, w/w) for different soaking times and we found that 0.5% red-dye-treated jute/PP composite for 5 min soaking time showed better results. Gamma radiation (250-1000 krad dose) was applied on both jute and matrices. Composites were fabricated with non-irradiated jute/non-irradiated PP (C-0), non-irradiated jute/irradiated PP (C-1), irradiated jute/non-irradiated PP (C-2), and irradiated jute/irradiated PP (C-3). It was found that a C-3 composite made using 500 krad dose showed the best results. Simulating weathering and dielectric properties of the composites were also performed.     

Mechanical and viscoelastic properties of soybean oil thermoset reinforced with jute fabrics and carded lyocell fiber

Composites and hybrid composites were manufactured from renewable materials based on jute fibers, regenerated cellulose fibers (Lyocell), and thermosetting polymer from soybean oil. Three different types of jute fabrics with biaxial weave architecture but different surface weights, and carded Lyocell fiber were used as reinforcements. Hybrid composites were also manufactured by combining the jute reinforcements with the Lyocell. The Lyocell composite was found to have better mechanical properties than other composites. It has tensile strength and modulus of about 144 MPa and 18 GPa, respectively. The jute composites also have relatively good mechanical properties, as their tensile strengths and moduli were found to be between 65 and 84 MPa, and between 14 and 19 GPa, respectively. The Lyocell‐reinforced composite showed the highest flexural strength and modulus, of about 217 MPa and 13 GPa, respectively. In all cases, the hybrid composites in this study showed improved mechanical properties but lower storage modulus. The Lyocell fiber gave the highest impact strength of about 35 kJ/m², which could be a result of its morphology. Dynamic mechanical analysis showed that the Lyocell reinforced composite has the best viscoelastic properties. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effect of alkaline treatment on physical,mechanical, and thermal characteristics of jute filler reinforced epoxy composites

With burgeoning environmental concerns worldwide, using natural fibers/fillers to produce composites rather than conventional fibers is on the rise. The current work focuses on the physical and thermomechanical characteristics of alkaline-treated jute filler-based epoxy composites. The composites have been prepared with different weight fraction of jute fillers (0%, 2.5%, 5%, 7.5%, 10%, and 12.5%) using hand layup process. The X-ray diffraction and Fourier transform infrared spectroscopy analysis observed that the alkali treatment of jute fillers improved the crystallinity and molecular structure, enhancing the interfacial and molecular bond between fillers and matrix. The mechanical characterizations of developed composites analyzed that the inclusion of treated jute fillers strengthened the tensile and flexural properties. The 5% filler-based composites have demonstrated maximum tensile strength (54.06 MPa) and modulus (3.12 GPa) with maximum flexural strength (67.55 MPa) and modulus (3.90 GPa). The viscoelastic characteristics of composites revealed that the 7.5% filler-based composite has the highest storage modulus (3.75 GPa), loss modulus (0.496 GPa), and glass transition temperature (91°C) due to greater interfacial interactions of molecules. The weight loss and degradation of composites analyzed with thermogravimetric analysis, and observed better thermal stability with treated jute fillers. The morphological analysis at fracture surfaces analyzed the brittle catastrophic failure of composites. Therefore, the finding produced better specific strength and stiffness with greater thermal stability for electronics equipment, packaging, and transportation.     

Comparative experimental measurements of jute fiber/polypropylene and coir fiber/polypropylene composites as ionizing radiation

Jute and coir fiber‐reinforced polypropylene (PP) composites (45 wt% fiber) were prepared by compression molding. Composites were fabricated with irradiated jute fiber/irradiated PP and irradiated coir fiber/irradiated PP at different doses (250–1,000 krad). It was revealed that jute‐based composites had better mechanical properties as compared to coir‐based composites. Interfacial shear strength of jute/PP and coir/PP systems was measured by using the single‐fiber fragmentation test. Scanning electron microscopy investigation shows poor fiber matrix adhesion for coir‐based composites than that of jute‐based composites. Water uptake and soil degradation tests of the composites were also performed. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Thermomechanical and Interfacial Properties of Calcium Alginate Fiber-Reinforced Polypropylene Composites

Polypropylene (PP) matrix calcium alginate fiber reinforced unidirectional composites (10% fiber by weight) were fabricated by compression molding. Tensile strength (TS), tensile modulus (TM), bending strength (BS), bending modulus (BM), and impact strength (IS) were found to be 26 MPa, 950 MPa, 38 MPa, 1320 MPa, and 20 kJ/m², respectively. Degradation tests of composites were performed for 6 weeks in soil and it was found that composites retained almost 75% of its original strength. The interfacial properties of the composite were investigated by using single fiber fragmentation test (SFFT) and by scanning electron microscope (SEM).     

A Comparative Study on the Mechanical,Degradation and Interfacial Properties of Jute/LLDPE and Jute/Natural Rubber Composites

Jute fabric (hessian cloth) reinforced low-density polyethylene (LLDPE) composites (40 wt%) and solid natural rubber-(NR) based composites (40 wt%) were fabricated by compression molding. Tensile strength (TS), tensile modulus (TM) and percentage elongation at break (Eb) of jute/LLDPE composites were found to be 29, 680 MPa and 20%, and for jute/NR-based composites were also found to be 15, 122 MPa and 94%, respectively. Interfacial shear strength (IFSS) of the jute/LLDPE and jute/NR systems was investigated by using the single fiber fragmentation test (SFFT). Scanning electron microscopy (SEM) and aqueous degradation tests were also performed.     

Synthesis and physicochemical study of bisphenol‐C‐formaldehyde‐toluene diisocyanate polyurethane–jute and jute–rice husk/wheat husk composites

Bisphenol‐C‐formaldehyde‐toluene‐2,4‐di isocyanate polyurethane (PU) has been synthesized at room temperature and used for the fabrication of jute and jute–rice husk/wheat husk hybrid composites. PU–jute and PU–jute–RH/WH composites were prepared under pressure of 30.4 MPa at room temperature for 8 h, while PU–jute–RH/WH composites were prepared under same pressure at 110°C for 5 h. PU–jute composite has good tensile strength and flexural strength (50–53 MPa), while PU–jute–RH/WH hybrid composites have moderate tensile strength (9–11 MPa) and a fairly good flexural strength (15–31 MPa). Composites possess 1.1–2.2 kV electric strength and 0.94–1.26 × 10¹² ohm cm volume resistivity. Water absorption in PU–jute composite is different in water (9.75%), 10% HCl (12.14%), and 10% NaCl (6.05%). Equilibrium water uptake time in salt environment is observed 96 h, while in pure water and acidic environments it is 192 h. In boiling water equilibrium water content and equilibrium time are found to be 21.7% and 3 h, respectively. Water absorption increased 2.2 times in boiling water, whereas equilibrium time reduced 64 times. Thus, PU–jute composite has excellent hydrolytic stability against boiling water, 10% HCl, and 10% NaCl solutions. Fairly good mechanical and electrical properties and excellent hydrolytic stability of composites signify their usefulness for low cost housing units and in electrical and marine industries. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2363–2370, 2006     

Proton-conducting ceramics as electrode/electrolyte materials for SOFC's—part I: preparation,mechanical and thermal properties of sintered bodies

The aim of these investigations was to prepare and to examine compounds of a high temperature solid oxide fuel cell with a proton conducting electrolyte in view of the mechanical and thermal properties. The powders were made by the conventional solid reaction of carbonates and oxides. The stoichiometry of the electrolyte Ba,Ca niobate (BCN) was varied with x=0, x=0.12 and x=0.18. As potential cathode material SrCeO₃ and SrZrO₃ stabilised with 5% Yb was prepared, and as anode material cermet of BCN and Ni with 50:50 wt.% was synthesised. The mechanical properties like bending strength (room and high temperature), Young modulus (E), modulus of rigidity (G), Poison's ratio, micro hardness and fracture toughness were measured on sintered samples. The highest values for bending strength, E and G could be found for BCN12 (156 MPa, 160 GPa, 63 GPa) and the cerate (175 MPa, 145 GPa, 56 GPa), the lowest for the cermet BCN/Ni (72 MPa, 68 GPa, 29 GPa). The investigation of the thermal properties of the bulk material showed a thermal stability to a temperature of 1400 °C. The thermal expansion coefficient measured at 1000 °C was found to be in the range of 10–12×10⁻⁶/K. Further investigations with respect to the mechanical and thermal properties have to be made for the whole system of cathode–electrolyte–anode.     

Preparation and Characterization of Gelatin-Based PVA Film: Effect of Gamma Irradiation

Gelatin-based polyvinyl alcohol (PVA) films were prepared (using a casting process) by mixing aqueous solutions of gelatin and PVA in different ratios. Monomer 1, 4-butanediol diacrylate (BDDA) was dissolved in methanol. Films containing 95% gelatin + 5% PVA were soaked in 3% BDDA monomer (w/w). These films were then irradiated under gamma radiation (⁶⁰Co) at different doses (50–500 krad) at a dose rate of 350 krad/h. The physico-mechanical and thermal properties of these films were evaluated. It was evident that 5% PVA-containing gelatin blend film exhibited the highest tensile strength (TS) value at 50 krad (51 MPa), which was 46% higher than that of non-irradiated blend films. It was also found that incorporation of PVA significantly reduced the TS value of the blend films compared to the raw film, whereas elongation at break (Eb) value was increased. A significant improvement of the blend films was also confirmed by thermogravimetric analysis (TGA) and thermo-mechanical analysis (TMA) when the acrylate group (from BDDA) was introduced into the film.     

Effect of γ-Radiation on the Mechanical Performance of Hybrid Rice Straw/Seaweed-Polypropylene Composites

Hybrid composites of rice straw (Rs)/seaweed (Sw) and polypropylene (PP) were prepared at a fixed filler ratio of 30:70 and variable ratio of the two reinforcements, viz. 30:0, 25:5, 20:10, 10:20, 0:30 by weight. Mechanical properties of the composites such as tensile strength (TS), bending strength (BS), impact strength (IS) and elongation at break (Eb%) were investigated and the composite formulation of 20:10:70 (Rs:Sw:PP) was found to be optimum that showed TS = 2.8 MPa, BS = 68 N/mm², IS = 2.5 kJ/mm² and Eb = 50%. For better compatibility, Rs and Sw were subjected to surface treatment using various intensities of γ-radiation to prepare improved hybrid composites. γ-irradiated filler hybrid composites significantly enhanced mechanical properties and the composite in which fillers were irradiated at 100 krad achieved maximum enhancement with TS = 35 MPa, BS = 75 N/mm², IS = 2.7 kJ/mm² and Eb = 68%. Water absorption capacity of the different composites was also studied and irradiated filler composites showed less water uptake.     

Role of gamma radiation and EGDMA on the physico–mechanical properties of jute fabrics/polypropylene composites

Jute fabrics reinforced polypropylene (PP) composites (45 wt % fiber) were prepared by compression molding and their mechanical properties were investigated. Both jute fabrics and PP sheets were treated with gamma radiation (250–1,000 krad dose) at a rate of 350 krad/h. Irradiated jute fabrics were soaked into ethylene glycol dimethacrylate (EGDMA) solutions (5–40% by weight) and cured in an oven at different temperatures (40–100°C) for 60 min. The percentage of polymer loading (PL) was evaluated and found that 20% EGDMA‐treated jute fabrics contains the highest PL. Composites made of 20% EGDMA‐treated jute fabrics were studied further. It was found that the treatment using the EGDMA improved the mechanical properties of the composites significantly. Scanning electron microscopy and aging properties of untreated and treated composites were performed. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers     

Processing and mechanical performance of 3D Cf/SiCN composites prepared by polymer impregnation and pyrolysis

The processing of 3D carbon fiber reinforced SiCN ceramic matrix composites prepared by polymer impregnation and pyrolysis (PIP) route was improved, and factors that determined the mechanical performance of the resulting composites were discussed. 3D C_f/SiCN composites with a relative density of ∼81% and uniform microstructure were obtained after 6 PIP cycles. The optimum bending strength, Young's modulus and fracture toughness of the composites were 75.2 MPa, 66.3 GPa and 1.65 MPa m^1/2, respectively. The residual strength retention rate of the as-pyrolyzed composites was 93.3% after thermal shock test at ΔT = 780 °C. It further degraded to 14.6% when the thermal shock temperature difference reached to 1180 °C. The bending strength of the composites was 35.6 MPa after annealing at 1000 °C in static air. The deterioration of the bending strength should be attributed to the strength degradation of carbon fibers and decomposition of interfacial structure.