PET/PTT合金非等温结晶行为的研究

采用差示扫描量热仪对熔融共混制备的聚对苯二甲酸乙二醇酯（PET）/聚对苯二甲酸丙二醇酯（PTT）合金的非等温结晶行为进行研究。结果表明,在相同的降温速率时, 随着PTT含量的增加,PET/PTT合金结晶峰温度向低温方向移动,而且当合金中PET与PTT含量接近时,合金样品出现了双重结晶峰;在降温结晶的过程中,随着降温速率的增大,各合金样品结晶峰温度均降低,其结晶峰均宽化;采用Jeziorny法对上述非等温结晶过程进行了分析,分析结果表明,随着降温速率的增大,各合金样品非等温结晶速率常数增加,其Avrami指数在1~5之间,并且逐渐减小。     

PTT的等温与非等温结晶动力学研究

采用DSC方法对聚对苯二甲酸丙二酯进行等温与非等温结晶动力学研究,利用不同动力学模型对其结晶过程进行分析.结果表明,在等温结晶过程中,Avrami指数n和半结晶时间随着结晶温度的升高而增大,结晶速率常数K随着结晶温度的升高而减小;在非等温结晶的过程中,结晶动力学常数Zc和相对过冷度△Tc随着降温速率的提高而上升,Avr...     

PTT非等温结晶动力学研究

采用差示扫描量热仪对PTT进行非等温结晶研究。利用不同动力学模型对其结晶过程进行处理, 并将PTT与PET及PBT的非等温结晶过程进行对比。结果表明:Jeziorny方程和Ozawa方程都可以很好的 描述PTT,PET,PBT的非等温结晶过程;采用结合Avrami方程和Ozawa方程的处理方法,得到了3种聚酯的 结晶速率的大小关系:PBT>PTT>PET。通过计算Ziabicki结晶能力参数,得到3种聚酯的结晶能力的顺序 为:PBT>PTT>PET。     

聚对苯二甲酸丙二醇酯的非等温结晶动力学研究

采用DSC研究了聚对苯二甲酸丙二醇酯(PTT)在不同等速降温速率下的结晶过程,并利用由等温Avrami方程推导得到的两种不同的等速降温非等温结晶方程,研究了其结晶动力学,得出PTT的成核方式为异相成核,同时利用拟和法计算了PTT的结晶能力,发现在同等条件下PTT的结晶能力大于PET。     

PTT／PET共混体系结晶行为和形态研究

利用差示扫描量热仪、正交偏光显微镜研究了聚对苯二甲酸丙二醇酯(PTT)、聚对苯二甲酸乙二醇酯(PET)及PTT/PET共混体系(质量比为25∶75)的结晶行为、形态和等温结晶动力学。结果表明,PTT/PET共混物中,少量的PTT部分地起到了成核作用,但在一定程度上阻碍了PET链段规则地进入晶格,影响了结晶速率。偏光显微镜观察到PET、PTT和PTT/PET共混物在120℃下1、20min的溶液滴膜有较清晰的球晶。     

异山梨醇改性PTT共聚酯的合成及其非等温结晶动力学研究

以异山梨醇(IS)作为第三单体,对苯二甲酸和1,3-丙二醇为基本原料,在5 L缩聚釜中制得聚对苯二甲酸1,3-丙二醇酯(PTT)及不同IS含量的对苯二甲酸1,3-丙二醇-异山梨醇共聚酯(PTTI);使用核磁共振氢谱仪分析PTT及PTTI的结构,使用差式扫描量热仪测定PTT和PTTI在不同降温速率下的降温曲线,并采用Jeziorny法研究PTT及PTTI的非等温结晶动力学。结果表明：在PTTI试样的核磁共振氢谱中,化学位移为4.296～5.706处出现了IS上8个氢原子所形成的特征峰,表示IS成功参与了PTT的反应;随着降温速率的增加,PTT及PTTI的结晶温度降低,结晶曲线变宽,结晶能力变差;在相同降温速率下,相比PTT,加入IS后的PTTI的非等温结晶动力学速率常数变大,结晶温度降低;IS的加入不利于PTT结晶。     

PBT/PTT合金的非等温结晶行为

采用差示扫描量热法(DSC)研究了聚对苯二甲酸丁二酯(PBT)/聚对苯二甲酸丙二酯(PTT)合金的非等温结晶动力学.随着降温速率的增大,PBT/PTT合金的结晶峰温均降低,结晶峰均加宽.采用Jeziorny法、莫志深法和Flyn-Wall-Ozawa法分析非等温结晶过程,Jeziorny法能够描述PBT/PTT合金的初期结晶过程,对后期结晶存在一定偏差,各PBT/PTT合金的结晶维数变化不大;莫志深和Flyn-Wall-Ozawa法能很好地描述PBT/PTT合金的非等温结晶过程,随PTT含量增加,由Flyn-Wall-Ozawa法求得PBT/PTT合金的活化能呈增加趋势.相对结晶度为0.5,m(PBT)/m(PTT)分别为90∶10,70∶30,50∶50时,PBT/PTT合金的活化能分别为-201.9,-116,0,-66.6 kJ/mol;相对结晶度为0.5时,m(PBT)/m(PTT)为50∶50的合金活化能比PTT(-77.4 kJ/mol)还高.     

PTT/PE共混体系结晶动力学及结晶形态研究

采用差示扫描量热法(DSC)研究了聚对苯二甲酸丙二醇酯/聚乙烯(PTT/PE)共混体系的非等温结晶动力学,通过热台偏光显微镜(POM)对共混物在等温条件下的结晶形态进行了研究。结果发现:PTT/PE共混体系各样品的结晶峰温度随着冷却速率的提高而下降,而半结晶时间t1/2随着冷却速率的提高而提高;结晶动力学常数Zc随着冷却速率的提高而下降,表明共混体系的结晶速率随着冷却速率的提高而降低;在POM观察的时间范围内各样品的球晶尺寸随着时间的延长而增大,PTT/PE(30/70)共混体系在190℃结晶时,球晶尺寸较大,即球晶生长较快。     

PTT/蒙脱土复合材料非等温结晶行为的研究

采用差示扫描量热仪对熔融共混制备的聚对苯二甲酸丙二醇酯(PTT)/蒙脱土(MMT)复合材料非等温结晶行为进行了测试分析。研究结果表明:在相同的降温速率时,随着MMT含量的增加,PTT/MMT复合材料的结晶峰温向高温方向移动,结晶峰变窄,半结晶期也缩短;随着降温速率的增大,PTT/MMT复合材料的结晶峰温向低温方向移动,半结晶期变短。采用Ozawa法处理了PTT/MMT复合材料的非等温结晶过程,结果表明:MMT的加入改变了PTT的成核机理,加快了PTT的结晶速率。     

PET/石膏晶须复合材料的非等温结晶过程研究

用差示扫描量热仪(DSC)对PET/石膏晶须复合材料的非等温结晶过程的结晶行为进行了研究,并利用莫氏理论得到了复合材料的动力学参数F(T)和a。F(T)值随着结晶度的增加,逐渐增大;a值几乎相同,近似常数(在1.5~1.8之间)。     

聚乙二醇增塑聚乳酸的非等温结晶动力学研究

采用DSC方法对聚乙二醇(PEG)增塑聚乳酸的非等温结晶动力学进行了研究。结果表明,PEG的加入明显提高了聚乳酸的结晶速度。对所得数据分别用Ozawa方程和莫志深方法进行了处理,发现在给定温度范围里非等温结晶时,PLA/PEG主要是以均相成核的三维生长方式结晶;PLA的结晶速度随着PEG分子质量的增加而升高。     

Nonisothermal and isothermal crystallization kinetics of nylon‐12

The isothermal and nonisothermal crystallization behavior of Nylon 12 was investigated using differential scanning calorimetry (DSC). An Avrami analysis was used to study the isothermal crystallization kinetics of Nylon 12, the Avrami exponent (n) determined and its relevance to crystal growth discussed and an activation energy for the process evaluated using an Arrhenius type expression. The Lauritzen and Hoffman analysis was used to examine the spherulitic growth process of the primary crystallization stage of Nylon 12. The surface‐free energy and work of chain folding were calculated using a procedure reported by Hoffmann and the work of chain folding per molecular fold (σ) and chain stiffness of Nylon 12 (q) was calculated and compared to values reported for Nylons 6,6 and 11. The Jeziorny modification of the Avrami analysis, Cazé and Chuah average Avrami parameter methods and Ozawa equation were used in an attempt to model the nonisothermal crystallization kinetics of Nylon 12. A combined Avrami and Ozawa treatment, described by Liu, was used to more accurately model the nonisothermal crystallization kinetics of Nylon 12. The activation energy for nonisothermal crystallization processes was determined using the Kissinger method for Nylon 12 and compared with values reported previously for Nylon 6,6 and Nylon 11. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Nonisothermal crystallization kinetics of polyoxymethylene/montmorillonite nanocomposite

The nonisothermal crystallization kinetics of polyoxymethylene (POM), polyoxymethylene/Na–montmorillonite (POM/Na–MMT), and polyoxymethylene/organic–montmorillonite (POM/organ–MMT) nanocomposites were investigated by differential scanning calorimetry at various cooling rates. The Avrami analysis modified by Jeziorny and a method developed by Mo were employed to describe the nonisothermal crystallization process of POM/Na–MMT and POM/organ–MMT nanocomposites. The difference in the values of the exponent n between POM and POM/montmorillonite nanocomposites suggests that the nonisothermal crystallization of POM/Na–MMT and POM/organ–MMT nanocomposites corresponds to a tridimensional growth with heterogeneous nucleation. The values of half‐time and the parameter Z_c, which characterizes the kinetics of nonisothermal crystallization, show that the crystallization rate of either POM/Na–MMT or POM/organ–MMT nanocomposite is faster than that of virgin POM at a given cooling rate. The activation energies were evaluated by the Kissinger method and were 387.0, 330.3, and 328.6 kJ/mol for the nonisothermal crystallization of POM, POM/Na–MMT nanocomposite, and POM/organ–MMT nanocomposite, respectively. POM/montmorillonite nanocomposite can be as easily fabricated as the original polyoxymethylene, considering that the addition of montmorillonite, either Na–montmorillonite or organ–montmorillonite, may accelerate the overall nonisothermal crystallization process. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 2281–2289, 2001     

PET/PTT共混体系的非等温结晶动力学研究

采用DSC方法研究了PET/PTT共混体系的非等温结晶动力学,研究发现:PET/PTT共混体系各样品的结晶峰温度和半结晶时间t1/2随着冷却速率的提高而下降;结晶动力学常数Zc随着冷却速率的提高而增加,表明共混体系的结晶速率随着冷却速率的提高而增大;Zc随着PTT含量的增加而逐渐减小,在其含量达40%￣50%时出现了最小值。     

Synthesis and nonisothermal crystallization kinetics of biodegradable poly(ethylene terephthalate-co-ethylene succinate)s

In the current work, a series of biodegradable poly(ethylene terephthalate-co-ethylene succinate)s (P[ET-co-ES]s) were prepared via a traditional melting polycondensation method. First of all, the structures of prepared copolymers were characterized by nuclear magnetic resonance and Fourier transform infrared measurements. Meanwhile, the thermal properties of prepared samples were analyzed by differential scanning calorimetry and thermogravimetric analysis measurements, respectively. Subsequently, the mechanical properties of the P(ET-co-ES)s were evaluated, the tensile strength of P(ET-co-ES)s decreased with increasing of PES content in copolymer, however, corresponding P(ET-co-ES)s exhibited better elongation at break. Next, the biodegradability of P(ET-co-ES)s was evaluated using lipase as degrading enzyme. The results presented that the biodegradability of P(ET-co-ES)s improved with PES content, the corresponding results were supported by scanning electron microscopy test. Finally, the Mo's modified Avrami equation was employed to analyze the nonisothermal crystallization kinetics of prepared copolymers. The results showed the addition of the PES component improved the crystallization properties of the prepared P(ET-co-ES)s. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48422.     

Isothermal crystallization kinetics of commercially important polyalkylene terephthalates

The isothermal crystallization kinetics of virgin, melt‐mixed, and nucleated specimens of polyethylene terephthalate (PET), polypropylene terephthalate (PPT), and polybutylene terephthalate (PBT) were measured. The purpose of the study was to determine the difference in crystallization rate of PPT, which is to be commercially available in the near future, to the extensively studied, commercially important polyalkylene terephthalates PET and PBT. At equivalent supercooling, the crystallization rate of PPT was between that of PET and PBT, with PBT being the fastest crystallizing polymer. Melt‐mixing virgin materials resulted in a substantial increase in the crystallization rate for all three polyalkylene terephthalates. The addition of talc or sodium stearate as a nucleating agent resulted in a further increase in crystallization rate for all three polyesters. Although the addition of talc or sodium stearate to PPT and PET greatly enhanced crystallization rate, these nucleating agent–containing materials still did not crystallize as fast as PBT melt‐mixed in the absence of any intentionally added nucleating agents. Analysis of the crystallization kinetic data using the Avrami equation showed that melt‐mixing and the addition of sodium stearate resulted in an increase in the average Avrami exponent. This result suggested a change in the mechanism of nucleation toward more sporadic nucleation. For the sodium stearate–nucleated materials, the Avrami exponent was found to increase with increasing crystallization temperature, but a precise explanation of this behavior could not be provided without a knowledge of crystallite morphology. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 1296–1307, 2000     

Nonisothermal crystallization kinetics of linear metallocene polyethylenes

The effect of weight‐average molecular weight (M_w) on the nonisothermal crystallization kinetics of linear metallocene polyethylene (m‐PE) was studied with modulated differential scanning calorimetry. Six linear m‐PEs of molecular weights in the range 122–934 kg/mol were prepared by gas‐phase polymerization. The cooling rate (R) was varied in the range 2–20°C/min, and it significantly affected the crystallization behavior. M_w had a weak influence on both the peak crystallization temperature and the crystallization onset temperature. All m‐PEs showed primary and secondary crystallizations. At both low and high R's, the crystallinity showed a significant drop (～ 30%) when M_w was increased from 122 to 934 kg/mol. At low R's (< 10°C/min), the rate parameters in the modified Avrami method [primary rate constant (k_R)] and Mo method [F(T)] of analyses agreed in suggesting that an increased M_w slowed the rate of crystallization. The M_w dependency of k_R followed the Arrhenius type (k_R = k_Roe²⁸¹/M_w, where k_Ro is a rate‐dependent constant). However, at higher R's, k_R approached a constant value. The order parameters obtained by the different methods of analysis (n and α) were independent of M_w, which suggests that the crystal type remained the same. Hoffman–Lauritzen theory was used for data analysis, and activation energy per segment showed a significant decrease, from 225.0 to 11.8 kJ/mol, when M_w was increased from 152 to 934 kg/mol. Finally, all methods of analysis suggested a significant effect of M_w on slowing the overall crystallization process. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008