Binary and ternary polymer blends containing poly(vinylidene chloride‐co‐acrylonitrile)

Poly(vinylidene chloride‐co‐acrylonitrile) (Saran F), poly(hydroxy ether of bisphenol A) (phenoxy), poly(styrene‐co‐acrylonitrile) (PSAN), and poly(vinyl phenol) (PVPh) all have the same characteristic: miscibility with atactic poly(methyl methacrylate) (aPMMA). However, the miscibility of Saran F with the other polymer (phenoxy, PSAN, or PVPh) is not guaranteed and was thus investigated. Saran F was found to be miscible only with PSAN but not miscible with phenoxy and PVPh. Because Saran F and PVPh are not miscible, although they are both miscible with aPMMA, aPMMA can thus be used as a potential cosolvent to homogenize PVPh/Saran F. The second part of this report focused on the miscibility of a ternary blend consisting of Saran F, PVPh, and aPMMA to investigate the cosolvent effect of aPMMA. Factors affecting the miscibility were studied. The established phase diagram indicated that the ternary blends with high PVPh/Saran F weight ratio were found to be mostly immiscible. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3068–3073, 2004     

The totally miscible in ternary hydrogen‐bonded polymer blend of poly(vinyl phenol)/phenoxy/phenolic

The individual binary polymer blends of phenolic/phenoxy, phenolic/poly(vinyl phenol) (PVPh), and phenoxy/PVPh have specific interaction through intermolecular hydrogen bonding of hydroxyl–hydroxyl group to form homogeneous miscible phase. In addition, the miscibility and hydrogen bonding behaviors of ternary hydrogen bond blends of phenolic/phenoxy/PVPh were investigated by using differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy, and optical microscopy. According to the DSC analysis, every composition of the ternary blend shows single glass transition temperature (T_g), indicating that this ternary hydrogen‐bonded blend is totally miscible. The interassociation equilibrium constant between each binary blend was calculated from the appropriate model compounds. The interassociation equilibrium constant (K_A) of each individually binary blend is higher than any self‐association equilibrium constant (K_B), resulting in the hydroxyl group tending to form interassociation hydrogen bond. Photographs of optical microscopy show this ternary blend possess lower critical solution temperature (LCST) phase diagram. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Influence of molecular interactions on spherulite morphology in miscible poly(ethylene oxide)/epoxy network versus poly(ethylene oxide)/poly(4‐vinyl phenol) blend

Relationships between the spherulite morphology and changes in hydrogen‐bonding interactions between the linear poly(ethylene oxide) (PEO) polymer and a crosslinking epoxy system (diglycidylether of bisphenol‐A resin with 4,4′‐diaminodiphenylsulfone) (DGEBA/DDS) before and after cure have been explored The hydrogen‐bonding interaction is more significant before cure because of the interactions between the ether group of PEO and the amine group of DDS. The interaction between PEO and epoxy/DDS becomes less in the cured network. The morphology of the PEO crystals is, in turn, affected by the contents and chemical structures (functional groups, molecular weights, crosslinks, etc) of crosslinking epoxy/DDS. PEO/poly(4‐vinyl phenol) (PVPh), a thermoplastic non‐curing miscible system with the hydrogen bonding between the ether group of PEO and the ? OH group of PVPh, is also compared. In comparison with the PEO/epoxy/DDS system, the spherulite morphology of PEO/PVPh becomes more extensively spread out, with the extents increasing with the PVPh contents in the PEO/PVPh blend. © 2001 Society of Chemical Industry     

Reexamination of the miscibility of stereoregular poly(methyl methacrylate) with poly(vinyl phenol)

Previously, isotactic, atactic, and syndiotactic poly(methyl methacrylates) (PMMAs) (designated as iPMMA, aPMMA, and sPMMA) were mixed with poly(vinyl phenol) (PVPh) separately in tetrahydrofuran (THF) to make three polymer blend systems. According to calorimetry data, iPMMA was found to be miscible with PVPh; however, partial miscibility or immiscibility was found between aPMMA (or sPMMA) and PVPh. According to the article by C. J. T. Landry and D. M. Teegarden, Macromolecules, 1991, 24, 4310, THF is the reason for causing aPMMA and PVPh to phase separate, but 2‐butanone instead produces miscible blends. Therefore, in this article these three polymer systems were investigated again using 2‐butanone as solvent. Films were prepared under specific conditions to minimize the effect of aggregation in PMMA. The formation of hydrogen bonding between PMMA and PVPh and the attendant changes in the aggregation of PMMA segments were determined in the solid states by means of FTIR. Based on the results of calorimetry, iPMMA and aPMMA were found to be miscible with PVPh. For iPMMA/PVPh blends, different degrees of hydrogen bonding were observed based on DSC data and FTIR spectra when compared to previous study. An elevation of the glass transition temperatures (T_gs) of aPMMA/PVPh blends above weight average was detected and the T_g values were fitted well by the Kwei equation. But partial miscibility was still found between sPMMA and PVPh on account of the observation of two T_gs in most compositions. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 1425–1431, 2002     

Effect of the tacticity of poly(methyl methacrylate) on the phase diagram of its ternary blends

Previously, isotactic and atactic poly(methyl methacrylates) (PMMAs) were found to be miscible with poly(vinyl phenol) (PVPh) and poly(hydroxy ether of bisphenol‐A) (phenoxy) because all the prepared films were transparent and showed composition‐dependent glass transition temperatures (T_g's). However, syndiotactic PMMA was immiscible with PVPh because most of the cast films had two T_g's. On the contrary, syndiotactic PMMA was still miscible with phenoxy. According to our preliminary results, PVPh and phenoxy are not miscible. Also to our knowledge, nobody has reported any results concerning the effect of the tacticity of PMMA on its ternary blend containing PVPh and phenoxy. The miscibility of a ternary blend consisting of PVPh, phenoxy, and tactic PMMA was thus investigated and reported in this article. Calorimetry was used as the principal tool to study miscibility. An approximate phase diagram of the ternary blends containing different tactic PMMA was established, probably for the first time, based on differential scanning calorimetry data. Immiscibility was found in most of the studied ternaries but a slight difference due to the effect of tacticity of PMMA was definitely observed. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2720–2726, 2002     

Miscibility and interpolymer complexation of poly(2-methyl-2-oxazoline) with hydroxyl-containing polymers

Poly(2-methyl-2-oxazoline) (PMOx) was found to be miscible with poly (styrene-coallyl alcohol), poly(hydroxyether of bisphenol-A), poly (2-hydroxypropyl methacrylate) and poly(p-vinylphenol) (PVPh), when cast from N,N-dimethylformamide solutions and to form interpolymer complexes with PVPh in methanol solutions. The hydrogen bonding interactions between PMOx and hydroxyl-containing polymers were studied by infrared spectroscopy and compared with the corresponding blends of poly(2-ethyl-2-oxazoline) (PEOx). Except with phenoxy, PMOx interacts more strongly with hydroxyl-containing polymers than PEOx does.     

Poly(butylene succinate)/poly(vinyl phenol) blends. Part 1. Miscibility and crystallization

Miscibility has been investigated in blends of poly(butylene succinate) (PBSU) and poly(vinyl phenol) (PVPh) by differential scanning calorimetry in this work. PBSU is miscible with PVPh as shown by the existence of single composition dependent glass transition temperature over the entire composition range. In addition, the polymer–polymer interaction parameter, obtained from the melting depression of PBSU using the Nishi–Wang equation, is composition dependent, and its value is always negative. This indicates that PBSU/PVPh blends are thermodynamically miscible in the melt. Preliminary morphology study of PBSU/PVPh blends was also studied by optical microscopy (OM). OM experiments show the spherulites of PBSU become larger with the PVPh content, indicative of a decrease in the nucleation density, and the coarseness of PBSU spherulites increases too with increasing the PVPh content in the blends.     

Achieving miscible ternary polymer blends with hydrogen bonding

Poly(vinyl phenol) (PVPh) has previously been found to be successful in making immiscible poly(methyl methacrylate) (PMMA)/poly(vinyl acetate) (PVAc) miscible. Poly(ethyl methacrylate) (PEMA) with one more methyl group than PMMA is also immiscible with PVAc. PEMA and PVAc are miscible with PVPh according to the literature. To determine whether PVPh can also cosolubilize PEMA/PVAc, PVPh samples of two different molecular weights have been mixed in this study with PEMA and PVAc to produce a ternary blend. On the basis of the calorimetry data, the ternary PEMA/PVAc/PVPh blend, regardless of the molecular weight of PVPh, has been determined to be miscible. The reason for the observed miscibility is probably that the interactions between PVAc and PVPh are similar in magnitude to those between PEMA and PVPh. A modified Kwei equation based on the binary interaction parameters proposed previously is used to describe the experimental glass‐transition temperature of the miscible ternary blend almost quantitatively well. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 643–652, 2006     

Phase behavior of binary and ternary blends of poly(styrene‐co‐methacrylic acid), poly(styrene‐co‐4‐vinylpyridine), and poly(2,6‐dimethyl‐1,4‐phenylene oxide)

Poly(styrene‐co‐methacrylic acid) (PSMA) and poly(styrene‐co‐4‐vinylpyridine) (PS4VP) of different compositions were prepared and characterized. The phase behavior of these copolymers as binary PSMA/PS4VP mixtures or with poly(2,6‐dimethyl‐1,4‐phenylene oxide) (PPO) as PPO/PSMA or PPO/PS4VP and PPO/PSMA/PS4VP ternary blends was investigated by differential scanning calorimetry (DSC). This study showed that PPO was miscible with PS4VP containing up to 15 mol % 4‐vinylpyridine (4VP) but immiscible with PS4VP‐30 (where the number following the hyphen refers to the percentage 4VP in the polymer) and PSMA‐20 (where the number following the hyphen refers to the percentage methacrylic acid in the polymer) over the entire composition range. To examine the morphology of the immiscible blends, scanning electron microscopy was used. Because of the hydrogen‐bonding specific interactions that occurred between the carboxylic groups of PSMA and the pyridine groups of PS4VP, chloroform solutions of PSMA‐20 and PS4VP‐15 formed interpolymer complexes. The obtained glass‐transition temperatures (T_g's) of the PSMA‐20/PS4VP‐15 complexes were found to be higher than those calculated from the additivity rule. Although, depending on the content of 4VP, the shape of the T_g of the PPO/PS4VP blends changed from concave to S‐shaped in the case of the miscible blends, two T_g were observed with each PPO/PS4VP‐30 and PPO/PS4VP‐40 blend. The thermal stability of the PSMA‐20/PS4VP‐15 interpolymer complexes was studied by thermogravimetry. On the basis of the obtained results, the phase behavior of the ternary PPO/PSMA‐20/PS4VP‐15 blends was investigated by DSC. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effect of thermal treatments on the miscibility of poly(vinyl cinnamate) binary blends

Poly(vinyl cinnamate) (PVCN) could undergo thermal or photo crosslinking. PVCN was previously found to be miscible with poly(vinyl phenol) (PVPh) [also named poly(hydroxystyrene)]. In this article, the miscibility between PVCN with or without thermal crosslinking and poly(styrene‐co‐hydrostyrene) (designated as MPS) was investigated. PVCN was determined to be miscible with MPS with 15% of hydroxystyrene (MPS‐15) at two compositions but partially miscible or immiscible at PVCN/MPS‐15(50/50) composition. For MPS with 5% of hydroxystyrene (MPS‐5), two T_g values were detected indicating mostly immiscibility. However, PVCN after thermal crosslinking was determined to be miscible with both MPS‐5 and MPS‐15. Immiscibility was found between thermally crosslinked PVCN and PVPh different from miscibility in the original PVCN/PVPh blends. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Independent control of sol molar mass and gel content in acrylate polymer/latexes

Poly n-butylacrylate latexes are commonly used as the base ingredient in the formulation of pressure sensitive adhesives, PSA. In the typical starved semi-batch process carried out to produce this latex and due to the non-linear nature of the kinetics, chain transfer to polymer plus bimolecular termination by combination, polymer networks are produced. The molar mass distribution of these polymer latexes is characterized by a soluble and an insoluble fraction, so-called gel. Both fractions strongly affect the adhesion properties, but unfortunately the independent control of these properties is a difficult task, that has not been solved yet. In this work, the concentrations of chain transfer agent and cross-linker were used in an attempt to exercise control over the molar mass of the soluble part and the amount of gel polymer. It was found that by simultaneously manipulating both variables it was possible to modify the gel content of the polymer without completely sacrificing the sol molar mass. The adhesion properties, tack and resistance to shear, measured on films cast from the latex demonstrated that a good PSA can be obtained by properly balancing the amount of CTA and cross-linker in the formulation.     

Miscible blends of poly(4‐vinyl phenol)/poly (trimethylene terephthalate)

A new miscible blend of all compositions comprising poly(4‐vinyl phenol) (PVPh) and poly(trimethylene terephthalate) (PTT) was discovered and reported. The blends exhibit a single composition‐dependent glass transition and homogeneous phase morphology, with no lower critical solution temperature (LCST) behavior upon heating to high temperatures. Interactions and spherulite growth kinetics in the blends were also investigated. The Flory–Huggins interaction parameter (χ₁₂) and interaction energy density (B) obtained from analysis of melting point depression are negative (χ₁₂ = ?0.74 and B = ?32.49 J cm^?3), proving that the PVPh/PTT blends are miscible over a wide temperature range from ambient up to high temperatures in the melt state. FTIR studies showed evidence of hydrogen‐bonding interactions between the two polymers. The miscibility of PVPh with PTT also resulted in a reduction in spherulite growth rate of PTT in the miscible blend. The Lauritzen–Hoffman model was used to analyze the spherulite growth kinetics, which showed a lower fold‐surface free energy (σ_e) of the blends than that of the neat PTT. The decrease in the fold‐surface free energy has been attributed to disruption of the PTT lamellae exerted by PVPh in an intimately interacted miscible state. Copyright © 2004 Society of Chemical Industry     

Investigation of the effect of chain rigidity on orientation of polymer blends: the case of poly(vinyl phenol)/poly(ethylene terephthalate) blends

Orientation of amorphous, miscible poly(vinyl phenol) (PVPh)-poly(ethylene terephthalate) (PET) blends is studied using experimental and modelling techniques. Up to 50 wt% PVPh, the blends are semi-crystalline and were therefore not studied. At 60 wt% PVPh, no crystallisation was observed using either differential scanning calorimetry or X-ray diffraction. For the 60wt% PVPh blend, FTIR dichroism determination showed that orientation was relatively high (0.09 at a λ=3.4) and similar for both polymers. Above 60 wt% PVPh, however, no appreciable orientation was detected. In order to gain insights about the deformation phenomena in polymer blends, atomistic models of the 60 wt% PVPh composition were built using the Meirovitch approach. These were found in good agreement with X-ray diffraction, and exhibit a fair degree of interpenetration as estimated visually and by comparing intermolecular pair distribution functions. Significant hydrogen bonding was found: 8% of carbonyl oxygens and 1% of carboxylate oxygens of PET are bound to PVPh. Deformation simulations were performed using the Parrinello-Rahman deformation scheme. Orientation of PVPh and PET in the blend was found equivalent to that observed in pure polymers simulations. PET orientation followed the aggregate model and was more oriented than PVPh by a factor of two. It was concluded that the similarity in orientation of the two polymers in the blend, which was observed experimentally on quenched samples, could be due to a combination of different deformation-induced orientation followed by distinct relaxation mechanism and relaxation times for both polymers.     

PMMA‐modified divinylester/styrene resins: Phase diagrams and morphologies

Binary and ternary experimental cloud‐point curves (CPCs) for systems formulated with a low molar mass synthesized divinylester (DVE) resin, styrene (St), and poly(methyl methacrylate) (PMMA) were determined. The CPCs results were analyzed with the Flory–Huggins (F‐H) thermodynamic model taking into account the polydispersity of the DVE and PMMA components, to calculate the different binary interaction parameters and their temperature dependences. The St‐DVE system is miscible in all the composition range and down to the crystallization temperature of the St; therefore, the interaction parameter expression reported for a higher molar mass DVE was adapted. The interaction parameters obtained were used to calculate the phase diagrams of the St‐PMMA and the DVE‐PMMA binary systems and that of the St‐DVE‐PMMA ternary system at three different temperatures. Quasiternary phase diagrams show liquid–liquid partial miscibility of the St‐PMMA and DVE‐PMMA pairs. At room temperature, the St‐DVE‐PMMA system is miscible at all compositions. Final morphologies of PMMA‐modified cured St‐DVE materials were generated by polymerization‐induced phase separation (PIPS) mechanism from initial homogeneous mixtures. SEM and TEM micrographs were obtained to analyze the generated final morphologies, which showed a direct correlation with the initial miscibility of the system. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4539–4549, 2006     

Interactions in miscible blends and complexes of poly(N-acryloylmorpholine) with poly(p-vinylphenol)

Poly(p-vinylphenol) (PVPh) and poly(N-acryloylmorpholine) (PAcM) form interpolymer complexes in ethanol/water (1:1) solution. However, only ordinary blends are obtained from dimethylformamide solution. Each of the complexes and ordinary blends shows one composition-dependent glass transition temperature, indicating its single-phase nature. Fourier transform infrared spectroscopy and ¹³C solid-state nuclear magnetic resonance spectroscopy reveal the existence of hydrogen-bonding interactions between the hydroxyl groups of PVPh and the carbonyl groups as well as the ether oxygen of PAcM in the blends and complexes. In addition, X-ray photoelectron spectroscopy shows that the nitrogen atoms in PAcM are also involved in hydrogen-bonding interactions. Measurements of proton spin-lattice relaxation time in the rotating frame, T_1ρ(H), reveal that each of the complexes and ordinary miscible blends has one composition-dependent T_1ρ(H), indicating an intimate mixing on a scale of about 1.5 nm. The blends show a higher degree of surface enrichment of PVPh than the complexes.     

Shear and elongational flow properties of peroxide‐modified wood/low‐density polyethylene composite melts

Adding fillers to a polymer melt may result in a strain softening behavior in elongational flow in long‐chain branched materials, showing strain‐hardening behavior when compared with unfilled one. To improve the strain‐hardening properties in wood/LDPE composites, the effect of peroxide concentration on both the molecular architecture and molar mass distribution, and the rheological quantities in shear and elongation is studied. Addition of wood flour increases the viscosity according to a logarithmic mixing rule, as expected from the large particle size and the filler fractions used. The peroxide has multiple effects on the molar architecture of the polymer. First, a gel fraction of cross‐linked material is formed, the concentration of gel being dependent of the amount of peroxide used. Second, a higher molar mass component is detected, leading to higher value of M_w and to a broader molar mass distribution. Finally, the degree of long‐chain branching unexpectedly decreases with increasing peroxide content. The changes in molecular architecture are hardly influenced by addition of the wood flour. The peroxide treatment leads to an improved strain‐hardening behavior, detected by elongational viscosity and melt strength measurements. However, the addition of wood flour decreases the amount of strain hardening.POLYM. COMPOS., 33:2084–2094, 2012. © 2012 Society of Plastics Engineers     

Miscibility and crystallization of biodegradable poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate)/poly(vinyl phenol) blends

Miscibility and crystallization of biodegradable poly (3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate) (PHBHHx)/poly(vinyl phenol) (PVPh) blends were investigated in this work. PHBHHx is miscible with PVPh over the whole composition range as evidenced by the single composition dependent glass transition temperature and the depression of equilibrium melting point of PHBHHx in the blends. The overall crystallization rates decrease with increasing crystallization temperature for both neat PHBHHx and its blends with PVPh; moreover, the overall crystallization rates are slower in the PHBHHx/PVPh blends than in neat PHBHHx at the same crystallization temperature. Blending with PVPh may change the crystallization mechanism of PHBHHx in the blends compared with that of neat PHBHHx. Both neat PHBHHx and the PHBHHx/PVPh blends exhibit a crystallization regime II to III transition. The crystal structure of PHBHHx is not modified in the PHBHHx/PVPh blends; however, the values of crystal layer thickness, amorphous layer thickness, and long period all become larger with increasing PVPh content in the blends. POLYM. ENG. SCI., 2012. © 2011 Society of Plastics Engineers     

Super‐macroporous dextran cryogels via UV‐induced crosslinking: synthesis and characterization

Cryogenic treatment and UV irradiation were exploited for the preparation of super‐macroporous cryogels from non‐modified high‐molar‐mass dextran. The photo‐crosslinking process was initiated by (4‐benzoylbenzyl)trimethylammonium chloride and N,N′‐methylenebisacrylamide (BAAm) was used as a crosslinking agent. Gel fraction yield and degree of swelling of the dextran cryogels were determined gravimetrically. Cryogel morphology and mechanical properties were studied using environmental scanning electron microscopy and dynamic rheological measurements, respectively. The effects of dextran concentration in the initial polymer solution, polymer molar mass and BAAm content on the crosslinking efficacy, physico‐mechanical properties and morphology of the cryogels were evaluated. The dextran cryogels were assessed as carriers of the model water‐soluble drug metoprolol. © 2017 Society of Chemical Industry     

Modification of textile fibres with nanolayers of fluorine-containing interpolymer complexes

A method of modifying textile fibres based on application by layers of an anchor polymer and a fluorine containing SF capable of forming a nanosize surface interpolymer complex that gives the fibres assigned properties is proposed. Formation of the interpolymer complexes of fluorine-containing SF with cationic water-soluble polymers was investigated. It was found that particles from 52 to 59 nm in size are formed as a result of the intermolecular interaction, and a modifying nanosize layer forms when they are deposited on the fibres and treated with heat. Surface modification is not inferior in quality to modification using polymer nanodispersions — synthetic fluorine-containing latexes. The modifying effect of the interpolymer complexes is almost independent of the nature of the textile materials.     

Polyurethane membrane prepared via a dry/wet phase inversion method for protein adsorption

Hydroxyl‐terminated polybutadiene (HTPB)‐ and 4,4′‐dicyclohexyl‐methane (H₁₂MDI)‐based polyurethanes (PUs) were synthesized by solution polymerization. PU membranes were prepared by a dry/wet phase inversion method. Protein adsorption ratio of fibrinogen to albumin (F/A molar ratio) was measured. Low F/A molar ratio was found on these PUs. It was found that surface composition of these PUs has a subtle effect on F/A adsorption molar ratio. The F/A molar ratio was increased as the increase of hard segment content distributed on the surface. The variation of surface composition of these membranes and the effect on the F/A molar ratio were investigated by the difference in surface energy between nonpolar HTPB soft segment and polar hard segment, concentration, and temperature of coagulation medium, polymer content, and alcohol type. The CO/CC ratio, frequency shift, and difference (Δν) as a measure of polymer homogeneity and the average strength of interpolymer hydrogen bonds were utilized to study the surface composition. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1334–1340, 1999