Friction and wear behavior of Ni-P coated Si3N4 reinforced Al6061 composites

Al6061 matrix composite reinforced with nickel coated silicon nitride particles were manufactured by liquid metallurgy route. Microstructure and tribological properties of both matrix alloy and developed composites have been evaluated. Dry sliding friction and wear tests were carried out using pin on disk type machine over a load range of 20-100 N and sliding velocities of range 0.31-1.57 m/s. Results revealed that, nickel coated silicon nitride particles are uniformly distributed through out the matrix alloy. Al6061-Ni-P-Si₃N₄ composite exhibited lower coefficient of friction and wear rate compared to matrix alloy. The coefficient of friction of both matrix alloy and developed composite decreased with increase in load up to 80 N. Beyond this, with further increase in the load, the coefficient of friction increased slightly. However, with increase in sliding velocity coefficient of friction of both matrix alloy and developed composite increases continuously. Wear rates of both matrix alloy and developed composites increased with increase in both load and sliding velocity. Worn surfaces and wear debris was examined using scanning electron microscopy (SEM) for possible wear mechanisms. Energy dispersive spectroscope (EDS), X-ray diffraction (XRD) and X-ray photoelectron spectroscope (XPS) techniques were used to identify the oxides formed on the worn surfaces and wear debris.     

Effect of transfer film structure, composition and bonding on the tribological behavior of polyphenylene sulfide filled with nano particles of TiO2, ZnO, CuO and SiC

The tribological behavior of polyphenylene sulfide (PPS) filled with inorganic nano particles was studied. The fillers investigated were TiO₂, ZnO, CuO and SiC whose sizes varied from 30 to 50 nm. The polymer composites were compression molded with varying proportions of these fillers. Wear and friction tests were performed in a pin-on-disk configuration at a sliding speed of 1.0 m/s, nominal pressure of 0.65 MPa, and counterface roughness of 0.10 μm Ra. The polymer composite pins slid against hardened tool steel counterfaces. The transfer films of the composite materials formed on the counterfaces during sliding were studied by optical microscopy and X-ray photoelectron spectroscopy (XPS) and the adhesion between the transfer film and counterface was measured in terms of the peel strength. It was found that the wear rate of PPS decreased when TiO₂ and CuO were used as the fillers but increased with ZnO and SiC fillers. The optimum wear resistance was obtained with 2 vol.% CuO or TiO₂. These filled composites had the coefficients of friction lower than that of the unfilled PPS. The wear behavior of the composites is explained in terms of the topography of transfer film and adhesion of transfer film to the counterface as observed from peel strength studies. There is a good correlation observed between the transfer film-counterface bond strength and wear resistance.     

Tribological properties of spark-plasma-sintered ZrO2(Y2O3)-CaF2-Ag composites at elevated temperatures

Spark-plasma sintering is employed to synthesize self-lubricating ZrO₂(Y₂O₃) matrix composites with different additives of CaF₂ and Ag as solid lubricants by tailoring the composition and by adjusting the sintering temperature. The friction and wear behavior of ZrO₂(Y₂O₃) matrix composites have been investigated in dry sliding against an alumina ball from room temperature to 800 °C. The effective self-lubrication at different temperatures depends mainly on the content of various solid lubricants in the composites. The addition of 35 wt.% Ag and 30 wt.% CaF₂ in the ZrO₂(Y₂O₃) matrix can promote the formation of a well-covered lubricating film, and effectively reduce the friction and wear over the entire temperature range studied. The friction coefficients at low temperatures were at a minimum value for the composite containing 35 wt.% of silver. At this silver concentration, low and intermediate temperature lubricating properties are greatly improved without affecting high-temperature lubrication by the calcium fluoride in ZrO₂(Y₂O₃) matrix composites. The worn surfaces and transfer films formed during wear process have been characterized to identify the synergistic lubrication behavior of CaF₂ and Ag lubricants at different temperatures.     

Friction and wear behaviour of WC-Co-Cr3C2-VC cemented carbides obtained from nanocrystalline mixtures

The effect of adding Cr₃C_2, VC or a mixture of both as a grain growth inhibitors to cemented carbides obtained from WC-12 wt.%Co nanocrystalline mixtures on the behaviour of friction and dry sliding wear have been studied. All the wear tests were performed on a tribometer with ball on disc configuration, using a WC-6 wt.%Co ball as a counterpart with normal contact loads of 40 and 60 N, sliding distance of 2000 m and a sliding speed of 0.1 m/s. A significant reduction in the wear rates was observed by the effect of the aforementioned additives, in particular for the VC, which showed an increase in the wear resistance of the order of 90%. The analysis of wear and surface damage were correlated to the observed behaviour.     

Carbon fabric reinforced polyetherimide composites: Optimization of fabric content for best combination of strength and adhesive wear performance

Polyacrylonitrile (PAN) based high strength carbon fabric (plain weave) reinforced polyetherimide (PEI) composites were fabricated using impregnation technique by selecting five different contents of carbon fabric, viz. 85, 75, 65, 55 and 40 vol.%. These bidirectional (BD) composites were evaluated for their mechanical strength as well as tribological behavior in adhesive wear mode. Dry adhesive wear studies were conducted on a custom designed wear tester in which high PV conditions can be simulated. Tests were conducted at various operating parameters such as load, temperature and orientation of fabric with respect to the sliding plane. Two important results were observed; firstly the moderate CF contents (75, 65 and 55 vol.%) proved to be the most effective in manifold increase in mechanical strength of PEI and secondly, the composites with fabric in the direction normal to sliding plane led to very high coefficient of friction (μ). When fabric was parallel to the sliding plane, significant improvement in the tribo-properties of PEI in terms of very high tribo-utility (up to 600 N), appreciably low μ and enhanced wear resistance (W_R) (in the range of 10⁻¹⁶ m³/N m) was achieved. The extent of improvement, however, strongly depended on the operating parameters and fabric content. A fairly good correlation was obtained between W_R and combination of mechanical properties such as ultimate tensile strength (S), and interlaminar shear strength (ILSS). Wear mechanism studies by SEM supported the observed wear performance of composites.     

Effect of TiB2 particles on sliding wear behaviour of Al–4Cu alloy

Dry sliding wear of Al–4Cu–xTiB₂ (x = 0, 2.5, 5, 7.5 and 10 wt.%) in situ composites have been studied in the peak-aged condition using a pin-on-disc wear testing machine at different loads. The composites were prepared by the reaction of a mixture of K₂TiF₆ and KBF₄ salts with molten alloy. The results indicate that TiB₂ particles markedly improve the wear performance of the Al–4Cu alloy. The wear resistance increases with increase in the amount of TiB₂. The load bearing capacity of the alloy during wear increases in presence of TiB₂ particles. Study of the wear surfaces and debris of both alloy and composites using the scanning electron microscope suggests that the improvement in wear resistance is mainly due to the formation of finer debris.     

Study of tribological performance of ECR-CVD diamond-like carbon coatings on steel substrates: Part 1. The effect of processing parameters and operating conditions

Diamond-like carbon (DLC) coatings were prepared on AISI 440C steel substrates at room temperature by electron cyclotron resonance chemical vapor deposition (ECR-CVD) process in C₂H₂/Ar plasma. Using the designed Ti/TiN/TiCN/TiC interfacial transition layers, relatively thick DLC coatings (1-2 μm) were successfully prepared on the steel substrates. The friction and wear performance of the DLC coatings was evaluated by ball-on-disk tribometry using a steel counterbody at various normal loads (1-10 N) and sliding speeds (2-15 cm/s). By optimizing the deposition parameters such as negative bias voltage, DLC coatings with hardness up to 30 GPa and friction coefficients lower than 0.15 against the 100Cr6 steel ball could be obtained. The friction coefficient was maintained for 100,000 cycles (∼2.2 km) of dry sliding in ambient environments. In addition, the specific wear rates of the coatings were found to be extremely low (∼10⁻⁸ mm³/Nm); at the same time, the ball wear rates were one order of magnitude lower. The influences of the processing parameters and the sliding conditions were determined, and the frictional behavior of the coatings was discussed. It has been found that higher normal loads or sliding speeds reduced the wear rates of the coatings. Therefore, it is feasible to prepare hard and highly adherent DLC coatings with low friction coefficient and low wear rate on engineering steel substrates by the ECR-CVD process. The excellent tribological performance of DLC coatings enables their industrial applications as wear-resistant solid lubricants on sliding parts.     

Hot wear properties of ceramic and basalt fiber reinforced hybrid friction materials

In the present study, hybrid friction materials were manufactured using ceramic and basalt fibers. Ceramic fiber content was kept constant at 10 vol% and basalt fiber content was changed between 0 to 40 vol%. Mechanical properties and friction and wear characteristics of friction materials were determined using a pin-on-disc type apparatus against a cast iron counterface in the sliding speeds of 3.2–12.8 m/s, disc temperature of 100–350 °C and applied loads of 312.5–625 N. The worn surfaces of the specimens were examined by SEM. Experiments show that fiber content has a significant influence on the mechanical and tribological properties of the composites. The friction coefficient of the hybrid friction materials was increased with increasing additional basalt fiber content. But the specific wear rates of the composites decreased up to 30 vol% fiber content and then increased again above this value. The wear tests showed that the coefficient of friction decreases with increasing load and speed but increases with increasing disc temperature up to 300 °C. The most important factor effecting wear rate was the disc temperature followed by sliding speed. The materials showing higher specific wear rates gave relatively coarser wear particles. XRD studies showed that Fe and Fe₂O₃ were present in wear debris at severe wear conditions which is indicating the disc wear.     

Characterization and mechanical/tribological properties of nano Au-TiO2 composite thin films prepared by a sol-gel process

Nano Au-TiO₂ composite thin films on Si(1 0 0) and glass substrates were successfully prepared with a facile sol-gel process followed by sintering. The morphology and mircostructure of the films were investigated via X-ray diffractometry (XRD), X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), and scanning electron microscopy (SEM). The Au particles, of diameter 14-22 nm depending on the sintering temperatures used, were found to be well dispersed in the TiO₂ matrix, with a small amount of the particles escaped from the film. The surfaces of the films were uniform, compact and crack-free. Hardness and elastic modulus of the films were measured by using the nanoindentation technique. Friction and wear properties were investigated by using a one-way reciprocating tribometer. It was found that the highest hardness and elastic modulus values were obtained for the films prepared with 500 °C sintering temperature. The films displayed superior antiwear and friction reduction performances in sliding against an AISI 52100 steel ball. With 5.0 mol% Au, the friction coefficient was only 0.09-0.10 and the wear life was more than 2000 sliding cycles. The friction coefficient and wear life decreased with increasing sliding speed and load. The failure mechanism of the Au-TiO₂ films was identified to be light scuffing and abrasion. Those films can be potentially applied as ultra-thin lubricating coatings.     

Abrasive wear of WC-FeAl composites

The abrasive wear behavior of tungsten-carbide iron-aluminide composite materials was investigated using a pin-on-drum wear-testing machine. Samples were prepared by uniaxially hot pressing blended powders. The wear rates of specimens containing 40 vol.% matrix of atomic composition, Fe₆₀Al₄₀, were measured and results compared with those of conventional WC-10 vol.% Co hardmetal. They were found to be comparable to those of WC-10% Co hardmetal, when abraded by 120 μm SiC papers under identical conditions. The wear resistance of WC-Fe₆₀Al₄₀ composites increased with reduction in WC-grain size and associated with increase in composite hardness. Scanning electron microscopy revealed that the wear surfaces of WC-40% Fe₆₀Al₄₀ composites and WC-Co hardmetal were similar in appearance. The higher hardness and work hardening ability of Fe₆₀Al₄₀ binder, as compared to Co metal, are believed to be responsible for the excellent abrasive wear resistance of WC composites containing iron aluminide binder.     

Influence of aging treatment on microstructure, wear and corrosion behavior of a nickel base hardfaced coating

In this work nickel based hardfacing alloy (Colmonoy 5) was deposited on 316 L (N) stainless steel substrate to study the effects of aging treatment on coating microstructure, wear and corrosion properties. Coatings, deposited through plasma transferred arc (PTA) welding process, were aged at 923 K for 5000 h. Microstructural characterization studies carried out by scanning electron microscopy (SEM) and transmission electron microscopy (TEM) revealed the coarsening of dendrites and precipitation of Cr₂₃C₆ particles in the aged coating. The wear behavior of the as deposited and aged coatings was compared in room temperature (RT) and high temperature (823 K) under dry sliding wear condition (pin-on-disc configuration). At RT, aged coating experienced more wear loss when compared to as-deposited. At high temperature, the wear loss was almost same with similar operating wear mechanisms (tribo-oxidation) for both as-deposited and aged coating. From pitting corrosion studies, it was found that aged coatings are more prone to pitting when compared to the as-deposited coatings.     

Friction, wear and N2-lubrication of carbon nitride coatings: a review

Recent results of tribological properties of carbon nitride (CN_x) coatings are reviewed. CN_x coatings of 100 nm thickness were formed on Si-wafer and Si₃N₄ disks by the ion beam mixing method. Friction and wear tests were carried out against Si₃N₄ balls in the environments of vacuum, Ar, N₂, CO₂, O₂ or air by a ball-on-disk tribo-tester in the load range of 80-750 mN and in the velocity range of 4-400 mm/s.It was found that friction coefficient μ is high (μ=0.2-0.4) in air and O₂, and low (μ=0.01-0.1) in N₂, CO₂ and vacuum. The lowest friction coefficient (μ<0.01) was obtained in N₂. It was also found that N₂ gas blown to the sliding surfaces in air effectively reduced the friction coefficient down to μ≈0.017. Wear rate of CN_x coatings varied in the range 10⁻⁹-10⁻⁵ mm³/N m depending on the environment.The wear mechanisms of CN_x in the nanometer scale were studied by abrasive sliding of an AFM diamond pin in air. It was confirmed that the major wear mechanism of CN_x in abrasive friction was low-cycle fatigue which generated thin flaky wear particles of nanometre size.     

Effect of fiber orientation on friction and wear of fiber reinforced polymeric composites

The friction and wear behavior of composites (i.e. uniaxially oriented graphite fiber-epoxy, Kevlar fiber-epoxy and biaxially oriented glass fiber-MoS₂-polytetrafluoroethylene (PTFE)) was investigated as a function of varying fiber orientations with respect to the sliding direction. In graphite fiber-epoxy composites, both wear and friction coefficients were minimum when the orientation of the fibers was normal to the sliding surface. In Kevlar-epoxy composites when the fibers were oriented normal to the surface and the sliding direction, the wear rate was also minimum but the friction coefficient was the highest. In glass fiber-MoS₂-PTFE composites wear was minimum when the largest fraction of fibers was oriented normal to the sliding surface.     

Studies of high temperature sliding wear of metallic dissimilar interfaces III: Incoloy MA956 versus Incoloy 800HT

Wear variations of Incoloy MA956 slid against Incoloy 800HT between room temperature and 750 °C, and sliding speeds of 0.314, 0.654 and 0.905 m s⁻¹ were investigated using a ‘reciprocating block-on-cylinder’ (low debris retention) configuration.Three forms of wear depending largely on sliding temperature were observed: ‘severe wear’ with high transfer between room temperature and 270 °C, ‘severe wear’ with low transfer between 390 and 570 °C and ‘glaze formation’ (retarded by increased sliding speed) at 630 °C and above. The differences in wear behaviour are discussed, with wear behaviour mapped and wear surfaces at 750 °C (0.314 and 0.905 m s⁻¹) cross-sectioned and profiled.     

Influence of counter surface topography on the tribological behavior of carbon-filled PPS composites in water

This study is aimed at investigating the influence of counter surfaces׳ topography on tribological behavior of several carbon-filled polyphenylene sulfide (PPS) composites in water lubricated contacts. The results of this study showed significant increase in wear rate of pure, graphite and/or multi-walled carbon nanotubes filled PPS composites with increase in mean slope of profile along the sliding direction (Δα_y). This is while SCF filled PPS composites exhibited 1–3 orders of magnitude lower wear rate with little dependence on counter surface roughness characteristics. Among the roughness parameters studied, R_pk and lay orientation played a more significant role in friction, and R_pk and Δα_y were found to correlate best with the wear rate of the composites not containing SCF in their matrices.     

An investigation on worn surfaces of chopped glass fibre reinforced polyester through SEM observations

The wear mechanisms of chopped strand mat (CSM) glass fibre reinforced polyester (CGRP) composite subjected to dry sliding against smooth stainless steel counterface (R_a=0.06 μm) were studied using a pin-on-disc technique. The effects of normal load (30-90 N), sliding velocity (2.8-3.9 m/s) and sliding distance (0.7-3.5 km) on friction and wear behaviour of the CGRP composite in two different CSM orientations (parallel and anti-parallel) were measured. The worn surfaces of the CGRP composite specimens for each specific test condition were examined using scanning electron microscopy (SEM).Sliding in P-orientation exhibited lower friction coefficient at lower load and higher speed compared to AP-orientation. Meanwhile, sliding in AP-orientation exhibited (15%) less friction coefficient at higher load compared to P-orientation. At higher range of all tested parameters, AP-orientation exhibited less mass loss (16%) compared to the P-orientation.Interestingly, SEM observations showed various wear mechanisms that predominated by abrasive nature. Damage of different features in the matrix and CSM glass fibre associated with higher values of load, speed, and sliding distance such as micro- and macro-cracks in the matrix, interface separation, fibre debonding and fracture, and different sizes of fractured fibres were evident.     

Influence of secondary phases on the tribological response of electro-discharge machined zirconia-based composites against WC-Co cemented carbide

Three ceramic composite grades, consisting of a ZrO₂ matrix and 40 vol.% WC, TiC_0.5N_0.5 or TiN phase, were completely self-developed by hot pressing powder mixtures of yttria-stabilised zirconia (Y-TZP) and distinctive WC, TiC_0.5N_0.5 or TiN powder sources. The friction and wear characteristics of the zirconia-based composites against WC-Co cemented carbide were investigated by performing dry reciprocating sliding experiments on a pin-on-plate tribometer under various normal contact forces. The generated wear was quantified using surface scanning topography. Post-mortem obtained wear volumes were correlated to real-time recorded wear depth. The ZrO₂-40 vol.% WC grade displayed more favorable tribological properties compared to the other grades with equal secondary phase content. The worn surfaces and the wear debris were analysed by scanning electron microscopy (SEM) and energy dispersive X-ray analysis (EDX), revealing several wear mechanisms such as polishing, abrasion and wear debris layer formation, mainly depending on the imposed contact load and the material composition.     

Sliding tribological behavior of AlCrN coating

The sliding tribological behavior of the PVD AlCrN coating against Si₃N₄ ball have been investigated by using the CETR multi-functional UMT-2 test system under two sliding conditions (bidirectional and unidirectional). Reciprocating sliding tests (bidirectional) were performed under varied normal loads (5, 10 and 20 N) at sliding velocity of 0.48 m/min. Ball-on-disc tests (unidirectional) were performed at varied sliding velocities (0.48 and 5 m/min) under normal load of 5 N. The wear scars of the coating were evaluated by surface profilometer, scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDX), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS), and the sliding wear mechanism of the coating was consequently discussed. The results showed that AlCrN coating had excellent anti-abrasion properties. Both the normal load in reciprocating sliding test and the sliding velocity in ball-on-disc test had significant influence on the sliding tribological behavior of the AlCrN coating. The combination of abrasion and oxidation was the main sliding wear mechanism for the AlCrN coating. The wear resistant and thermally stable oxides formed by the tribo-chemical reactions of chromium and aluminum protected the AlCrN coating against wear admirably.     

Tribological Behavior of PTFE Composites Filled with PEEK and Nano-Al2O3

In this study, the tribological properties of polytetrafluoroethylene (PTFE) composites filled with polyetheretherketone (PEEK) and nano-Al₂O₃ particles were studied using a block-on-ring wear tester. The tribological performance of the composites was affected by the experimental parameters (sliding speed, normal load, and environmental temperature) and the composites achieved a high-speed sliding friction state. The results showed that the PEEK and nano-Al₂O₃ particles significantly improved the wear resistance of the PTFE composites. In addition, the nano-Al₂O₃ particles increased the hardness of the composites and enhanced the mechanical properties to enable applications in a wider range of industrial fields. The effects of the sliding speed and normal load on the tribological properties were more significant than that of the environmental temperature. In addition, the entire wear process was divided into three stages (the initial wear stage, severe wear transition stage, and ultralow stable wear stage), according to the evolution of the tribological characteristics (wear rate, morphology of the worn surface and transfer film, and wear debris morphology).     

Wear properties of Saffil/Al,Saffil/Al2O3/Al and Saffil/SiC/Al hybrid metal matrix composites

The purpose of this study is to investigate the wear properties of Saffil/Al, Saffil/Al₂O₃/Al and Saffil/SiC/Al hybrid metal matrix composites (MMCs) fabricated by squeeze casting method. Wear tests were done on a pin-on-disk friction and wear tester under both dry and lubricated conditions. The wear properties of the three composites were evaluated in many respects. The effects of Saffil fibers, Al₂O₃ particles and SiC particles on the wear behavior of the composites were elucidated. Wear mechanisms were analyzed by observing the worn surfaces of the composites. The variation of coefficient of friction (COF) during the wear process was recorded by using a computer. Under dry sliding condition, Saffil/SiC/Al showed the best wear resistance under high temperature and high load, while the wear resistances of Saffil/Al and Saffil/Al₂O₃/Al were very similar. Under dry sliding condition, the dominant wear mechanism was abrasive wear under mild load and room temperature, and the dominant wear mechanism changed to adhesive wear as load or temperature increased. Molten wear occurred at high temperature. Compared with the dry sliding condition, all three composites showed excellent wear resistance when lubricated by liquid paraffin. Under lubricated condition, Saffil/Al showed the best wear resistance among them, and its COF value was the smallest. The dominant wear mechanism of the composites under lubricated condition was microploughing, but microcracking also occurred to them to different extents.