Investigation on thermoplastic co‐poly(ether‐ester) elastomer toughened poly(methylmethacrylate) blends

Blends of poly(methyl methacrylate) (PMMA) and copoly(ether‐ester) (COPE) elastomer have been prepared in different compositions namely, 95/5, 90/10, 85/15, and 80/20 wt % (PMMA/COPE), by melt mixing technique using twin screw extruder. The influence of COPE content on the mechanical properties especially impact strength, thermal behavior, and chemical resistance of PMMA have been investigated. The impact strength of the PMMA/COPE blends for all the compositions were found to be improved remarkably as compared to the virgin PMMA without affecting the other mechanical properties significantly. Various composite models, such as series model, parallel model, Halpin‐Tsai equation, and Kerner's model have been used to fit the experimental mechanical properties. The effect of chemical and thermal ageing on the performance of the PMMA/COPE blends was also studied. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Poly(methyl methacrylate) toughened by ethylene‐vinyl acetate copolymer: Physico‐mechanical,thermal, and chemical properties

Blends of poly(methyl methacrylate) (PMMA) with different composition viz., 5, 10, 15, and 20 wt % of ethylene‐vinyl acetate (EVA) copolymer were prepared by extrusion in a corotating twin screw extruder. These prepared PMMA/EVA blends have been characterized for physicomechanical properties such as density, surface hardness, izod impact strength, tensile strength, tensile elongation, and tensile modulus. The chemical aging and heat aging tests were performed on the blends by exposing them to different chemical environments and to 80°C for 168 h respectively. The influence of chemical aging and heat ageing on the mechanical performance of PMMA/EVA blends has been studied. The PMMA/EVA blends were also characterized for thermal properties such as vicat softening point (VSP) and melt flow index (MFI). That means significant improvement in impact strength of PMMA was noticed after incorporation of EVA into PMMA matrix and it lies in the range 19.1–31.96 J/m. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Thermal and mechanical properties of poly(methyl methacrylate) and ethylene vinyl acetate copolymer blends

A series of poly(methyl methacrylate) (PMMA) blends have been prepared with different compositions viz., 5, 10, 15, and 20 wt % ethylene vinyl acetate (EVA) copolymer by melt blending method in Haake Rheocord. The effect of different compositions of EVA on the physico‐mechanical and thermal properties of PMMA and EVA copolymer blends have been studied. Differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA) and thermogravimetric analysis (TGA) has been employed to investigate the phase behavior of PMMA/EVA blends from the point of view of component specific interactions, molecular motions and morphology. The resulting morphologies of the various blends also studied by optical microscope. The DSC analysis indicates the phase separation between the PMMA matrix and EVA domains. The impact strength analysis revealed a substantial increase in impact strength from 19 to 32 J/m. The TGA analysis reveals the reduction in onset of thermal degradation temperature of PMMA with increase in EVA component of the blend. The optical microscope photographs have demonstrated the PMMA/EVA system had a microphase separated structure consisting of dispersed EVA domains within a continuous PMMA matrix. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Dynamic mechanical, thermal, physico-mechanical and morphological properties of LLDPE/EMA blends

The effect of blend composition on the morphology, dynamic mechanical properties, thermal and physico-mechanical properties of linear low density polyethylene (LLDPE)/ ethylene-co-methyl acrylate (EMA) blends were studied. The blend showed both dispersed and continuous phase morphology that depends on the blend composition. A co-continuous structure is formed for blends containing 50 wt% of EMA. Dynamic mechanical studies showed that flexibility of the blend enhanced with the expansion of the amorphous region as EMA content increased. However, two separate melting temperature peak observed in differential scanning calorimetry (DSC) analysis indicate that the blends are immiscible in crystalline region of the two polymers. X-ray diffraction (XRD) studies showed that crystallinity of blends decreases with increase in EMA content and negative deviation of tensile strength from the mixing rule indicates the poor interfacial adhesion between the two components. FTIR spectroscopy established the lack of chemical interaction between LLDPE and EMA, which support the SEM, DSC, DMA and XRD observations. Parallel-Voids model has been applied to characterize phase morphology of these blends.     

Effect of Acrylonitrile-Butadiene-Styrene High-Rubber Powder and Strain Rate on the Morphology and Mechanical Properties of Acrylonitrile-Butadiene-Styrene/Poly (Methyl Methacrylate) Blends

Acrylonitrile-butadiene-styrene (ABS) high-rubber powder (HRP) toughened acrylonitrile-butadiene-styrene (ABS)/polymethyl methacrylate (PMMA) blends were prepared in a co-rotating twin screw extruder. The effect of ABS HRP on mechanical and morphology properties of ABS/PMMA blends was studied. It is shown that the toughness of ABS/PMMA blends was improved effectively with the incorporation of ABS HRP, while the elastic modulus and tensile strength decrease slightly. Tensile tests at different strain rates were carried out in order to investigate the influence of strain rate on mechanical properties of various blends. Finally, the strain rate sensitive behavior of different blends was explored by using the Eyring model.     

HTPB/液化MDI型PU与PMMA的共混研究

用同步聚合法制备了一系列HTPB／液化MDI型PU与PMMA的共混材料，分别用FTIR、DSC、SEM和拉力实验机对共混材料的反应进度、玻璃化转变温度、力学性能和微观形态进行了考查和研究；结果表明，体系中PMMA优先于PU聚合，共混材料的玻璃化转变温度Tg2随PMMA质量分数的增加略呈上升趋势；材料的拉伸强度和硬度均随体系中PMMA质量分数的增加而增大，断裂伸长率则逐渐减小；体系微观呈两相分离，当PMMA占50％时，相畴最小。     

N-环己基马来酰亚胺／甲基丙烯酸甲酯／苯乙烯乳液共聚物与PVC共混的研究

通过乳液共聚合得到N-环己基马来酰亚胺(ChMI)、甲基丙烯酸甲酯(MMA)、苯乙烯(St)的三元共聚物(ECMS)，用共聚物作耐热改性剂与PVC共混，用TBA和TGA研究了共聚物含量对共混物热性能、力学性能、流变性能及维卡软化点的影响。结果表明随三元共聚物含量的增加，共混物的玻璃化温度及维卡软化点逐渐上升；PVC第一阶段降解完毕。后平台区残留量逐渐上升；拉伸强度提高，冲击强度下降；熔体表观粘度增加，呈假塑性流体。     

Effects of compatibilizer on the morphological,mechanical, and rheological properties of poly(methyl methacrylate)/poly(N‐methyl methacrylimide) blends

The effects of compatibilizer on the morphological, thermal, mechanical, and rheological properties of poly(methyl methacrylate) (PMMA)/poly(N‐methyl methacrylimide) (PMMI) (70/30) blends were investigated. The compatibilizer used in this study was styrene–acrylonitrile–glycidyl methacrylate (SAN‐GMA) copolymer. Morphological characterization of the PMMA/PMMI (70/30) blend with SAN‐GMA showed a decrease in PMMI droplet size with an increase in SAN‐GMA. The glass‐transition temperature of the PMMA‐rich phase became higher when SAN‐GMA was added up to 5 parts per hundred resin by weight (phr). The flexural and tensile strengths of the PMMA/PMMI (70/30) blend increased with the addition of SAN‐GMA up to 5 phr. The complex viscosity of the PMMA/PMMI (70/30) blends increased when SAN‐GMA was added up to 5 phr, which implies an increase in compatibility between the PMMA and PMMI components. From the weighted relaxation spectrum, which was obtained from the storage modulus and loss modulus, the interfacial tension of the PMMA/PMMI (70/30) blend was calculated using the Palierne emulsion model and the Choi‐Schowalter model. The results of the morphological, thermal, mechanical, and rheological studies and the values of the interfacial tension of the PMMA/PMMI (70/30) blends suggest that the optimum compatibilizer concentration of SAN‐GMA is 5 phr. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43856.     

Effect of nanoclay on the morphology and properties of poly(methyl methacrylate)/high‐density polyethylene blends

The effect of nanoclay on the morphology and properties of poly(methyl methacrylate) (PMMA)/high‐density polyethylene (HDPE) blends was studied. A scanning electron microscopy study of the PMMA/HDPE (70/30 w/w) blends with nanoclay indicated a reduction in the average domain sizes of the dispersed HDPE phase and, hence, a better extent of mixing compared to that of the blends without any nanoclay. An X‐ray diffraction study and transmission electron microscopy revealed the localization of intercalated nanoclay in the PMMA matrix of the PMMA/HDPE (70/30 w/w) blend. However, the same effect of clay was not observed in the PMMA/HDPE (30/70 w/w) blend when HDPE became the matrix. In the PMMA/HDPE (30/70 w/w) blend, the addition of nanoclay increased the domain size of the dispersed PMMA domains by preferential location of the clays inside the PMMA domains. The addition of polyethylene‐grafted maleic anhydride in both compositions of the PMMA/HDPE blend effectively reduced the domain size of the disperse phases in the blend. However, the presence of clay increased the tensile strength and storage modulus of the PMMA/HDPE blends in both blend compositions. Thus, in the PMMA/HDPE blend, the clay platelets acted as a effective compatibilizer as long as they were dispersed mainly in the matrix phase. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

CPVC/PMMA共混体系的性能研究

制备了氯化聚氯乙烯/聚甲基丙烯酸甲酯(CPVC/PMMA)共混材料,研究了PMMA的引入对CPVC/PMMA共混体系的力学性能、耐热性能、表面光泽度、加工流动性和微观结构的影响。结果表明:适量PMMA的引人,使CPVC/PMMA共混体系的缺口冲击强度和光泽度较纯CPVC显著提高,耐热性能亦有所改善,而拉伸强度下降不明显;塑炼过程中,CPVC/PMMA共混体系熔体的平衡扭矩降低,凝胶化时间减少。当PMMA含量为15 phr时,CPVC/PMMA共混体系具有最佳综合性能,此时该共混体系的缺口冲击强度为5.4 kJ/m2,拉伸强度为53.5 MPa,表面光泽度为82.3%,热变形温度为102.4℃,平衡扭矩为20.1 N·m。     

丙烯酸酯接枝改性天然橡胶增韧聚乳酸

通过在天然橡胶(NR)分子链上接枝甲基丙烯酸甲酯(MMA)和丙烯酸丁酯(BA),制备了三种丙烯酸酯接枝改性NR:NR-g-PMMA,NR-g-PBA和NR-g-(PMMA,PBA)。采用核磁共振氢谱对三种接枝物进行了化学结构鉴定。将接枝改性后的NR和未改性的NR与PLA采用哈克密炼机熔融共混,分别制备了PLA/NR,PLA/NR-gPMMA,PLA/NR-g-PBA和PLA/NR-g-(PMMA,PBA)共混物,研究了接枝改性NR和未改性NR含量对共混物力学性能和热性能的影响。各共混物的拉伸弹性模量和拉伸强度均随接枝改性NR和未改性NR含量的增加而降低,断裂伸长率和缺口冲击强度随接枝改性NR和未改性NR含量的增加而提高。其中,PLA/NR-g-PBA共混物的断裂伸长率和缺口冲击强度比其它共混物提高的幅度大,当NR-g-PBA的质量分数为5%时,PLA/NR-g-PBA共混物的断裂伸长率达到78%,缺口冲击强度为5.2 k J/m2,而纯PLA的断裂伸长率仅为7.7%,缺口冲击强度为2.5 k J/m2,说明NR接枝分子柔顺性较高的BA更有利于促进其与PLA共混物的韧性提高。热分析结果表明,PLA/NR-gPBA共混物的热稳定性相比于纯PLA也有所提高。     

Miscibility,water uptake,ion exchange capacity,conductivity and dielectric studies of poly(methyl methacrylate) and cellulose acetate blends

In the last few decades, polymer blends with good miscibility and conductivity have been the focus of study for material scientists. Here, polymer blends of Poly(methyl methacrylate) (PMMA) and Cellulose acetate (CA) of varying blend compositions have been prepared by solution casting method and their miscibility, water uptake, ion exchange capacity (IEC) proton conductivity, and dielectric properties have been studied. Dimethyl formamide (DMF) was used as solvent. Fourier transform infrared spectra (FTIR) and Differential scanning calorimetry (DSC) measurements have been used to analyze the miscibility of the blends. Up to 50/50 PMMA/CA, water uptake showed an increasing trend and for other compositions the value decreased. Ion exchange capacity and conductivity of the blends decreased with increase in PMMA content of the blends. The variations in the blend properties have been attributed to the presence of specific interactions and exchangeable groups in the blend system. The proton conductivity of the blends is in the order of 10^?3 S cm^?1. Impedance analysis of the blends indicated the absence of any relaxation phenomenon in the blend system. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 3074–3081, 2013     

A study on weld line morphology and mechanical strength of injection molded polystyrene/poly(methyl methacrylate) blends

In this work, the mechanical strength and weld line morphology of injection molded polystyrene/poly(methyl methacrylate) (PS/PMMA) blends were investigated by scanning electron microscopy (SEM) and mechanical property test. The experimental results show that the tensile strength of PS/PMMA blends get greatly decreased due to the presence of the weld line. Although the tensile strength without the weld line of PS/PMMA (70/30) is much higher than that of the PS/PMMA (30/70) blend, their tensile strength with weld line shows reversed change. The viscosity ratio of dispersed phase over matrix is a very important parameter for control of weld‐line morphology of the immiscible polymer blend. In PS/PMMA (70/30) blend, the PMMA dispersed domains at the core of the weld line are spherically shaped, which is the same as bulk. While in the PS/PMMA (30/70) blend, the viscosity of the dispersed PS phase is lower than that of the PMMA matrix, the PS phase is absent at the weld line, and PS particles are highly oriented parallel to the weld line, which is a stress concentrator. This is why weld line strength of PS/PMMA (30/70) is lower than that of PS/PMMA (70/30) blend. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1856–1865, 2002; DOI 10.1002/app.10450     

Natural rubber‐g‐methyl methacrylate/poly(methyl methacrylate) blends

The grafting of the methyl methacrylate (MMA) monomer onto natural rubber using potassium persulfate as an initiator was carried out by emulsion polymerization. The rubber macroradicals reacted with MMA to form graft copolymers. The morphology of grafted natural rubber (GNR) was determined by transmission electron microscopy and it was confirmed that the graft copolymerization was a surface‐controlled process. The effects of the initiator concentration, reaction temperature, monomer concentration, and reaction time on the monomer conversion and grafting efficiency were investigated. The grafting efficiency of the GNR was determined by a solvent‐extraction technique. The natural rubber‐g‐methyl methacrylate/poly(methyl methacrylate) (NR‐g‐MMA/PMMA) blends were prepared by a melt‐mixing system. The mechanical properties and the fracture behavior of GNR/PMMA blends were evaluated as a function of the graft copolymer composition and the blend ratio. The tensile strength, tear strength, and hardness increased with an increase in PMMA content. The tensile fracture surface examined by scanning electron microscopy disclosed that the graft copolymer acted as an interfacial agent and gave a good adhesion between the two phases of the compatibilized blend. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 428–439, 2001     

ABS／PMMA合金的配比与性能

制备不同配比的ABS／PMMA合金,分别测试其缺口冲击强度、拉促强度、热变形温度、熔体指数,结果表明：1）ABS中引入PMMA强以提高耐热,2）ABS与PMMA共混能提高PMMA的力学性能特别是缺口冲击强度。3）当ABS／PMMA中PMMA为20％时,共混物具有最优的力学性能。4）一般情况下,ABS／PMMA合金的流动性介于ABS和PMMA的之间。     

Investigation of the structural,thermal, mechanical,and optical properties of poly(methyl methacrylate) and poly(vinylidene fluoride) blends

In this investigation, poly(methyl methacrylate) (PMMA) and poly(vinylidene fluoride) (PVDF) blends (w/w) were prepared in a Brabender (South Hackensack, NJ) plasticorder with a thermoplastic mixing chamber (type W60) preheated at 180°C. These blends were further converted into films by a conventional solution casting method and characterized with Fourier transform infrared spectroscopy, differential scanning calorimetry, X‐ray diffraction, mechanical property measurements, impact strength testing, ultraviolet–visible spectroscopy, refractive‐index measurements, and contact‐angle study. The Fourier transform infrared results indicated that the compatibility between these two systems resulted from hydrogen bonding between the carbonyl group of PMMA and the CH₂ group of PVDF. The thermal analysis showed depressions in the glass‐transition temperature, melting temperature, and crystallization temperature. The heat of crystallization increased with an increase in the PVDF content in the blend. An increase in the heat of crystallization meant an increase in the crystallinity. An increase in the cooling rate increased the crystallization rate. The improvement in the mechanical properties of the blend films indicated that the observed behavior was ascribable to a more coherent structure of the blends due to strong specific interactions between PMMA and PVDF chains. The impact strength analysis revealed a substantial increase in the impact strength from 21.64 to 38.52 J/m. Optical absorption spectra suggested the presence of an optical band gap energy that increased with an increase in the PVDF content in the blend. The contact angle against water increased with the PVDF content in the blend film, and this was caused by the hydrophobicity of PVDF due to the CF₂ group of PVDF. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Compatibility enhancement of ABS/polycarbonate blends

The effects of blend composition, melt viscosity of poly(acrylonitrile-butadiene-styrene) (ABS), and compatibilizing effect of poly(methyl methacrylate) (PMMA) on mechanical properties of ABS/polycarbonate (PC) blends at ABS-rich compositions were studied. As the content of PC was increased, impact strength and Vicat softening temperature (VST) were increased. As the melt viscosity of ABS was increased near to that of PC, finer distribution of dispersed PC phase and consequent enhanced impact strength and VST were observed. The compatibilizing effect of PMMA can be ascer-tained from the enhanced properties of ¼-inch notch impact strength, VST, tensilestrength, and the morphology observed by a scanning electron microscope. The improved adhesion of the ABS/PC interface by PMMA changed the fracture mechanism and reduced the notch sensitivity of blends. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 533–542, 1998     

ACR中壳层PMMA相对分子质量对PVC／ACR共混物性能的影响

采用种子乳液法制备了核壳型聚丙烯酸酯(ACR),并分别采用十二烷基硫醇和正辛基硫醇作为链转移剂对 ACR壳层的聚甲基丙烯酸甲酯(PMMA)进行相对分子质量调节,并用于PVC共混改性。黏度法对PMMA的相对分子质量测定表明,正辛基硫醇的相对分子质量调节能力较强。采用差示扫描量热分析测定PMMA的玻璃化转变温度(Tg),并对共混树脂进行动态力学性能测试。当ACR壳层PMMA平均相对分子质量低于12×104时,PVC/ACR 共混树脂的缺口冲击强度大大提高。与纯PVC相比,共混树脂的Tg均略有提高,其增量随ACR壳层PMMA平均相对分子质量的降低而减小。动态力学性能测试结果表明,ACR壳层聚合物平均相对分子质量越低,共混物分子链段运动活化能提高越少。     

Effects of annealing in ABS ternary blends

Acrylonitrile-butadiene-styrene terpolymer (ABS)/poly(methyl methacrylate) (PMMA) binary and ABS/PMMA/polycarbonate (PC) ternary blends were prepared using a corotating twin-screw extruder. Blend samples were annealed in a constant-temperature (215 and 225°C) hydraulic press up to 85 min. The changes in morphology and mechanical properties with annealing time were studied with transmission electron microscopys image analyzer, and tensile tester. With the increase in annealing time, the number of dispersed domains per cross-sectional area decreased and average domain size increased; this morphology coarsening became more responsible with time for the deterioration of blend properties. In ABS/PMMA/PC ternary blends, PMMA encapsulated PC in ABS matrix; this was predictable from the spreading coefficient calculation. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 66: 1531–1542, 1997     

Pultruded fiber-reinforced poly(methyl methacrylate) composites. II. Static and dynamic mechanical properties,environmental effect,and postformability

This paper presents a novel process developed to manufacture poly(methyl methacrylate) (PMMA) pultruded composite. The mechanical, thermal, and dynamic mechanical properties, environmental effect, postformability of various fiber (glass, carbon, and Kevlar 49 aramid fiber) reinforced pultruded PMMA composites have been studied. Results show mechanical properties (i.e., tensile strength, specific tensile strength, tensile modulus, and specific flexural strength) and thermal properties (HDT) increase with fiber content. Kevlar fiber/PMMA composites possess the highest specific tensile strength and HDT, carbon fiber/PMMA composites show the highest tensile strength and tensile modulus, and glass fiber/PMMA composites show the highest specific flexural strength. Pultruded glass-fiber-reinforced PMMA composites exhibit good weather resistance. These composite materials can be postformed by thermoforming under pressure, and mechanical properties of postformed products can be improved. The dynamic shear storage and loss modulus (G′, G″) of pultruded glass-fiber-reinforced PMMA composites increased with decreasing pulling rate, and their shear storage moduli are higher than those of pultruded Nylon 6 and polyester composites.