On the growth mechanism of single-walled carbon nanotubes by catalytic carbon vapor deposition on supported metal catalysts

A comprehensive kinetic study was performed to throw light on the formation mechanism of single walled carbon nanotubes (SWNTs) in chemical vapor deposition processes. SWNTs were synthesized by catalytic decomposition of methane or ethylene on supported transition metal catalysts. Kinetic curves (the amount of SWNT as a function of time) were obtained as a function of the nature and the preparation of the supported catalysts, temperature, the fluxes of the gases (the reagent hydrocarbon and the carrying gas), and the partial pressure of the hydrocarbon. The final products were characterized by transmission electron microscopy, Raman spectroscopy, chemical analysis, and thermogravimetric measurements. The fundamental factors determining the SWNT formation are discussed in detail, taking into consideration several observations from the literature as well.     

用于制备优质单壁碳纳米管管束的MgO负载Fe3O4纳米粒子的合成

采用沉淀方法制备了直径分布狭窄的均匀Fe3O4纳米颗粒.Fe3O4纳粒形体几近一致,平均粒径为10.33 nm±2.99 nm(平均粒径±标准偏差).在超声作用下将MgO纳米颗粒分散在一定量Fe3O4纳米颗粒的水溶液中获得MgO负载Fe3O4的纳米颗粒.以甲烷为碳源,Fe3O4/MgO为催化剂,经化学气相沉积,在Fe3O4纳粒上制得了大量直径近乎均匀的单壁碳纳米管(SWCNTs)束.TEM显示:SWCNTs的平均直径1.22rm.热重分析显示:样品在400℃～600℃温度区间失重量约19％.拉曼光谱显示:SWCNTs的ID/IG的强度比为0.03,表明采用Fe3O4/MgO催化剂可制得高石墨化程度的单壁碳纳米管.     

高分散度非晶态NiB／CNTs催化剂制备及其催化加氢性能

利用苯胺、曲拉通分别对氨气热处理的碳纳米管进一步功能化，修饰碳纳米管表面，促进碳纳米管分散。采用超声波辅助的浸渍-化学还原法制备非晶态NiB／CNTs合金催化剂，平均粒径为14nm、10nm的非晶态NiB颗粒均匀分布在苯胺、曲拉通处理的碳纳米管表面。苯胺、曲拉通功能化处理使催化剂的Ni负载量分别提高了10．4％、14．6％，同时提高了催化剂的乙炔加氢活性和乙烯选择性。将苯胺和曲拉通的处理效果比较，发现无论是NiB颗粒的分散度还是催化剂的加氢性能，曲拉通处理的效果明显优于苯胺。     

Preparation of ceria nanoparticles supported on carbon nanotubes

By chemical reaction of CeCl₃ and NaOH on carbon nanotube solution and subsequent heat treatment, ceria nanoparticles supported on carbon nanotubes were prepared. The processing parameters affecting the size of ceria particles were discussed. The particles were characterized by XRD and TEM. XRD patterns revealed that the particles exhibited CaF₂-type crystal structure. The TEM micrograph showed that the mean sizes of ceria particles were about 6 nm.     

Pt, Rh and Pt-Rh nanoparticles on modified single-walled carbon nanotubes for hydrogenation of benzene at room temperature

Nanometer-sized Pt, Rh, and bimetallic Pt-Rh particles can be deposited on surface of phenylacetic acid functionalized single-walled carbon nanotubes (SWCNTs) by a microemulsion method. The SWCNT-supported metallic nanoparticles show much greater catalytic activities compared with commercially available carbon-supported Pt and Rh catalysts for hydrogenation of neat benzene under mild experimental conditions. The bimetallic Pt-Rh nanoparticle catalyst synthesized by this method shows an enhanced activity relative to individual SWCNT-supported Pt and Rh nanoparticle catalysts. The SWCNT-supported metal nanoparticle catalysts can be recycled and reused at least five times without losing their activity. The hydrogenation reactions performed under our experimental conditions would not affect the pi-pi stacking holding phenylacetic acid on SWCNT surface.     

多壁碳纳米管负载镁掺杂氧化锌纳米颗粒的研究

利用醋酸锌和醋酸镁为原料,无水乙醇为溶剂,草酸为沉淀剂,通过共沉淀法和后续热处理实现多壁碳纳米管表面负载镁掺杂氧化锌纳米颗粒,并使用X射线衍射仪、扫描电子显微镜、透射电子显微镜和紫外吸收光度计研究复合材料的形貌和光学性能。电子显微镜结果表明,在450℃热处理下,多壁碳纳米管表面能够均匀地负载镁掺杂氧化锌纳米颗粒,其颗粒粒径大约为10～20nm。紫外吸收光谱结果说明,镁掺杂显著地提高多壁碳纳米管/氧化锌复合材料的紫外吸收性能,而且其紫外吸收峰向短波方向蓝移达22nm。     

Oxygen reduction activity of carbon nitride supported on carbon nanotubes

Fuel cells offer an alternative to burning fossil fuels, but use platinum as a catalyst which is expensive and scarce. Cheap, alternative catalysts could enable fuel cells to become serious contenders in the green energy sector. One promising class of catalyst for electrochemical oxygen reduction is iron-containing, nanostructured, nitrogen-doped carbon. The catalytic activity of such N-doped carbons has improved vastly over the years bringing industrial applications ever closer. Stoichiometric carbon nitride powder has only been observed in recent years. It has nitrogen content up to 57% and as such is an extremely interesting material to work with. The electrochemical activity of carbon nitride has already been explored, confirming that iron is not a necessary ingredient for 4-electron oxygen reduction. Here, we synthesize carbon nitride on a carbon nanotube support and subject it to high temperature treatment in an effort to increase the surface area and conductivity. The results lend insight into the mechanism of oxygen reduction and show the potential for carbon nanotube-supported carbon nitride to be used as a catalyst to replace platinum in fuel cells.     

Fabrication of PtNi bimetallic nanoparticles supported on multi-walled carbon nanotubes

Platinum/nickel bimetallic nanoparticles supported on multi-walled carbon nanotubes (xPtNi/CNTs) were synthesised. The fabrication process includes the chemical modification on the graphene surface of CNTs by acid treatment and the subsequent deposition of Pt or PtNi bimetallic nanoparticles with different compositions of Pt (x = 100, 90, 80 and 70 wt%). The deposition was carried out using ethylene glycol as a reducing agent in the polyol method or using poly(amidoamine) dendrimer as a platform and sodium borohydride as a reducing agent to load the metal nanoparticles on the CNT surface. The structures of the produced PtNi/CNT nanoparticles were investigated by ultraviolet absorption spectra, X-ray diffraction (XRD) and the composite ratio consisting of 70 wt% of metal content and 30 wt% of CNTs was confirmed by the thermogravimetric analysis. The morphology and the phase identification of the produced PtNi/CNT nanoparticles were investigated by high-resolution scanning electron microscope, transmission electron microscope and XRD measurements. It was observed that the deposited Pt and PtNi bimetallic nanoparticles on the surface of CNTs had average particle sizes of 2–16 nm, when they were prepared from the polyol method. On the other hand, the PtNi/CNT nanoparticles prepared by using a dendrimer as an intermediate had a smaller particle size and more uniform size distribution of the quantum dot size ranged from 2 to 4 nm.     

Facile synthesis of Au nanoparticles supported on polyphosphazene functionalized carbon nanotubes for catalytic reduction of 4-nitrophenol

Carbon nanotubes (CNTs) functionalized with cyclotriphosphazene-containing polyphosphazenes (PZS) were found to cause the facile immobilization of Au nanoparticles on the surface. The PZS functional layers not only improved the dispersion of CNTs in aqueous solution but also used as a platform for subsequent immobilization of Au nanoparticles. The functionalized CNTs and the Au@PZS@CNTs nanohybrids were characterized by scanning electron microscopy, transmission electron microscopy, energy-dispersive X-ray spectroscopy, Fourier transform infrared spectrometer, X-ray diffraction, thermogravimetric analysis, Atomic absorption spectrum, and X-ray photoelectron spectroscopy. The results showed that the PZS layers with thickness of about 25 nm were formed uniformly on CNT surfaces by polycondensation between hexachlorocyclotriphosphazene and 4,4′-sulfonyldiphenol, and that high density of homogeneously dispersed spherical Au nanoparticles with average size of 6 nm was immobilized on their outer surface. Meanwhile, the catalytic activity and reusability of the Au@PZS@CNTs nanohybrids were investigated by employing the reduction of 4-nitrophenol into 4-aminophenol by NaBH₄ as a model reaction.     

Cutting single-walled carbon nanotubes

A two-step process is utilized for cutting single-walled carbon nanotubes (SWNTs). The first step requires the breakage of carbon-carbon bonds in the lattice while the second step is aimed at etching at these damage sites to create short, cut nanotubes. To achieve monodisperse lengths from any cutting strategy requires control of both steps. Room-temperature piranha and ammonium persulfate solutions have shown the ability to exploit the damage sites and etch SWNTs in a controlled manner. Despite the aggressive nature of these oxidizing solutions, the etch rate for SWNTs is relatively slow and almost no new sidewall damage is introduced. Carbon-carbon bond breakage can be introduced through fluorination to ～C(2)F, and subsequent etching using piranha solutions has been shown to be very effective in cutting nanotubes. The final average length of the nanotubes is approximately?100?nm with carbon yields as high as 70-80%.     

Moderate temperature synthesis of single-walled carbon nanotubes on alumina supported nickel oxide catalyst

A simple nickel oxide catalyst has been developed in synthesizing single-walled carbon nanotubes (SWNTs) at moderate temperature. The catalyst used in the experiment was without a preceding reduction in hydrogen flow. The synthesis of SWNTs was performed at a temperature of 700 °C, which represents a moderate reaction temperature. The presence of SWNTs on the catalyst was confirmed by transmission electron microscope (TEM) and Raman spectroscope. The Raman spectrum shows a strong intensity at the radial breathing mode, indicating that the occurrence of SWNTs was dominant. Raman data further reveals that the synthesized SWNTs had the diameters in the range from 0.58 to 2.02 nm.     

载铜多壁碳纳米管的抗菌活性研究

采用溶胶-凝胶法在多壁碳纳米管(MWCNTs)表面负载纳米铜,制备复合抗菌材料MWCNTsCu。X射线能量色散谱(EDS)、透射电子显微镜(TEM)表征结果表明,纳米铜成功地负载在MWCNTs表面,纳米铜分散良好。以大肠杆菌为目标,评价了MWCNTs-Cu对水中细菌的抗菌活性,探讨了其抗菌机理。研究结果表明,MWCNTs-Cu对大肠杆菌表现出很强的抗菌性,其中,MWCNTs对大肠杆菌有强吸附性,纳米铜起主要杀菌作用。     

纳米碳颗粒负载碳化钼复合物的制备及其催化性能研究

利用爆炸辅助的化学气相沉积法成功地制备了纳米碳颗粒负载碳化钼的复合物,并利用TEM和XRD对合成纳米复合物的形貌和结构进行了表征;以环己烷脱氢反应为探针对其催化性能进行了评价,考察了钼含量对碳化钼复合物催化性能的影响.结果表明,纳米碳颗粒由有序度较低的石墨片层组成,形貌近似球形,粒度分布均匀,大小约为20nm,原位修饰的六方碳化钼分散在碳颗粒表面;钼含量不同,复合物对环己烷脱氢催化性能有较大差异,当钼含量为15%时,催化性能最好.     

Three dimensional single-walled carbon nanotubes

We report a simple fabrication method of creating a three-dimensional single-walled carbon nanotube (CNT) architecture in which suspended CNTs are aligned parallel to each other along the conventionally unused third dimension at lithographically defined locations. Combining top-down lithography with the bottom-up block copolymer self-assembly technique and utilizing the excellent film forming capability of polymeric materials, highly uniform catalyst nanoparticles with an average size of 2.0 nm have been deposited on sidewalls for generating CNTs with 1 nm diameter. This three-dimensional platform is useful for fundamental studies as well as technological exploration. The fabrication method described herein is applicable for the synthesis of other very small 1D nanomaterials using the catalytic vapor deposition technique.     

Optically active single-walled carbon nanotubes

The optical, electrical and mechanical properties of single-walled carbon nanotubes (SWNTs) are largely determined by their structures, and bulk availability of uniform materials is vital for extending their technological applications. Since they were first prepared, much effort has been directed toward selective synthesis and separation of SWNTs with specific structures. As-prepared samples of chiral SWNTs contain equal amounts of left- and right-handed helical structures, but little attention has been paid to the separation of these non-superimposable mirror image forms, known as optical isomers. Here, we show that optically active SWNT samples can be obtained by preferentially extracting either right- or left-handed SWNTs from a commercial sample. Chiral 'gable-type' diporphyrin molecules bind with different affinities to the left- and right-handed helical nanotube isomers to form complexes with unequal stabilities that can be readily separated. Significantly, the diporphyrins can be liberated from the complexes afterwards, to provide optically enriched SWNTs.     

Formylation of single-walled carbon nanotubes

We report an improved, elegant method for the covalent formylation of single-wall carbon nanotubes (SWNTs) via formyl transfer from N-formylpiperidine, which could potentially open the gateway for more versatile chemical modification of carbon nanotube (CNT) walls than is possible via other reported functionalisation methods. The formylation reaction does not inflict damage upon the pristine CNT structure, unlike the currently commonly used carboxylation route, and involves much fewer steps, and takes considerably less time, than most other reported routes. The modified SWNTs have been characterised by Raman spectroscopy, ultraviolet-visible-near infrared (UV-vis-NIR) spectroscopy and "covalent tagging" with derivatising groups followed by thermogravimetric analysis-mass spectroscopy (TGA-MS). UV-vis-NIR spectroscopy shows that there is only limited disruption of the intrinsic electronic structure of the SWNTs. This is confirmed from estimates of the extent of functionalisation from TGA-MS, which suggest that it may be as low as 2 atomic per cent.     

Charge-transfer interaction in single-walled carbon nanotubes with tetrathiafulvalene and their applications

We observed that single-walled carbon nanotube (SWNT) was aligned in the presence of TTF This alignment was induced by a specific interaction between SWNT and tetrathiafulvalene (TTF), a well-known organic donor. The interaction between the two molecules can be explained by a charge-transfer, which was confirmed by X-ray photoelectron spectroscopy (XPS) and Raman spectroscopy. The binding energies of S (2P1/2) and S (2P3/2) were shifted from 163.0 eV and 164.1 eV to 163.9 eV and 165.1 eV, respectively. In Raman spectra of the SWNT-TTF, three peaks of SWNT in radial breathing mode were also upshifted by 4-5 cm(-1). The charge-transfer interaction also contributed in modifying the electronic structure of SWNT and furthermore enhanced the electrical conductivity of SWNT. A more conductive thin film was fabricated using the SWNT-TTF Four-probe measurement revealed that the surface resistance of the SWNT-TTF film was reduced to 4.359 omega at room temperature while that of SWNT film was 6.894 omega. These results enable carbon nanotubes to be utilized more for practically for industrial applications in fabricating peculiar nano-sized building blocks.     

Purification of single-walled carbon nanotubes

The discovery of carbon nanotubes (CNTs) created much excitement and stimulated extensive research into the properties of nanometer-scale cylindrical networks. From then on, various methods for the synthesis and characterization of aligned CNTs-both single-walled (SWCNTs) and multi-walled (MWCNTs) by different methods have been hotly pursued. Unfortunately, most methods currently in use produce raw multi component solid products, only a small fraction of which contains carbon nanotubes. The balance of the material is composed of residual catalyst particles (some of which are encased in concentric graphitic shells), fullerenes, other graphitic materials and amorphous carbon. These impurities cause a serious impediment for their detailed characterization and applications. If the carbon nanotube is ever to fulfill its promise as an engineering material, large, high quality aliquots will be required. A number of purification methods involving elimination processes such as physical separation, gas phase and liquid phase oxidation in combination with chemical treatments have been developed for nanotube materials. Though the quantitative determination of purity remains controversial, reported yields are best regarded with an appropriate level of skepticism on the method of assay. In this article, a review is given on the past and recent advances in purification of SWCNTs.     

Individual Fe-Co alloy nanoparticles on carbon nanotubes: structural and catalytic properties

We report the synthesis, characterization, and catalytic performance of Fe-Co alloy nanoparticles inside the tubular channel of carbon nanotubes. The homogeneous distributions of Fe and Co in the isolated nanoparticles were evidenced confidentially by bulk and surface structural and compositional characterizations, that is, scanning electron microscopy, high-resolution transmission electron microscope in combination with elemental mapping by energy dispersive X-ray spectroscopy and electron energy-loss spectroscopy, powder X-ray diffraction, and X-ray photoelectron spectroscopy. We also demonstrate for the first time an unusual synergism in alloy catalysis. The alloy nanoparticles with widely varying Co/Fe ratio are kept as active as Co for the H 2 production from NH 3 decomposition. The stability of Co was significantly improved by alloying with Fe. We expect our experimental method to be a general approach to elucidate the synergism phenomenon in alloy catalysis.     

Preparation and catalytic activity of nanostructured Pd catalysts supported on hydrogenotitanate nanotubes

Nanostructured palladium particles (nanorods, icosahedra, cubes) were synthesized in aqueous solution using a seeding-mediated approach with a structure-directing agent. These nanostructured Pd particles were then impregnated onto hydrogenotitanate nanotubes using two different impregnation procedures. The as-prepared catalysts were then tested in the selective hydrogenation of cinnamaldehyde at 323 K under 10 bars of H₂. The selectivity is influenced by the morphology of the Pd nanostructured particles with a higher selectivity into saturated alcohols when the proportion of (111) Pd sites increases.