共查询到20条相似文献,搜索用时 62 毫秒
1.
2.
3.
4.
5.
《微电机》2016,(7)
在伺服系统中,为了尽可能提高测角精度,本文提出了"双通道多对极旋转变压器+轴角数字转换器AD2S1210+FPGA"测角编码控制方案。通过FPGA来控制AD2S1210的解码和同步问题,并采用串行通信实现绝对角位置的输出,该系统可适用于0~360°范围内的转角位置测量。并且针对系统的误差,对旋转变压器的双通道数据的组合纠错进行了深入的研究。整个测角系统电路在PADS2007的设计环境下设计实现,并基于Xilinx公司的FPGA芯片XC6SLX45,通过VHDL语言的软件编程方式对组合纠错功能进行了验证。仿真结果表明该测角系统可满足高速度、高精度的设计要求。 相似文献
6.
随着无刷直流电动机转速的增高和可靠性要求的提升,旋转变压器在转子位置检测中的应用价值愈发得到重视。依据旋转变压器的位置检测原理,基于AD2S1210设计了旋转变压器的驱动和信号调理电路,在分析该芯片与数字信号处理器接口及通讯模式的基础上,利用AD2S1210和数字信号处理器设计并实现了高速高可靠无刷电动机控制系统,并对传感器接口方式、角度分辨率、系统采样频率等影响无刷电动机换相精度的关键因素进行定量分析,最后通过搭建硬件平台进行实验测试,验证了旋转变压器用于高速无刷电动机精确换相控制的有效性和可靠性。 相似文献
7.
8.
9.
10.
设计了一种基于旋转变压器的永磁推进电机位置和速度检测电路。分析了解码芯片的解码原理、数据转换(角度和转速)关系、解码电路以及解码程序流程,并在电机静止不同位置和不同电机转速下,通过Quartus II 9.1仿真软件对AD2S1210旋变解码板获取的角度和转速数据进行了测试,给出了电机运行下的旋转变压器输入输出相关波形。结果表明设计的基于AD2S1210解码电路用于永磁电机转子位置和速度检测方法可行,解码角度和速度数据精度高,波动范围小,抗干扰强,能够满足永磁推进系统的高性能、高可靠性的要求。 相似文献
11.
12.
特高压线路工频参数测试干扰分析是选择适合工频参数测试方法及测试结果分析的重要基础。测试了1 000 kV皖南-浙北特高压线路正序和零序参数测试期间的干扰电压信号,分析了其频谱特征;在此基础上,通过与正序参数仿真计算值的对比分析了正序参数实际测试偏差。结果表明:皖南-浙北特高压同塔双回线路工频参数测试期间,干扰电压存在“三相不平衡性及时变性”的特点;工频法和异频法2种不同方法得到的线路参数测试结果存在一定差异;干扰电压“时变”时,线路工频参数测试宜采用异频法。 相似文献
13.
《国外电子测量技术》2014,(10)
正Qingdao,China7.16-19,2015The International Conference on Electronic MeasurementInstruments(ICEMI)is the world’s premier conference dedicated to the electronic measurement and test of devices,boards and systems that is covering the complete cycle from design,verification,test,diagnosis,failure analysis and process of manufactory and products 相似文献
14.
《国外电子测量技术》2014,(9)
正Qingdao,China7.16-19,2015The International Conference on Electronic MeasurementInstruments(ICEMI)is the world's premier conference dedicated to the electronic measurement and test of devices,boards and systems that is covering the complete cycle from design,verification,test,diagnosis,failure analysis and process of manufactory and products 相似文献
15.
16.
17.
S. Y. Wu B. N. Tran F. Y. Davis C. L. Trent D. L. Edberg W. A. Geideman 《Integrated ferroelectrics》2013,141(3):281-291
Abstract Smart materials of lead-zirconate-titanate (PZT) piezoelectric ceramics have attracted attention in recent years for active vibration control, acoustic noise suppression, health monitoring and damage assessment. We at McDonnell Douglas Aerospace have been studying these ceramics for use as sensors and actuators in various space and aircraft structures. In this paper, we will report results of a recent study on active vibration control using monomorph PZT actuators. The experiments were performed on thin aluminum cantilever beams. Collocated and non-collocated sensors and actuators were employed. Two control techniques: the classical velocity feedback and adaptive feedback controls, were investigated. We have obtained significant damping and broadband vibration attenuation of greater than 30 dB using the classical control with the single-input single-output feedback approach. A 24 dB reduction has also been achieved using the adaptive control with the multiple-input single-output approach. Detailed experimental methods and results will be described. 相似文献
18.
电站锅炉停用保护剂多采用十八胺和表面活性胺。对这2种停用保护剂进行了应用效果对比研究,即对湿冷机组、空冷机组采用十八胺或表面活性胺、有无凝结水精处理系统等6台机组停机和启动过程中给水、主蒸汽和凝结水的氢电导率变化情况进行分析。研究结果表明:在停机过程和启动过程,2种保护剂均会在水汽系统中发生部分分解,导致水汽系统的氢电导率显著升高;表面活性胺和十八胺比较,使用前者,机组启停机过程可保持凝结水精处理系统正常投运,因而可使水汽质量迅速达标,对机组安全运行有利,因此推荐采用表面活性胺作为锅炉停用保护剂。 相似文献
19.