球形LiNi1/3Co1/3Mn1/3O2的合成及其电化学性能

以化学共沉淀法制备的球形Ni1/3Co1/3Mn1/3CO3为前驱体合成了球形LiNi1/3Co1/3Mn1/3O2,研究LiNi1/3Co1/3Mn1/3O2合成工艺对产物形貌的影响.结果表明直接以前驱体Ni1/3Co1/3Mn1/3CO3与Li2CO3反应合成的LiNi1/3Co1/3Mn1/3O2的一次颗粒较大,以前驱体分解后的氧化物与Li2CO3反应合成的LiNi1/3Co1/3Mn1/3O2的一次颗粒相对细小;合成的LiNi1/3Co1/3Mn1/3O2均为具有层状结构的纯相物质;球形正极材料LiNi1/3Co1/3Mn1/3O2充放电过程中存在一个材料活化的过程,在前10周期充放电时,电池容量处于增加的状态;在2.7～4.3 V的电压范围内1 C倍率下电池的放电比容量达到149 mA·h/g,0.2 C倍率下为158 mA·h/g,经50次循环后容量无衰减.     

正极材料LiNi0.8Co0.1Mn0.1O2的合成及电化学性能

将液相共沉淀法制备的Ni0.8Co0.iMn0.1(OH)2与LiOH·H2O混合,固相烧结合成微米级的LiNi0.8Co0.1Mn0.1O2正极材料.XRD谱表明,合成的LiNi0.8Co0.1Mn0.1O2正极材料为典型的α-NaFeO2层状结构,无杂质峰;从SEM像可以看出,产物颗粒为类球形,分散性好,由一次粒子紧密堆积而成,平均粒径为3 μm;电化学测试结果表明,在2.8～4.3 V电压范围内,750℃焙烧15h合成的LiNi0.8Co0.1Mn0.1O2材料的电化学性能最优,0.1C时,其首次放电容量为186.748mA·h/g,分别高于700和800℃时的首次放电容量172.947和180.235mA·h/g.材料在0.5和2C时循环40次后,容量保持率分别为98.32％和88.72％,循环性能良好.     

锂离子电池Li（Ni3／8Co3／8Mn2／8）O2层状正极材料的制备与电化学性能

采用液相共沉淀方法合成锂离子电池用Li(Ni3/8Co3/8Mn2/8)O2正极材料,以XRD、SEM、原子吸收光谱法和电池充放电循环测试方法表征Li(Ni3/8Co3/8Mn2/8)O2粉末的结构和性能.结果表明:900℃焙烧10 h合成的Li(Ni3/8Co3/8Mn2/8)O2粉末样品具有较好的综合电化学性能和良好的六角层状结构,阳离子混合度小,六角晶格有序性高,颗粒为由小晶粒结合而成的多晶体,平均粒径约为4.5 μm,I003/I104为1.25,R值为0.48,首次放电容量为172.9 mA·h/g(2.8～4.5 V,0.1C倍率),0.2C倍率循环20次后电容量为首次循环放电容量的96.1%.     

锂离子电池正极材料LiNi1/3Co1/3Mn1/3O2的制备及性能研究

采用溶胶-凝胶法制备了锂离子电池正极材料LiNi1/3Co1/3Mn1/3O2,并考察了烧结温度对材料结构、表面形貌和电化学性能的影响.XRD和SEM测试结果表明,900℃下烧结得到的样品是粒径在0.3～0.5 μm范围的球形粒子,具有最佳的阳离子有序度;充放电测试结果表明,其在0.1C倍率下首次放电容量达到148.8...     

静电纺丝法制备NiO-ZnO纳米纤维及其电化学性能研究

通过静电纺丝法制备NiO-ZnO复合氧化物纳米纤维,利用XRD、XPS、BET、SEM、TEM和电化学工作站等对材料的结构、成分、形貌和电化学性能进行表征。结果发现当镍与锌质量比为10:1时,NiO-ZnO复合氧化物纳米纤维具有大比表面积71.425 m~2/g,表面占主导地位的介孔直径约为13.37 nm。在电化学测试中,该样品呈现出清晰的氧化还原峰,在1 A/g的电流密度下,放电比电容量为441 F/g,这远高于纯Ni O纤维的331 F/g,循环1000次电容保持率达到81.2%,也远大于纯NiO纤维的70.4%。当电流密度为0.5 A/g时,比电容量最大可达到461 F/g,表现出优良的充放电性能。     

不同金属离子价态的前驱体制备球形LiNi1/3Mn1/3Co1/3O2的性能比较

利用共沉淀法和控制结晶氧化法在不同条件下分别制备出低价态球形Ni1/3Co1/3Mn1/3(OH)2和高价态球形Ni1/3Co1/3Mn1/3OOH前驱体,并分别和LiOH·H2O在不同温度烧结合成出球形锂离子正极材料Li(Ni1/3Co1/3Mn1/3)O2.XPS分析表明,制备的高价态球形Ni1/3Co1/3Mn1/3OOH前驱体其过渡金属Ni、Co和Mn的价态分别是2+,3+,4+,XRD分析表明,高价态球形Ni1/3Co1/3Mn1/3OOH前驱体比低价态球形Ni1/3Co1/3Mn1/3(OH)2前驱体具有较高的活性,能够在低温下合成出Li(Ni1/3Co1/3Mn1/3)O2,而且制备的产物结晶度高,阳离子混排程度小,具有规整的层状a-NaFeO2结构.充放电实验表明,由高价态球形Ni1/3Co1/3Mn1/3OOH前驱体制备的Li(Ni1/3Col/3Mn1/3)O2具有优良的充放电性能和循环性能.     

Si4+和F-掺杂对LiNi1/3Co1/3Mn1/3O2结构和电化学性能的影响

以Li2CO3、NiO、Co2O3、MnO2、LiF和SiO2为原料,采用机械力活化固相法制备了Si4+和F-掺杂的锂离子电池正极材料LiNi1/3Co 1/3Mn1/3O2.通过X射线衍射(XRD)、扫描电镜(SEM)和电化学性能测试等技术研究了LiNi1/3Co1/3Mn1/3O2的结构特征、形貌及电化学性能等.结...     

初始Li/(Mn+Ni)摩尔比对LiNi0.5Mn0.5O2电化学性能的影响

以Li2CO3,MnCO3和Ni(OH)2为原料,采用一步固相反应制备锂离子电池层状结构正极材料LiNi0.5-Mn0.5O2,采用X射线衍射和扫描电镜对其结构和形貌进行表征,并研究配料时不同初始Li/(Mn Ni)摩尔比(1.0,1.05,1.1,1.2,1.5)对LiNi0.5Mn0.5O2电化学性能的影响。X射线衍射结果表明,在600℃预烧12 h而后800℃烧结24 h的条件下各样品结晶完整,初始Li/(Mn Ni)摩尔比为1.5时样品有未知相杂质生成。扫描电镜分析表明,随着初始Li/(Mn Ni)摩尔比的增大,颗粒团聚加剧。电化学测试结果表明,随着初始Li/(Mn Ni)摩尔比(≥1.05)的提高,初始容量有下降趋势。初始Li/(Mn Ni)摩尔比为1.05和1.1时样品首次放电容量分别为167.0 mA.h/g和147.2 mA.h/g,循环20次后容量保持率分别为88.2%和97.8%。     

合成方法对LiNi0．4Co0．2Mn0．4O2电化学性能的影响

分别采用混合氢氧化物法和溶胶．凝胶法制备了三元的锂离子电池LiNi0．4Co0．2Mn0．4O2正极材料。采用XRD，SEM以及BET等方法对正极材料进行表征，并对其电化学性能进行测试。实验结果表明，不同的合成方法和工艺条件导致了材料的晶相结构、表观形貌、比表面积以及电化学性能上的差异。LiNi0．4Co0．2Mn0．4O2正极材料中出现的阳离子相互占位将导致其电化学性能变差。与溶胶．凝胶法制备的样品相比，混合氢氧化物法制备的样品具有较高的比表面积（3．2m2／g）和较高的放电比容量。在充放电电压范围为2．5～4．3V、充放电电流为20mA／g条件下，混合氢氧化物法所制备样品的首次放电比容量为180．1mAh·g^-1，20次循环后放电容量为160．2mAh·g^-1，并显示出较好的循环稳定性。     

控制结晶法合成球形正极材料LiNi0.8Co0.2O2及其电化学性能

采用控制结晶法制备锂离子电池用高密度球形正极材料LiNi0.8Co0.2O2。对前驱体Ni0.8Co0.2(OH)2制备工艺进行优化,在金属盐溶液流速为8 mL/min,搅拌速率450 r/min,pH值为11.5,氨浓度20 g/L反应36 h的条件下,合成了振实密度为2.02 g/cm3的球形Ni0.8Co0.2(OH)2。并以Ni0.8Co0.2(OH)2为原料,与LiOH.H2O进行混合研磨进行高温烧结,考察烧结制度对合成材料LiNi0.8Co0.2O2电化学性能的影响。在Li/(Ni Co)配比为1.05、氧气流量为800 mL/min,750℃下烧结16 h所得材料LiNi0.8Co0.2O2电化学性能最优:在0.2 C,3.0~4.3 V的条件下,首次放电容量达到195.4 mA.h/g,循环50次后容量保持率达到89.2%。     

微波热解法制备的炭涂层对LiNi_（1／3）Mn_（1／3）Co_（1/3）O_2性能的影响

报道了炭包覆锂离子电池正极材料LiNi_（1／3）Mn_（1／3）Co_（1/3）O_2的新工艺。炭涂层由前驱体葡萄糖通过微波热解而形成。采用x射线粉末衍射（XRD）、扫描电镜、x射线荧光测试和恒流充放电测试来表征所制备的材料。XRD结果表明,炭包覆没有改变LiNi_（1／3）Mn_（1／3）Co_（1/3）O_2材料的相结构。SEM结果表明,炭包覆的LiNit／3Mnl／3Col／302颗粒表面变得粗糙。充放电测试结果显示,炭包覆的LiNi_（1／3）Mn_（1／3）Co_（1/3）O_2的循环性能与未包覆的相比得到提高。炭包覆的LiNi_（1／3）Mn_（1／3）Co_（1/3）O_2在0．2C倍率下循环50次的容量保持率由84．8％提升到95．5％,且高倍率下材料的容量保持率得到提高。     

Zn掺杂对LiNi_(1/3)Co_(1/3)Mn_(1/3)O_2结构与电化学性能的影响

用溶胶凝胶法制备了Li Ni1/3Co1/3-x Mn1/3Znx O2(x=0,1/24,2/24,4/24)锂离子电池正极材料。由X射线衍射和扫描电镜对其分析结果表明,Zn掺杂不改变Li Ni1/3Co1/3Mn1/3O2的α-Na Fe O2层状结构,当掺杂量达到4/24时,杂相产生。电化学研究表明,当Zn掺杂量为2/24时,Li Ni1/3Co1/3Mn1/3O2首次放电容量由未掺杂的169.2 m Ah·g-1降低为160.1m Ah·g-1,但循环性能明显提高,30次循环后的容量保持率由未掺杂的89.2%升至97%。并且在20、40、60和80 m A·g-1不同的电流密度下继续循环20次后,当再次恢复到20 m A·g-1的电流密度时,放电容量可恢复到150.3 m Ah·g-1。     

Surface composition and electrochemical behavior of LiNi1/3Co1/3Mn1/3O2 cathode material with copper additive

LiNi_1/3Co_1/3Mn_1/3O₂（NCM） cathode material containing copper was prepared by co-precipitation method.The material was characterized by X-ray photoelectron spectroscopy（XPS） and galvanostatic cycling.XPS data indicate that surface compositions of the samples containing copper are different from the bare NCM.Copper on surface of particles was enriched,while nickel and lithium content was reduced.The electrochemical performance of NCM was affected by the change of surface compositions.Cycling performance charged to the cutoff voltage of 4.6 V was improved by introducing copper into the material.The effects of copper content on electrochemical behaviors of NCM at 4.5 V were discussed.     

Synthesis of LiNi1/3CO1/3Mn1/3O2 cathode material via oxalate precursor

Using oxalic acid and stoichiometrically mixed solution of NiCl2, CoCl2, and MnCl2 as starting materials, the triple oxalate precursor of nickel, cobalt, and manganese was synthesized by liquid-phase co-precipitation method. And then the LiNi1/3Co1/3Mn1/3O2 cathode materials for Li-ion battery were prepared from the precursor and LiOH-H2O by solid-state reaction. The precursor and LiNi1/3Co1/3Mn1/3O2 were characterized by chemical analysis, XRD, EDX, SEM and TG-DTA. The results show that the composition of precursor is Ni1/3Co1/3Mn1/3C2O4·2H2O. The product LiNi1/3Co1/3Mn1/3O2, in which nickel, cobalt and manganese are uniformly distributed, is well crystallized with a-NaFeO2 layered structure. Sintering temperature has a remarkable influence on the electrochemical performance of obtained samples. LiNi1/3Co1/3Mn1/3O2 synthesized at 900 ℃ has the best electrochemical properties. At 0.1C rate, its first specific discharge capacity is 159.7 mA·h/g in the voltage range of 2.75-4.30 V and 196.9 mA·h/g in the voltage range of 2.75-4.50 V; at 2C rate, its specific discharge capacity is 121.8 mA·h/g and still 119.7 mA·h/g after 40 cycles. The capacity retention ratio is 98.27%.     

Effects of Na+ doping on crystalline structure and electrochemical performances of LiNi0.5Mn1.5O4 cathode material

Pristine LiNi_0.5Mn_1.5O₄ and Na-doped Li_0.95Na_0.05Ni_0.5Mn_1.5O₄ cathode materials were synthesized by a simple solid-state method. The effects of Na⁺ doping on the crystalline structure and electrochemical performance of LiNi_0.5Mn_1.5O₄ cathode material were systematically investigated. The samples were characterized by XRD, SEM, FT-IR, CV, EIS and galvanostatic charge/discharge tests. It is found that both pristine and Na-doped samples exhibit secondary agglomerates composed of well-defined octahedral primary particle, but Na⁺ doping decreases the primary particle size to certain extent. Na⁺ doping can effectively inhibit the formation of Li_xNi_1–xO impurity phase, enhance the Ni/Mn disordering degree, decrease the charge-transfer resistance and accelerate the lithium ion diffusion, which are conductive to the rate capability. However, the doped Na⁺ ions tend to occupy 8a Li sites, which forces equal amounts of Li⁺ ions to occupy 16d octahedral sites, making the spinel framework less stable, therefore the cycling stability is not improved obviously after Na⁺ doping.     

Preparation of LiNi1/3Co1/3Mn1/3O2 cathode materials from spent Li-ion batteries

A recycling process including separation of electrode materials by ultrasonic treatment, acid leaching, Fe-removing, precipitation of cobalt, nickel, manganese and lithium has been applied successfully to recycle spent lithium-ion batteries and to synthesize LiNi1/3Co1/3Mn1/3O2. When ultrasonic treatment with 2-nitroso-4-methylphenol（NMP） at 40 ℃ for 15 min, the electrode materials are separated completely. Above 99% of Co, Ni, Mn and Li, 95% of Fe in the separated electrodes are acid-leached in the optimized conditions of 2 mol/L H2SO4, 1：2 H2O2：H2SO4 （molar ratio）, 70 ℃, 1：10 initial S：L ratio, and l h. 99.5% of Fe and less than 1% of Co, Ni, Mn in the leaching solution can be removed in the conditions of initial pH value 2.0-2.5 adjusted by adding 18% Na2CO3, 90 ℃ and stirring time 3 h. After adjusted to be equal by adding NiSO4, COSO4 and MnSO4 solution, 97.1% of Ni, Co, Mn in the Fe-removing surplus leaching solution can be recovered as Ni1/3Co1/3Mn1/3（OH）2. 94.5% of Li in the surplus filtrate after the deposition of Co, Ni and Mn can be recovered as LiECO3. The LiNi1/3Co1/3Mnl/3O2, prepared from the recovered compounds, is found to have good characteristics of the layered structure and elecrtochemical performance.     

Effects of synthesis conditions on the structural and electrochemical properties of layered LiNi1/3Co1/3Mn1/3O2 cathode material via oxalate co-precipitation method

The uniform layered LiNi1/3Co1/3Mn1/3O2 cathode material for lithium ion batteries was prepared by using (Ni1/3Co1/3Mn1/3)C2O4 as precursor synthesized via oxalate co-precipitation method in air. The effects of calcination temperature and time on the structure and electrochemical properties of the LiNi1/3Co1/3Mn1/3O2 were systemically studied. XRD results revealed that the optimal calcination conditions to prepare the layered LiNi1/3Co1/3Mn1/3O2 were 950°C for 15 h. Electrochemical measurement showed that the sample prepared under the such conditions has the highest initial discharge capacity of 160.8 mAh/g and the smallest irreversible capacity loss of 13.5% as well as stable cycling performance at a constant current density of 30 mA/g between 2.5 and 4.3 V versus Li at room temperature.     

锂离子电池正极材料LiNi_1/3Co_1/3Mn_1/3O_2的研究进展

介绍了一种新型的锂离子电池正极材料LiNi1/3Co1／3Mn1／3O2的最新研究状况,描述了材料的晶体及电子结构,以及电化学性能;重点总结了现今国内外制备此材料的几种主要合成方法及研究进展;同时,介绍了不同掺杂元素（Fe、B、Al、Ti）对材料的改性作用。