环氧丙烯酸酯/乙烯基醚光聚合反应动力学研究

以二缩乙二醇二乙烯基醚 (DVE -3 )为活性稀释剂 ,研究其与环氧丙烯酸酯 (EOA)所组成的光聚合体系在自由基型光引发剂下引发的光聚合反应动力学及其影响因素。DVE -3含量越大 ,EOA/DVE -3体系的转化率越低。体系粘度的提高有利于提高其反应速率。若在环氧丙烯酸酯中引入马来酸酯结构 ,则马来酸酯的含量越大 ,体系的转化率越高 ,马来酸酯结构的引进 ,可以降低体系聚合后残余的双键含量。     

Photo-DSC cure kinetics of vinyl ester resins II: influence of diluent concentration

The photopolymerization kinetics of two commercial vinyl ester resins (VERs) and a model VER photoinitiated by the camphorquinone/amine photoinitiator system were monitored using isothermal DSC. A decrease in styrene concentration in model VERs was found to raise the rate of photopolymerization. In contrast, when the styrene was replaced by a monomethacrylate diluent, the photopolymerization rate passed through a maximum near 70 wt% diluent monomer. This difference in the variation of the rate of polymerization with decreased monomer concentration was attributed to the competition of the effects of the higher reactivity of the methacrylyl radical relative to the styryl radical and the lower termination rate for divinyl-rich systems (both of which tend to raise the maximum polymerization rate) and the effects of the reduction in the initiation efficiency and decrease in k_p due to increased fraction of pendant double bonds (which lower the polymerization rate) when the concentration of diluent monomer was reduced. Subsequent dark polymerization was observed during a temperature ramp and the onset of polymerization was independent of resin composition due to vitrification effects during the isothermal photocuring stage. The kinetics during the dark polymerization stage was discussed in terms of the radical concentration and the propagation rate constant. Increases in the concentration of either diluent monomer raised the extent of isothermal cure during the isothermal polymerization because vitrification was delayed by the lower crosslink density and the plasticizing effect of the diluent. Higher levels of diluent also raised the maximally attainable conversion due to reduced topological restrictions for reaction in networks of lower crosslink density.     

Polymers from renewable resources: XIX: Synthesis and characterization of copolymers from cardanyl acrylate and vinyl monomers

A large number of copolymers have been prepared from cardanyl acrylate on suspension polymerisation with vinyl monomers like methyl acrylate, ethyl acrylate, butyl acrylate, etc. These copolymer beads are almost uniform in size. Infrared spectral and swelling behaviour studies explain their various characteristics. The thermal behaviour of the copolymer beads has been studied with the help of a new computer method known as the LOTUS package method.     

Effect of photoinitiator segregation on polymerization kinetics in lyotropic liquid crystals

Through photopolymerization lyotropic liquid crystalline (LLC) phases may be templated onto organic polymers to yield highly complex nanostructures. In order to understand the unique polymerization behavior controlling structural development in LLC media, the polymerization kinetics in these systems have been studied using several commercially available photoinitiators. Although monomer segregation and diffusional restrictions largely govern the kinetics in these systems, the initiation may also be influenced by changing LLC order and composition. Nonpolar monomers, which partition to the oil soluble domains of the LLC phase typically display the fastest rate of polymerization in micellar aggregates. The rate decreases in phases with larger nonpolar domains due to decreasing localized double bond concentration. Polar monomers exhibit the opposite behavior. However, the segregation of photoinitiator may contribute to significantly different trends in polymerization behavior. Relatively mobile initiators, displaying favorable interaction with water, yield a trend in polymerization that is governed primarily by monomer and diffusional effects. When bulkier, hydrophobic initiators are used, the polymerization appears much less dependent on these effects. Rather than the decreasing rate usually observed at higher surfactant concentrations, polymerization of oil soluble monomers with the less mobile initiators shows the opposite trend of increasing rate at higher surfactant concentration. This behavior likely results from increasing initiator efficiency of the bulky, hydrophobic initiator in the surfactant rich environment.     

Synthesis and photopolymerization of acrylic acrylate copolymers

Acrylate‐functionalized copolymers were synthesized by the modification of poly(butyl acrylate‐co‐glycidyl methacrylate) (BA/GMA) and poly(butyl acrylate‐co‐methyl methacrylate‐co‐glycidyl methacrylate). ¹³C‐NMR analyses showed that no glycidyl methacrylate block longer than three monomer units was formed in the BA/GMA copolymer if the glycidyl methacrylate concentration was kept below 20 mol %. We chemically modified the copolymers by reacting the epoxy group with acrylic acid to yield polymers with various glass‐transition temperatures and functionalities. We studied the crosslinking reactions of these copolymers by differential scanning calorimetry to point out the effect of chain functionality on double‐bond reactivity. Films formed from acrylic acrylate copolymer precursors were finally cured under ultraviolet radiation. Network heterogeneities such as pendant chains and highly crosslinked microgel‐like regions greatly influenced the network structure and, therefore, its viscoelastic properties. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 753–763, 2002     

Cationic photopolymerization of bisphenol-A-based vinyl ether systems

2,2-Bis{4-[2-(vinyloxy)ethoxy]phenyl}propane (BPA) monomer was synthesized and its cationic photopolymerization with triethyleneglycol divinyl-ether (DVE3) investigated. Real-time FT-IR kinetic investigations showed, in the presence of DVE3 monomer an increase of the photopolymerization rate and of the final vinyl ether double bond conversion.     

Percolation of glassy regions during photopolymerization of epoxy acrylate in DMF

The gelation of epoxy acrylate (EA) 80% and tripropyleneglycol diacrylate (TPGDA) 20% was studied through the use of photo-differential scanning calorimetric (photo-DSC) technique in the presence of a thioxanthone based initiator. Photo-induced polymerization reactions were performed under identical conditions of temperature, initiator concentration and UV light intensity in various N,N-dimethylformamide (DMF) contents. Photo-DSC technique allowed us to monitor the gelation without disturbing the system mechanically, and to test the universality of the gelation as a function of DMF content. During gelation, it was observed that all conversion curves presented useful sigmoidal behavior which was predicted by employing a percolation model. Observations around the glass transition point, t_g, revealed that gel fraction exponent β obeyed the percolation picture. A significant solvent effect on the photopolymerization kinetics of EA/TPGDA was observed with changes in DMF content. DMF is used as solvent, which acts as a diluent and proton donor during photogelation.     

Understanding multivinyl monomer photopolymerization kinetics through modeling and GPC investigation of degradable networks

Multivinyl monomers that react to form highly crosslinked, biodegradable networks are being developed as scaffolds for tissue engineering and vehicles for drug delivery; however, this work demonstrates their usefulness in characterizing better the complexities of the kinetics and structural evolution during crosslinking photopolymerization. The molecular weight distributions (MWDs) of the degradation products of networks formed through the free radical photopolymerization of multivinyl monomers validate a novel kinetic model to test hypotheses as to the important kinetic mechanisms during crosslinking. The kinetic model, in conjunction with the experimental results for the degradable network, provides insight into the fundamental termination mechanisms (i.e. chain length dependent termination (CLDT), chain transfer to either a unimolecular species or polymer, and the accumulation of persistent radicals) that control the MWD of the backbone kinetic chains throughout the polymerization. Specifically, the importance of CLDT during autoacceleration and the impact of light intensity on the MWD of the backbone kinetic chains are presented.     

Study of in-situ photopolymerization of chiral liquid crystal acrylate

The effect of the smectic and isotropic phase on the photo-polymerization of the chiral liquid crystalline 4-acryloxy-undecanyloxy-4′-[S(?)-2-methylbutyloxy]-biphenyl (monomer ( I )) was studied using FTIR. The effect of temperature on the birefringence of surface-oriented monomer ( I ) and its polymer obtained by in-situ photopolymerization was also investigated. The results show that photopolymerization in the isotropic phase proceeds at a higher rate than in the smectic phase, when monomer conversion is less than 60%; however, when monomer conversion is above 60%, the photopolymerization rate is independent of the initial phase state of monomer ( I ), and a highly oriented liquid crystalline polyacrylate film can be prepared by in-situ photopolymerization of the surface-oriented chiral acrylate ( I ).     

氯乙烯-丙烯酸异辛酯共聚树脂的合成与表征

通过连续滴加预乳化丙烯酸异辛酯(EHA)单体,采用悬浮聚合方法合成了氯乙烯(VC)/EHA共聚树脂,对共聚树脂的颗粒特性、加工性能和力学性能等进行了研究。随着单体配比[m(EHA)∶m(VC)]的增加,共聚树脂颗粒的孔隙率、增塑剂吸收量和玻璃化温度降低,塑化时间和转矩缩短,加工性能逐渐变好,加工试片的硬度和拉伸强度降低,冲击强度略增大。     

Revisiting aromatic thiols effects on radical photopolymerization

Influence of thiols on kinetics of acrylate radical photopolymerization in the presence and absence of photoinitiators was studied. The kinetics was monitored by infrared absorption and photo-differential scanning calorimetry. It was found that aromatic thiols at concentrations, <0.5% (∼0.05 M), can accelerate radical photopolymerization. Initiation of radical photopolymerization by some aromatic thiols in the absence of conventional photoinitiators was observed. As well as expected inhibition of photopolymerization at higher concentration of aromatic thiols due to chain transfer was detected. A ground state charge-transfer complex formation between thiols and benzoin based photoinitiators was detected.Mechanism of thiols participation in photopolymerization involving reduction of oxygen inhibition and dissociation of charge-transfer complexes is discussed.     

Photopolymerization kinetics of poly(acrylate)-clay composites using polymerizable surfactants

Photopolymerization kinetics of polymer-clay nanocomposite systems utilizing polymerizable quaternary ammonium surfactants as dispersants were systematically investigated to determine the effects of surfactant type and clay morphology on polymerization behavior. For these studies, either polymerizable surfactants were mixed into a clay-monomer system or the surfactants were ionically anchored to clay surfaces and added to the monomer for in situ photopolymerization. Higher photopolymerization rates are observed with increasing polymerizable surfactant concentration, while no significant change or decreases in polymerization rate occur with incorporation of non-polymerizable surfactants. The higher rates observed for polymerizable surfactant systems are due to lower apparent termination rate parameters stemming from immobilization of the surfactants. For clay that is modified with ionically bonded quaternary ammonium surfactants, polymerization rates decrease in both polymerizable and non-polymerizable organoclay systems with increasing concentration, but this decrease is much smaller when polymerizable organoclays are utilized. For the same organoclay concentration, higher polymerization rates and double bond conversions result with increasing polymerizable surfactant concentration via cation exchange. Significant increases in polymerization rate also occur with increasing degree of clay exfoliation.     

Studies on cross-linked polyurethane acrylate-based electrolyte consisting of reactive vinyl/divinyl diluents

A series of cross-linked polyurethane acrylate (PUA) electrolytes have been prepared by using 4,4′-methylene bis(phenyl isocyanate), polyethylene glycol, hydroxyethyl methacrylate and different reactive vinyl/divinyl diluents, such as methyl methacrylate (MMA), ethyl acrylate and acrylonitrile, tripropylene glycol diacrylate (TPGDA). The electrolytes were prepared by UV radiation induced cross-linking of the PUA-diluent mixture followed by swelling in a liquid electrolyte (LP-30). Depending upon the composition of the components, these electrolytes exhibited a wide range of mechanical and electrical properties. The system containing MMA as reactive diluent showed highest conductivity, but poor mechanical properties and stability in the liquid electrolyte. The TPGDA cross-linked system possesses a good combination of ionic conductivity and stability in liquid electrolytes. These systems showed good compatibility with Li-electrodes and sufficient electrochemical stability to allow safe operation in rechargeable Li-batteries.     

Synthesis and photopolymerization kinetics of new flexible diacrylate and dimethacrylate crosslinkers based on C18 diacid

A series of new di(meth)acrylate monomers was synthesized from the reactions of methyl α-hydroxymethylacrylate (MHMA), ethyl α-hydroxymethylacrylate (EHMA), hydroxyethyl acrylate (HEA) and hydroxyethylmethacrylate (HEMA) with α,ω-C18 diacid chloride. The photopolymerization behavior and reaction kinetics of the synthesized monomers were investigated using photoinitiation with differential scanning calorimetry. The polymerization rates, conversions and kinetic constants for propagation and termination were determined for each of the monomers. The maximum rate of polymerizations of the diacrylate monomers was higher than that of the dimethacrylate monomers and followed the order: HDDA (1,6-hexanediol diacrylate)>HEA-C18>EHMA-C18∼HEMA-C18>MHMA-C18. The total conversions obtained were 78, 75, 72, 64 and 69% for MHMA-C18, EHMA-C18, HEMA-C18, HEA-C18 and HDDA, respectively, indicating comparable or higher conversions for methacrylates despite their lower rates of polymerization. Propagation and termination mechanisms of the monomers were investigated by plotting propagation and termination rate constants as a function of conversion.     

氯乙烯-丙烯酸丁酯共聚树脂的工业化生产

在7m3聚合釜中采用悬浮聚合工艺工业化生产了氯乙烯-丙烯酸丁酯共聚树脂,在小试配方基础上调整了分散剂的配比和用量,采用在线实时示踪剂色谱联动控制法控制丙烯酸丁酯的加入速度,并采用了聚合中途注水工艺及改进的防粘釜工艺。工业化产品符合企业标准要求,可在PVC型材生产中替代ACR使用。     

氯乙烯-丙烯酸酯-醋酸乙烯酯三元共聚乳液的研究开发

采用乳液接枝共聚和核壳聚合相结合的工艺，用十二烷基硫酸钠作为新型种子乳化剂合成氯乙烯－丙烯酸酯－醋酸乙烯酯接枝共聚乳液，该乳液经Autosizeu IIC型激光粒径仪和DSC曲线测定具有核壳结构特征，用于纺织织物涂层，各项指标完全达到产品所规定的标准，效果很好。     

Semicontinuous heterophase copolymerization of vinyl acetate and butyl acrylate

Vinyl acetate (VAc) and butyl acrylate (BuA) were copolymerized in heterophase by a semicontinuous process (unseeded) and compared with the seeded semicontinuous microemulsion polymerization of the same monomers. A mixture of sodium dodecyl sulfate (SDS) and poly(ethylene oxide) dodecyl ether (Brij‐35®) were used as surfactants. The effects of monomer addition rate (R_a) and surfactants concentrations (4 or 1 wt % with respect to the initial mixture of reaction) on polymer and latex properties were studied. High copolymer content latexes (24–36 wt %) with average particle diameters (D_p) from 38 to 55 nm and relatively narrow particle size distributions, high polymerization rates, weight ratios of polymer to surfactant (P/S) from 13.3 to 32.8 were obtained. The number‐average molecular weights (M_n) were between 96,000 and 188,000 g/mol. Homogeneous copolymer compositions were obtained throughout the reaction for both, seeded and unseeded processes, which is not possible by the usual batch microemulsion process. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Synthesis of acrylate modified vinyl chloride and vinyl isobutyl ether copolymers and their properties

With acrylic acid, butyl acrylate and methyl methacrylate as the monomers, acrylate modified vinyl chloride and vinyl isobutyl ether copolymers were prepared by solution polymerization. Firstly, vinyl chloride and vinyl isobutyl ether copolymers were grafted with acrylic monomers to obtain a product containing acrylate grafted vinyl chloride and vinyl isobutyl ether copolymers and polyacrylate, which was then neutralized by triethylamine and dispersed into water to get a self-emulsified emulsion. The acrylate modified vinyl chloride and vinyl isobutyl ether copolymers were characterized by Fourier transform infrared spectroscopy. The mean molecular weight of grafted polymer was determined by gel permeation chromatography, and the particle sizes and their distributions of the dispersions were measured by laser light scattering. The influences of initiator concentration, acrylate content, acrylic acid content and neutralization degree upon the properties of the modified copolymers were discussed. The results show that the emulsion will be with good storage stability, and the modified polymer will be with high water resistance, impact resistance and excellent adhesion when initiator concentration is 1.5%, acrylate content is 50%, acrylic acid content ranges from 9% to 11%, and neutralization degree is between 80% and 100%.     

Synthesis and properties of hyperbranched polyurethane acrylate used for UV curing coatings

The hyperbranched polyurethane acrylate (HPUA) was synthesized through the addition of hyperbranched polyurethane endcapped by hydroxyl groups (HPU-OH), with the semiadduct urethane monoacrylate (IPDI-HEA). The HPU-OH was prepared by the amidation reaction of diethanolamine with isophorone diisocyanate. The molecular structure of HPUA was characterized by FTIR and ¹H NMR analyses. The number average molecular weight and its polydispersity index were measured by GPC to be 7714 g mol⁻¹ and 1.24, respectively. The HPUA was blended with epoxy acrylate EB600 and difunctional monomer TPGDA in different ratios, and exposed to a UV lamp for photopolymerization in the presence of Runtecure 1104 as a photoinitiator at room temperature. The photopolymerization rate and final unsaturation conversion reached to the highest values with only 5 wt% HPUA addition, whereas decreased as further added. The tensile strength of UV-cured films was improved by adding less than 10 wt% HPUA without damaging the modulus, having the value of 62.56 MPa for EB₉₀HPUA₁₀ film. Besides, the elongation at break increased continuously with the addition of HPUA, reaching to 130% for EB₇₀HPUA₃₀ film. Moreover, the impact strength was greatly enhanced by the addition of HPUA, possessing nearly two times high for EB₇₀HPUA₃₀ film compared with pure EB600 film. However, the T_g decreased as HPUA was added from the DMTA measurements. According to the ratios of T_s/T_g the HPUA has good compatibility with EB600/TPGDA resin.