Effect of antioxidants on the oxidative stability of methyl soyate (biodiesel)

Biodiesel, an alternative diesel fuel derived from transesterification of vegetable oils or animal fats, is composed of saturated and unsaturated long-chain fatty acid alkyl esters. When exposed to air during storage, autoxidation of biodiesel can cause degradation of fuel quality by adversely affecting properties such as kinematic viscosity, acid value and peroxide value. One approach for increasing resistance of fatty derivatives against autoxidation is to treat them with oxidation inhibitors (antioxidants). This study examines the effectiveness of five such antioxidants, tert-butylhydroquinone (TBHQ), butylated hydroxyanisole (BHA), butylated hydroxytoluene (BHT), propyl gallate (PrG) and α-Tocopherol in mixtures with soybean oil fatty acid methyl esters (SME). Antioxidant activity in terms of increasing oxidation onset temperature (OT) was determined by non-isothermal pressurized-differential scanning calorimetry (P-DSC). Analyses were conducted in static (zero gas flow) and dynamic (positive gas flow) mode under 2000 kPa (290 psig) pressure and 5 °C/min heating scan rate. Results showed that PrG, BHT and BHA were most effective and α-Tocopherol least effective in increasing OT. Increasing antioxidant loading (concentration) showed sharp increases in activity for loadings up to 1000 ppm followed by smaller increases in activity at higher loadings. Phase equilibrium studies were also conducted to test physical compatibility of antioxidants in SME-No. 2 diesel fuel (D2) blends. Overall, this study recommends BHA or TBHQ (loadings up to 3000 ppm) for safeguarding biodiesel from effects of autoxidation during storage. BHT is also suitable at relatively low loadings (210 ppm after blending). PrG showed some compatibility problems and may not be readily soluble in blends with larger SME ratios. Although α-Tocopherol showed very good compatibility in blends, it was significantly less effective than the synthetic antioxidants screened in this work.     

Effect of selected antioxidants on the stability of virgin olive oil

Virgin unrefined olive oil was protected from oxidation with the antioxidants butylated hydroxyanisole (BHA), butylated hydroxytoluene (BHT), and tertiary butylhydroquinone (TBHQ) and in one case propyl gallate (PG). All the antioxidants improved the stability of olive oil under accelerated conditions (oven test) and storage conditions at 50 C. In the oven test, where the type of oil used was the same as that used in long-term storage studies (room temperature and 50 C) the relative inhibition effect of the antioxidants was in the following order: TBHQ = BHA > BHT. The combinations of BHA and BHT with TBHQ displayed better stabilizing qualities. Antioxidants did not prevent peroxide formation in olive oil stored at room temperature in daylight; these samples oxidized to a high degree, probably due to the catalytic action of chlorophyll. Citric acid (CA) used alone did not affect the oxidative stability of the oil in the oven test and at room temperature in the dark, but exhibited a negative effect at 50 C. The reduction in peroxide content with teritary butylhydroquinone (TBHQ) in the dark at 50 C was greater than anticipated from the oven studies. Potency of the antioxidants under these conditions (50 C) was in the following order: TBHQ> BHT > BHA. The combinations of BHA 0.01% or BHT 0.01% with TBHQ 0.005% used in the dark at 50 C were less effective than TBHQ 0.01%.     

The Effect of Natural and Synthetic Antioxidants on the Oxidative Stability of Biodiesel

A significant problem associated with the commercial acceptance of biodiesel is poor oxidative stability. This study investigates the effectiveness of various natural and synthetic antioxidants [α-tocopherol (α-T), butylated hydroxyanisole (BHA), butyl-4-methylphenol (BHT), tert-butylhydroquinone (TBHQ), 2, 5-di-tert-butyl-hydroquinone (DTBHQ), ionol BF200 (IB), propylgallate (PG), and pyrogallol (PY)] to improve the oxidative stability of soybean oil (SBO-), cottonseed oil (CSO-), poultry fat (PF-), and yellow grease (YG-) based biodiesel at the varying concentrations between 250 and 1,000 ppm. Results indicate that different types of biodiesel have different natural levels of oxidative stability, indicating that natural antioxidants play a significant role in determining oxidative stability. Moreover, PG, PY, TBHQ, BHA, BHT, DTBHQ, and IB can enhance the oxidative stability for these different types of biodiesel. Antioxidant activity increased with increasing concentration. The induction period of SBO-, CSO-, YG-, and distilled SBO-based biodiesel could be improved significantly with PY, PG and TBHQ, while PY, BHA, and BHT show the best results for PF-based biodiesel. This indicates that the effect of each antioxidant on biodiesel differs depending on different feedstock. Moreover, the effect of antioxidants on B20 and B100 was similar; suggesting that improving the oxidative stability of biodiesel can effectively increase that of biodiesel blends. The oxidative stability of untreated SBO-based biodiesel decreased with the increasing indoor and outdoor storage time, while the induction period values with adding TBHQ to SBO-based biodiesel remained constant for up to 9 months.     

Canola extract as an alternative natural antioxidant for canola oil

The antioxidative activity of ethanolic extracts of canola meal at 100, 200, 500 and 1000 ppm on refined-bleached (RB) canola oil was examined and compared with commonly used synthetic antioxidants, such as butylated hydroxyanisole (BHA), butylated hydroxytoluene (BHT), BHA/BHT/monoglyceride citrate (MGC) andtert-butyl-hydroquinone (TBHQ). Stability of RB oil was monitored under Schaal oven test conditions at 65°C over a 17-d period. Progression of oxidation was monitored by weight gain, peroxide, conjugated diene, 2-thiobarbituric acid and total oxidation values. Canola extracts at 500 and 1000 ppm were more active than BHA, BHT and BHA/BHT/MGC and less effective than TBHQ at a level of 200 ppm.     

Stability of tapioca chips fried in RBD palm olein treated with antioxidants

The effectiveness of tertiarybutylhydroquinone (TBHQ), butylated hydroxyanisole (BHA) and butylated hydroxytoluene (BHT) in stabilizing tapioca chips was assessed by determining the peroxide andp-anisidine values, absorbances at 232 nm and 268 nm and the 18:2/16:0 ratios of oil extracted from tapioca chips. The order of effectiveness of the antioxidants in stabilizing the chips was found to be TBHQ > BHT > BHA. The order of effectiveness of antioxidants, TBHQ > BHT > BHA, was maintained for chips from corresponding 1st, 4th and 7th fryings. The loss of antioxidants during storage could not be directly related to oxidation parameters.     

Oxidative stability and storage behavior of fatty acid methyl esters derived from used palm oil

Fatty acid alkyl esters, especially FAME, are the most commonly used liquid biofuel. Because biofuels are expected to be important alternative renewable energy sources in the near future, more studies on their stability against oxidation need to be addressed. Biofuel derived from vegetable oils is well researched, currently with more attention focused on the reuse of waste oil sources than on pure vegetable oil for such production. A method to convert used palm oil, i.e., used frying oil, and residual oil of spent bleaching earths (SPE) to their respective methyl esters has been established by the Malaysian Palm Oil Board. These methyl esters can be used as diesel substitute. However, the methyl esters obtained from used frying oil have a low induction period (3.42 h). In Europe, any methyl esters must have an induction period of at least 6 h in Rancimat stability to be usable as biodiesel, as required by European Biodiesel Standard (EN 14214). To meet this requirement, the used frying oil methyl esters (UFOME) obtained can be treated with different types of antioxidants, either synthetic or natural, at different treatment levels, such as vitamin E, 3-ert-butyl-4-hydroxyanisole (BHA), 2,6-di-tert-butyl-4-methyl-phenol (BHT), 2,5-di-tert-butyl hydroquinone (TBHQ), and n-propyl gallate (PG), to investigate their oxidative stability and storage behavior. The order of increasing antioxidant effectiveness with respect to the oxidative stability of UFOME is: vitamin E<BHT<TBHQ<BHA<PG. Because methyl esters derived from residual oil of SBE have an induction period of 14.6 h, their treatment with antioxidants is unnecessary.     

Experimental Design Applied for Cost and Efficiency of Antioxidants in Biodiesel

Oxidation stability is a parameter of great importance for biodiesel quality control to both producers and subsequent consumers. To maintain the quality of biodiesel, currently the most effective and economical method is the addition of antioxidants that prevent or retard the biofuel oxidation reaction. In this study, efficiency and cost of synthetic antioxidants added to B100 biodiesel from soybean oil and pork fat were evaluated, using butylhydroxyanisole (BHA), butylhydroxytoluene (BHT) and tert-butylhydroquinone (TBHQ), in pure form or in mixtures, according to a simplex-centroid mixture experimental design. Results demonstrate an increased induction period (IP) in all trials when compared to the control sample, and TBHQ was the only antioxidant alone that met all the specification standards, while BHT and BHA alone met only the American standard specifications. The antioxidant mixture that presented the highest synergistic effect was that of TBHQ and BHA. Multi-response optimization indicated an optimum formulation containing 75 % TBHQ and 25 % BHA with an IP of 7.27 h at 110 °C and the antioxidant mixture cost of 31.31 USD, to be added for a ton of biodiesel. This simplex-centroid mixture experimental design shows an ability to be applied in the biodiesel, oils and fats industry to evaluate the oxidation stability and the occurrence of synergism between different mixtures of synthetic or natural antioxidants and their costs.     

A rapid method for evaluation of the oxidation stability of castor oil FAME: influence of antioxidant type and concentration

The oxidation stability of castor oil fatty methyl ester (FAME), doped with four different phenolic antioxidants, was evaluated using a rapid method of thermal and air-contact degradation. The methodology is based on the induction times observed when the samples are contacted with pure oxygen at elevated pressures and temperatures. The results indicate different performances of the antioxidants as well as synergisms between antioxidants and biodiesel. In general, the addition of antioxidants increased from 6-15 times the stability of castor oil FAME., with BHA (butylated hydroxyanisol) showing the best results for improving antioxidation in castor oil biodiesel.     

Oxidative instability of CLA concentrate and its avoidance with antioxidants

This study evaluated the effectiveness of antioxidants, such as BHA, BHT, TBHQ, propyl gallate (PG), α-tocopherol (α-1), green tea extract (GTE), and rosemary extract (RE) on oxidative stability of CLA concentrate. Stability of CLA concentrate stored in air at 45°C up to 44 d was assessed by PV. During the storage period, the PV of the control CLA concentrate sample increased from 0.20 (fresh oil) to 1654 meq/kg (oxidized oil). On the other hand, the PV for CLA concentrates treated with 200 ppm of the single synthetic antioxidants, BHA, BHT, TBHQ, and PG, increased from 0.20 to 81, 107, 78, and 101 meq/kg, respectively. Also, the PV of CLA concentrate with the addition of 200 ppm single natural antioxidants α-T, GTE, and RE lowered the final PV to 122, 140, and 110 meq/kg, respectively. Under our experimental conditions, the protective effect of 200 ppm antioxidant was in the order of TBHQ>BHA>PG>BHT>RE>α-T> GTE. These results suggest that the appropriate use of antioxidants prolongs the oxidative stability of CLA concentrate.     

Engine performance, exhaust emissions and combustion characteristics of a CI engine fuelled with croton megalocarpus methyl ester with antioxidant

The use of biodiesel as a substitute for petroleum-based diesel has become of great interest for the reasons of combating the destruction of the environment, the price of petroleum-based diesel and dependency on foreign energy sources. But for practical feasibility of biodiesel, antioxidants are added to increase the oxidation stability during long term storage. It is quite possible that these additives may affect the clean burning characteristics of biodiesel. This study investigated the experimental effects of antioxidants on the oxidation stability, engine performance, exhaust emissions and combustion characteristics of a four cylinder turbocharged direct injection (TDI) diesel engine fuelled with biodiesel from croton megalocarpus oil. The three synthetic antioxidants evaluated its effectiveness on oxidation stability of croton oil methyl ester (COME) were 1, 2, 3 tri-hydroxy benzene (Pyrogallol, PY), 3, 4, 5-tri hydroxy benzoic acid (Propyl Gallate, PG) and 2-tert butyl-4-methoxy phenol (Butylated Hydroxyanisole, BHA). The fuel sample tested in TDI diesel engine include pure croton biodiesel (B100), croton biodiesel dosed with 1000 ppm of an effective antioxidant (B100 + PY1000), B20 (20% croton biodiesel and 80% mineral diesel) and diesel fuel which was used as base fuel. The result showed that the effectiveness of the antioxidants was in the order of PY > PG > BHA. The brake specific fuel consumption (BSFC) of biodiesel fuel with antioxidants decreased more than that of biodiesel fuel without antioxidants, but both were higher than that of diesel. Antioxidants had few effects on the exhaust emissions of a diesel engine running on biodiesel. Combustion characteristics in diesel engine were not influenced by the addition of antioxidants in biodiesel fuel. This study recommends PY and PG to be used for safeguarding biodiesel fuel from the effects of autoxidation during storage. Overall, the biodiesel derived from croton megalocarpus oil can be utilized as partial substitute for mineral diesel.     

Effect of synthetic antioxidants on cholesterol stability during the thermal-induced oxidation of a polyunsaturated vegetable oil

As a molecule with an unsaturated bond, cholesterol is prone to oxidation. Cholesterol oxidation products (COP) are found in many common foods and have been shown to be atherogenic, cytotoxic, mutagenic, and possibly carcinogenic. Efforts to reduce the formation of oxidation products are considered important during the manufacture and processing of foods. The effect of synthetic antioxidants on cholesterol oxidation has not been extensively studied. We assayed the effect of five commonly used antioxidants—BHT, BHA, the n-propyl ester of 3,4,5-trihydroxy benzoic acid (PG), TBHQ, and 6-ethoxy-1,2-dihydro-2,4-trimethylquinoline (EQ)—on cholesterol stability when oxidation is induced in a Rancimat 679 instrument by bubbling air through the sample at 150°C. The sample consisted of 200 mg cholesterol dispersed in 100 g of a polyunsaturated vegetable oil (soybean oil). Formation of six COP was measured at the induction period, and at the 50 and 100 μS conductivity values. Under the experimental conditions, BHT and TBHQ were the most effective inhibitors of cholesterol oxidation. BHA and EQ were less effective, and PG was unable to prevent cholesterol oxidation. Synthetic antioxidants were more effective in preventing COP formation at the nucleus of the cholesterol structure than at the lateral chain.     

Thermal stability of some commercial synthetic antioxidants

Synthetic antioxidants are widely applied substances in human food and in animal feed industries. These products, which are mainly derived from phenolic structures, were developed to avoid or retard the oxidative rancidity of fats and oils when added either to raw material or to end-products. Synthetic antioxidants such as butylated hydroxytoluene (BHT), butylated hydroxyanisole (BHA), tertiary butylhydroxyquinone (TBHQ), and ethoxyquin (EQ) are frequently applied during the cooking of the by-products (viscera, blood, and feathers) in the poultry feed industry. However, results in terms of oxidative prevention are unequal and usually modest. Because information about the thermal stability of synthetic antioxidants is scarce, we developed a laboratory model that simulates the cooking of poultry by-products to study the effectiveness of BHT, BHA, TBHQ, and EQ. The antioxidants were thermally treated at 100–200°C, over 1 or 2 h. The effectiveness of each antioxidant after the thermal treatment was assessed with the Rancimat test by measuring the modification of the induction period for the oxidation of sardine oil and comparing it to the oxidation kinetics of the oil without added antioxidants. Within our experimental conditions, all antioxidants assayed showed different degrees of thermal instability. BHT and TBHQ were effective as antioxidants at temperatures up to 175°C, exhibiting only 25 to 30% inactivation. However, BHA and EQ were inactivated by 70 and 60%, respectively, at 150°C. Heating time (1 and 2 h) at a given temperature did not significantly modify the behavior of the antioxidants assayed. EQ is the most frequently applied antioxidant to prevent oxidative rancidity in the cooking of poultry by-products. However, according to our results, EQ and BHA, which is another antioxidant frequently used by the poultry industry, are less suitable     

Effects of natural and synthetic antioxidants on changes in refined, bleached, and deodorized palm olein during deep-fat frying of potato chips

The effects of antioxidants on the changes in quality characteristics of refined, bleached, and deodorized (RBD) palm olein during deep-fat frying (at 180°C) of potato chips for 3.5 h/d for seven consecutive days in five systems were compared in this study. The systems were RBD palm olein without antioxidant (control), with 200 ppm butylated hydroxytoluene (BHT), 200 ppm butylated hydroxyanisole (BHA), 200 ppm oleoresin rosemary, and 200 ppm sage extract. Fried oil samples were analyzed for peroxide value (PV), thiobarbituric acid (TBA) value, iodine value (IV), free fatty acid (FFA) content, polymer content, viscosity, E^1% _{1 cm} at 232 and 268 nm, color, fatty acid composition, and C_18:2/C_16:0 ratio. Sensory quality of the potato chips fried in these systems prior to storage was also evaluated. The storage stability of fried potato chips for 14 wk at ambient temperature was also determined by means of the TBA values and sensory evaluation for rancid odor. Generally, in the oil, oleoresin rosemary gave the lowest rate of increase of TBA value, polymer content, viscosity, E^1% _{1 cm} at 232 and 268 nm compared to control and three other antioxidants. The order of effectiveness (P<0.05) in inhibiting oil oxidation in RBD palm olein was oleoresin rosemary > BHA > sage extract > BHT > control. Prior to storage, the sensory evaluation of fried potato chips for each system showed that there was no significant (P>0.05) difference in terms of flavor, odor, texture, and overall acceptability. The same order of effectiveness (P<0.05) of antioxidants was observed for storage stability study of fried potato chips by TBA values. However, there was no significant (P > 0.05) difference in sensory evaluation for rancid odor during storage periods.     

The influence of antioxidants on the oxidation stability of biodiesel

Oxidation stability of bodiesel is an important issue because FA derivatives are more sensitive to oxidative degradation than mineral fuel. Therefore, in the most recent European Specifications for biodiesel, a minimum value of 6 h for the induction period at 110°C, measured with a Rancimat instrument, is specified. To guarantee this value at the filling station, the use of additional antioxidants will be necessary. In this paper we show the influence of different synthetic and natural antioxidants on the oxidation stability, using the specified test method. Biodiesel produced from rapeseed oil, sunflower oil, used frying oil, and beef tallow, both undistilled and distilled, was investigated. The four synthetic antioxidants pyrogallol (PY), propylgallate (PG), TBHQ, and BHA produced the greatest enhancement of the induction period. These four compounds and the widely used BHT were selected for further studies at concentrations from 100 to 1000 mg/kg. The induction periods of methyl esters from rapeseed, oil, used frying oil, and tallow could be improved significantly with PY, PG, and TBHQ, whereas BHT was not very effective. A good correlation was found between the improvement of the oxidation stability and the FA composition.     

The Behaviour of Phenolic Antioxidants,Synergists and their Mixtures in Two Vegetable Oils

Tertiary butylhydroquinone (TBHQ), hydroquinone (HQ), propyl gallate (PG), butylated hydroxytoluene (BHT) and butylated hydroxyanisole (BHA) had much higher antioxidant activity in crude safflower oil than in a commercial brand vegetable oil (Bint oil). The following active oxygen (AOM, hours at 97.8° C) and storage stability (days at 45° C) values for each antioxidant in safflower oil were; (27.9, 105.0), (21.2, 44.8), (15.3, 45.5), (9.8, 36.8) and (7.9, 33.5) respectively compared with (6.8, 31.5) for the control. Ascorbyl palmitate (AP), ascorbic acid (AA) and citric acid (CA) were found to improve the AOM stability of both oils. The same values in Bint oil were: (9.0, 34.3), (9.0, 28.3), (9.4, 41.0), (7.3, 28.5) and (6.2, 2.5) respectively compared with (5.3, 23.3) for the control. Ascorbyl palmitate (AP), ascorbic acid (AA) and citric acid (CA) were found to improve the AOM stability of both oils. AP was more effective and CA least effective in safflower oil, whereas the reverse was true in Bint oil. The five antioxidants were individually blended with the three synergists (0.01 % of each) and the 15 combinations added to each oil and compared with the antioxidant controls at 0.02 %. Safflower oil stability was greater with pure TBHQ, HQ and PG than with any of the synergist mixtures whereas the BHA, BHT-synergist mixtures were found equal or superior to that treated with BHA or BHT alone. Bint oil treated with CATBHQ or CA-HQ mixtures showed improved stability compared to oils treated with these antioxidants alone. However, the AOM method alone suggested CA-PG, CA-BHA and CA-BHT mixtures improved the stability compared to the oil-antioxidant controls. Chelation of metals by CA was assumed to be the primary cause of this synergism, whereas AP and AA behaved more like weak antioxidants.     

The effect of antioxidants on butter in relation to storage temperature and duration

The effects of antioxidants on the oxidative stability of butter, under different storage time and temperature conditions, were evaluated. Natural (α‐tocopherol) and synthetic (BHA and BHT) antioxidants were added to the butter samples at two concentrations (50 and 100 ppm) immediately after the butter samples were produced from the pasteurised sweet cream, after which they were kept in the dark at 4 and ?20 °C for 6 months. Peroxide value (PV) and thiobarbituric acid (TBA) number and the residual antioxidants of the samples were examined at 30‐day intervals, starting on the second day until the end of the storage period. The measurements obtained by assaying PV and TBA number in butter samples showed that both the synthetic and natural antioxidants used were capable of protecting the butter samples against oxidation during storage at both temperatures. The butter samples with 50 ppm antioxidant could be stored for more than 180 days at 4 °C without spoilage. At ?20 °C, the addition of BHA, BHT and α‐tocopherol caused a reduction in the TBA number from 0.31 (control) to 0.21, 0.23 and 0.27 mg malonaldehyde/kg butter, respectively, and the PV decreased from 0.75 (control) to 0.46, 0.56 and 0.54 meq O₂/kg butter, respectively, after 6 months of storage. The highest residue values were determined in both the 100 and 50 ppm α‐tocopherol‐containing samples. These results indicate that α‐tocopherol exhibited a very strong antioxidant activity, which was almost equal to that of the synthetic antioxidants. Therefore, the use of α‐tocopherol is recommended as a natural antioxidant to suppress the development of rancidity in butter.     

Oxidation stability of methyl esters studied by differential thermal analysis and rancimat

The oxidation stability of methyl esters derived from fresh rapeseed oil and waste frying oil, used as alternative biodiesel fuels, both distilled and undistilled, unstabilized and stabilized by pyrogallol and BHT, was studied by differential thermal analysis (DTA) under nonisothermal conditions at various heating rates and by the Rancimat test under isothermal conditions at 110°C. The results obtained by both techniques are compared. Both techniques show that oxidation stability increases considerably with the addition of antioxidants and that pyrogallol is very efficient. Distillation of the methyl esters prepared from rapeseed oil decreases their oxidation stability, obviously owing to the removal of natural antioxidants. The stability of methyl esters prepared from the waste frying oil is determined mainly by the history of the oil. From the DTA measurements, the kinetic parameters of an Arrhenius-like equation describing the temperature dependence of the oxidation induction period were obtained. The parameters enable one to assess the protective factor of antioxidants for temperatures outside the measuring region, estimate the residual stability, and model the process of biodiesel oxidation under nonisothermal conditions.     

Theoretical and Kinetic Tools for Selecting Effective Antioxidants: Application to the Protection of Omega-3 Oils with Natural and Synthetic Phenols

Radical-scavenging antioxidants play crucial roles in the protection of unsaturated oils against autoxidation and, especially, edible oils rich in omega-3 because of their high sensitivity to oxygen. Two complementary tools are employed to select, among a large set of natural and synthetic phenols, the most promising antioxidants. On the one hand, density functional theory (DFT) calculations provide bond dissociation enthalpies (BDEs) of 70 natural (i.e., tocopherols, hydroxybenzoic and cinnamic acids, flavonoids, stilbenes, lignans, and coumarins) and synthetic (i.e., 2,6-di-tert-butyl-4-methylphenol (BHT), 3-tert-butyl-4-hydroxyanisol (BHA), and tert-butylhydroquinone (TBHQ)) phenols. These BDEs are discussed on the basis of structure–activity relationships with regard to their potential antioxidant activities. On the other hand, the kinetic rate constants and number of hydrogen atoms released per phenol molecule are measured by monitoring the reaction of phenols with 2,2-diphenyl-1-picrylhydrazyl (DPPH^•) radical. The comparison of the results obtained with these two complementary methods allows highlighting the most promising antioxidants. Finally, the antioxidant effectiveness of the best candidates is assessed by following the absorption of oxygen by methyl esters of linseed oil containing 0.5 mmol L⁻¹ of antioxidant and warmed at 90 °C under oxygen atmosphere. Under these conditions, some natural phenols namely epigallocatechin gallate, myricetin, rosmarinic and carnosic acids were found to be more effective antioxidants than α-tocopherol.     

Stabilization of seal blubber and menhaden oils with green tea catechins

Catechins, namely (−)epicatechin (EC), (−)epigallocatechin (EGC), (−)epicatechin gallate (ECG) and (−)epigallocatechin gallate (EGCG), were isolated from commercial Chinese green leaves. The antioxidant activity of isolated catechins was compared with those of α-tocopherol, butylated hydroxyanisole (BHA), butylated hydroxytolene (BHT) andtert-butylhydroquinone (TBHQ), all at 200 ppm, in refined, bleached and deodorized seal blubber oil and menhaden oil. The study was carried out under Schaal oven test conditions at 65°C over a 144-h period, except for weight gain measurements, which were continued for up to 200 h. Progression of oxidation was monitored by measuring changes in weight gain and values of peroxide, conjugated diene, and 2-thiobarbituric acid-reactive substances. Oils treated with tea catechins showed excellent oxidative stability as compared with samples that contained commonly used antioxidants, such as α-tocopherol, BHA, BHT, and TBHQ. The potency of catechins in prevention of oxidation of marine oils was in the decreasing order of ECG> EGCG> EGC> EC; ECG was slightly more effective than TBHQ in systems studied.     

Zusammenhänge zwischen Fettoxidation und Antioxidantienzulagen im Mischfutter

Relations Between Fat Oxidation and Antioxidative Additives in Mixed Feeding Stuff Storage experiments with various mixtures of feeding stuffs were carried out. The influence of single factors on fat stability in test mixtures should be tested. The type of fat (refined soya bean oil, free fatty acids from soya bean oil raffination) fat content (3, 6, 9%), antioxidants (BHA, TBHQ), amount of anti oxidants (0 - 50 - 100 - 150 mg/kg feeding stuff), storage temperature (4, 14, 24°C) and storage period (6 - 12 - 24 weeks) were varied. The peroxide value (POZ) and the remaining amounts of antioxidants were used as parameters for the determination of the fat oxidation. The test results showed a some what enlarged stability of the fatty acids of soya bean oil raffination compared with refined soya bean oil in presence of anti oxidants. The stabilising effect of TBHQ was higher than that of BHA, but the consumption of antioxidants was lower with BHA than with TBHQ. With increasing amounts of antioxidants the stability of the fat was enlarged. The stability was lowered with rising storage temperature. Increasing storage period gives rise to a considerable increase in oxidation.