Stimuli response of cationic polymer brush prepared by ATRP: Application in peptide fractionation

Random cationic copolymer brushes composed of 2-(dimethylamino)ethyl methacrylate (DMAEMA) and N-isopropylacrylamide (NIPAAm) were synthesized using the atom transfer radical polymerization (ATRP) method. The effects of varying the monomer feed ratios (30:70 and 70:30 DMAEMA:NIPAAm) and polymerization times on the film height, morphology and stimuli response to pH of the brush were evaluated. While the polymerization time was found to have little influence on the properties of the brushes, the monomer feed ratios had a great impact. The 70% DMAEMA polymer brush had similar height as the 30% DMAEMA brush after 45 min; however, it had a greater response to pH and morphological change compared to the 30% DMAEMA. The 70% DMAEMA brush was used to demonstrate an efficient approach to alleviate the ion suppression effect in MALDI analysis of complex mixtures by effectively fractionating a binary mixture of peptides prior to MALDI-MS analysis.     

The role of the ratio (PEG:PPG) of a triblock copolymer (PPG‐b‐PEG‐b‐PPG) in the cure kinetics,miscibility and thermal and mechanical properties in an epoxy matrix

The aim of this study was to evaluate the role of different poly(ethylene glycol):poly(propylene glycol) (PEG:PPG) molar ratios in a triblock copolymer in the cure kinetics, miscibility and thermal and mechanical properties in an epoxy matrix. The poly(propylene glycol)‐block‐poly(ethylene glycol)‐block‐poly(propylene glycol) (PPG‐b‐PEG‐b‐PPG) triblock copolymers used had two different molecular masses: 3300 and 2000 g mol^?1. The mass concentration of PEG in the copolymer structure played a key role in the miscibility and cure kinetics of the blend as well as in the thermal–mechanical properties. Phase separation was observed only for blends formed with the 3300 g mol^?1 triblock copolymer at 20 wt%. Concerning thermal properties, the miscibility of the copolymer in the epoxy matrix reduced the T_g value by 13 °C, although a 62% increase in fracture toughness (K_IC) was observed. After the addition of PPG‐b‐PEG‐b‐PPG with 3300 g mol^?1 there was a reduction in the modulus of elasticity by 8% compared to the neat matrix; no significant changes were observed in T_g values for the immiscible system. The use of PPG‐b‐PEG‐b‐PPG with 2000 g mol^?1 reduced the modulus of elasticity by approximately 47% and increased toughness (K_IC) up to 43%. Finally, for the curing kinetics of all materials, the incorporation of the triblock copolymer PPG‐b‐PEG‐b‐PPG delayed the cure reaction of the DGEBA/DDM (DGEBA, diglycidyl ether of bisphenol A; DDM, Q3‐4,4′‐Diaminodiphenylmethane) system when there is miscibility and accelerated the cure reaction when it is immiscible. All experimental curing reactions could be fitted to the Kamal autocatalytic model presenting an excellent agreement with experimental data. This model was able to capture some interesting features of the addition of triblock copolymers in an epoxy resin. © 2018 Society of Chemical Industry     

End‐capping double‐chain stranded polypseudorotaxanes using lengthily tunable poly(2‐hydroxyethyl methacrylate) blocks via atom transfer radical polymerization

Owing to a large cavity, γ‐cyclodextrin (γ‐CD) can form double‐chain inclusion complexes with linear polymeric chains such as poly(ethylene glycol) (PEG) and poly(ε‐caprolactone). However, to date few reports have focused on the end‐capping of these kinds of fascinating supramolecular entities. In this study, atom transfer radical polymerization (ATRP) was employed to prepare double‐chain stranded polyrotaxanes (PRs) with lengthily tunable poly(2‐hydroxyethyl methacrylate) (PHEMA) blocks as bulky end‐cappers. ATRP of HEMA was carried out using pseudopolyrotaxanes (PPRs) self‐assembled from a distal 2‐bromoisobutyryl end‐capped PEG (BriB‐PEG‐iBBr) with varying amounts of γ‐CDs as macroinitiator in the presence of Cu(I)Br/N,N,N′,N″,N″‐pentamethyldiethylenetriamine in aqueous solution at room temperature. The resulting PRs were demonstrated by the unique H‐like double‐chain stranded supramolecular architecture end‐capped with lengthily tunable PHEMA blocks. When the feed molar ratio of γ‐CD:BriB‐PEG‐iBBr varied from 5 to 60 in PPRs, the feed molar ratio in PRs was found to remain at around 20 with a higher yield. ATRP was successfully applied to prepare double‐chain stranded PRs end‐capped with lengthily tunable PHEMA blocks. This provides a protocol for the preparation of novel H‐like PR‐based block copolymers. Copyright © 2010 Society of Chemical Industry     

Esterification of hydroxylated polymers with 2-sulfobenzoic acid cyclic anhydride: A facile approach for the synthesis of near-monodisperse strong acid homopolymers and diblock copolymers

A convenient two-step route was developed to prepare a range of low polydispersity strong acid homopolymers and several examples of well-defined diblock copolymers. Atom transfer radical polymerization (ATRP) of either 2-hydroxypropyl methacrylate, 2-hydroxyethyl methacrylate or glycerol monomethacrylate afforded the corresponding near-monodisperse hydroxylated homopolymers, while several diblock copolymer precursors were prepared by either (1) the one-pot ATRP of 2-hydroxypropyl methacrylate and 2-(diethylamino)ethyl methacrylate using sequential monomer addition or (2) the ATRP of either 2-hydroxypropyl methacrylate or glycerol monomethacrylate using a poly(ethylene oxide)-based macro-initiator. Excess 2-sulfobenzoic acid cyclic anhydride was used to fully esterify the hydroxy groups of these homopolymers and diblock copolymers under mild conditions. The resulting zwitterionic diblock copolymers undergo micellar self-assembly on adjusting the pH of the solution, while one of the anionic poly(ethylene oxide)-based diblock copolymers formed colloidal polyelectrolyte complexes in aqueous solution when mixed with a cationic poly(ethylene oxide)-based diblock copolymer.     

Synthesis of well‐defined comb‐like amphiphilic copolymers with protonizable units in the pendent chains: 2. Poly(2‐(dimethylamino)ethyl methacrylate) grafted poly(methyl methacrylate‐co‐2‐hydroxyethyl methacrylate) copolymers and their association behavior in aqueous solution

Narrow‐distribution, well‐defined comb‐like amphiphilic copolymers are reported in this work. The copolymers are composed of poly(methyl methacrylate‐co‐2‐hydroxyethyl methacrylate) (P(MMA‐co‐HEMA)) as the backbones and poly(2‐(dimethylamino)ethyl methacrylate) (PDMAEMA) as the grafted chains, with the copolymer backbones being synthesized via atom‐transfer radical polymerization (ATRP) and the grafted chains by oxyanionic polymerization. The copolymers were characterized by gel permeation chromatography (GPC), Fourier‐transform infrared (FT‐IR) spectroscopy and ¹H NMR spectroscopy. The aggregation behavior in aqueous solutions of the comb‐like amphiphilic copolymers was also investigated. ¹H NMR spectroscopic and surface tension measurements all indicated that the copolymers could form micelles in aqueous solutions and they possessed high surface activity. The results of dynamic light scattering (DLS) and scanning electron microscopy (SEM) investigations showed that the hydrodynamic diameters of the comb‐like amphiphilic copolymer aggregates increased with dilution. Because of the protonizable properties of the graft chains, the surface activity properties and micellar state can be easily modulated by variations in pH. Copyright © 2004 Society of Chemical Industry     

Amphiphilic copolymers based on PEG‐acrylate as surface active water viscosifiers: Towards new potential systems for enhanced oil recovery

With the purpose of investigating new potential candidates for enhanced oil recovery (EOR), amphiphilic copolymers based on Poly(ethylene glycol) methyl ether acrylate (PEGA) have been prepared by Atom Transfer Radical Polymerization (ATRP). A P(PEGA) homopolymer, a block copolymer with styrene PS‐b‐P(PEGA), and an analogous terpolymer including also sodium methacrylate (MANa) in the poly(PEGA) (PPEGA) block, PS‐b‐P(PEGA‐co‐MANa) have been prepared and characterized. Viscosity and surface activity of solutions of the prepared polymers in pure and salty water have been measured and the results have been interpreted in terms of the chemical structures of the systems. A clear influence of the presence of the charged MANa moieties has been observed in both rheological and interfacial properties. The PS‐b‐P(PEGA‐co‐MANa) terpolymer, being an effective surface active viscosifying agent, is a good candidate as polymeric surfactant for applications in enhanced oil recovery and related. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44100.     

Synthesis of well‐defined responsive membranes with fixable solvent responsiveness

A versatile method is described to synthesize a new family of solvent‐responsive membranes whose response states can be not only tunable but also fixable via ultraviolet (UV) irradiation induced crosslinking. The atom transfer radical polymerization (ATRP) initiator 2‐bromoisobutyryl bromide was first immobilized on the poly(ethylene terephthalate) (PET) track‐etched membrane followed by room‐temperature ATRP grafting of poly(2‐hydroxyethyl methacrylate) (PHEMA) and poly(2‐hydroxyethyl methacrylate‐co‐2‐(dimethylamino)ethyl methacrylate) (P(HEMA‐co‐DMAEMA)) respectively. The hydroxyl groups of PHEMA were further reacted with cinnamoyl chloride (a photosensitive monomer) to obtain photo‐crosslinkable PET‐g‐PHEMA/CA membrane and PET‐g‐P(HEMA/CA‐co‐DMAEMA) membrane. The length of grafted polymer chains was controllable by varying the polymerization time. X‐ray photoelectron spectroscopy, Fourier transform infrared spectroscopy in attenuated total reflection and thermogravimetric analysis were employed to characterize the resulting membranes. The various membrane surface morphologies resulting from different states of the grafted chains in water and dimethylformamide were characterized by scanning electron microscopy. It was demonstrated that the grafted P(HEMA/CA‐co‐DMAEMA) chains had more pronounced solvent responsivity than the grafted PHEMA/CA chains. The surface morphologies of the grafted membranes could be adjusted using different solvents and fixed by UV irradiation crosslinking. © 2014 Society of Chemical Industry     

pH‐sensitive dimethylaminoethyl methacrylate (DMAEMA)/acrylamide (AAm) hydrogels: Synthesis and adsorption from uranyl acetate solutions

A random copolymer of dimethylaminoethyl methacrylate (DMAEMA) and acrylamide(AAm) [poly(DMAEMA/AAm)], with a pH‐sensitive character, was prepared by a redox polymerization method. Increasing the DMAEMA content of the gel, the pH, and the ionic strength of the solution decreased the swelling ratios of the hydrogels. The adsorption of poly(DMAEMA/AAm) hydrogels from uranyl acetate (UA) solutions was studied at different pHs. The adsorption capacity of hydrogels increased from 200 to 1200 mg of UA per gram of dry hydrogel with increasing pH of the adsorption solution. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2028–2031, 2003     

A facile preparation of pH‐temperature dual stimuli‐responsive supramolecular hydrogel and its controllable drug release

A series of pH‐temperature dual stimuli‐responsive random copolymers poly[N,N‐dimethylaminoethyl methacrylate‐co‐poly(poly(ethylene glycol) methyl ether methacrylate][poly(DMAEMA‐co‐MPEGMA)] were synthesized by free radical polymerization. The supramolecular hydrogel was formed by pseudopolyrotaxane, which was prepared with the host‐guest interactions between α‐cyclodextrin (α‐CD) and poly(ethylene glycol) (PEG) side chains. Fourier transform infrared (FT‐IR), nuclear magnetic resonance (¹H NMR), and X‐ray diffraction (XRD) confirmed the structures of the hydrogels. The pH‐temperature dual stimuli responsive properties of the hydrogels were characterized by rheometer. Finally, the controllable drug release behavior of the hydrogel, which was used 5‐fluorouracil (5‐Fu) as the model drug, was investigated at different temperatures and different pH values. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43279.     

Synthesis and characterization of thermo‐ and pH‐sensitive block copolymers bearing a biotin group at the poly(ethylene oxide) chain end

A poly(ethylene oxide)‐block‐poly(dimethylamino ethyl methacrylate) block copolymer (PEO‐b‐PDMAEMA) bearing an amino moiety at the PEO chain end was synthesized by a one‐pot sequential oxyanionic polymerization of ethylene oxide (EO) and dimethylamino ethyl methacrylate (DMAEMA), followed by a coupling reaction between its PEO amino and a biotin derivative. The polymers were charac terized with ¹H NMR spectroscopy and gel permeation chromatography. Activated biotin, biotin‐NHS (N‐hydroxysuccinimide), was used to synthesize biotin‐PEO‐PDMAEMA. In aqueous media, the solubility of the copolymer was temperature‐ and pH‐sensitive. The particle size of the micelle formed from functionalized block copolymers was determined by dynamic light scattering. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3552–3558, 2006     

Interaction between a tertiary amine methacrylate based polyelectrolyte and a sodium montmorillonite dispersion and its rheological and colloidal properties

The rheological and colloidal properties of sodium montmorillonite dispersions were investigated in the presence of a special type of cationic polymer [modified poly(ethylene glycol)]. 2‐(Dimethylamino) ethyl methacrylate was polymerized with monomethoxy‐capped oligo(ethylene glycol) via aqueous atom transfer radical polymerization. The tertiary amine residues of the resulting polymer were then quaternized with methyl iodide to obtain a cationic polyelectrolyte. The rheology and ζ‐potential experiments showed that the cationic polymer adsorbed onto the sodium montmorillonite surface strongly. The rheological parameters (plastic viscosity and yield value) were obtained with a rotational low‐shear rheometer. The results indicated a gradual increase in gelation with the addition of the cationic polymer, which reached a maximum at a cationic polymer concentration of 0.4–0.8 g/L. This gel‐like dispersion showed pronounced thixotropy. A further increase in the polymer concentration resulted in a reduction in this gelation. The adsorption of the cationic polymer onto the clay surface reduced the ζ potential to small values, but no isoelectric point was observed. The basal‐spacing measurements showed that the cationic polymer strongly adsorbed onto the sodium montmorillonite instead of entering the montmorillonite layers. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 95: 300–306, 2005     

Preparation and application in drug controlled delivery of pH‐sensitive P(CE‐co‐DMAEMA‐co‐MEG) hydrogel

A pH‐sensitive hydrogel [P(CE‐co‐DMAEMA‐co‐MEG)] was synthesized by the free‐radical crosslinking polymerization of N,N‐dimethylaminoethyl methacrylate (DMAEMA), poly(ethylene glycol) methyl ether methacrylate(MPEG‐Mac) and methoxyl poly(ethylene glycol)‐poly(caprolactone)‐methacryloyl methchloride (PCE‐Mac). The effects of pH and monomer content on swelling property, swelling and deswelling kinetics of the hydrogels were examined and hydrogel microstructures were investigated by SEM. Sodium salicylate was chosen as a model drug and the controlled‐release properties of hydrogels were pilot studied. The results indicated that the swelling ratios of the gels in stimulated gastric fluids (SGF, pH = 1.4) were higher than those in stimulated intestinal fluids (SIF, pH = 7.4), and followed a non‐Fickian and a Fickian diffusion mechanism, respectively. In vitro release studies showed that its release rate depends on different swelling of the network as a function of the environmental pH and DMAEMA content. SEM micrographs showed homogenous pore structure of the hydrogel with open pores at pH 1.4. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40737.     

Synthesis of hydroxyl-capped comb-like poly(ethylene glycol) to develop shell cross-linkable micelles

A novel hydroxyl-capped comb-like poly[poly(ethylene glycol) methacrylate] (PPEGMA) was prepared via atom transfer radical polymerization (ATRP) of α-methylacryloyl-ω-hydroxyl-poly(ethylene glycol) at ambient temperature. The polymerization kinetics of the block copolymer was studied by gel permeation chromatography (GPC) and ¹H NMR. It is of interest to find the well-defined comb-like PEG can associate into micelles, which have hydrophilic PEG shell end-capped by hydroxyl groups. The hydroxyl in the shell were further cross-linked by divinyl sulfone (DVS), which could couple with two capped-end hydroxyl groups. The XPS, TEM, AFM and laser scattering particle size distribution analyzer results revealed that reactive micelles could be cross-linked by DVS. The reactive, cross-linkable micelles with PEG shell may have great potential as new drug carrier and nanoreactor, etc.     

Synthesis and thermal properties of poly(methyl methacrylate)‐poly(L‐lactic acid)‐poly(methyl methacrylate) tri‐block copolymer

Poly(methyl methacrylate)‐poly(L ‐lactic acid)‐poly(methyl methacrylate) tri‐block copolymer was prepared using atom transfer radical polymerization (ATRP). The structure and properties of the copolymer were analyzed using infrared spectroscopy, gel permeation chromatography, nuclear magnetic resonance (¹H‐NMR, ¹³C‐NMR), thermogravimetry, and differential scanning calorimetry. The kinetic plot for the ATRP of methyl methacrylate using poly(L ‐lactic acid) (PLLA) as the initiator shows that the reaction time increases linearly with ln[M]₀/[M]. The results indicate that it is possible to achieve grafted chains with well‐defined molecular weights, and block copolymers with narrowed molecular weight distributions. The thermal stability of PLLA is improved by copolymerization. A new wash‐extraction method for removing copper from the ATRP has also exhibits satisfactory results. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Alkali‐responsive membrane prepared by grafting dimethylaminoethyl methacrylate onto ethylene vinyl alcohol copolymer membrane

An alkali‐responsive membrane was prepared by grafting dimethylaminoethyl methacrylate (DMAEMA) onto ethylene vinyl alcohol copolymer (EVAL) membrane using ultraviolet (UV) irradiation graft polymerization. A subtranslucent state of EVAL membrane swelling in the DMAEMA solution was observed, and such a state enabled the passage of UV light through all the pores, inducing graft polymerization inside the pores and on the back. Attenuated total reflectance Fourier‐transform infrared spectrometer (ATR‐FTIR), X‐ray photoelectron spectroscopy (XPS), field‐emission scanning electron microscopy (FESEM), and energy‐dispersive X‐ray spectroscope (EDX) confirmed that the poly(DMAEMA)‐grafted chains existed not only on the top surface, but also inside the pores and on the back. Atomic force microscopy (AFM) and nitrogen adsorption analysis confirmed that the grafted chains collapsed in air, and decreased the surface roughness, surface area, and pore size of the grafted membranes. Alkali‐responsive properties of the poly(DMAEMA)‐grafted EVAL membrane (i.e., contact angle, permeability, and selectivity) were observed in the pH range of 9–10. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41775.     

Use of a CO2‐switchable hydrophobic associating polymer to enhance viscosity–response

A series of copolymers, poly(acrylamide)‐co‐poly(N,N‐dimethylaminoethyl methacrylate)‐co‐poly(N‐cetyl DMAEMA) (abbreviation PDAMCn), was synthesized with different monomer ratios. The resulting copolymer solution shows pronounced viscosity–response property which is CO₂‐triggered and N₂‐enabled. Electrical conductivity experiment shows that tertiary amine group on DMAEMA experiences a protonate and deprotonate transition upon CO₂ addition and its removal. In addition, different incorporation rates of DMAEMA leads to two kinds of morphological change in the presence of CO₂ and thus induces different rheological behaviors. PDAMCn incorporating longer hydrophobic monomer (C₁₈DM) show more pronounced initial viscosity and higher critical stress required to cause network deformation, which consequently enhances the viscosity–response property of the solution. The addition of NaCl could also tune the viscosity of PDAMCn solution. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41468.     

Formation of liquid‐crystalline morphologies in dilute solutions of a charged random terpolymer

Formation of micellar morphologies in aqueous solutions of charged random copolymers has been reported in several studies. This paper reports on liquid crystallization of the cationic random acrylic terpolymer i.e., poly[(dimethylaminoethyl methacrylate)‐co‐(methyl methacrylate)‐co‐(butyl methacrylate)] containing no mesogenic groups. The viscometric behaviour of the terpolymer solutions deviated in several ways from ordinary behaviour of polyelectrolytes supporting the possibility of self‐assembly of this cationic random terpolymer in a solvent mixture containing acetone, ethanol and 1‐propanol or each of these solvents separately. The existence of nano‐sized liquid‐crystalline structures was demonstrated using small‐angle X‐ray scattering (SAXS) analysis of the terpolymer solutions. Morphology and sizes of the liquid‐crystalline structures were determined according to the SAXS results and confirmed by dynamic light scattering and atomic force microscopy findings. Liquid crystallization was reasoned on the basis of the existence of a segregated chain microstructure as for polyelectrolytes containing folded parts connected to each other by monomer strings. In a random amphiphilic copolymer or the terpolymer under investigation, the folded parts and strings must be hydrophilic and hydrophobic, respectively. The role of alcohol aggregates should be considered in self‐assembly of the terpolymer chains. The alcohol aggregates can act as physical crosslinkers leading to the formation of more compact liquid‐crystalline structures. The deviations observed in the viscometric behaviour of the terpolymer solutions are suggested as the result of the ability of terpolymer chains to self‐assemble. © 2013 Society of Chemical Industry     

Photophysical properties and self-assembly of triblock copolymer with complexes of positively charged PDMAEMA and oppositely charged chromophores

The self-assembly and photophysical properties of a triblock copolymer with complex mid-block in THF and aqueous solution were investigated in this research. Poly(poly(ethylene glycol) methyl ether methacrylate)-block-poly(2-(dimethylamino ethyl methacrylate)-block- poly(poly(ethylene glycol) methyl ether methacrylate) (PPEGMA–b–PDMAEMA–b–PPEGMA) triblock copolymer was synthesized by subsequent atom transfer radical polymerizations (ATRP) of DMAEMA and PEGMA. The PDMAEMA blocks were quaternized by a reaction with iodomethane. The complex of the positively charged PDMAEMA chain unit and sodium salt of 1-pyrenebutyric acid was prepared by mixing equimolar amount of the two components in THF/water mixture. Transmission electron microscopy and fluorescence technique results show that the triblock copolymer chains self-assemble into micelles in THF at high concentration. The critical aggregation concentration (CAC) of the triblock copolymer in THF determined by fluorescence technique is 6.8 × 10^?5 M. The triblock copolymer was also able to self-assemble into micelles in water. The value of CAC of the triblock copolymer in water is 2.0 × 10^?5 M. The photophysical properties and self-assembly structures of the triblock copolymer in aqueous solutions were influenced by added sodium chloride. After salt addition, a transition of the assembled structures from micelles to hollow structures was observed.     

Poly(n-butyl methacrylate) end-capped polyrotaxanes via ATRP initiated with α-cyclodextrin and Pluronic 17R4 based inclusion complexes

A series of polyrotaxane (PR)-based triblock copolymers comprising a PR middle block and poly(n-butyl methacrylate) (PBMA) flanked blocks were prepared via bulk ATRP of n-butyl methacrylate initiated with polypseudorotaxanes self-assembled from α-cyclodextrins (α-CDs) with 2-bromoisobutyryl terminated Pluronic 17R4 at 35 °C. Their structure was verified by ¹H NMR, FTIR, GPC, WXRD and TGA analyses. The dethreading of entrapped α-CDs during the polymerization process was effectively impeded through an elaborated choice of Pluronic 17R4, a PPG–PEG–PPG triblock copolymer, in which α-CDs site-selectively include with the middle PEG block and are inhibited by the flanked PPG blocks. The degree of polymerization of attached PBMA blocks appeared to be tunable to some extent. The polydispersity index of the resulting PR-based triblock copolymers is in a low range of 1.28–1.50. As an attempt toward the materialization of these unique supramolecular polymers, a selected sample was dissolved in methylene dichloride and electrospun into micro-sized particles. Nevertheless, they can be not only casted into tough films but also melt extruded into sticks.     

Preparation of stealth micellar nanoparticles of novel biodegradable and biocompatible brush copolymers with cholesteryl-modified PLA and PEG side chains

Novel amphiphilic brush copolymers, P(CPLAMA)-co-P(PEGMA), of cholesteryl poly(l-lactic acid) (CPLA) and poly(ethylene glycol) monomethyl ether (PEG) with determined hydrophobic/hydrophilic ratios were synthesized by the methacrylate (MA) macromonomer copolymerization method. Brush copolymers were prepared via both free radical polymerization (FRP) and atom transfer radical polymerization (ATRP). The copolymer compositions were determined by ¹H NMR spectroscopy. The synthesized copolymers were used to prepare the micellar nanoparticles with hydrophobic CPLA and hydrophilic PEG forming the core and shell, respectively. The critical micelle concentration (CMC) values of the samples produced by FRP (brush copolymer 1) and ATRP (brush copolymer 2) were estimated to be approximately 0.9 and 0.7 mg/L in aqueous solution by a fluorescence probe technique, respectively. The transmission electron microscopy (TEM) images of micelles of the brush copolymers 1 and 2 showed that micelles were spherical in shape with a mean diameter of 111 and 32 nm, respectively. The results showed that the size of micelles became larger with the increase of the molecular weight of polymer and the relative content of the hydrophilic PEG as well. The drug loading efficiency and drug-releasing properties of the micelles were investigated by using naproxen as a hydrophobic model drug. The in vitro release of naproxen-loaded micelles with about 85–89 % loading efficiency and 17–18 % loading capacity was studied by a using dialysis method in phosphate-buffered solution at 37 °C. The drug-releasing characteristics exhibited a phase of slow release. On the basis of the results obtained, the proposed brush copolymers may be useful in various targeted drug delivery applications, especially those involving hydrophobic drugs.