Experimental study of the effects of vegetable oil methyl ester on DI diesel engine performance characteristics and pollutant emissions

Vegetable oil methyl ester (VOME) is produced through the transesterification of vegetable oil and can be used as biodiesel in diesel engines as a renewable, nontoxic, and potentially environmentally friendly fossil fuel alternative in light of growing concerns regarding global warming and increasing oil prices. This study used VOME fuels produced from eight commonly seen oil bases to conduct a series of engine tests to investigate the effects of VOME on the engine performance, exhaust emissions, and combustion characteristics. The experimental results showed that using VOME in an unmodified direct injection (DI) diesel engine yielded a higher brake specific fuel consumption (BSFC) due to the VOME fuel’s lower calorific value. The high cetane number of VOME also imparted a better ignition quality and the high intrinsic oxygen content advanced the combustion process. The earlier start of combustion and the rapid combustion rate led to a drastic increase in the heat release rate (HRR) and the in-cylinder combustion pressure (ICCP) during the premixed combustion phase. A higher combustion rate resulted in higher peaks of HRR and ICCP as well as near the top dead center (TDC) position. Thus, it was found that a diesel engine fueled with VOME could potentially produce the same engine power as one fueled with petroleum diesel (PD), but with a reduction in the exhaust gas temperature (EGT), smoke and total hydrocarbon (THC) emissions, albeit with a slight increase in nitrogen oxides (NO_x) emissions. In addition, the VOME which possesses shorter carbon chains, more saturated bonds, and a higher oxygen content also yields a lower EGT as well as reduced smoke, NO_x, and THC emissions. However, this is obtained at the detriment of an increased BSFC.     

Utilization of unattended methyl ester of paradise oil as fuel in diesel engine

Engine tests have been carried out with the aim of obtaining the performance, emission and combustion characteristics of a diesel engine running on methyl ester of paradise oil (MEPS) and its diesel blends. From the emission analysis it was found that there was a significant reduction in smoke and hydrocarbon emissions by 33% and 22% respectively for MEPS 50 blend and 40% and 27% reductions for MEPS 100. However, there was an increase of 5% and 8% NO_x emission for MEPS 50 and MEPS 100 respectively. Brake thermal efficiencies of MEPS and its diesel blends are slightly lower than that of std. diesel. From the engine analysis, it was found that the performance of MEPS and its diesel blends were similar to that of std. diesel.     

Study of the performance,emission and combustion characteristics of a diesel engine using poon oil-based fuels

Experiments were conducted to study the performance, emission and combustion characteristics of a DI diesel engine using poon oil-based fuels. In the present work, poon oil and poon oil methyl ester are tested as diesel fuels in Neat and blended forms. The blends were prepared with 20% poon oil and 40% poon oil methyl ester separately with standard diesel on a volume basis. The reductions in smoke, hydrocarbon and CO emissions were observed for poon oil methyl ester and its diesel blend along with increased NO_x emission compared to those of standard diesel. However, a reduction in NO_x emission and an increase in smoke, hydrocarbon and CO emissions were observed for Neat poon oil and its diesel blend compared to those of standard diesel. The 40% poon oil methyl ester blend showed a 2% increase in brake thermal efficiency compared to that of standard diesel, whereas other fuels tested showed a decreasing trend. From the combustion analysis it was found that ignition delay was shorter for all fuels tested compared to that of standard diesel. The combustion characteristics of poon oil methyl ester and its diesel blend closely followed those of standard diesel.     

Study of oxygenated biomass fuel blends on a diesel engine

Vegetable methyl ester was added in ethanol–diesel fuel to prevent separation of ethanol from diesel in this study. The ethanol blend proportion can be increased to 30% in volume by adding the vegetable methyl ester. Engine performance and emissions characteristics of the fuel blends were investigated on a diesel engine and compared with those of diesel fuel. Experimental results show that the torque of the engine is decreased by 6%–7% for every 10% (by volume) ethanol added to the diesel fuel without modification on the engine. Brake specific fuel consumption (BSFC) increases with the addition of oxygen from ethanol but equivalent brake specific fuel consumption (EBSFC) of oxygenated fuels is at the same level of that of diesel. Smoke and particulate matter (PM) emissions decrease significantly with the increase of oxygen content in the fuel. However, PM reduction is less significant than smoke reduction. In addition, PM components are affected by the oxygenated fuel. When blended fuels are used, nitrogen oxides (NO_x) emissions are almost the same as or slightly higher than the NO_x emissions when diesel fuel is used. Hydrocarbon (HC) is apparently decreased when the engine was fueled with ethanol–ester–diesel blends. Fuelling the engine with oxygenated diesel fuels showed increased carbon monoxide (CO) emissions at low and medium loads, but reduced CO emissions at high and full loads, when compared to pure diesel fuel.     

Performance, emission and combustion characteristics of poon oil and its diesel blends in a DI diesel engine

Experimental tests have been carried out to evaluate the performance, emission and combustion characteristics of a diesel engine using Neat poon oil and its blends of 20%, 40%, and 60%, and standard diesel fuel separately. The common problems posed when using vegetable oil in a compression ignition engine are poor atomization; carbon deposits, ring sticking, etc. This is because of the high viscosity and low volatility of vegetable oil. When blended with diesel, poon oil presented lower viscosity, improved volatility, better combustion and less carbon deposit. It was found that there was a reduction in NO_x emission for Neat poon oil and its diesel blends along with a marginal increase in HC and CO emissions. Brake thermal efficiency was slightly lower for Neat poon oil and its diesel blends. From the combustion analysis, it was found that poon oil-diesel blends performed better than Neat poon oil.     

A rapid test to measure performance,emission and wear of a diesel engine fueled with palm oil diesel

Results of performance, emission and tribological evaluations of palm oil methyl ester and its blends with conventional diesel in an automobile diesel engine test bed are presented. Polymerization and carbon deposits on the fuel injector were monitored. CO, CO₂, O₂, combustion efficiency and temperature of exhaust gases were also measured. Palm oil methyl ester and its blends have great potential as alternative diesel fuel. Performance and exhaust gas emission for palm oil methyl ester and its blends with conventional diesel are comparable with those of conventional diesel fuel. Palm oil methyl ester does not pose a severe environmental problem and will not deteriorate engine and bearing components.     

Experimental investigation on a C.I. engine using orange oil and orange oil with DEE

In the present work, the effect of using neat orange oil, optimum orange oil-diesel blend and the optimum flow rate of DEE with orange oil are evaluated for the performance, emissions and combustion characteristics of a single cylinder, diesel engine. The experimental results show that carbon monoxide (CO), hydrocarbon (HC) and smoke emissions decrease while oxides of nitrogen (NO_x) emissions increase for orange oil and its blends compared to diesel fuel and DEE with orange oil. The brake thermal efficiency in the case of DEE with orange oil is higher than that of orange oil, orange oil-diesel fuel blend and diesel fuel. The peak cylinder pressure and heat release rate for DEE with orange oil are higher than those of diesel fuel operation.     

Combustion, performance and emission characteristics of a DI diesel engine fueled with ethanol-biodiesel blends

In this study, Euro V diesel fuel, biodiesel, and ethanol-biodiesel blends (BE) were tested in a 4-cylinder direct-injection diesel engine to investigate the combustion, performance and emission characteristics of the engine under five engine loads at the maximum torque engine speed of 1800 rpm. The results indicate that when compared with biodiesel, the combustion characteristics of ethanol-biodiesel blends changed; the engine performance has improved slightly with 5% ethanol in biodiesel (BE5). In comparison with Euro V diesel fuel, the biodiesel and BE blends have higher brake thermal efficiency. On the whole, compared with Euro V diesel fuel, the BE blends could lead to reduction of both NO_x and particulate emissions of the diesel engine. The effectiveness of NO_x and particulate reductions increases with increasing ethanol in the blends. With high percentage of ethanol in the BE blends, the HC, CO emissions could increase. But the use of BE5 could reduce the HC and CO emissions as well.     

Comparison of exhaust emissions and their mutagenicity from the combustion of biodiesel, vegetable oil, gas-to-liquid and petrodiesel fuels

Efforts are under way to reduce diesel engine emissions (DEE) and their content of carcinogenic and mutagenic polycyclic aromatic hydrocarbons (PAH). Previously, we observed reduced PAH emissions and DEE mutagenicity caused by reformulated or newly developed fuels. The use of rapeseed oil as diesel engine fuel is growing in German transportation businesses and agriculture. We now compared the mutagenic effects of DEE from rapeseed oil (RSO), rapeseed methyl ester (RME, biodiesel), natural gas-derived synthetic fuel (gas-to-liquid, GTL), and a reference petrodiesel fuel (DF) generated by a heavy-duty truck diesel engine using the European Stationary Cycle. Mutagenicity of the particle extracts and the condensates was tested using the Salmonella typhimurium mammalian microsome assay with strains TA98 and TA100. The RSO particle extracts increased the mutagenic effects by factors of 9.7 up to 17 in strain TA98 and of 5.4 up to 6.4 in strain TA100 compared with the reference DF. The RSO condensates caused up to three times stronger mutagenicity than the reference fuel. RME extracts had a moderate but significantly higher mutagenic response in assays of TA98 with metabolic activation and TA100 without metabolic activation. GTL samples did not differ significantly from DF. Regulated emissions (hydrocarbons, carbon monoxide, nitrogen oxides (NO_x), and particulate matter) remained below the limits except for an increase in NO_x exhaust emissions of up to 15% from the tested biofuels.     

Experimental investigation of mineral diesel fuel, GTL fuel, RME and neat soybean and rapeseed oil combustion in a heavy duty on-road engine with exhaust gas aftertreatment

The effects of mineral diesel fuel, gas-to-liquid fuel, rapeseed methyl ester, neat soybean and neat rapeseed oil on injection, combustion, efficiency and pollutant emissions have been studied on a compression ignition heavy duty engine operated near full load and equipped with a combined exhaust gas aftertreatment system (oxidation catalyst, particle filter, selective catalytic NO_x reduction). In a first step, the engine calibration was kept constant for all fuels which led to differences in engine torque for the different fuels. In a second step, the injection duration was modified so that all fuels led to the same engine torque. In a third step, the engine was recalibrated in order to keep the NO_x emissions at an equal level for all fuels (injection pressure, injection timing, EGR rate). The experiments show that the critical NO_x emissions were higher (even behind the exhaust gas aftertreatment systems) for oxygenated fuels in case of the engine not being recalibrated for the fuel. GTL and the oxygenated fuels show lower emissions for some pollutants and higher efficiency after recalibration to equal NO_x levels.     

Engine performance, exhaust emissions and combustion characteristics of a CI engine fuelled with croton megalocarpus methyl ester with antioxidant

The use of biodiesel as a substitute for petroleum-based diesel has become of great interest for the reasons of combating the destruction of the environment, the price of petroleum-based diesel and dependency on foreign energy sources. But for practical feasibility of biodiesel, antioxidants are added to increase the oxidation stability during long term storage. It is quite possible that these additives may affect the clean burning characteristics of biodiesel. This study investigated the experimental effects of antioxidants on the oxidation stability, engine performance, exhaust emissions and combustion characteristics of a four cylinder turbocharged direct injection (TDI) diesel engine fuelled with biodiesel from croton megalocarpus oil. The three synthetic antioxidants evaluated its effectiveness on oxidation stability of croton oil methyl ester (COME) were 1, 2, 3 tri-hydroxy benzene (Pyrogallol, PY), 3, 4, 5-tri hydroxy benzoic acid (Propyl Gallate, PG) and 2-tert butyl-4-methoxy phenol (Butylated Hydroxyanisole, BHA). The fuel sample tested in TDI diesel engine include pure croton biodiesel (B100), croton biodiesel dosed with 1000 ppm of an effective antioxidant (B100 + PY1000), B20 (20% croton biodiesel and 80% mineral diesel) and diesel fuel which was used as base fuel. The result showed that the effectiveness of the antioxidants was in the order of PY > PG > BHA. The brake specific fuel consumption (BSFC) of biodiesel fuel with antioxidants decreased more than that of biodiesel fuel without antioxidants, but both were higher than that of diesel. Antioxidants had few effects on the exhaust emissions of a diesel engine running on biodiesel. Combustion characteristics in diesel engine were not influenced by the addition of antioxidants in biodiesel fuel. This study recommends PY and PG to be used for safeguarding biodiesel fuel from the effects of autoxidation during storage. Overall, the biodiesel derived from croton megalocarpus oil can be utilized as partial substitute for mineral diesel.     

Physical-chemical properties of waste cooking oil biodiesel and castor oil biodiesel blends

This work presents the physical-chemical properties of fuel blends of waste cooking oil biodiesel or castor oil biodiesel with diesel oil. The properties evaluated were fuel density, kinematic viscosity, cetane index, distillation temperatures, and sulfur content, measured according to standard test methods. The results were analyzed based on present specifications for biodiesel fuel in Brazil, Europe, and USA. Fuel density and viscosity were increased with increasing biodiesel concentration, while fuel sulfur content was reduced. Cetane index is decreased with high biodiesel content in diesel oil. The biodiesel blends distillation temperatures T₁₀ and T₅₀ are higher than those of diesel oil, while the distillation temperature T₉₀ is lower. A brief discussion on the possible effects of fuel property variation with biodiesel concentration on engine performance and exhaust emissions is presented. The maximum biodiesel concentration in diesel oil that meets the required characteristics for internal combustion engine application is evaluated, based on the results obtained.     

Combustion performance and emissions of petrodiesel and biodiesels based on various vegetable oils in a semi industrial boiler

This paper intends to investigate combustion of petrodiesel and biodiesels of grape seed, corn, sunflower, soybean, olive and rice bran oils, which were produced through an alkali-based transesterification, in a non-pressurized, water-cooled combustion chamber by determining its combustion performance and gas emissions (CO, CO₂, NO_x, SO₂). First, the influence of fuel pressure which related to the rate of sprayed fuel to the chamber was studied in order to find out an optimum combustion pressure. In the next level, the influence of A/F upon emissions and boiler performances at 13.79 bars was studied. Results show that similar combustion of fuels occurred at 13.79 bars (optimum) where due to the increase in fuel pressure, the effect of viscous forces in flame formation disappeared. Complete combustion of fuels occurred at 19.305 bars where the CO emissions of all the fuels reached to zero.The overall performance of the boiler obtained with the methyl esters and petrodiesel are comparable for the defined operating points (especially at high energy rates and low A/F). All the six kinds of vegetable based methyl ester emitted lower emissions than petrodiesel over the wide fuel pressures, and A/F. Meanwhile, biodiesels emitted higher amounts of NO_x than petrodiesel. Biodiesels also emitted higher amounts of CO than petrodiesel at low fuel pressures when the viscous forces interfered with proper distributions of fuels to the combustion chamber.     

Comparative study of performance and emissions of a diesel engine using Chinese pistache and jatropha biodiesel

An experimental study of the performances and emissions of a diesel engine is carried out using two different biodiesels derived from Chinese pistache oil and jatropha oil compared with pure diesel. The results show that the diesel engine works well and the power outputs are stable running with the two selected biodiesels at different loads and speeds. The brake thermal efficiencies of the engine run by the biodiesels are comparable to that run by pure diesel, with some increases of fuel consumptions. It is found that the emissions are reduced to some extent when using the biodiesels. Carbon monoxide (CO) emissions are reduced when the engine run at engine high loads, so are the hydrocarbon (HC) emissions. Nitrogen oxides (NOx) emissions are also reduced at different engine loads. Smoke emissions from the engine fuelled by the biodiesels are lowered significantly than that fuelled by diesel. It is also found that the engine performance and emissions run by Chinese pistache are very similar to that run by jatropha biodiesel.     

An experimental investigation on a DI diesel engine using waste plastic oil with exhaust gas recirculation

Environmental degradation and depleting oil reserves are matters of great concern around the globe. Developing countries like India depend heavily on oil import of about 125 Mt per annum (7:1 diesel/gasoline). Diesel being the main transport fuel in India, finding a suitable alternative to diesel is an urgent need. In this context, waste plastic solid is currently receiving renewed interest. Waste plastic oil is suitable for compression ignition engines and more attention is focused in India because of its potential to generate large-scale employment and relatively low environmental degradation. The present investigation was to study the effect of cooled exhaust gas recirculation (EGR) on four stroke, single cylinder, direct injection (DI) diesel engine using 100% waste plastic oil. Experimental results showed higher oxides of nitrogen emissions when fueled with waste plastic oil without EGR. NO_x emissions were reduced when the engine was operated with cooled EGR. The EGR level was optimized as 20% based on significant reduction in NO_x emissions, minimum possible smoke, CO, HC emissions and comparable brake thermal efficiency. Smoke emissions of waste plastic oil were higher at all loads. Combustion parameters were found to be comparable with and without EGR. Compression ignition engines run on waste plastic oil are found to emit higher oxides of nitrogen.     

Experimental investigation on the combustion and exhaust emission characteristics of biogas-biodiesel dual-fuel combustion in a CI engine

An experimental investigation was performed to study the influence of dual-fuel combustion characteristics on the exhaust emissions and combustion performance in a diesel engine fueled with biogas-biodiesel dual-fuel. In this work, the combustion pressure and the rate of heat release were evaluated under various conditions in order to analyze the combustion and emission characteristics for single-fuel (diesel and biodiesel) and dual-fuel (biogas-diesel and biogas-biodiesel) combustion modes in a diesel engine. In addition, to compare the engine performances and exhaust emission characteristics with combustion mode, fuel consumption, exhaust gas temperature, efficiency, and exhaust emissions were also investigated under various test conditions. For the dual-fuel system, the intake system of the test engine was modified to convert into biogas and biodiesel of a dual-fueled combustion engine. Biogas was injected during the intake process by two electronically controlled gas injectors, which were installed in the intake pipe.The results of this study showed that the combustion characteristics of single-fuel combustion for biodiesel and diesel indicated the similar patterns at various engine loads. In dual-fuel mode, the peak pressure and heat release for biogas-biodiesel were slightly lower compared to biogas-diesel at low load. At 60% load, biogas-biodiesel combustion exhibited the slightly higher peak pressure, rate of heat release (ROHR) and indicated mean effective pressure (IMEP) than those of diesel. Also, the ignition delay for biogas-biodiesel indicated shortened trends compared to ULSD dual-fueling due to the higher cetane number (CN) of biodiesel. Significantly lower NO_x emissions were emitted under dual-fuel operation for both cases of pilot fuels compared to single-fuel mode at all engine load conditions. Also, biogas-biodiesel provided superior performance in reductions of soot emissions due to the absence of aromatics, the low sulfur, and oxygen contents for biodiesel.     

Biodiesel development from high acid value polanga seed oil and performance evaluation in a CI engine

Non-edible filtered high viscous (72 cSt at 40 °C) and high acid value (44 mg KOH/gm) polanga (Calophyllum inophyllum L.) oil based mono esters (biodiesel) produced by triple stage transesterification process and blended with high speed diesel (HSD) were tested for their use as a substitute fuel of diesel in a single cylinder diesel engine. HSD and polanga oil methyl ester (POME) fuel blends (20%, 40%, 60%, 80%, and 100%) were used for conducting the short-term engine performance tests at varying loads (0%, 20%, 40%, 60%, 80%, and 100%). Tests were carried out over entire range of engine operation at varying conditions of speed and load. The brake specific fuel consumption (BSFC) and brake thermal efficiency (BTE) were calculated from the recorded data. The engine performance parameters such as fuel consumption, thermal efficiency, exhaust gas temperature and exhaust emissions (CO, CO₂, HC, NO_x, and O₂) were recorded. The optimum engine operating condition based on lower brake specific fuel consumption and higher brake thermal efficiency was observed at 100% load for neat biodiesel. From emission point of view the neat POME was found to be the best fuel as it showed lesser exhaust emission as compared to HSD.     

Experimental study on diesel engine nitrogen oxide reduction running with jojoba methyl ester by exhaust gas recirculation

Jojoba methyl ester (JME) has been used as a renewable fuel in numerous studies evaluating its potential use in diesel engines. These studies showed that this fuel is a very good gas oil substitute but an increase in the nitrogenous oxides emissions was observed at all operating conditions. The aim of this study mainly was to quantify the efficiency of exhaust gas recirculation (EGR) when using JME fuel in a fully instrumented, two-cylinder, naturally aspirated, four-stroke direct injection diesel engine. The tests were made in two sections. Firstly, the measured performance and exhaust emissions of the diesel engine operating with diesel fuel and JME are determined and compared. Secondly, tests were performed at two speeds and loads to investigate the EGR effect on engine performance and exhaust emissions including nitrogenous oxides (NO_x), carbon monoxide (CO), unburned hydrocarbons (HC) and exhaust gas temperatures. Also, effect of cooled EGR with high ratio at full load on engine performance and emissions was examined. The results showed that EGR is an effective technique for reducing NO_x emissions with JME fuel especially in light duty diesel engines. A better trade-off between HC, CO and NO_x emissions can be attained within a limited EGR rate of 5-15% with very little economy penalty.     

Methyl and ethyl soybean esters as renewable fuels for diesel engines

The primary problems associated with using straight soybean oil as a fuel in a compression ignition internal combustion engine are caused by high fuel viscosity. Transesterification of soybean oil with an alcohol provides a significant reduction in viscosity, thereby enhancing the physical properties of the renewable fuel to improve engine performance. The ethyl and methyl esters of soybean oil with commercial diesel fuel additives revealed fuel properties that compared very well with diesel fuel, with the exception of gum formation, which manifested itself in problems with the plugging of fuel filters. Engine performance using soybean ester fuels differed little from engine performance with diesel fuel. A slight power loss combined with an increase in fuel consumption were experienced with the esters, primarily because of the lower heating value of the esters than for diesel fuel. Emissions for the 2 fuels were similar, with nitrous oxide emissions higher for the esters. Measurements of engine wear and fuel-injection system tests showed no abnormal characteristics for any of the fuels after the 200-hr tests. Engine deposits were comparable in amount, but slightly different in color and texture, with the methyl ester engine experiencing greater carbon and varnish deposits on the pistons. Presented at the American Oil Chemists’ Society meeting, Chicago, May 1983.     

Attempts to reduce NOx exhaust emissions by using reformulated biodiesel

Biodiesel is a renewable, domestically produced fuel that has been shown to reduce particulate, hydrocarbon, and carbon monoxide emissions from diesel engines. Under some conditions, however, biodiesel produced from certain feedstocks has been shown to cause an increase in nitrogen oxides (NO_x). This is of special concern in urban areas that are subject to strict environmental regulations. Although soy-based biodiesel may increase the emission of nitrogen oxides, it is the most easily accessible in North America. We investigated two routes to reformulate soy-based biodiesel in an effort to reduce nitrogen oxide emissions. In one of these, soy-oil methyl esters were modified by conversion of a proportion of the cis bonds in the fatty acid chains of its methyl esters to their trans isomers. In the other approach, polyol derivatives of soybean oil were transesterified to form soy methyl polyol fatty acid esters. The NO_x emissions of these modified biodiesels were then examined, using a Yanmar L100 single cylinder, four stroke, naturally aspirated, air cooled, direct injection diesel engine. Using either isomerized methyl oleate or isomerized soy biodiesel, at 20% blend level in petroleum diesel (‘B20’), nitrogen oxide emissions were elevated by between 1.5 and 3 percentage points relative to the combustion of a B20 blend of commercial biodiesel. Nitrogen oxide emissions were reduced in proportion to blend level during the combustion of polyol biodiesel, with a 20% blend in petrodiesel resulting in a reduction of about 4.5 percentage points relative to the emissions of a comparable blend of commercial soy biodiesel.