PTT/ABS合金的相形态及力学性能研究

采用双螺杆挤出机制备了聚对苯二甲酸丙二酯(PTT)/丙烯腈-丁二烯-苯乙烯塑料(ABS)合金,研究了合金组成及增容剂环氧树脂(EP)和苯乙烯-丁二烯-马来酸酐共聚物(SBM)对合金相形态及力学性能的影响.结果表明,未加增容剂的PTT/ABS合金相畴粗大,相界面清晰,合金的拉伸强度、弯曲强度随ABS含量的增加而逐渐降低,...     

聚对苯二甲酸丙二醇酯/丙烯腈-苯乙烯-丙烯酸酯共聚物共混物的制备与性能

采用扫描电子显微镜、偏光显微镜、万能材料试验机及毛细管流变仪等对聚对苯二甲酸丙二醇酯/丙烯腈-苯乙烯-丙烯酸酯共聚物（PTT/ASA）共混物的相形态、力学性能、流变性能和热老化性能进行了研究。结果表明,PTT 和ASA具有部分相容性,当ASA含量为50 ％时,共混物中形成了双连续相;随着ASA含量的增加,共混物的断面变得更粗糙,断裂方式转变为韧性断裂,ASA的加入明显提高了共混物的缺口冲击强度,但却降低了拉伸强度;共混物熔体为假塑性流体,随着ASA含 量 增 加,熔体表观黏度升高、假塑性越明显,PTT的加工性能得到改善;PTT/ASA比PTT/丙烯腈-丁二烯-苯乙烯（ABS）共混物具有更好的耐热老化性能。     

Miscibility and thermal and mechanical properties of melt‐mixed poly(lactic acid)/poly(trimethylene terephthalate)/(methyl methacrylate)‐butadiene‐styrene copolymer blends

This study examined the miscibility and mechanical properties of melt‐mixed poly(lactic acid) (PLA), poly (trimethylene terephthalate) (PTT), and PLA/PTT blend with 5–10 phr of methyl methacrylate‐butadiene‐styrene copolymer (MBS). The isothermal crystallization kinetics of the PTT blends were analyzed by using the Avrami equation. The Differential Scanning Calorimetry (DSC) and scanning electron microscope results indicated that the miscibility of the PLA/PTT blends was improved by adding 5–10 phr of MBS. Although PLA, with the addition of 10 phr of MBS, had lower tensile strength at yield and higher breaking elongation and impact strength than pure PLA, no improvement in these mechanical properties could be observed in PLA/PTT blends. This result is explained by assuming that the crystallization of PTT at the interface favors the disentanglement of MBS from the PTT domain. J. VINYL ADDIT. TECHNOL., 2011. © 2011 Society of Plastics Engineers     

Effect of Inorganic Filler on the Crystallization,Mechanical Properties and Rheological Behavior of Poly(trimethylene terephthalate)

Poly(trimethylene terephthalate) filled with nano-CaCO₃ and ultra-fine talc was prepared by melt blending using a co-rotating twin screw extruder. The effect of these two inorganic filler on the crystallization and melting behavior, mechanical properties and rheological behavior of PTT were characterized. The DSC results indicated that both nano-CaCO₃ and ultra-fine talc exhibited heterogeneous nucleation effect on the crystallization of PTT, and more significant nucleation effect were observed in PTT/nano-CaCO₃ composite due to the smaller size and better dispersion of nano-CaCO₃ in PTT matrix. Mechanical properties study suggested that the incorporation of nano-CaCO₃ and ultra-fine talc greatly improved the tensile and flexural properties of PTT. Ultra-fine talc tends to lower the impact properties, while nano-CaCO₃ tend to increase the impact strength of the PTT/nano-CaCO₃ composite. When 2 wt.% of nano-CaCO₃ was added, the impact strength increased by one time. Rheological behavior study indicated nano-CaCO₃ exhibited plasticization effect on PTT melt and decreased the viscosity of PTT, while ultra-fine talc increased the viscosity of PTT due to the hindrance of the layer structure of talc.     

Structure and properties of bio-based poly(trimethylene terephthalate)/polyamide 56 blends prepared by melt mixing

The extensive use of conventional petroleum-based polymers consumes large amounts of energy and emits a lot of carbon dioxide. Therefore, the development and popularization of bio-based polymer materials are highly significant for ecological reasons. Herein, a series of poly(trimethylene terephthalate)/polyamide 56 (PTT/PA56) blends with different weight ratios were prepared by melt blending of two bio-based polymers, PTT and PA56. The phase structure, miscibility, crystallization and melting behaviors, crystal structure, and mechanical and water absorption properties of PTT/PA56 blend systems were investigated. The results showed that PTT and PA56 were immiscible in the whole range of compositions. The immiscibility of the blend system intensified with the increase of dispersed phase content. As PA56 content increased, tensile strength and elongation at break of samples assumed an increasing trend, whereas impact strength initially remained almost unchanged and then gradually decreased. In contrast, increasing PA56 content gradually increased water absorption of samples. Comprehensive analysis indicated that the best combination of different properties was obtained for the PTT/PA56 blends including 60–80 wt% PA56.     

Thermal,mechanical, and morphological investigation of injection molded poly(trimethylene terephthalate)/carbon fiber composites

Injection molded poly(trimethylene terephthalate) (PTT)/carbon fiber (CF) composites have been fabricated using a twin screw micro compounder. The effect of CF reinforcement on the thermal, mechanical, dynamic mechanical, and microscopic properties of the composite was investigated. Addition of 30 wt% of CF into PTT resulted in the significant enhancement of tensile (120%) and flexural (30%) strength compared to neat PTT. The rule of mixture was successfully employed for theoretical calculations of tensile modulus and the calculated values were compared with the experimental results. Similarly, CF reinforced (30 wt%) PTT composites exhibited an increase of more than a 150°C in the heat deflection temperature. Scanning electron microscopy analysis of the tensile fracture specimens revealed uniform distribution of the CFs with good polymer matrix and fiber adhesion. Overall, the results obtained indicate the enhancement of properties with increasing fiber content, confirming better fiber and polymer matrix compatibility. POLYM. COMPOS., 33:1933–1940, 2012. © 2012 Society of Plastics Engineers     

Preparation and properties of PC/SAN alloy modified with styrene‐ethylene‐butylene‐styrene block copolymer

A polycarbonate (PC)/ poly (styrene‐co‐acrylonitrile) (SAN) alloy modified with styrene‐ethylene‐butylene‐styrene (SEBS) block copolymer was prepared and the influence of SEBS content, PC content, and types of modifier on Izod notched impact strength, tensile strength, flexural strength, and Vicat softening temperature was studied. The results showed that the addition of SEBS could obviously increase the Izod notched impact strength and the elongation at break and decrease the tensile and flexural strength and Vicat softening temperature. PC/SAN alloy modified with SEBS had better mechanical properties than the PC/SAN alloy modified with ABS. DSC analysis and SEM photographs revealed that the SEBS was not only distributed in the SAN phase but also distributed in PC phase in a PC/SAN/SEBS alloy while the ABS was mainly distributed in SAN phase in a PC/SAN/ABS alloy. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Structure–property evolution of poly(ethylene terephthalate)/poly(trimethylene terephthalate) side-by-side self-crimp filament

To investigate the microstructure and mechanical properties of self-crimping two-component side-by-side bicomponent filament, this paper focuses on systematically investigating the structure–property evolution of poly(ethylene terephthalate) (PET)/poly(trimethylene terephthalate) (PTT) side-by-side bicomponent filament prepared via melt spinning with various component ratios, drawing and heating treatment. The investigation was operated upon the combination of morphology analysis, thermal analysis, crystallization, and orientation analysis. The variation of cross section and curl-morphology, crystallization, and microstructures mainly containing lamellar and microfibrillar crystals as well as their effects on the mechanical and self-crimping properties were discussed. As the draft ratio (DR) increases, the crystallinity, sonic orientation factor, tensile strength, and crimp-recovery rate of the filaments were increased. The sonic orientation factor in the crystalline region decreases from 0.923 to 0.777 but increases from 0.677 to 0.903 in the amorphous region. In contrast to the variation of the DR, heating temperature has a limited effect on the tensile strength of the PET/PTT hybrid filaments. Crimp-recovery rate, however, first increases to 11.8 and then decreases to 9.8 with an increasing heating temperature from 144 to 168°C. Most of these behaviors have been attributed to changes in the ratio of contractile stress for both PTT and PET components, originating from microstructural evolution in hybrid filaments, including crystal growth, breakage, deflection, and deformation of chains along the axial direction. As a summary, an interpretive diagrammatic sketch has been proposed to clarify the structure–property relationships of the commercial PET/PTT filaments.     

Recycled poly(ethylene terephthalate)/linear low‐density polyethylene blends through physical processing

Poly(styrene‐ethylene/butylene‐styrene) (SEBS) was used as a compatibilizer to improve the thermal and mechanical properties of recycled poly(ethylene terephthalate)/linear low‐density polyethylene (R‐PET/LLDPE) blends. The blends compatibilized with 0–20 wt % SEBS were prepared by low‐temperature solid‐state extrusion. The effect of SEBS content was investigated using scanning electron microscope, differential scanning calorimeter, dynamic mechanical analysis (DMA), and mechanical property testing. Morphology observation showed that the addition of 10 wt % SEBS led to the deformation of dispersed phase from spherical to fibrous structure, and microfibrils were formed at the interface between two phases in the compatibilized blends. Both differential scanning calorimeter and DMA results revealed that the blend with 20 wt % SEBS showed better compatibility between PET and LLDPE than other blends studied. The addition of 20 wt % of SEBS obviously improved the crystallizibility of PET as well as the modulus of the blends. DMA analysis also showed that the interaction between SEBS and two other components enhanced at high temperature above 130°C. The impact strength of the blend with 20 wt % SEBS increased of 93.2% with respect to the blend without SEBS, accompanied by only a 28.7% tensile strength decrease. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Studies on the rheological,phase morphologic,thermal and mechanical properties of poly(trimethylene terephthalate)/ethylene propylene diene monomer copolymer grafted with maleic anhydride/metallocene polyethylene blends

The rheological, phase morphologic, thermal and mechanical properties of poly (trimethylene terephthalate)/metallocene polyethylene (PTT/mPE) blends in the presence of ethylene propylene diene monomer copolymer grafted with maleic anhydride (EPDM-g-MAH) as compatibilizer are studied by means of a capillary rheometer, scanning electron microscopy (SEM), differential scanning calorimetry (DSC) and thermogravimetric analyzer (TGA). Results suggest that the compatibility of PTT/mPE blends is improved greatly after the addition of a compatibilizer. The radius of the dispersed phase in the system decreases greatly when the compatibilizer is added into the blend. When the amount of compatibilizer exceeds 8 wt-%, the size of dispersed phase becomes larger again. This phenomena could be attributed to the higher viscosity of the EPDM-g-MAH phase, which is dispersed more difficulty in the PTT phase of lower viscosity, thus the mixing efficiency is apparently decreased during the melt blending process. Moreover, the melt viscosity of the blend reaches the maximal value in case of 4 wt-% compatibilizer content, above which it would decrease again. This result is associated with the generation of more and bigger dispersed phase inside the bulk phase, thus the grafting efficiency at the interface is decreased, which could result in lower viscosity. The DSC results suggest that the mPE component shows a nucleating effect, and could increase the overall degree and rate of PTT crystallization, while the addition of a compatibilizer might slightly diminish these effects. In addition, the blend with 4 wt-% compatibilizer shows the best thermal stability. Furthermore, the Izod impact strength and the tensile strength at room temperature of the blend are also markedly improved by the addition of a 4–8 wt-% compatibilizer.     

Miscibility,Mechanical and Thermal Properties of Melt-Mixed Poly(trimethylene terephthalate)/Polypropylene Blends

This study examined the miscibility, mechanical and thermal properties of melt-mixed blends of PTT(poly(trimethylene terephthalate)) with PP(isotatic polypropylene). DMA and SEM results indicated that the PTT/PP blends are immiscible. Revealed from TGA analyses, the blends with a higher PP content showed a higher degradation temperature. A complex melting behavior was observed for the blends. The isothermal crystallization kinetics of the blends was analyzed from 200°C to 210°C using the Avrami equation. The WAXD results showed that the crystal structure of PTT remained unchanged in the blends. Nevertheless, the PP rich blends possessed lower tensile strength and higher elongation at break.     

Poly(trimethylene terephthalate) nanocomposite fibers by in situ intercalation polymerization: thermo-mechanical properties and morphology (I)

A series of poly(trimethylene terephthalate) (PTT) nanocomposites, containing an organically modified montmorillonite (C₁₂PPh-MMT), were prepared by in situ intercalation polymerization of dimethyl terephthalate (DMT) and 1,3-propanediol (PDO). The PTT nanocomposites were melt-spun at different organoclay contents and different draw ratios (DRs) to produce monofilaments. The nanocomposites were characterized by X-ray diffraction, electron microscopy, universal tensile testing, differential scanning calorimetry and thermogravimetric analysis. Some of the clay particles appeared well dispersed within the PTT matrix, while others were found to agglomerate with a size greater than 10 nm. The addition of a small amount of C₁₂PPh-MMT was sufficient to improve the thermo-mechanical properties of the PTT hybrid fibers. Both the thermal stability and the tensile strength increased with increasing clay content at DR=1. As the DR was increased from 1 to 9, the ultimate tensile strength of the hybrid fibers decreased, while the initial modulus remained constant.     

聚对苯二甲酸丙二酯研究进展

综述了聚对苯二甲酸丙二酯(PTT)的合成方法及原料生产方法,介绍了PTT的结构与物理机械性能、结晶性能、热性能和流变性能,认为发展PTT应优先发展环氧乙烷法生产1,3-丙二醇。     

Effects of reactive compatibilizer on the core-shell structured modifiers toughening of poly(trimethylene terephthalate)

Poly(trimethylene terephthalate)/polybutadiene grafted polymetyl methacrylate (PB-g-PMMA, MB) blends were prepared by melt processing with varying weight ratios (0-5 wt%) of diglycidyl ether of bisphenol-A (DGEBA) epoxy resin as a reactive compatibilizer. DMA result showed PTT was partially miscible with MB particles in the presence of the compatibilizer. Fourier transform infrared (FTIR) and rheological measurements further identified the reactions between PTT and DGEBA epoxy resin. Scanning electron microscopy (SEM) displayed that the core-shell structured modifiers exhibit a smaller dispersed domain size with the addition of DGEBA epoxy resin. Mechanical tests showed the impact and tensile properties of PTT blends are improved by the introduction of DGEBA epoxy resin to the blends. SEM and TEM results showed shear yielding of PTT matrix and cavitation of rubber particles were the major toughening mechanisms.     

超支化乙二胺三嗪聚合物对PPC/PBS共混体系的增强改性研究

以超支化乙二胺三嗪聚合物（HBETP）为改性剂,采用熔融共混法制备了聚碳酸亚丙酯（PPC）/聚丁二酸丁二醇酯（PBS）/HBETP共混物;利用动态热机械分析仪、热失重分析仪、电子万能试验机、旋转流变仪、扫描电子显微镜等,对其热性能、力学性能、流变性能、断面形貌等进行了表征。结果表明,当HBETP含量为0.5 %（质量分数,下同） 时,PPC/PBS/HBETP共混物在韧性基本保持不变的情况下,拉伸强度提高幅度最大,由7.56 MPa提高到11.22 MPa,增幅为49.6 %;HBETP的加入可以提高PPC/PBS的相容性,且适当的含量会使PPC/PBS的拉伸强度提升。     

碳纤维增强PBT/ABS-g-MAH复合材料的力学性能和流变行为

利用扫描电子显微镜、电子万能试验机、冲击试验机、旋转流变仪和差示扫描量热仪分别研究了聚对苯二甲酸丁二醇酯（PBT）/马来酸酐接枝丙烯腈丁二烯苯乙烯共聚物（ABS-g-MAH）/短切碳纤维（SCF）复合材料的相形态、力学性能、流变和结晶行为。结果表明,复合材料断面上纤维的分布较为均匀,SCF与PBT之间有较好的界面结合性能;当SCF含量为5 %~10 ％时,复合材料的力学性能得到明显提高;随着SCF含量的增加,复合材料熔体的复数黏度呈现先降低后升高的趋势;在体系中添加适量的SCF可以起到成核剂的作用,由于结晶变得相对容易,从而使结晶温度升高,然而过量的SCF会在一定范围内阻碍PBT的结晶。     

The effect of recycling number on the mechanical,chemical, thermal,and rheological properties of PBT/PC/ABS ternary blends: With and without glass‐fiber

The recycling possibilities of poly(butylene terephthalate)/polycarbonate/acrylonitrile–butadiene–styrene (PBT/PC/ABS) ternary blend with and without glass‐fiber content were investigated using repeated injection molding process. In this study, PBT/PC/ABS ternary blends were reprocessed at five times and the results were presented after each recycling process. The recycling possibility of PBT/PC/ABS ternary blend was evaluated by measuring the mechanical, chemical, thermal, and rheological properties. Mechanical properties were determined by the tensile strength, yield strength, strain at break, elastic modulus, impact strength, flexural strength, and flexural modulus. Chemical and thermal properties were evaluated by Fourier transform infrared spectroscopy, differential scanning calorimetry, thermal gravimetric analysis, and scanning electron microscopy. Rheological properties of the ternary blends were studied by melt flow index measurement. From the results, it was found that mechanical properties of recycled composites were better than virgin PBT/PC/ABS ternary blends. POLYM. COMPOS., 35:2074–2084, 2014. © 2014 Society of Plastics Engineers     

Novel polymer blends from polyester and bio‐based cellulose ester

A strategy to reduce the dependence on petroleum‐based building blocks and the disposal concerns of solid wastes was proposed by developing a novel polymer blend from bio‐based cellulose acetate butyrate (CAB) and poly(trimethylene terephthalate) (PTT). The thermodynamic immiscibility and the thermal behaviors of the polymer melt blends were investigated. The interfacial properties were analyzed to provide the theoretical guidance to improve the compatibility of blends. A reactive compatibilizer, poly(trimethylene terephthalate)‐graft‐(maleic anhydride) (PTT‐g‐MA) was prepared from melt reaction and characterized with FTIR. The compatibilizer was melt blended into the CAB and PTT blends. The effects of different compatibilizers on the phase morphologies and mechanical properties of blends were characterized and the interfacial interactions were studied. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

PTT/MMT复合材料流变性能的研究

采用熔融共混法制备了聚对苯二甲酸丙二酯/蒙脱土（PTT/MMT）复合材料,并采用毛细管流变仪对复合材料的流变性能进行了研究。结果表明,PTT和PTT/MMT复合材料均为假塑性流体,1 %~3 %的MMT就可以显著改善复合材料的流动性。复合材料的非牛顿指数大于PTT,表观黏度小于PTT,流动性优于PTT,可以在较低的温度下成型加工;复合材料的黏流活化能高于PTT,更适合通过升高温度的方法来改善其流动性。     

Toughening modification of PBT/PC blends with PTW and POE

New toughened poly(butylene terephthalate) (PBT)/bisphenol A polycarbonate (PC) blends were obtained by melt blending with ethylene–butylacrylate–glycidyl methacrylate copolymer (PTW) and ethylene‐1‐octylene copolymer (POE) in a twin‐screw extruder. The mechanical properties of PBT/PC blends were investigated. The presence of PTW or POE could improve the mechanical properties except for the tensile strength and flexural properties of the PBT/PC blends. However, a combination use of PTW and POE had a strong synergistic effect, leading to remarkable increases in the impact strength, elongation at break, and Vicat temperature and some reduction of the tensile strength and flexural properties. The relationship between mechanical properties and morphology of the PBT/PC/PTW/POE blends was studied. The morphology was observed by scanning electron microscopy and the average diameter of dispersed phase was determined by image analysis, and the critical interparticle distance for PBT/PC was determined. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 54–62, 2006