Modeling the thermal shock induced cracking in ceramics

Prediction of surface cracking in ceramics due to quenching is performed numerically using either the coupled criterion or a cohesive zone model. Under such a thermal shock, a network of short cracks with minimal spacing between them initiate and propagate until some of them stop while the others continue propagating. The numerical implementation consists of a periodic array of cracks modeled by a representative volume element. It allows crack initiation, simultaneous propagation and period doubling to be predicted. The investigation of the crack period doubling allows a precise determination of the optimal crack spacing, which decreases with an increasing thermal shock amplitude. The predicted crack spacing results are in agreement with experimental measurements.     

Preparation and thermal shock resistance of cordierite-spodumene composite ceramics for solar heat transmission pipeline

Cordierite-spodumene composite ceramics with 5, 10, 15 wt% spodumene used for solar heat transmission pipeline were in-situ prepared via pressureless sintering from kaolin, talc, γ-Al₂O₃ and spodumene. Effects of spodumene on densification, mechanical properties, thermal shock resistance, phase composition and microstructure of the composite ceramics were investigated. The results showed that spodumene used as flux material decreased the sintering temperature greatly by 40–80 °C, and improved densification and mechanical properties of the composite ceramics. Especially, sample A3 with 10 wt% spodumene additive sintered at 1380 °C exhibited the best bending strength and thermal shock resistance. The bending strengths of A3 before and after 30 thermal shock cycles (wind cooling from 1100 °C to room temperature) were 102.88 MPa and 96.29 MPa, respectively. XRD analysis indicated that the main phases of the samples before 30 thermal shock cycles were α-cordierite, α-quartz and MgAl₂O₄, and plenty of β-spodumene appeared after thermal shock. SEM micrographs illustrated that the submicron β-spodumene grains generated at the grain boundaries after thermal shock improved the thermal shock resistance. It is believed that the cordierite-spodumene composite ceramics can be a promising candidate material for heat transmission pipeline in the solar thermal power generation.     

Preparation and thermal shock resistance of corundum-mullite composite ceramics from andalusite

Corundum-mullite composite ceramics have high hardness, small plastic deformation and other excellent performances at high temperature. Corundum-mullite composite ceramics were fabricated from andalusite and α-Al₂O₃ by in-situ synthesis technology. Effects of mullite/corundum ratio and sintering temperatures on the water absorption, apparent porosity, bulk density, bending strength, thermal shock resistance, phase composition and microstructure of the sample were investigated. Results indicated that the in-situ synthesized mullite from andalusite combined with corundum satisfactorily, which significantly improved the thermal shock resistance as no crack formed after 30 cycles of thermal shock (1100 °C-room temperature, air cooling). Formula A4 (andalusite: 37.31 wt%, α-Al₂O₃: 62.69 wt%, TiO₂ in addition: 1 wt%, mullite: corundum=6:4 in wt%) achieved the optimum properties when sintering at 1650 °C, which were listed as follows: water absorption of 0.15%, apparent porosity of 0.42%, and bulk density of 3.21 g⋅cm⁻³, bending strength of 117.32 MPa. The phase composition of the sintered samples before and after thermal shock tests were mullite and corundum constantly. The fracture modes of the crystals were transgranular and intergranular fractures, which could endow the samples with high thermal shock resistance.     

Effect of Sm2O3 on microstructure,thermal shock resistance and thermal conductivity of cordierite-mullite-corundum composite ceramics for solar heat transmission pipeline

Cordierite-mullite-corundum composite ceramics for solar heat transmission pipeline were fabricated via pressureless sintering at a low sintering temperature with added Sm₂O₃. The effects of Sm₂O₃ on sintering behaviors, mechanical property, phase transformation, microstructure, thermal shock resistance and thermal conductivity of the composite ceramics were investigated. TEM analysis results demonstrated that Sm³⁺ located in glass and grain boundaries to facilitate the densification via the liquid-phase sintering mechanism and improve bending strength by grain refinement, respectively. Proper addition (3 wt%) of Sm₂O₃ could promote the crystallization of cordierite, and improve thermal shock resistance of the composite ceramics with an increasing rate of 16.70% for bending strength after 30 thermal shock cycles (air cooling from 1100 °C to RT). The composite ceramics possessed a superior thermal shock resistance, where a large amount of particles were formed to suppress crack initiation and propagation during thermal shock. Cordierite-mullite-corundum composite ceramics with proper Sm₂O₃ addition (3 wt%) had a lower thermal conductivity than that of composite ceramics without Sm₂O₃ addition by strengthening the scattering of phonon, which could reduce the heat loss during solar heat transmission process.     

A multi-scale model for predicting the thermal shock resistance of porous ceramics with temperature-dependent material properties

This paper develops a novel multi-scale thermal/mechanical analysis model which not only can efficiently measure the thermal shock response but also highly reflects the effects of diversiform micro-structures of porous ceramics. Knowledge of the temperature distribution and time-varied thermal stress intensity factors (SIF) is derived by finite element/finite difference method and the weight function method in the macro continuum model. The finite element analysis employs a micro-mechanical model in conjunction with the macro model for the purpose of relating the SIF to the thermal stress in the struts of the porous ceramics. The micro model around the crack tip was established by using Voronoi lattices to accurately explore the micro-architectural features of porous ceramics. Hot shock induced center crack and cold shock induced edge crack are both considered. Effects of relative density and pore size on the thermal shock resistance are investigated and the results are well coincident with the experimental tests. The influence of cell regularity and cross section shape of the cell struts is discussed and the corresponding explanations are provided. The importance of incorporating temperature-dependent material properties on the thermal shock resistance prediction is quantitatively represented. These multi-faceted models and results provide a significant guide to the design and selection of porous ceramics against the thermal shock fracture failure for the future thermal protection system of space shuttle.     

Preparation and thermal shock resistance of solar thermal absorbing corundum ceramics for concentrated solar power

The absorptivity of solar thermal absorber materials affects the heliothermal conversion efficiency of concentrated solar power systems. The solar absorbing ceramics were prepared by the fixed mixture of bauxit, Fe₂O₃, and TiO₂ with adding CuO in different percentages. The absorptivity and thermal shock resistance with the effect of adding CuO in different percentages were studied. Fe₂O₃ and TiO₂ have excellent optical properties, and CuO decreases the material's band gap to boost the electronic transition and increase the material absorptivity. The results showed that the material is sintered at 1380°C with an excellent absorptivity of 94.00% in the spectrum range of 0.3–2.5 μm, and the bending strength is 132.94 MPa. The bending strength was increased by 21.07% after 30 thermal shock cycles (1000°C-room temperature, air cooling). The liquid phase facilitates the synthesis of hercynite with excellent high temperature properties. The hercynite improves the thermal shock resistance of the material.     

Sintering behavior and thermal shock resistance of aluminum titanate (Al2TiO5)-toughened MgO-based ceramics

In order to improve the thermal shock resistance of MgO-based ceramics, aluminum titanate (Al₂TiO₅)-toughened MgO-based ceramics were successfully prepared by solid state sintering at 1450 °C and 1550 °C for 3 h starting from MgO and as-synthesized Al₂TiO₅ powders. The effects of various contents of Al₂TiO₅ second phase on the sintering behavior and thermal shock resistance of MgO-based ceramics were investigated. The sintering behavior of sintered samples was evaluated by comparing the relative density, apparent porosity, bending strength, phase composition as well as microstructure. The thermal shock resistance of sintered samples was characterized by using the residual bending strength after three thermal cycles and thermal expansion coefficient. The obtained samples with 10 wt% Al₂TiO₅, which were sintered at 1550 °C for 3 h, showed the highest relative density, lowest apparent porosity as well as optimum bending strength. In addition, the samples added 15 wt% Al₂TiO₅ at 1550 °C with a dwell time of 3 h were the highest residual bending strength and lowest thermal expansion coefficient. It revealed that the enhancement in thermal shock resistance was ascribed to the reduction of thermal expansion coefficient.     

提高刚玉质耐火材料热震稳定性的研究

利用微气孔和弥散的ＺｒＯ２能改善耐火材料热震稳定性的特点，在含有一定数量微气孔的刚玉质耐火材料中，加入弥散的ＺｒＯ２，将ＺｒＯ２的增韧作用应用于刚玉质耐火材料热震稳定性的设计中。实验结果表明，当气孔的数量控制在１４％左右，ＺｒＯ２的外加量达６～９ｗｔ％时，能有效地改善刚玉质耐火材料的热震稳定性。在１１００℃，水冷的条件下，经１０次热震试验后，耐压强度保持不变，残余抗折强度为４５％。     

碳氢燃料热裂解与引发裂解换热对比实验

通过流动管反应器对碳氢燃料RP-3在超临界条件下的热裂解及引发裂解进行了实验,对两种条件下的燃料吸热能力及传热特性进行了对比分析,并对裂解产物进行了采样分析。结果表明,引发裂解降低了燃料的裂解起始温度,在一定温度区间内提高了燃料的裂解率,从而有效提高了燃料热沉,在相同热通量条件下,降低了燃料温度,并降低了加热段壁面温度。对流换热受化学反应及物性变化的影响,燃料裂解吸热可增强换热,而大量气态产物的生成会降低换热,因此,裂解反应的增强不一定增强换热。     

改善耐火制品热震稳定性的方法

提出了改进耐火制品热震稳定性的方法：1制品的气孔率适当;2控制原料的颗粒配比;3增加微细裂纹并形成网络结构;4形成界面结合;5添加膨胀性材料。     

Preparation and thermal shock resistance of anorthite solar thermal energy storage ceramics from magnesium slag

Anorthite solar thermal energy storage ceramics were fabricated from magnesium slag solid waste by pressureless sintering. The effects of CaO/SiO₂ ratio and sintering temperature on the physical, chemical, and thermophysical properties of ceramics were explored. X-ray diffraction results demonstrated that thermal shock process contributed to the formation of anorthite, and increasing CaO/SiO₂ ratio promoted the transformation of anorthite (CAS₂) into melilite (C₂AS). Some micro-cracks were found according to SEM analysis, forming by the mismatch of thermal expansion coefficients among phases. The combined effects of the low thermal expansion coefficient of anorthite and micro-crack toughing endowed the ceramic with good thermal shock resistance. Optimum comprehensive performances were observed in the sample with a CaO/SiO₂ ratio of 0.58 sintered at 1160°C, of which the specific thermal storage capacity was 0.63 J·g^-1·°C^-1(room temperature). The bending strength increased by 0.22% after 30 thermal shock times (room temperature-800°C, wind cooling). Therefore, the anorthite ceramics exhibited great potential for solar thermal energy storage.     

Effect of grain size and orientation degree on thermal shock resistance of BN-matrix textured ceramics under cyclic thermal shock

Hexagonal boron nitride (h-BN) has a typical two-dimensional flake structure, so the anisotropy of h-BN grains caused by directional arrangement cannot be ignored when studying the thermal vibration resistance of materials under thermal cycling. In this paper, h-BN-matrix textured ceramics prepared with different holding time were selected, and the effects of thermal vibration temperature difference and thermal cycles on the phase and thermal vibration resistance of h-BN-matrix textured ceramics were studied. The results show that under the condition of high-frequency thermal cycling, the residual strength ratio (RSR) of BN-based textured ceramics is closely related to the holding time and showing obvious anisotropy. At the same time, there is a thermal vibration temperature range in which the internal stress will change from relief to re-accumulation.     

压痕法研究ZrO2层状复合陶瓷的抗热震性

用压痕法测试了单层和层状两种ZrO2陶瓷材料的抗热震性能.研究结果表明ZrO2层状复合陶瓷的临界热震温差△Tc=400℃,比ZrO2单层陶瓷高出150℃左右,同时还表现出其△Tc与陶瓷厚度无关的优异性质.现场试验结果也证明,ZrO2层状复合陶瓷抵抗1500℃冷热骤变的能力优于ZrO2单层陶瓷.研究认为,界面压应力作用部分或全部抵消了热冲击应力,使裂纹在界面处发生偏转,提高了材料的断裂能和断裂功,导致材料的抗热震性提高.     

Numerical modelling of the quasi-brittle behaviour of refractory ceramics by considering microcracks effect

In the steelmaking industry, the inner lining of ladles is made of refractory ceramics, which are constantly subjected to thermal shocks during their service. Experimentally, it is observed that pre-existing microcracks could significantly increase the thermal shock resistance of these ceramics. The presence of such microcracks network within the refractory microstructure could lead to a non-linear quasi-brittle mechanical behaviour.To model this quasi-brittle behaviour, a suitable numerical approach is the Discrete Element Method (DEM), which can circumvent the limitations of more conventional continuum approaches in capturing microstructural effects required to simulate multi-fracture propagation.Here, it is aimed to simulate such quasi-brittle behaviour by initial well-distributed damages, with a strength dispersion following a Weibull distribution. In this way, the microcracks effect on the quasi-brittle behaviour of a numerical sample under uniaxial and cyclic tensile tests is investigated. Ultimately, a quantitative DEM model to simulate such a complex behaviour is proposed.     

Fabrication and thermal shock behavior of periclase-forsterite aggregates with micro-nanometer dual-pore-size structures

To improve the service life of periclase-forsterite refractories, it is important to develop aggregates with high thermal shock resistance. In this study, periclase-forsterite aggregates with good resistance to thermal shock and micro-nanopores were prepared using high-silicon magnesite, silica, and silica sol. Microcracks were generated in the multiphase aggregates, which inhibited the continuous propagation of cracks during thermal shock through mismatched thermal expansion coefficients. Based on Hasselman's thermal shock stability factor, the reduction in the average thermal expansion coefficient and improved mechanical characteristics were critical factors in improving the thermal shock resistance of the multiphase aggregates. As a binder, silica sol provided nano-SiO₂ and superplasticity, which facilitated the formation of micro-nanopores and strengthened the combination of the various phases in the aggregates.     

High thermal-conductivity rGO/ZrB2-SiC ceramics consolidated from ZrB2-SiC particles decorated GO hybrid foam with enhanced thermal shock resistance

Graphene derivative materials exhibit excellent mechanical and thermal properties, which have been extensively used to toughen ceramics and improve thermal shock resistance. To overcome the thermal agglomeration of graphene oxide (GO) during heating and drying process, ZrB₂-SiC particles decorated GO hybrid foam with uniformly anchored ceramic particles was synthesized by electrostatic self-assembly and liquid nitrogen-assisted freeze-drying process. Densified rGO/ZrB₂-SiC ceramics with varying microstructure, thermal physical and mechanical properties were obtained by adjusting the content of decorated ceramic particles. Although the flexural strength of rGO/ZrB₂-SiC ceramics have an attenuation compared with that of ZrB₂-SiC ceramic, the thermal conductivity, work of fracture and thermal shock resistance are greatly improved. rGO/ZrB₂-SiC ceramics exhibit delayed fracture and increasing R-curve behavior during the crack propagation. The novel preparation technology allows for the well dispersion of rGO in ZrB₂-SiC ceramics and can be easily extended to other ceramic or metal materials systems.     

Cyclic thermal shock behaviors of carbon fibers reinforced SiCN ceramics with bio-inspired Bouligand-like architectures

Ceramic matrix composites (CMCs) are commonly used for high temperature components in aircrafts. However, thermal shock, as a typical loading case, will cause high thermal stresses in CMCs resulting in brittle fracture failure, and material cracking caused by thermal shock can further reduce the effectiveness of thermal protection function. In the present paper, we propose a bionic hierarchical fiber preform design method to improve the thermal shock resistance of ceramics. The effect of architectures of fiber preforms of continuous carbon fiber-reinforced CMCs on the thermal shock resistance was investigated to understand its importance and the related mechanical mechanisms. Thermal shock (cycling) tests were performed with continuous carbon fibers reinforced SiCN ceramic matrix composites (C_f/SiCN) prepared by PIP. 3D micro-CT scan and three-point bending tests were also conducted to evaluated the resultant damage. The results showed that smaller internal damage and higher thermal shock resistance can be obtained in comparison to pure SiCN ceramics, and the underlying mechanism can be explained by the fact that smaller pitch angle can resist the through-thickness crack propagation via promoting diffused in-plane damage. The present study offers a possibility in developing biomimetic C_f/SiCN ceramics with excellent thermal shock behavior.     

Investigating the effect of andalusite on mechanical strength and thermal shock resistance of cordierite-spodumene composite ceramics

For increasing working stability of cordierite-spodumene composite ceramics for solar heat transmission pipeline, andalusite was utilized as modified additive to improve mechanical strength and thermal shock resistance of the composite ceramics. The effects of andalusite on densification, mechanical strength, thermal stability, phase composition and microstructure were studied. The experiment results showed that andalusite significantly influenced bending strength and thermal shock resistance of the composite ceramics. Especially, specimen B1 with 5 wt% andalusite sintered at 1400 °C achieved the best performances. The linear shrinkage, water absorption, apparent porosity, bulk density and bending strength were 5.62%, 0.02%, 0.06%, 2.19 g cm^?3 and 104.94 MPa, respectively. After 30 thermal shock cycles (wind cooling from 1100 °C to room temperature), the residual strength of the specimen increased to 110.65 MPa, accompanying with ?5.44% strength loss rate. The XRD and SEM analysis illustrated that mullite grains with short rod-like shape could prevent crack growth of inter-granular fracture to enhance bending strength of the specimens. Furthermore, the generation of β-spodumene grains with low thermal expansion coefficient after thermal shock improved thermal shock resistance of the composite ceramics. It is considered that the cordierite-spodumene composite ceramics with high densification, good mechanical strength and excellent thermal stability can be a potential material for high temperature thermal transmission pipeline in solar thermal power generation.     

Comparative evaluation of two different methods for thermal shock resistance of laminated ZrB2-SiCw/BN ceramics

The thermal shock resistance (TSR) of laminated ZrB₂–SiC_w/BN ceramic was evaluated through indentation-quench and quenching-strengthening methods. It was correspondingly compared to monolithic ZrB₂–SiC_w ceramic. In the indentation-quench method with consideration to crack propagation on the surface layer, the critical thermal shock temperature of laminated ZrB₂–SiC_w/BN ceramic with surface residual tensile stress was 550?°C, which was lower than monolithic ZrB₂–SiC_w ceramic (600?°C). Unlike the microscopic method of crack growth measurement through indentation-quench testing, the quenching-strengthening method, which was based on the macroscopic properties of the material, mainly characterizing the residual strength subsequently to thermal shock, the critical thermal shock temperatures of the laminates and monolithic were 609?°C and 452?°C, respectively. Compared to the brittle fracture of ZrB₂–SiC_w ceramics, the deflection, bifurcation and delamination of the cracks as the main TSR mechanisms of the laminated ceramics, were revealed through quenching-strengthening method, which was more suitable for the TSR characterization of laminated ceramics.     

In situ synthesis and thermal shock resistance of mullite used for thermal storage ceramics in solar thermal power generation

Abstract

Mullite ceramic, as one of high performance thermal storage ceramics for solar thermal power generation systems, was in situ fabricated via semidry pressing and pressureless sintering in the air. Andalusite (57–68 wt-%) and calcined bauxite (24–29 wt-%) were used as the raw materials, with kaolin and a tiny of boric acid being added to promote the densification and improve the mechanical properties. The best physical properties and thermal shock resistance were obtained on an optimum A3 sample sintered at 1600°C for 3 h, i.e. a bending strength of 120·44 MPa and 30 cycles thermal shock cycling without cracking (wind cooling from 1000°C to room temperature) with a loss of bending strength of 8·7%.