An experimental matrix design to optimize the weldline strength in injection molded parts

The forming of weldlines wherever polymer flow fronts meet is one of the problems that confound the overall success of injection molding technology. In this study, an L'18 experimental matrix design based on the Taguchi method was conducted to optimize the weldline strength of injection molded thermoplastics. Experiments were carried out on a 4.1 oz injection molding machine. A plate cavity with an obstacle at the center was used to create a weldline. After molding, the weldline strength of the parts was measured with a tensile tester. Of the factors selected in the main experiments, melt temperature and mold temperature were found to be the principal factors affecting the weldline property of injection molded thermoplastics. Weldline strengths of injection molded parts increase with the size of the obstacles.     

Fatigue performance of injection‐molded short e‐glass fiber reinforced polyamide‐6,6. II. Effects of melt temperature and hold pressure

Tensile and fatigue properties of an injection molded short E‐glass fiber reinforced polyamide‐6,6 have been studied as a function of two key injection molding parameters, namely melt temperature and hold pressure. It was observed that tensile and fatigue strengths of specimens normal to the flow direction were lower than that in the flow direction, indicating inherent anisotropy caused by injection molding. Tensile and fatigue strengths of specimens with weld line were significantly lower than that without weld lines. For specimens in the flow direction, normal to the flow direction and with weld line, tensile strength and fatigue strength increased with increasing melt temperature as well as increasing hold pressure. The effect of specimen orientation on the tensile and fatigue strengths is explained in terms of the difference in fiber orientation and skin‐core morphology of the specimens. POLYM. COMPOS., 2011. © 2010 Society of Plastics Engineers.     

Effect of process conditions on the weld‐line strength and microstructure of microcellular injection molded parts

This study was aimed at understanding how the process conditions affect the weld‐line strength and microstructure of injection molded microcellular parts. A design of experiments (DOE) was performed and polycarbonate tensile test specimens were produced for tensile tests and microscopic analysis. Injection molding trials were performed by systematically adjusting four process parameters (i.e., melt temperature, shot size, supercritical fluid (SCF) level, and injection speed). For comparison, conventional solid specimens were also produced. The tensile strength was measured at the weld line and away from the weld line. The weld‐line strength of injecton molded microcellular parts was lower than that of its solid counterparts. It increased with increasing shot size, melt temperature, and injection speed, and was weakly dependent on the supercritical fluid level. The microstructure of the molded specimens at various cross sections were examined using scanning electron microscope (SEM) and a light microscope to study the variation of cell size and density with different process conditions.     

Morphological development during injection molding of self‐reinforcing composites. I: Experimental results

The correlation between structure development during injection molding and the modulus of injection molded PET/LCP blends were studied. Process parameters such as injection speed and mold and melt temperatures were varied to determine the effect of these parameters on the tensile modulus and structure development of the blends. The skin/core structure in the cross section of injection molded samples was observed with both optical and scanning electron microscopy techniques. Injection molding experiments show that the thickness of the skin layer increases with decreasing injection speed and decreasing melt and mold temperatures. The trends in morphological developments in the injection molded specimens correlate with the measured tensile moduli.     

Localized effects of dynamic melt manipulation on flow induced orientation and mechanical performance of injection molded products

This study investigates the effects that dynamic melt manipulation based injection molding has on the locally induced molecular orientation and tensile strength of injection molded polystyrene. Melt manipulation refers to a process where the polymer melt is manipulated during molding beyond the extent normally encountered in conventional injection molding. The specific melt manipulation process investigated in this article is vibration assisted injection molding, where a conventional injection molding machine is augmented by oscillating the injection screw (in the axial direction) during the injection and packing phases of the molding cycle. The localized final molecular orientation and morphology that results dictates the resultant product response, and typically improved mechanical properties are observed. Specimens with molecular orientation distributed more uniformly along the gage length typically exhibited higher tensile strength than samples with a gradient of orientation along the gage length. Smaller test specimens machined along the gage length of larger molded specimens showed dramatic tensile strength increase in the regions of higher melt manipulation, further supporting the promise of this novel processing methodology. POLYM. ENG. SCI., 47:1912–1919, 2007. © 2007 Society of Plastics Engineers     

Experimental Results of Low Thermal Inertia Molding. I. Length of Filling

In injection molding, complete mold cavity filling is a design goal that has to be met 100% every time. Mold cavity filling is a complicated process which depends on many variables such as mold cavity surface temperature, injection pressure, injection speed, melt temperature, flow index of material being molded, etc. The aim of experimental investigation of the low thermal inertia molding (LTIM) [1] process is to demonstrate the feasibility of molding completely filled, thin parts at low injection pressure and injection speed without sacrificing part quality. The evaluation of the new molding concept consists of comparison of a conventionally molded thin rectangular part with an identical part molded by the LTIM process. The length of filling in the conventional cavity and in the LTIM cavity are compared at different injection pressures and injection speeds. The mold design, experimental procedure, and results of the molding are discussed in the following sections.     

注射成型工艺条件对聚丙烯制品光泽度的影响

通过一次因子法确定了Taguchi法的试验因子,采用Taguchi法对试验因子进行权重分析与优化,并进一步研究了注射成型工艺条件对聚丙烯制品光泽度的影响。结果表明,在注射成型过程中,提高熔体温度、模具温度、保压压力及注射速率都有助于提高制品的光泽度,同时也会提高制品的拉伸强度和弯曲强度,但会降低缺口冲击强度。影响聚丙烯制品光泽度的最显著因素是熔体温度。影响因子的权重大小顺序为：熔体温度、模具温度、保压压力、注射速率。     

Effects of geometry and injection‐molding parameters on weld‐line strength

Polymeric flows in microchannels are found to differ significantly from those in macrogeometries. Increasing the mechanical properties of microstructures is one of the most important issues in injection‐molding processes. Weld‐line characteristics of structures with different cross‐sections are investigated in this study. The effects of process parameters and cross‐sectional dimensions on the tensile strength of a weld line are discussed. A mold was designed in such a way that specimens with and without weld lines can be developed separately. Five specimens, with different cross‐sections, are injection‐molded simultaneously. Both polypropylene (PP) and high density polyethylene (HDPE) are used in this study. With the Taguchi method, four process variables: melt temperature, mold temperature, injection speed, and packing pressure were found to be the most influential. Experimental results show that the weld‐line strength from a standard test is not applicable in microinjection molding. The microstructure of weld lines is clearly observed from the micrographs. POLYM. ENG. SCI., 45:1021–1030, 2005. © 2005 Society of Plastics Engineers     

Processing-property relationships in compression molding of sheet molding compounds

An experimental investigation was conducted into establishing relationships between the processing variables and the mechanical properties of compression-molded parts of sheet molding compounds (SMC). Emphasis was placed on investigating the effects on the tensile properties, impact strength, and dynamic mechanical properties of composite specimens, of low-profile additives, and of treating glass fibers (for reinforcement) with sizing chemicals. The processing variables investigated were cure time, mold temperature, and mold pressure. It was found that: (1) An optimum cure time and mold temperature exist for achieving molded SMC composites of the greatest tensile and impact strengths; (2) Of the four different types of low-profile thermoplastic additives employed, the poly(vinyl acetate) modified with acrylic acid gives rise to molded SMC composites having the greatest tensile and impact strengths; (3) An optimum cure time and mold temperature exist for achieving the highest glass-transition (T_g) of the low-profile additive; (4) The values of cure time and mold temperature that have yielded the greatest tensile and impact strengths also yield molded specimens having the highest T_g of the low-profile additive.     

模具结构和熔体温度对PC透明制品性能的影响

用光弹实验测试不同浇口类型、不同熔体温度下聚碳酸酯透明注塑制品的应力分布,并测试了制品的拉伸强度和透光率。研究发现,模具结构对残余应力的分布形式影响显著,高应力区的拉伸强度较低,相对于无应力区最高降幅达2.69MPa;在同一成型条件下扇形浇口试样的透光率普遍要高于潜伏式浇口试样;熔体温度对试样的残余应力分布影响不大,但随着温度的升高,拉伸强度缓慢提高;要满足最佳透光率效果,不同模具结构的试样成型温度不同,试样的透光率最高达89.93%,浇口高应力区的透光率明显较低。     

Self‐interference flow of an isotactic polypropylene melt in a cavity during injection molding. I. Effect of the self‐interference flow on the properties

The self‐interference flow (SIF) of a melt in a cavity during injection molding is introduced. It comes from two streams of the melt being split by a patented mold gate called a twin gate. The effects of this flow on the static and dynamic mechanical properties, thickness distribution, and shrinkage in the transverse direction (TD) of injection‐molded isotactic polypropylene parts are discussed. SIF has an influence on the static mechanical properties, especially the impact strength. There are slight increases in the tensile strength and Young's modulus and an increase of approximately 70–90% in the impact strength in comparison with the properties of samples obtained by a conventional flow process with a common pin gate. Dynamic mechanical thermal analysis studies show an increase in the storage modulus for SIF samples. Results obtained from research into the effect of the mold temperature and injection pressure on the impact strength show that the impact strength of SIF specimens has a weaker dependence on the mold temperature and injection pressure. In addition, the flow brings a more uniform thickness distribution and a smaller shrinkage in the TD to SIF samples. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2784–2790, 2003     

Effect of molecular weight and molding conditions on the replication of injection moldings with micro‐scale v‐groove features

Injection molded optical plastic parts require accurate replication of micro‐scale features. The effects of melt viscosity and molding conditions on replication of microscopic v‐groove features in injection molded parts were examined for PC with different molecular weight. The micro‐scale feature size was a continuous v‐groove with 20 μm in depth and 50 μm in width. For injection molding conditions, melt temperature, mold temperature, injection velocity and holding pressure were varied in three levels. As the result, the mold temperature had significantly affected replication for all polymers with different molecular weight. Additionally, the molding conditions that lower melt viscosity led to improved replication. In the case of polymer with high molecular weight, the viscosity decreased with increasing melt temperature. It has been found that high replication of micro‐scale features could be achieved by higher mold temperature and higher melt temperature even with high viscosity PC. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

The effect of injection molding process parameters on mechanical and fracture behavior of polycarbonate polymer

In this work, the mechanical and failure behavior of injection molded aviation standard optical grade polycarbonate (PC) was investigated through uniaxial tensile testing. The effect of different injection molding process parameters including injection velocity, packing pressure, cooling time, mold temperature, and melt temperature were determined to observe their effect on yield and postyield behavior of PC. Out of these examined parameters, the mold and melt temperature show significant effect on mechanical behavior of studied polymer. The yield and flow stresses in polymer increase with the increase in mold and melt temperature during injection molding. However, other process parameters i.e., packing pressure, injection velocity, and cooling time showed little effect on mechanical performance of the polymer. The molded specimens were annealed at different temperatures and residence time to evaluate its effect on mechanical behavior and fracture morphology. The yield stress increases gradually with the increase in annealing temperature and time. The annealing treatment also changed the failure mode of PC specimens from ductile to brittle. In addition to process parameters, the effect of increased loading rate was also undertaken which shows substantial effect on mechanical and failure behavior of PC. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44474.     

The influence of injection molding parameters and blowing agent addition on selected properties,surface state,and structure of HDPE parts

The investigation of the influence of injection molding parameters (injection velocity, mold temperature and injection temperature, and additionally, as a result of these three parameters change, injection time, hold time, and cooling time) and blowing agent percentage on selected properties of HDPE molded parts such as weight, density, mechanical properties (tensile strength and elongation at maximum force), surface state (gloss and color), and structure was the aim of this work. The examination showed, that the mold temperature has the main influence on properties and surface state of molded parts from solid and foam HDPE. The weight, density, mechanical properties and gloss of molded parts increased with the increase in mold temperature. The mold temperature also influences significantly the number and size of pores in molded parts. The addition of blowing agent in a quantity of 2% is sufficient to obtain parts with favorable mechanical properties and good surface quality. POLYM. ENG. SCI., 2013. © 2012 Society of Plastics Engineers.     

Weldline strength in injection molded HDPE/PA6 blends: Influence of interfacial modification

Most injection molded objects contain defects known as weldlines. This defect may introduce an element of weakness affecting the object's performance. Weldlines are particularly problematic in multiphase materials where the situation may be exaggerated by component mismatch on the two sides of the interface that results in additional weakening when the two components do not adhere well to each other. In addition, weldline behavior is influenced by orientation and morphological effects. This paper deals with relationships between the structure and the mechanical properties in injection molded high density polyethylene polyamide-6 blends. The weldline effect is investigated in detail. Two molds were used to generate weldlines: a double-gated tensile bar cavity in which the weldline results from the meeting of two melt fronts flowing into each other from opposite directions, and a film-gated rectangular plaque mold with a circular insert that divides the melt front in two. Following the recombination of the fronts, there is additional flow as the melt fills the mold cavity. Two preparations containing 75 vol % of polyamide-6 and 25 vol % of polyethylene with and without compatibilizer were studied. In the first case, a compatibilizer was incorporated into the polyethylene prior to compounding with the polyamide-6. In the directly molded tensile bar the minor phase is strongly oriented parallel to flow. Only in the core, which represents about 10% of the sample thickness, do the dispersed phase particles assume spherical shape. The morphology of the weldline is closely related to that of the skin: the elongated structures are oriented parallel to the weldline plane. The effect of the compatibilizer on the mechanical properties (without the weldline) of the directly molded tensile bars is minor: It is overshadowed by the flow-induced morphology. The weldline strength loss is about 40% in the noncompatibilized blend. The introduction of the compatibilizer has restored the material's ability to yield and the properties are close to those measured without the weldline. For the second type mold, the effect of the weldline is less pronounced and the effect of the distance from the insert is negligible. The anisotropy is quite pronounced in the noncompatibilized blend. In compatibilized blends, all tensile properties are unaffected by the presence of weldline, except for the 2-mm-thick plaque in the position close to the insert. The properties in the direction parallel to flow are similar to the type I mold and not affected by the increase of plaque thickness. Consequently one may question the utility of the directly molded tensile specimens in studying various aspects of the mechanical behavior of multiphase materials where the flow-generated structure is very different from that found in “real” injection molded parts. © 1995 John Wiley & Sons, Inc.     

INCREASING FLOW LENGTH IN THIN WALL INJECTION MOLDING USING A RAPIDLY HEATED MOLD

Injection molded parts are driven down in size and weight especially for portable electronic applications. While gains are achieved via cost reduction and increased portability, thinner parts encounter more difficulty in molding due to the frozen layer problem. To increase moldability in thin wall molding, a rapid thermal response (RTR) mold was investigated. The RTR mold is capable of rapidly raising the surface temperature to the polymer melt temperature prior to the injection stage and then rapidly cooling to the ejection temperature. The resulting filling process is done inside a hot mold cavity and formation of frozen layer is prohibited. Concepts of scalable filling and low-speed filling are discussed in the article to address the benefit of this molding method. Simulation results showed that significant reduction in injection pressure and speed can be achieved in RTR molding. In contrast to the filling behavior in conventional molding, the injection pressure in RTR molding decreases as the injection speed decreases, and therefore, extremely thin parts can be molded at lower injection speeds. Filling lengths of both RTR and conventionally molded polycarbonate samples, with two levels of thickness, under two levels of injection speed were experimentally studied. The experimental results demonstrated the advantage of the new molding method.     

Effects of processing conditions on birefringence development in injection molded parts. II. Experimental measurement

The birefringence of injection molded parts was measured using a digital photoelasticity system, which combines a digital image analysis technique and the half-fringe photoelasticity (HFP) method The effects of processing conditions, including melt temperature, mold temperature, filling time and packing pressure, on the birefringence development in the molded parts were investigated. It was found that temperature and pressure are the two dominant factors that determine the birefringence development in the parts during the molding process. Frozen-in birefringence of the molded parts decreases with increasing melt temperature, mold temperature and injection speed. Birefringence of the parts also increases with increased packing pressure, especially around the gate area. Numerical simulations using the Leonov viscoelastic fluid model predict similar dependence of birefringence of parts on processing conditions. Simulated results are also consistent with measured values.     

Performance prediction of weldline structure in amorphous polymers

The presence of a weldline generally reduces the mechanical strength of injection molded parts. A typical remedy to eliminate the problem of weak weldline structure has been to increase the melt temperature. This, however, is not an acceptable solution in some situations. A general solution to the weak weldline problem requires an in-depth understanding of the thermomechanical history of the injection molding process. A theoretical model for the strength of weldlines is presented that provides a comprehensive physical insight of the bonding process at the weldline interface. The model is based on the self-diffusion of molecular chains across the polymer-polymer interface and the frozen-in orientation that remains parallel to the interface. Both factors are analyzed separately and then superimposed to predict the strength of weldlines from known processing conditions and geometry. Experimental results show good correlation with predictions.     

Effects of nozzle length on mold filling simulation accuracy

A common assumption in mold filling analysis is that the molding machine is capable of providing a fully pressurized uniform temperature melt to the rear orifice of the sprue. Based upon this assumption, the finite element model then only represents the geometry of the mold itself from the sprue rear orifice forward. This assumption, however, is acceptable only when the injection modeling machine nozzie extension is of such a length that the pressure drop in the nozzle is negligible. For large injection molded parts the exclusion of the molding machine nozzle in the design phase of the mold filling analysis may produce overly optimistic results. This study of an actual large (7.9 kg) injection molded thin wall (4 mm) vinyl part will show the effects of nozzle length on the accuracy of mold filling analysis software predictions. Analytical results with and without representation of the molding machine nozzle in the finite element model will be compared to production trial results.