Effect of transfer film structure, composition and bonding on the tribological behavior of polyphenylene sulfide filled with nano particles of TiO2, ZnO, CuO and SiC

The tribological behavior of polyphenylene sulfide (PPS) filled with inorganic nano particles was studied. The fillers investigated were TiO₂, ZnO, CuO and SiC whose sizes varied from 30 to 50 nm. The polymer composites were compression molded with varying proportions of these fillers. Wear and friction tests were performed in a pin-on-disk configuration at a sliding speed of 1.0 m/s, nominal pressure of 0.65 MPa, and counterface roughness of 0.10 μm Ra. The polymer composite pins slid against hardened tool steel counterfaces. The transfer films of the composite materials formed on the counterfaces during sliding were studied by optical microscopy and X-ray photoelectron spectroscopy (XPS) and the adhesion between the transfer film and counterface was measured in terms of the peel strength. It was found that the wear rate of PPS decreased when TiO₂ and CuO were used as the fillers but increased with ZnO and SiC fillers. The optimum wear resistance was obtained with 2 vol.% CuO or TiO₂. These filled composites had the coefficients of friction lower than that of the unfilled PPS. The wear behavior of the composites is explained in terms of the topography of transfer film and adhesion of transfer film to the counterface as observed from peel strength studies. There is a good correlation observed between the transfer film-counterface bond strength and wear resistance.     

Friction and wear properties of bronze–graphite composite under water lubrication

Bronze–graphite composite was prepared using powder metallurgy. The friction and wear behaviors of the resulting composites in dry- and water-lubricated sliding against a stainless steel were comparatively investigated on an MM-200 friction and wear tester in a ring-on-block contact configuration. The wear mechanisms of the bronze–graphite composite were discussed based on examination of the worn surface morphologies of both the composite block and the stainless steel ring by means of scanning electron microscopy equipped with an energy dispersion spectrometry and on determination of some typical elements on the worn surfaces by means of X-ray photoelectron spectroscopy. It was found that the friction coefficient was higher under water lubrication than that under dry sliding and it showed margined change with increasing load under the both sliding conditions. A considerably decreased wear rate of the bronze–graphite composite was registered under water-lubricated sliding than under dry sliding, though it rose significantly at a relatively higher load. This was attributed to the hindered transfer of the composite onto the counterpart steel surface under water-lubricated sliding and the cooling effect of the water as a lubricant, while its stronger transfer onto the steel surface accounted for its higher wear rate under dry sliding. Thus, the bronze–graphite composite with much better wear-resistance under water-lubricated sliding than under dry sliding against the stainless steel could be a potential candidate as the tribo-material in aqueous environment.     

A study of the thermal,dynamic mechanical,and tribological properties of polyphenylene sulfide composites reinforced with carbon nanofibers

The thermal, dynamic mechanical, and tribological properties of polyphenylene sulfide (PPS) composites reinforced with carbon nanofiber (CNF) were studied. Dynamic mechanical thermal analysis (DMTA) and differential scanning calorimetry (DSC) were used to study the viscoelastic properties and thermal transitions. In order to study the tribological properties, friction and wear tests in a pin-on-disk configuration were performed. The changes in melting point, crystallization temperature, and glass transition temperature were found to be small as a result of reinforcement. Steady state wear rates of the reinforced composites sliding against the counterface of roughness 0.13–0.15 μm Ra were significantly lower than that of the unreinforced PPS. When the composites were tested against the smoother counterface of 0.06–0.11 μm Ra, the wear rates were higher. The coefficient of friction in all the cases was not practically affected by the presence of CNF. The transfer films formed on the counterface during sliding were examined by optical microscopy and atomic force microscopy (AFM). The variation of wear is discussed in terms of the texture and topography of transfer film.     

An investigation of the transfer film characteristics and the tribological behaviors of polyphenylene sulfide composites in sliding against tool steel

The effect of CuS, CuO, CaF₂, and ZnF₂ fillers in particulate sizes of 200–350 mesh on the friction and wear behavior of polyphenylene sulfide (PPS) was investigated. The filler proportion studied was 35 vol.%. The specimens which were prepared by compression molding were tested for friction and wear in a pin-on-disc configuration using hardened tool steel disc as the counterface. The morphologies of the worn surfaces and the transfer films were studied by scanning electron microscopy and the transfer films were analyzed by energy dispersive spectroscopy. The improvement in wear resistance with CuS was considerable and with CuO marginal, while the wear resistance decreased with CaF₂ and ZnF₂. The coefficient of friction increased significantly with CuO and decreased with CaF₂ and was not significantly affected by the other fillers. The changes in the friction and wear behaviors were analyzed in terms of the morphology and the composition of transfer films.     

Friction and Wear Behavior of Ultra-High Molecular Weight Polyethylene Sliding Against GCr15 Steel and Electroless Ni–P Alloy Coating Under the Lubrication of Seawater

The friction and wear behavior of ultra-high molecular weight polyethylene (UHMWPE) sliding against GCr15 steel and electroless Ni-P alloy coating under the lubrication of seawater was investigated and compared with that under dry sliding and lubrication of pure water and 3.5 wt.% NaCl solution, respectively. It was found that under the lubrication of aqueous medium, the friction and wear behavior of UHMWPE mainly depended on the corrosion of counterface and the lubricating effect of the medium. Because of serious corrosion of counterface by the medium, the wear rates of UHMWPE sliding against GCr15 under the lubrication of seawater and NaCl solution were much larger than that under other conditions, and such a kind of wear closely related to the corrosion of counterface can be reckoned as indirect corrosive wear. However, when sliding against corrosion-resistant Ni–P alloy under the lubrication of seawater, the lowest coefficient of friction and wear rate of UHMWPE were obtained, owing to superior lubricating effect of seawater. Moreover, periodic ripple patterns were observed on the worn surfaces of UHMWPE sliding against GCr15 under the lubrication of seawater and NaCl solution, which were ascribed to the intelligent reconstruction of surface microstructure of UHMWPE upon large plowing effect of the counterface asperities. Based on scanning electron microscopic (SEM) and three-dimensional (3D) profile analyses of the worn surfaces of UHMWPE, a stick–slip dynamic mechanism was proposed to illustrate the pattern abrasion of UHMWPE. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Investigation of the Transition State in the Wear of Polyphenylene Sulfide Sliding Against Steel

The effect of sliding variables, including counterface roughness, sliding speed, and contact pressure, on the run-in state of wear and friction was studied. Sliding was performed in the pin-on-disk configuration with a polyphenylene sulfide (PPS) pin resting on the flat steel counterface. Some experiments were also run to study the effect of air cooling and heating. Optical microscopy and scanning electron microscopy were used to study the shape and size of the wear debris, worn pin surface, and the transfer film formed on steel counterfaces. It was found that friction and wear in the run-in state were significantly affected by the sliding variables studied and their influence was closely related to the development of a transfer film during the run-in state. If the transfer film developed during initial sliding, the coefficient of friction increased and wear rate decreased. The wear rate in the run-in state increased with the increase in initial counterface roughness and there was an optimal counterface roughness of 0.06 m Ra for minimum steady state wear rate. A higher applied load led to a higher wear rate in the run-in state but that was not the case with steady state wear rate.     

The role of transfer film and back transfer behavior on the tribological performance of polyoxymethylene in sliding

The role of transfer films formed during the sliding of polymer composites against steel counterfaces was studied in terms of the tribological behaviors of the composites. The composites were prepared by compression molding and sliding tests were run in pin-on-disk sliding configuration. The counterface was made of tool steel hardened to 55–60 HRC and finished to a surface roughness of 0.09–0.10 μm Ra. Wear tests were run for 6 hrs at the sliding speed of 1.0 m/s and contact pressure of 0.65 MPa. Transfer films formed on the counterfaces during sliding were investigated using Atomic Force Microscopy (AFM) and Scanning Electron Microscopy (SEM). The results showed that as the transfer film became smooth and uniform, the wear rate decreased. The examination of worn surfaces using Energy Dispersive Spectroscopy (EDS: dot mapping mode) showed the back-transfer of the steel counterface material to the polymer pin surface. This behavior is believed to strengthen the polymer pin surface during sliding thereby contributing to the decrease in wear rate. This paper was recommended for publication in revised form by Associate Editor Jae Cheon Lee Minhaeng Cho received his B.S. and M.S. degrees in Mechanical Engineering from Chung-Ang University, Seoul in 1993 and 1995, respectively. He received his M.S. degree in Materials Science and Engineering from Oregon State University in 2000, and his Ph.D. in Mechanical Engineering from Iowa State University in 2004. Dr. Cho is currently an Assistant Professor at the School of Mechanical Engineering at Chung-Ang University in Seoul, Korea. His research interests are in the area of tribology, surface phenomena, and functional surfaces such as laser surface texturing and ultra-thin coatings.     

弹性金属塑料复合材料的摩擦磨损特性研究

在MPX-2000摩擦磨损试验机上，用环盘摩擦副，结合扫描电镜分别评价了弹性金属塑料（EMP）复合材料与钢在油润滑和干摩擦条件下的摩擦磨损特性。结果表明：两种试验条件下，相同滑动速度的摩擦系数随载荷的升高而减小，当载荷为2000N，滑动速度小于3.52m/s时，摩擦系数基于趋于稳定，EMP磨损率随滑动速度和载荷的升高耐增加，但不同试验条件的增幅不高，油润滑下滑动速度小于3.52m/s和干摩擦条件下滑动速度小于1.96m/s时，EMP以微切削，塑性变形和梨沟磨损为主，并在摩擦副两表面形成转移物。     

Friction and wear characteristics of lead and its compounds filled polytetrafluoroethylene composites under oil lubricated conditions

The friction and wear properties of Pb, PbO, Pb₃O₄, or PbS filled polytetrafluoroethylene (PTFE) composites sliding against GCr15 bearing steel under both dry and liquid paraffin lubricated conditions were studied by using an MHK-500 ring-block wear tester. The worn surfaces and the transfer films of these PTFE composites formed on the surface of GCr15 bearing steel were then investigated by using a scanning electron microscope (SEM) and an optical microscope, respectively. Experimental results show that filling Pb, PbO, Pb₃O₄ or PbS to PTFE can greatly reduce the wear of the PTFE composites, but the wear reducing action of Pb₃O₄ is the most effective. Meanwhile, PbS increases the friction coefficient of the PTFE composite, but Pb and Pb₃O₄ reduce the friction coefficients of the PTFE composites. However, the friction and wear properties of lead or its compounds filled PTFE composites can be greatly improved by lubrication with liquid paraffin, and the friction coefficients of the PTFE composites can be decreased by one order of magnitude. Optical microscope investigation of transfer films shows that Pb, PbO, Pb₃O₄ and PbS enhance the adhesion of the transfer films to the surface of GCr15 bearing steel, so they greatly reduce the wear of the PTFE composites. However, the transfer of the PTFE composites onto the surface of GCr15 bearing steel can be greatly reduced by lubrication with liquid paraffin, but the transfer still takes place. SEM examination of worn surfaces shows that the interaction between liquid paraffin and the PTFE composites creates some cracks on the worn surfaces of the PTFE composites; the creation and development of the cracks reduces the load-carrying capacity of the PTFE composites, and this leads to deterioration of the friction and wear properties of the PTFE composites filled with lead or its compounds under higher loads in liquid paraffin lubrication.     

Impact of Viscoelasticity on the Tribological Behavior of PTFE Composites for Valve Seals Application

In this article, we studied and explored the impact of viscoelasticity on the friction and wear behavior of pure polytetrafluoroethylene (PTFE), carbon–graphite PTFE composite, and glass fiber–MoS₂ PTFE composite. Tests were carried out using a specific reciprocating tribometer for valve seal application. The worn surfaces of the PTFE composites and the transfer films formed on the counterface were examined with a scanning electron microscope (SEM). Experimental results revealed that the addition of filler materials was effective in reducing the wear volume in all composites studied. In addition, the friction coefficient and wear resistance showed high sensitivity to the viscoelastic behavior of the PTFE seal. SEM investigation showed that the incorporation of particulate fillers into the PTFE matrix could dramatically reduce and stabilize the transfer films to the counterface, so they largely decreased the wear of the PTFE composites.     

聚四氟乙烯碳纤维增强双马来酰亚胺复合材料的摩擦学性能

研究了不同含量PTFE碳纤维增强双马来酰亚胺复合材料的力学和摩擦学性能,并分析了在干摩擦和水润滑条件下的磨损表面形貌和磨损机制。结果表明:添加质量分数10%~15%PTFE的复合材料体系机械性能最佳,随PTFE含量的增加,复合材料的摩擦因数下降,而磨损率呈上升趋势。水润滑下,摩擦因数和磨损率比干摩擦下都有相应的降低。干摩擦下,材料的磨损主要以塑性变形、微观破裂及破碎为主;水润滑下,这一机制明显减弱,主要表现为微切削形态。     

Tribological properties of metal-plastic multilayer composites under oil lubricated conditions

Three kinds of metal-plastic multilayer composites, which were composed of a steel backing, a middle layer of sintered porous bronze and a surface layer of polytetrafluoroethylene (PTFE) filled by Pb or Cu₂O powders, were prepared. The friction and wear properties as well as the limiting pressure times velocity (PV) values of these metal-plastic multilayer composites sliding against 45 carbon steel under both dry and oil lubricated conditions were evaluated on a MPV-1500 friction tester with a steel axis rotating on a journal bearing. The worn surfaces of these metal-plastic multilayer composites and the transfer films formed on the surface of steel axis were examined by electron probe microscopy analysis (EPMA). Experimental results show that filling of Pb to PTFE reduces the friction coefficient and wear of the composite, while filling of Cu₂O to PTFE increases the friction coefficient but decreases the wear of the composite. The friction and wear properties as well as the limiting PV values of these metal-plastic multilayer composites can be greatly improved with the oil lubrication. EPMA investigations show that Pb and Cu₂O fillers preferentially transfer onto the surfaces of steel axis, which may enhance or deteriorate the adhesion between transfer films and steel surfaces. Meanwhile the transfer of these metal-plastic multilayer composites onto the steel surface can be greatly reduced with oil lubrication, which results in the remarkable decrease of the wear of these metal-plastic multilayer composites.     

Friction and wear properties of metal powder filled PTFE composites under oil lubricated conditions

Four kinds of polytetrafluoroethylene (PTFE)-based composite, pure PTFE, PTFE+30vol.%Cu, PTFE+30vol.%Pb and PTFE+30vol.%Ni composite, were prepared. The friction and wear properties of these metal powder filled PTFE composites sliding against GCr15 bearing steel under both dry and lubricated conditions were studied using an MHK-500 ring-block wear tester. The worn surfaces of the PTFE composites and the transfer films formed on the surface of GCr15 bearing steel were examined using scanning electron microscopy (SEM) and optical microscopy respectively. Experimental results show that the friction and wear properties of the PTFE composites can be greatly improved by liquid paraffin lubrication. The wear of these PTFE composites can be decreased by at least 1 to 2 orders of magnitude compared with that under dry friction conditions, while the friction coefficients can be decreased by 1 order of magnitude, SEM and optical microscopy investigations of the rubbing surfaces show that metal fillers of Cu, Pb and Ni not only raise the load carrying capacity of the PTFE composites, but also promote transfer of the PTFE composites onto the counterfaces, so they greatly reduce the wear of the PTFE composites. However, the transfer of these PTFE composites onto the counterfaces can be greatly reduced by liquid paraffin lubrication, but transfer still takes place.     

Tribological Behavior of Micrometer- and Submicrometer-Size Cenosphere Particulate-Filled Glass Fiber–Reinforced Vinylester Composites Under Dry and Water-Lubricated Sliding Conditions

In this work, the tribological behavior of micrometer and submicrometer cenosphere particulate–filled E-glass fiber–reinforced vinylester composites have been investigated on a pin-on-disc tester under dry sliding and water-lubricated sliding conditions. Three different uniform sizes of cenosphere particles (2 μm, 900 nm, 400 nm) were used as fillers in the glass fiber–reinforced vinylester composites. The weight fraction of cenosphere particles has been varied in the ranges from 5, 10, 15, to 20 wt%. The experimental results show that all of the composites exhibited lower coefficient of friction and lower wear resistance under water-lubricated sliding conditions than under dry sliding. It has been noted that the submicrometer size (400 nm) cenosphere particulates as fillers contributed significantly to improve the wear resistance. It has also been noted that 10 wt% of the cenosphere particles is the most effective in reducing the wear rate and coefficient of friction. Effects of various wear parameters such as applied normal loads, sliding speeds, particle size, and particle content on the tribological behavior were also discussed. In order to understand the wear mechanism, the morphologies of the worn surface were analyzed by means of scanning electron microscopy (SEM) for composite specimens under both dry and water-lubricated sliding conditions.     

Transfer film bonding and wear studies on CuS-nylon composite sliding against steel

The tribological behaviour of nylon 11 reinforced with lead sulphide filler was studied. The composite specimens with different filler proportions were made by compression moulding. The friction and wear experiments were run under ambient conditions in a pin-on-disk machine with the composite pin riding on the flat surface of a steel disk. It was found that 35 vol.% PbS-nylon composite had the highest wear resistance. The friction and wear tests were run with this composite at different loads, speeds and counterface roughnesses. The wear rate increased considerably when the load was increased from 19.6 N to 39.2 N and the sliding speed from 1 m/s to 2 m/s, but the effect of these increases on the coefficient of friction was very small. The wear rate also increased abruptly when the surface roughness was increased from 0.11 to 0.3 μm but the coefficient of friction was not affected. It was found that the wear process was dominated by the transfer film that formed on the counterface. The transfer film and the worn surfaces were studied by scanning electron microscopy. XPS analysis indicated chemical bonding between the polymer composite transfer film and the steel counterface.     

Tribological behaviours of PA/UHMWPE blend under dry and lubricating condition

Dry-sliding and lubricated friction and wear behaviours of polyamide (PA) and ultra-high molecular weight polyethylene (UHMWPE) blend were studied using a pin-on-disc method (polymer pin sliding against a stainless steel disc) at room environment. The tribological performance of PA and UHMWPE were also investigated for the purpose of comparison. The worn surfaces were examined using a scanning electron microscope (SEM) and optical microscope. It was observed that PA specimen demonstrated highest friction coefficient, UHMWPE the lowest in both dry-sliding and lubricated sliding test. The friction of PA could be sufficiently decreased by blending with UHMWPE. Statistical analysis suggested the relationship between the wear volume loss and the sliding distance could be expressed by a linear model for dry-sliding, while a logarithmic model was determined for lubricated sliding. The difference in wear modes between both sliding series suggested that there was change in the mode of material removal process. The lower wear rate in lubricated sliding was attributed to the elastohydrodynamic or partial elastohydrodynamic lubrication through the development of a continuous lubricant film between the polymer and the counterface, while the high wear rate of the specimens, in dry-sliding test, was mainly caused by fatigue process due to the repeated action of tearing and crack-propagation.     

HIP-Si3N4陶瓷/45#钢副干摩擦和水润滑下摩擦学性能

利用MPX-2000型盘销式摩擦磨损试验机考察了HIP—Si3N4陶瓷／45^#钢副在干摩擦和水润滑下的摩擦磨损性能；用扫描电子显微镜观察了试件表面的磨损状态；采用X射线电子能谱仪分析了摩擦表面的化学成分：结果表明：干摩擦条件下，HIP—Si3N4陶瓷的磨损速率比45^#钢小，45^#钢发生粘着磨损，HIP—Si3N4陶瓷发生了脆性断裂和脱落；水润滑条件下，摩擦表面产生了Si(OH)4反应膜，降低了磨损，主要是化学腐蚀磨损。     

Wear behavior of graphite-fiber-reinforced glass

Composites of borosilicate glass reinforced with high strength, high modulus and ultrahigh modulus (UHM) graphite fibers were tested for wear against a cast iron counterface in a pin-on-disk configuration at sliding velocities of 0.24, 0.60 and 0.96 m s^?1 under a load of 5 MPa.Discontinuous fiber-reinforced composites generally exhibited higher wear rates and friction coefficients than the continuous fiber-reinforced systems. Continuous UHM fiber-reinforced pins exhibited the lowest wear rate. It is shown that the wear rate depends on the strength and dimensions of the graphite filaments.Two types of wear, mild and severe, were observed at low and high sliding velocities. Mild wear is characterized by a smooth thin stable film on both the pin and the counterface with minimal pitting and plastic deformation of the cast iron. Severe wear is characterized by rough pitted surfaces on the pin and the counterface accompanied by a thick film on the counterface. A proposed mechanism of wear of unidirectional graphite-fiber-reinforced composites which incorporates the transition between mild and severe wear can explain the phenomenological observations.     

Tribological behavior of graphite-containing nickel-based composite as function of temperature,load and counterface

Nickel-based graphite-containing composites were prepared by powder metallurgy method. Their mechanical properties at room temperature and friction and wear properties from room temperature to 600 °C were investigated by a pin-on-disk tribometer with alumina, silicon nitride and nickel-based alloy as counterfaces. The effects of graphite addition amount, temperature, load, sliding speed and counterface materials on the tribological properties were discussed. The micro-structure and worn surface morphologies were analyzed by scanning electron microscope (SEM) attached with energy dispersive spectroscopy (EDS). The results show that the composites are mainly consisted of nickel-based solid solution, free graphite and carbide formed during hot pressing. The friction and wear properties of composites are all improved by adding 6–12 wt.% graphite while the anti-bending and tensile strength as well as hardness decrease after adding graphite. The friction coefficients from room temperature to 600 °C decrease with the increase of load, sliding speed while the wear rates increase with the increasing temperature, sliding speed. The lower friction coefficients and wear rates are obtained when the composite rubs against nickel-based alloy containing molybdenum disulfide. Friction coefficients of graphite-containing composites from room temperature to 600 °C are about 0.4 while wear rates are in the magnitude of 10^?5 mm³/(N m). At high temperature, the graphite is not effective in lubrication due to the oxidation and the shield of ‘glaze’ layer formed by compacting back-transferred wear particles. EDS analysis of worn surface shows that the oxides of nickel and molybdenum play the main role of lubrication instead of graphite at the temperature above 400 °C.     

The tribological characteristics of JS material under lubrication of oil

A material composed of a steel backing, a sintered porous bronze middle layer and a layer of reinforced PTFE, which is named JS material, was prepared. The friction, wear and limiting PV values of this material under dry friction as well as the lubrication of number 20 mechanical oil were studied using a MPV-1500 friction tester. The worn surface of JS material and the transfer film formed on the counterface of carbon steel were investigated using scanning electron microscopy (SEM) and electron probe microanalysis (EPMA). The results show that the friction, wear and limiting PV values of JS material can be greatly improved with the lubrication of oil. The results of SEM and EPMA analyses indicate that, under dry friction conditions, the solid lubricant PTFE and Pb easily transfer to the steel counterface and results in the reduction of friction and wear; while under the lubrication of oil, little transference of PTFE and Pb to the steel surface occurs and very small friction and wear are achieved. Analyses of frictional surfaces also suggest that the Pb filler gets enrichment on the rubbing surfaces, which is beneficial in increasing the adhesion of the transfer film with the steel surface.