Modified CaO-based sorbent looping cycle for CO2 mitigation

CaO-based sorbent looping cycle, i.e. cyclic calcination/carbonation, is one of the most interesting technologies for CO₂ capture during coal combustion and gasification processes. In order to improve the durability of limestone during the multiple calcination/carbonation cycles, modified limestone with acetic acid solution was proposed as an CO₂ sorbent. The cyclic carbonation conversions of modified limestone and original one were investigated in a twin fixed bed reactor system. The modified limestone shows the optimum carbonation conversion at the carbonation temperature of 650 °C and achieves a conversion of 0.5 after 20 cycles. The original limestone exhibits the maximum carbonation conversion of 0.15 after 20 cycles. Conversion of the modified limestone decreases slightly as the calcination temperature increases from 920 °C to 1100 °C with the number of cycles, while conversion of the original one displays a sharp decay at the same reaction conditions. The durability of the modified limestone is significantly better than the original one during the multiple cycles because mean grain size of CaO derived from the modified limestone is lower than that from the original one at the same reaction conditions. The calcined modified limestone shows higher surface area and pore volume than the calcined original one with the number of cycles, and pore size distribution of the modified limestone is superior to the original one after the same number of calcinations.     

Cyclic CO2 capture behavior of KMnO4-doped CaO-based sorbent

This study examines the CO₂ capture behavior of KMnO₄-doped CaO-based sorbent during the multiple calcination/carbonation cycles. The cyclic carbonation behavior of CaCO₃ doped with KMnO₄ and the untreated CaCO₃ was investigated. The addition of KMnO₄ improves the cyclic carbonation rate of the sorbent above carbonation time of 257 s at each carbonation cycle. When the mass ratio of KMnO₄/CaCO₃ is about 0.5-0.8 wt.%, the sorbent can achieve an optimum carbonation conversion during the long-term cycles. The carbonation temperature of 660-710 °C is beneficial to cyclic carbonation of KMnO₄-doped CaCO₃. The addition of KMnO₄ improves the long-term performance of CaCO₃, resulting in directly measured conversion as high as 0.35 after 100 cycles, while the untreated CaCO₃ retains conversion less than 0.16 at the same reaction conditions. The addition of KMnO₄ decreases the surface area and pore volume of CaCO₃ after 1 cycle, but it maintains the surface area and pores between 26 nm and 175 nm of the sorbent during the multiple cycles. Calculation reveals that the addition of KMnO₄ improves the CO₂ capture efficiency significantly using a CaCO₃ calcination/carbonation cycle and decreases the amount of the fresh sorbent.     

Ca-based sorbent looping combustion for CO2 capture in pilot-scale dual fluidized beds

To demonstrate process feasibility of in situ CO₂ capture from combustion of fossil fuels using Ca-based sorbent looping technology, a flexible atmospheric dual fluidized bed combustion system has been constructed. Both reactors have an ID of 100 mm and can be operated at up to 1000 °C at atmospheric pressure. This paper presents preliminary results for a variety of operating conditions, including sorbent looping rate, flue gas stream volume, CaO/CO₂ ratio and combustion mode for supplying heat to the sorbent regenerator, including oxy-fuel combustion of biomass and coal with flue gas recirculation to achieve high-concentration CO₂ in the off-gas. It is the authors' belief that this study is the first demonstration of this technology using a pilot-scale dual fluidized bed system, with continuous sorbent looping for in situ CO₂ capture, albeit at atmospheric pressure. A multi-cycle test was conducted and a high CO₂ capture efficiency (> 90%) was achieved for the first several cycles, which decreased to a still acceptable level (> 75%) even after more than 25 cycles. The cyclic sorbent was sampled on-line and showed general agreement with the features observed using a lab-scale thermogravimetric analysis (TGA) apparatus. CO₂ capture efficiency decreased with increasing number of sorbent looping cycles as expected, and sorbent attrition was found to be another significant factor to be limiting sorbent performance.     

Simulation and thermodynamic analysis of chemical looping reforming and CO2 enhanced chemical looping reforming

The production of hydrogen from methane via two chemical looping reforming (CLR) processes was simulated and thermodynamically analysed, one process being the conventional CLR process, the other being a CO₂ sorption enhanced process. The aim of the work was to identify suitable operating conditions for obtaining an optimum hydrogen gas purity and yield, whilst operating auto-thermally, at atmospheric pressure and with no carbon formation. In both simulations, the reactors were simulated using the Gibbs minimisation technique. NiO was used as the oxygen storing species, whilst CaO was used as the CO₂ adsorbent.     

Cyclic calcination/carbonation looping of dolomite modified with acetic acid for CO2 capture

The dolomite modified with acetic acid solution was proposed as a CO₂ sorbent for calcination/carbonation cycles. The carbonation conversions for modified and original dolomites in a twin fixed-bed reactor system with increasing the numbers of cycles were investigated. The carbonation temperature in the range of 630 °C–700 °C is beneficial to the carbonation reaction of modified dolomite. The carbonation conversion for modified dolomite is significantly higher than that for original sorbent at the same reaction conditions with increasing numbers of reaction cycles. The modified dolomite exhibits a carbonation conversion of 0.6 after 20 cycles, while the unmodified sorbent shows a conversion of 0.26 at the same reaction conditions, which is calcined at 920 °C and carbonated at 650 °C. At the high calcination temperature over 920 °C modified dolomite can maintain much higher conversion than unmodified sorbent. The mean grain size of CaO derived from modified dolomite is smaller than that from original sorbent with increasing numbers of reaction cycles. The calcined modified dolomite possesses greater surface area and pore volume than calcined original sorbent during the multiple cycles. The pore volume and pore area distributions for calcined modified dolomite are also superior to those for calcined unmodified sorbent during the looping cycle. The modified dolomite is proved as a new and promising type of regenerable CO₂ sorbent for industrial applications.     

Experimental study on CO2 capture conditions of a fluidized bed limestone decomposition reactor

In this study, the decomposition conditions of limestone particles (0.25-0.50 mm) for CO₂ capture in a steam dilution atmosphere (20-100% steam in CO₂) were investigated by using a continuously operating fluidized bed reactor. The results show that the decomposition conversion of limestone increased with the steam dilution percentage in the CO₂ supply gas. At a bed temperature of 920 °C, the conversions were 72% without steam dilution and 98% with 60% steam dilution. The conversion was 99% with 100% steam dilution at 850 °C of the bed temperature. Steam dilution can decrease not only the decomposition temperature of limestone, but also the residence time required for nearly complete decomposition of CaCO₃. The hydration and carbonation reactivities of the CaO produced were also tested and the results show that both the reactivities increased with the steam dilution percentage for decomposing limestone.     

Effect of rice husk ash addition on CO2 capture behavior of calcium-based sorbent during calcium looping cycle

Rice husk ash/CaO was proposed as a CO₂ sorbent which was prepared by rice husk ash and CaO hydration together. The CO₂ capture behavior of rice husk ash/CaO sorbent was investigated in a twin fixed bed reactor system, and its apparent morphology, pore structure characteristics and phase variation during cyclic carbonation/calcination reactions were examined by SEM-EDX, N₂ adsorption and XRD, respectively. The optimum preparation conditions for rice husk ash/CaO sorbent are hydration temperature of 75 °C, hydration time of 8 h, and mole ratio of SiO₂ in rice husk ash to CaO of 1.0. The cyclic carbonation performances of rice husk ash/CaO at these preparation conditions were compared with those of hydrated CaO and original CaO. The temperature at 660 °C–710 °C is beneficial to CO₂ absorption of rice husk ash/CaO, and it exhibits higher carbonation conversions than hydrated CaO and original CaO during multiple cycles at the same reaction conditions. Rice husk ash/CaO possesses better anti-sintering behavior than the other sorbents. Rice husk ash exhibits better effect on improving cyclic carbonation conversion of CaO than pure SiO₂ and diatomite. Rice husk ash/CaO maintains higher surface area and more abundant pores after calcination during the multiple cycles; however, the other sorbents show a sharp decay at the same reaction conditions. Ca₂SiO₄ found by XRD detection after calcination of rice husk ash/CaO is possibly a key factor in determining the cyclic CO₂ capture behavior of rice husk ash/CaO.     

The calcium looping cycle for CO2 capture from power generation, cement manufacture and hydrogen production

Calcium looping is a CO₂ capture scheme using solid CaO-based sorbents to remove CO₂ from flue gases, e.g., from a power plant, producing a concentrated stream of CO₂ (∼95%) suitable for storage. The scheme exploits the reversible gas-solid reaction between CO₂ and CaO(s) to form CaCO₃(s). Calcium looping has a number of advantages compared to closer-to-market capture schemes, including: the use of circulating fluidised bed reactors—a mature technology at large scale; sorbent derived from cheap, abundant and environmentally benign limestone and dolomite precursors; and the relatively small efficiency penalty that it imposes on the power/industrial process (i.e., estimated at 6-8 percentage points, compared to 9.5-12.5 from amine-based post-combustion capture). A further advantage is the synergy with cement manufacture, which potentially allows for decarbonisation of both cement manufacture and power production. In addition, a number of advanced applications offer the potential for significant cost reductions in the production of hydrogen from fossil fuels coupled with CO₂ capture. The range of applications of calcium looping are discussed here, including the progress made towards demonstrating this technology as a viable post-combustion capture technology using small-pilot scale rigs, and the early progress towards a 2 MW scale demonstrator.     

Characterization of calcium oxide derived from waste eggshell and its application as CO2 sorbent

The carbonation-calcination looping cycle of calcium-based sorbents is considered as an attractive method for CO₂ capture from combustion gases because it can reduce the cost during the capture steps compared to conventional technologies, e.g., solvent scrubbing. In this study, waste eggshell was used as raw material for calcium oxide-based sorbent production. The commercially available calcium carbonate was employed for comparison purpose. Calcination behavior, crystal type and crystallinity, surface chemistry, qualitative and quantitative elemental information, specific surface area and pore size, morphology of the waste eggshell and the calcined waste eggshell were characterized by thermal gravimetric analysis (TGA), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), X-ray fluorescence (XRF), N₂ sorption analysis and scanning electron microscopy (SEM), respectively. The carbonation-calcination cycles were carried out using a TGA unit with high purity CO₂ (99.999%). It was found that the carbonation conversion of the calcined eggshell was higher than that of the calcined commercially available calcium carbonate after several cycles at the same reaction conditions. This could be due to the fact that the calcined eggshell exhibited smaller particle size and appeared more macropore volume than the calcined commercially available calcium carbonate. As results, the calcined eggshell provided a higher exposed surface for the surface reaction of CO₂.     

CO2 capture capacity of CaO in long series of pressure swing sorption cycles

One promising method for the capture of CO₂ from point sources is through the usage of a lime-based sorbent. Lime (CaO) acts as a CO₂ carrier, absorbing CO₂ from the flue gas (carbonation) and releasing it in a separate reactor (calcination) to create a pure stream of CO₂ suitable for sequestration. One of the challenges with this process is the decay in calcium utilization (CO₂ capture capacity) during carbonation/calcination cycling. The reduction in calcium utilization of natural limestone over large numbers of cycles (>250) was studied. Cycling was accomplished using pressure swing CO₂ adsorption in a pressurized thermogravimetric reactor (PTGA). The effect of carbonation pressure on calcium utilization was studied in CO₂ with the reactor operated at 1000 °C. The pressure was cycled between atmospheric pressure for calcination, and 6, 11 or 21 bar for carbonation. Over the first 250 cycles, the calcium utilization reached a near-asymptotic value of 12.5-27.7%, depending on the cycling conditions. Pressure cycling resulted in improved long-term calcium utilization compared to temperature swing or CO₂ partial pressure swing adsorption under similar conditions. An increased rate of de-pressurization caused an increase in calcium utilization, attributed to fracturing of the sorbent particle during the rapid calcination, as observed via SEM analysis.     

Economical assessment of competitive enhanced limestones for CO2 capture cycles in power plants

CO₂ capture systems based on the carbonation/calcination loop have gained rapid interest due to promising carbonator CO₂ capture efficiency, low sorbent cost and no flue gases treatment is required before entering the system. These features together result in a competitively low cost CO₂ capture system. Among the key variables that influence the performance of these systems and their integration with power plants, the carbonation conversion of the sorbent and the heat requirement at calciner are the most relevant. Both variables are mainly influenced by CaO/CO₂ ratio and make-up flow of solids. New sorbents are under development to reduce the decay of their carbonation conversion with cycles. The aim of this study is to assess the competitiveness of new limestones with enhanced sorption behaviour applied to carbonation/calcination cycle integrated with a power plant, compared to raw limestone. The existence of an upper limit for the maximum average capture capacity of CaO has been considered. Above this limit, improving sorbent capture capacity does not lead to the corresponding increase in capture efficiency and, thus, reduction of CO₂ avoided cost is not observed. Simulations calculate the maximum price for enhanced sorbents to achieve a reduction in CO₂ removal cost under different process conditions (solid circulation and make-up flow). The present study may be used as an assessment tool of new sorbents to understand what prices would be competitive compare with raw limestone in the CO₂ looping capture systems.     

Enhancement of reactivity in surfactant-modified sorbent for CO2 capture in pressurized carbonation

The calcination/carbonation loop of calcium-based (Ca-based) sorbents is considered as a viable technique for CO₂ capture from combustion gases. Recent attempts to improve the CO₂ uptake of Ca-based sorbents by adding calcium lignosulfonate (CLS) with hydration have succeeded in enhancing its effectiveness. The optimum mass ratio of CLS/CaO is 0.5 wt.%. The reduction in particle size and grain size of CaO appeared to be parts of the reasons for increase in CO₂ capture. The primary cause of increase in reactivity of the modified sorbents was the ability of the CLS to retard the sintering rate and thus to remain surface area and pore volume for reaction. The CO₂ uptake of the modified sorbents was also enhanced by elevating the carbonation pressure. Experimental results indicate that the optimal reaction condition of the modified sorbents is at 0.5 MPa and 700 °C and a high conversion of 0.7 is achieved after 10 cycles, by 30% higher than that of original limestone, at the same condition.     

Sorbent attrition in a carbonation/calcination pilot plant for capturing CO2 from flue gases

There is increasing interest in CO₂ looping cycles that involve the repeated calcination and carbonation of the sorbent as a way to capture CO₂ from flue gases during the carbonation step and the generation of a pure stream of CO₂ in the oxyfired calcination step. In particular, attrition of the material in these interconnected fluidized bed reactors is a problem of general concern. Attrition of limestone derived materials has been studied in fluidized bed systems by numerous authors. In this work, we have investigated the attrition of two limestones used in a system of two interconnected circulating fluidized bed reactors operating in continuous mode as carbonation and calciner reactors. We observed a rapid initial attrition of both limestones during the calcination step which was then followed by a highly stable period (up to 140 h of added circulation for one of the limestones) during which particle size changes were negligible. This is consistent with previous observations of attrition in other systems that employ these materials. However, a comparison of the attrition model constants with the data reported in the literature showed the two limestones to be particularly fragile during the initial calcination and the first few hours of circulation. Thus, a careful choice of limestone based on its attrition properties must be taken into account in designing future carbonate looping systems.     

Thermodynamic performance of O2/CO2 gas turbine cycle with chemical recuperation by CO2-reforming of methane

This paper proposes a novel power cycle system composed of chemical recuperative cycle with CO₂–NG (natural gas) reforming and an ammonia absorption refrigeration cycle. In which, the heat is recovered from the turbine exhaust to drive CO₂–NG reformer firstly, and then lower temperature heat from the turbine exhaust is provided with the ammonia absorption refrigeration system to generate chilled media, which is used to cool the turbine inlet gas except export. In this paper, a detailed thermodynamic analysis is carried out to reveal the performance of the proposed cycle and the influence of key parameters on performance is discussed. Based on 1 kg s⁻¹ of methane feedstock and the turbine inlet temperature of 1573 K, the simulation results shown that the optimized net power generation efficiency of the cycle rises up to 49.6% on the low-heating value and the exergy efficiency 47.9%, the new cycle system reached the net electric-power production 24.799 MW, the export chilled load 0.609 MW and 2.743 kg s⁻¹ liquid CO₂ was captured, achieved the goal of CO₂ and NO_x zero-emission.     

Partial O2-fired coal power plant with post-combustion CO2 capture: A retrofitting option for CO2 capture ready plants

In the work presented in this paper, an alternative process concept that can be applied as retrofitting option in coal-fired power plants for CO₂ capture is examined. The proposed concept is based on the combination of two fundamental CO₂ capture technologies, the partial oxyfuel mode in the furnace and the post-combustion solvent scrubbing. A 330 MW_el Greek lignite-fired power plant and a typical 600 MW_el hard coal plant have been examined for the process simulations. In a retrofit application of the ECO-Scrub technology, the existing power plant modifications are dominated by techno-economic restrictions regarding the boiler and the steam turbine islands. Heat integration from processes (air separation, CO₂ compression and purification and the flue gas treatment) can result in reduced energy and efficiency penalties. In the context of this work, heat integration options are illustrated and main results from thermodynamic simulations dealing with the most important features of the power plant with CO₂ capture are presented for both reference and retrofit case, providing a comparative view on the power plant net efficiency and energy consumptions for CO₂ capture. The operational characteristics as well as the main figures and diagrams of the plant’s heat balances are included.     

Reactivity of CaO derived from nano-sized CaCO3 particles through multiple CO2 capture-and-release cycles

The carbonation characteristics of pure CaO derived from nano-sized CaCO₃ were investigated as part of a multi-cycle performance study which showed potential for exploiting the properties of nano-sized CaO sorbents in a continuous CO₂ capture-and-release process. To help understand the approach to the decay asymptote, which is established through multiple capture-and-release cycles, a qualitative model was proposed. The rate of approach and residual conversion defined by the decay asymptote represents the establishment of an equilibrium between the pore volume and surface area loss during thermal sintering; and the pore volume and surface area regeneration as a consequence of a solid-state diffusion mechanism, and the subsequent release of CO₂ in the next calcination cycle. This qualitative explanation is valid for all CaO derived CO₂ sorbents.     

Calcination and sintering characteristics of limestone under O2/CO2 combustion atmosphere

The O₂/CO₂ coal combustion technology is an innovative combustion technology that can control CO₂, SO₂ and NO_x emissions simultaneously. Calcination and sintering characteristics of limestone under O₂/CO₂ atmosphere were investigated in this paper. The pore size, the specific pore volume and the specific surface area of CaO calcined were measured by N₂ adsorption method. The grain size of CaO calcined was determined by XRD analysis. The specific pore volume and the specific surface area of CaO calcined in O₂/CO₂ atmosphere are less than that of CaO calcined in air at the same temperature. And the pore diameter of CaO calcined in O₂/CO₂ atmosphere is larger than that in air. The specific pore volume and the specific surface area of CaO calcined in O₂/CO₂ atmosphere increase initially with temperature, and then decline as temperature exceeds 1000 °C. The peaks of the specific pore volume and the specific surface area appear at 1000 °C. The specific surface area decreases with increase in the grain size of CaO calcined. The correlations of the grain size with the specific surface area and the specific pore volume can be expressed as L = 744.67 + 464.64 lg(1 / S) and L = − 608.5 + 1342.42 lg(1 / ε), respectively. Sintering has influence on the pore structure of CaO calcined by means of influencing the grain size of CaO.     

Preparation of a highly microporous carbon from a carpet material and its application as CO2 sorbent

In order to increase the use of carpet wastes (pre- and/or post-consumer wastes), this work studies for the first time the preparation and characterisation of a microporous material from a commercial carpet (pile fiber content: 80% wool/20% nylon; primary and secondary backings: woven polypropylene; binder: polyethylene) and its application for CO₂ capture. The porous material was prepared from an entire carpet material using a standard chemical activation with KOH and then, characterised in terms of their porous structure and surface functional groups. Adsorption of CO₂ was studied using a thermogravimetric analyser at several temperatures (25-100 °C) and under different CO₂ partial pressures (i.e. pure CO₂ flow and a ternary mixture of 15% CO₂, 5% O₂ and 80% N₂). In order to examine the adsorbent regenerability, multiple CO₂ adsorption/desorption cycles were also carried out. The surface area and micropore volume of the porous adsorbent were found to be 1910.17 m² g^− 1 and 0.85 cm³ g^− 1, respectively. The CO₂ adsorption profiles illustrate that the maximum CO₂ capture on the sample was reached in less than 10 min. CO₂ adsorption capacities up to 8.41 wt.% and 3.37 wt.% were achieved at 25 and 70 °C, respectively. Thermal swing regeneration studies showed that the prepared adsorbent has good cyclic regeneration capacities.     

Integrating desulfurization with CO2-capture in chemical-looping combustion

Chemical looping combustion (CLC) is an emerging technology for clean combustion. We have previously demonstrated that the embedding of metal nanoparticles into a nanostructured ceramic matrix can result in unusually active and sinter-resistant nanocomposite oxygen carrier materials for CLC which maintain high reactivity and high-temperature stability even when sulfur contaminated fuels are used in CLC. Here, we propose a novel process scheme for in situ desulfurization of syngas with simultaneous CO₂-capture in chemical looping combustion by using these robust nanocomposite oxygen carriers simultaneously as sulfur-capture materials. We found that a nanocomposite Cu-BHA carrier can indeed strongly reduce the H₂S concentration in the fuel reactor effluent. However, during the process the support matrix is also sulfidized and takes part in the redox process of CLC. This results in SO₂ production during the reduction of the oxygen carrier and thus limits the degree of desulfurization attainable with this kind of carrier. Nevertheless, the results suggest that simultaneous desulfurization and CO₂ capture in CLC is feasible with Cu as oxygen carrier as long as appropriate carrier support materials are chosen, and could result in a novel, strongly intensified process for low-emission, high efficiency combustion of sulfur contaminated fuel streams.     

Techno-economic evaluation of a PVAm CO2-selective membrane in an IGCC power plant with CO2 capture

Published data for an operating power plant, the ELCOGAS 315 MWe Puertollano plant, has been used as a basis for the simulation of an integrated gasification combined cycle process with CO₂ capture. This incorporated a fixed site carrier polyvinylamine membrane to separate the CO₂ from a CO-shifted syngas stream. It appears that the modified process, using a sour shift catalyst prior to sulphur removal, could achieve greater than 85% CO₂ recovery at 95 vol% purity. The efficiency penalty for such a process would be approximately 10% points, including CO₂ compression. A modified plant with CO₂ capture and compression was calculated to cost €2320/kW, producing electricity at a cost of 7.6 € cents/kWh and a CO₂ avoidance cost of about €40/tonne CO₂.