Influence of interfacial adhesion on the structural and mechanical behavior of PP‐banana/glass hybrid composites

Hybrid composites of polypropylene (PP), reinforced with short banana and glass fibers were fabricated using Haake torque rheocord followed by compression molding with and without the presence maleic anhydride grafted polypropylene (MAPP) as a coupling agent. Incorporation of both fibers into PP matrix resulted in increase of tensile strength, flexural strength, and impact strength upto 30 wt% with an optimum strength observed at 2 wt% MAPP treated 15 wt% banana and 15 wt% glass fiber. The rate of water absorption for the hybrid composites was decreased due to the presence of glass fiber and coupling agent. The effect of fiber loading in presence of coupling agent on the dynamic mechanical properties has been analyzed to investigate the interfacial properties. An increase in storage modulus (E′) of the treated‐composite indicates higher stiffness. The loss tangent (tan δ) spectra confirms a strong influence of fiber loading and coupling agent concentration on the α and β relaxation process of PP. The nature of fiber matrix adhesion was examined through scanning electron microscopy (SEM) of the tensile fractured specimen. Thermal measurements were carried out through differential scanning calorimetry (DSC) and the thermogravimetric analysis (TGA), indicated an increase in the crystallization temperature and thermal stability of PP with the incorporation of MAPP‐treated banana and glass fiber. POLYM. COMPOS., 31:1247–1257, 2010. © 2009 Society of Plastics Engineers     

Composition,tensile properties,and dispersion of polypropylene composites reinforced with viscose fibers

The reinforcement mechanics of viscose‐fiber‐reinforced polypropylene (PP) composites were studied. The effect of the coupling agent, maleated polypropylene (MAPP), was of special interest. The fibers, coupling agent, and PP were extruded and injection‐molded. The composition, mechanical properties, fracture morphology, and dispersion of the composites were examined. Thermogravimetric analysis showed that the fiber content in the tensile specimens varied slightly with the sample location; however, the differences in the values were within 1.0%. Scanning electron microscopy images of the fracture surfaces of the composites showed that the surfaces of the composites without MAPP were covered with fibers pulled out from the matrix. A lack of adhesion further appeared as a cracked matrix–fiber interface. A new scanning thermal microscopy method, microthermal analysis, was used to study the dispersion of the fibers in the composites. Local thermal analyses gave further information about the location of the fibers. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2676–2684, 2004     

Mechanical,thermal and dynamic‐mechanical behavior of banana fiber reinforced polypropylene nanocomposites

Natural fiber‐reinforced nanocomposites based on polypropylene/nanoclay/banana fibers were fabricated by melt mixing in a twin‐screw extruder followed by compression molding in this current study. Maleic anhydride polypropylene copolymer (MA‐g‐PP) was used as a compatibilizer to increase the compatibility between the PP matrix, clay, and banana fiber to enhance exfoliation of organoclay and dispersion of fibers into the polymer matrix. Variation in mechanical, thermal, and physico‐mechanical properties with the addition of banana fiber into the PP nanocomposites was investigated. It was observed that 3 wt% of nanoclay and 5 wt% of MA‐g‐PP within PP matrix resulted in an increase in tensile and flexural strength by 41.3% and 45.6% as compared with virgin PP. Further, incorporation of 30 wt% banana fiber in PP nanocomposites system increases the tensile and flexural strength to the tune of 27.1% and 15.8%, respectively. The morphology of fiber reinforced PP nanocomposites has been examined by using scanning electron microscopy and transmission electron microscopy. Significant enhancement in the thermal stability of nanocomposites was also observed due to the presence of nanoclay under thermogravimetric analysis. Dynamic mechanical analysis tests revealed an increase in storage modulus (E′) and damping factor (tan δ), conforming the strong interaction between nanoclay/banana fiberand MA‐g‐PP in the fiber‐reinforced nanocomposites systems. POLYM. COMPOS., © 2011 Society of Plastics Engineers.     

Optimal performances of ultrasound treated kenaf fiber reinforced recycled polypropylene composites as demonstrated by response surface method

Kenaf fiber (KF) reinforced recycled polypropylene (RPP) composites were produced by melt cast method. To improve interfacial adhesion between fiber and RPP matrix, fiber surface modification was carried out by means of ultrasound treatment. Maleic anhydride grafted polypropylene (MAPP) was used as a coupling agent. Composites were examined by mechanical test, melt flow indexing test, scanning electron microscopy, thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). Water uptake analysis and accelerated weathering test were carried out to find the suitability of the composites in outdoor application. Among the raw fiber contents ranging 10?50 wt % in the composites, the maximum tensile strength (TS) was observed at 40 wt % KF loading without using MAPP. Treated KF‐based composite with MAPP promotes this maximum TS value, which is 57% higher than that of raw KF‐based composite. TGA and DSC analyses exhibit an enhancement of thermal stability in treated KF‐reinforced RPP composites with MAPP. Incorporation of MAPP in the composites shows higher activation energy, suggesting improved interfacial bonding between fibers and matrix. Response surface method was employed to demonstrate the optimal treatment parameters for TS, showing excellent agreement with the observed values. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Rheological characterization of PP/jute composite melts

The present article summarizes an experimental study on the molten viscoelastic behavior of PP/jute composites under steady and dynamic mode. Variations in melt viscosity and die swell of the composites with an increase in shear rate, fiber loading, and coupling agent concentration have been investigated using capillary rheometer. It was observed that with the addition of fibers and MAPP, the melt viscosity of the composites increased due to improved fiber‐matrix interfacial adhesion. Further, the dynamic viscoelastic behavior, measured using parallel plate rheometer, revealed an increase in the storage modulus (G′), indicating higher stiffness in case of fiber‐filled composites as compared with the virgin matrix. Time–temperature superposition was applied to generate various viscoelastic master curves. The fiber‐matrix morphology of the extrudates was also examined using scanning electron microscopy, which corroborated the findings of rheological properties. The treated composites displayed uniform distribution of fibers within the PP matrix with lesser surface irregularities. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1476–1484, 2006     

Isolation and characterization of betel nut leaf fiber: Its potential application in making composites

Betel nut leaf fiber (BNLF) is a new finding as cellulosic filler for polymer composites. Its main constituents are 75% α‐cellulose, 12% hemicelluloses, 10% lignin, and 3% others matter, viscosity average molecular weight 132,000 and degree of crystallinity 70%. In the present work, BNLF reinforced polypropylene (PP) composites were prepared using heat press molding method. 5–20 wt% short length fiber is taken for getting benefits of easy manufacturing and the fiber was chemically treated with NaOH, dicumyl peroxide (DCP), and maleic anhydride‐modified PP (MAPP) to promote the interfacial bond with PP. The extent of modification of fiber was assessed on the basis of morphology, bulk density, moisture absorption, thermal, and mechanical properties of untreated fiber, treated fiber, and their reinforcing PP composites. The tensile and flexural strength of composites increase with the increase of fiber loading up to 10 and 20 wt%, respectively. It was also observed that Young's modulus and flexural modulus increase with fiber loading. The thermal degradation behavior of resulting composites was investigated. Among the various treated fibers, MAPP‐treated fiber composite showed best interfacial interactions as well as mechanical and thermal properties. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Influence of fiber surface treatment on mechanical performance of Xanthoceras sorbifolia bunge husk fibers/PP composites

The PP Composites containing Xanthoceras sorbifolia Bunge husks fibers with different surface treatments were prepared. The mechanical properties such as tensile properties and impact properties of the composites were investigated. It is revealed that the composites with fibers treated by alkali and the following treatments of silane coupling agents KH570, titanate coupling agent JN‐9A, acetic anhydride, MAPP, or bleach, all performed higher in tensile properties than that with untreated fibers, while lower in impact properties. Meanwhile, all treated fibers performed better thermal stability than untreated fibers. The fibers treated by alkali followed by KH570 treatment were added into PP with different contents. It is found that as the fiber content increases, the elastic modulus and impact strength of the composites increase sharply at first followed by a decrease, while the tensile strength decrease initially and increase with a peak at 10%, then decrease continuously. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41217.     

Influence of maleated polypropylene on mechanical properties of composite made of viscose fiber and polypropylene

The purpose of this work was to study how viscose fiber behaves in polypropylene (PP) matrix when maleated polypropylene (MAPP) is used as a coupling agent. The influences of processing conditions on composite properties was of interest. Composites were characterized by FTIR and mechanical testing. The most notable result was the effect of the MAPP concentration on the tensile strength of the composites; the tensile strength increased from 40 to 69 MPa when MAPP was added in amounts up to 6 wt % of the fiber weight. The interaction between MAPP and fiber was confirmed with FTIR. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 87: 1895–1900, 2003     

Preparation and characteristics of composites of high‐crystalline cellulose with polypropylene: Effects of maleated polypropylene and cellulose content

Binary composites of high‐crystalline fibrous cellulose with polypropylene (PP) or maleic anhydride‐grafted polypropylene (MAPP) were prepared by melt‐mixing with different contents of cellulose from 0 to 60 wt %. Ternary composites of cellulose with PP and MAPP were also prepared to investigate the effects of MAPP as a compatibilizer between cellulose and PP. Scanning electron microscopy revealed that the addition of MAPP generates strong interactions between a PP matrix and cellulose fibers: All cellulose fibers are encapsulated by layers of the matrix and connected tightly within the matrix. Thus, the tensile strength and Young's modulus of MAPP‐containing composites increase with an increase in MAPP and cellulose content, in contrast to the decrease in tensile strength of a PP‐based binary composite with an increase in cellulose. Cellulose fibers act as a nucleating agent for the crystallization of PP, which is promoted by the addition of MAPP through an increase of the crystallization temperature of PP in the composite. Accordingly, both cellulose and MAPP facilitate the thermooxidative stability of PP composites in the following order: MAPP/cellulose > PP/MAPP/cellulose > PP/cellulose > PP. Relative water absorption increases with an increase in cellulose content, decreasing with the addition of MAPP. MAPP‐containing cellulose composites have high potential for applications as environmentally friendly materials. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 337–345, 2003     

香蕉纤维的表面改性及其增强环氧树脂复合材料的性能研究

采用硅烷偶联剂(A-174)偶联、高锰酸钾接枝和乙酰化包覆等3种方法对香蕉纤维进行表面改性,制备了改性香蕉纤维增强环氧树脂复合材料,测试其拉伸、弯曲、压缩、冲击等力学性能。结果表明,偶联、接枝、包覆等表面改性均能明显改善香蕉纤维与基体树脂的相容性,提高复合材料的力学性能,其中偶联改性的效果最好。当改性香蕉纤维含量为10wt%时,与未改性的香蕉纤维比较,复合材料的拉伸强度、弯曲强度、压缩强度分别提高了1.8、1.0、2.6倍;随着纤维含量的增加,复合材料的力学性能明显提高。     

Banana fiber reinforced low-density polyethylene composites: effect of chemical treatment and compatibilizer addition

In this study, an attempt has been made to utilize banana fiber (a natural fiber from agricultural waste) as reinforcement for low-density polyethylene (LDPE) to develop environmental friendly composite materials. LDPE/banana fiber composites were fabricated at different fiber loadings (10, 15, 20, 25, and 30 wt %) using compression molding technique. The composite with the composition of 25 wt % banana fiber was observed to be optimum on the basis of biodegradability and mechanical properties. Further, the effect of banana fiber surface treatment (alkali and acrylic acid) on the mechanical properties, morphology and water absorption behavior of the LDPE/banana fiber composites in the absence and presence of compatibilizer (maleic anhydride grafted LDPE, MA-g-LDPE) was comparatively studied. The alkali and acrylic acid treatment of the banana fibers led to enhanced mechanical properties and water resistance property of the composites, and these properties got further improved by the addition of the compatibilizer. The addition of compatibilizer to the acrylic acid treated banana fiber composites showed the most effective improvement in the flexural and impact strength and also, exhibited a reduction in the water absorption capacity. However, the tensile strength of the compatibilized composites with treated fibers resulted in slightly lower values than those with untreated fibers, because of the degradation of fibers by chemical attack as was evidenced by scanning electron microscopy (SEM) micrographs. SEM studies carried out on the tensile fractured surface of the specimens showed improved fiber-matrix interaction on the addition of compatibilizer.     

Effects of silane coupling agent and maleic anhydride‐grafted polypropylene on the morphology and viscoelastic properties of polypropylene–mica composites

In this study, morphology, and dynamic and mechanical properties of polypropylene–mica (PP–Mica) composites were investigated. To enhance the adhesion between PP and mica, maleic anhydride‐grafted PP (MAPP) and treated mica with silane coupling agent were used. MAPP (as a compatibilizer) and silane coupling agent (as a filler surface modifier) caused an interfacial bonding in the mica filled polypropylene composites. The effect of mica content, MAPP, and treated mica with silane coupling agent on the morphological properties were investigated by Scanning Electron Microscopy (SEM). The results showed that with increasing MAPP or silane coupling agent, dispersion of filler and adhesion between PP and filler were improved. Mechanical data showed that with increasing MAPP and mica treated with silane coupling agent, tensile modulus and flextural strength of composites were enhanced. Dynamic rheological behavior of composites was also investigated within the domain of linear viscoelasticity. The rheological observations indicated that the complex viscosity, storage and loss moduli increased, and tan δ decreased with increasing mica content. POLYM. COMPOS. 27:491–496, 2006. © 2006 Society of Plastics Engineers.     

Unidirectional hemp and flax EP‐ and PP‐composites: Influence of defined fiber treatments

In some technical areas, mainly in the automotive industry, glass fiber reinforced polymers are intended to be replaced by natural fiber reinforced polymer systems. Therefore, higher requirements will be imposed to the physical fiber properties, fiber‐matrix adhesion, and the quality assurance. To improve the properties of epoxy resins (EP) and polypropylene (PP) composites, flax and hemp fibers were modified by mercerization and MAH‐PP coupling agent was used for preparing the PP composites. The effects of different mercerization parameters such as concentration of alkali (NaOH), temperature, and duration time along with tensile stress applied to the fibers on the structure and properties of hemp fibers were studied and judged via the cellulose I–II lattice conversion. It was observed that the mechanical properties of the fibers can be controlled in a broad range by using appropriate mercerization parameters. Unidirectional EP composites were manufactured by the filament winding technique; at the PP matrix material, a combination with a film‐stacking technique was used. The influence of mercerization parameters on the properties of EP composites was studied with hemp yarn as an example. Different macromechanical effects are shown at hemp‐ and flax‐PP model composites with mercerized, MAH‐PP‐treated, or MAH‐PP‐treated mercerized yarns. The composites' properties were verified by tensile and flexural tests. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2150–2156, 2004     

Mechanical properties and water absorption of fiber‐reinforced polypropylene composites prepared by bagasse and beech fiber

The present study investigates the tensile, flexural, notched Izod impact, and water absorption properties of bagasse and beech reinforced polypropylene (PP) composites as a function of fiber content. The surface of fibers was modified through the use of maleated polypropylene (MAPP) coupling agent. From this study, it was found that mechanical properties increase with an increase in fiber loading in both cases. However, the addition of wood fibers resulted in a decrease in impact strength of the composites. The water absorption property at varying fiber loading was evaluated and found maximum for the BA/PP composites. The weight gains for all specimens were less than 7%. In general, the results showed the usefulness of bagasse fiber as a good alternative and reinforcing agent for composite. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Fundamental studies on wood–plastic composites: Effects of fiber concentration and mixing temperature on the mechanical properties of poplar/PP composite

Wood fibers are increasingly being used as reinforcement in commercial thermoplastic composites due to their low cost, high specific properties and renewable nature. The ultimate goal of our research was to find a fundamental understanding of the mechanical behavior of poplar/polypropylene (PP) composites. The effect of wood fiber concentrations and mixing temperature on the mechanical properties of composites, prepared by using MAPP as the coupling agent, was investigated. In the sample preparation, four levels of fiber loading (10, 20, 30, and 40 wt%) and three compounding temperatures (180, 190, and 200^oC) were used. Most major changes in composite performance occurred at fiber contents above 30%. The results clearly showed that the fiber loading of 30 and 40 wt% at 190^oC was provided adequate reinforcement to increase the tensile and flexural strength of the PP powder. The modulus also increased with increasing the fiber content, because poplar fibers are believed to be more rigid than polymer. However the addition of wood fibers resulted in a decrease in elongation and impact properties of the composites. The FTIR spectroscopy showed that the copolymer was bonded to the fibers by ester linkages and hydrogen bonds at 1705–1735 cm⁻¹. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers     

Silane and silazane surface modification of recycled glass fibers for polypropylene composites

Glass fiber (GF) composites are one of the significant challenges in recycling thermoset materials. After pyrolysis, the glass fibers lack sufficient strength and show poor matrix compatibility. Here we have investigated a series of multifunctional silane and silazane agents for surface modification of recycled glass fibers that provide a combination of hydrophobic properties and residual reactive groups on the surface. This allowed testing of interfacial effects from the surface modification as well as a potential synergistic compatibilization using maleated PP (MAPP). The treated GFs were used to prepare new polypropylene (PP) composites by multiple extrusion steps, resulting in a series of composites where the dispersion efficiency was attributed mainly to the surface chemistry and compatibilization effects. The amino-silane modifications of the recycled fibers resulted in further improvements in the mechanical properties of the PP composites in comparison with the hydrophobized GFs. Moreover, synergistic effects from the addition of MAPP were observed with scanning electron microscopy. The results clearly demonstrate that the surface modifications were effective and good alternatives to currently used methods.     

Poly(propylene)/poly(ethylene terephthalate‐co‐isophthalate) blends and glass bead filled composites: Microstructure and thermomechanical properties

Blends of poly(propylene) (PP) and poly(ethylene terephthalate‐co‐isophthalate) (co‐PET) (95/5) with and without compatibilizing agent (maleic anhydride PP), as well as composites of these blends with glass beads (50 wt%) with and without silane coupling agent surface‐treatment, were prepared and studied on a basis of the material microstructure and thermomechanical properties. Infrared and Raman spectroscopy, as well as transmission electron microscopy, displayed evidence of MAPP compatibilizing action for the blend. Differential scanning calorimetry showed a remarkable effect of nucleation rate increase exerted by co‐PET on the PP crystallization. Moreover, glass beads were found to increase the PP nucleation rate slightly. PP crystallinity hardly varied with the composition. Wide angle X‐ray diffraction allowed determination of differences in the orientation of the poly(propylene) b‐axis, with more homogeneous orientations in the presence of both co‐PET and glass beads. MAPP promoted the PP b‐axis orientation. Differences in PP α′ relaxation could be analyzed through dynamic‐mechanical thermal analysis (DMTA). © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1841–1852, 2004     

Synthesis and characterization of polypropylene reinforced with cellulose I and II fibers

Recently, cellulose fiber–thermoplastic composites have played an important role in some applications. Plastics reinforced with cellulose and natural fibers have been widely studied. However, composites with regenerated cellulose have rarely been investigated. In this study, the lyocell fiber of Lenzing AG (cellulose II) and its raw material a bleached hardwood pulp (cellulose I) were used as reinforcement materials. The mechanical and thermal properties of polypropylene (PP) reinforced with pulp and lyocell fibers were characterized and compared with regard to the content of the fiber and the addition of maleated polypropylene (MAPP). PPs with cellulose I or II as a reinforcement material had similar mechanical properties. However, when MAPP was used as coupling agent, the mechanical properties of the composites were different. The crystallinity of the composites were determined by differential scanning calorimetry. Cellulose I (pulp) promoted the crystallization of PP, whereas cellulose II did not. MAPP reduced this effect in cellulose I fibers, but it induced crystallization when cellulose II (lyocell) was used as a reinforcement material. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 364–369, 2006     

Conifer fibers as reinforcing materials for polypropylene‐based composites

Conifer fibers were used to reinforce polypropylene (PP). To improve the compatibility between the conifer fibers and the PP matrix, the fibers were either grafted with maleated PP (MAPP), treated by adding MAPP, or mixed with ethylene/propylene/diene terpolymer (EPDM). The treatments resulted in improved processing, as well as improvements in the thermal and mechanical properties of the resultant composites compared with the composites filled with untreated conifer fibers. Moreover, MAPP grafting and MAPP treating displayed more obvious benefits than EPDM treating in terms of thermal properties, processing flowability, and tensile strength improvements. EPDM treating also produced more significant benefits than either MAPP grafting or MAPP treating in terms of impact strength and tensile elongation improvements. These improvements were attributed to surface coating of the fibers when EPDM was used. In addition, the effect of the concentration of the conifer fibers on the properties of the composites and the difference between MAPP grafting and MAPP treating were evaluated. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2833–2841, 2001     

High Stiffness Natural Fiber‐Reinforced Hybrid Polypropylene Composites

Abstract

Natural fibers are potentially a high‐performance non‐abrasive reinforcing fiber source. In this study, pulp fibers [including bleached Kraft pulp (BKP) and thermomechanical pulp (TMP)], hemp, flax, and wood flour were used for reinforcing in polypropylene (PP) composite. The results show that pulp fibers, in particular, TMP‐reinforced PP has the highest tensile strength, possibly because pulp fibers were subjected to less severe shortening during compounding, compared to hemp and flax fiber bundles. Maleic‐anhydride grafted PP (MAPP) with high maleic anhydride groups and high molecular weight was more effective in improving strength properties of PP composite as a compatiblizer. Coupled with 10% glass fiber, 40% TMP reinforced PP had a tensile strength of 70 MPa and a specific tensile strength comparable to glass fiber reinforced PP. Thermomechanical pulp was more effective in reinforcing than BKP. X‐ray photoelectron spectroscopy (XPS) and scanning electron microscope (SEM) were used to aid in the analysis. Polypropylene with high impact strength was also used in compounding to improve the low‐impact strength prevalent in natural fiber‐reinforced PP from injection molding.