Growth and spectral properties of Cr:KAl(MoO4)2 crystal

The Cr³⁺:KAl(MoO₄)₂ single crystal was grown by top seeding solution growth method (TSSG). Based on the absorption and emission spectra, the crystal field strength Dq, the Racah parameters B and C, the effective phonon energy ?ω and the Huang-Rhys factor S were calculated: Dq = 1494.8 cm^− 1, B = 585.5 cm^− 1 and C = 3049 cm^− 1, ?ω = 373.8 cm^− 1 and the Huang-Rhys factor S = 3.74, respectively. The value Dq/B = 2.55 indicates that Cr³⁺ ion occupies the strong crystal field site in KAl(MoO₄)₂ crystal. A comparison of crystal field parameters for Cr³⁺:KAl(MoO₄)₂ with other Cr³⁺-doped crystals was presented. The results of spectral measurement show that Cr³⁺:KAl(MoO₄)₂ may be a potential candidate for broadband laser applications.     

Polarized spectral properties of Tm:K5Bi(MoO4)4 crystal

Trivalent thulium-doped K₅Bi(MoO₄)₄ single crystals were grown by the Czochralski method. Its polarized absorption and fluorescence spectra and fluorescence decay curves were recorded at room temperature. On the basis of the Judd-Ofelt theory, the spectral parameters of the Tm³⁺:K₅Bi(MoO₄)₄ crystal were calculated. The cross relaxations between Tm³⁺ ions were analyzed. The emission cross sections of the ³F₄ → ³H₆ transition were obtained by the Fuchtbauer-Ladenburg formula and then the gain cross sections around 1.9 μm were calculated. The peak emission cross section and width of emission band around 1.9 μm are comparable to those for Tm³⁺:YAG and the tunable range is about 280 nm for the potential ∼1.9 μm laser operation via the ³F₄ → ³H₆ transition.     

Influence of excitation wavelengths on luminescent properties of Sr3Al2O6:Eu, Dy phosphors prepared by sol-gel-combustion processing

Eu²⁺ and Dy³⁺ ion co-doped Sr₃Al₂O₆ red-emitting long afterglow phosphor was synthesized by sol-gel-combustion methods using Sr(NO₃)₂, Al(NO₃)₃·9H₂O, Eu₂O₃, Dy₂O₃, H₃BO₃ and C₆H₈O₇·H₂O as raw materials. The crystalline structure of the phosphors were characterized by X-ray diffraction, luminescent properties of phosphors were analyzed by fluorescence spectrophotometer. The effect of excitation wavelengths on the luminescent properties of Sr₃Al₂O₆:Eu²⁺, Dy³⁺ phosphors was discussed. The emission peak of Sr₃Al₂O₆:Eu²⁺, Dy³⁺ phosphor lays at 516 nm under the excitation of 360 nm, and at 612 nm under the excitation of 468 nm. The results reveal that the Sr₃Al₂O₆:Eu²⁺, Dy³⁺ phosphor will emit a yellow-green light upon UV illumination, and a bright red light upon visible light illumination. The emission mechanism was discussed according to the effect of nephelauxetic and crystal field on the 4f⁶5d¹ → 4f⁷ transition of the Eu²⁺ ions in Sr₃Al₂O₆. The afterglow time of (Sr_0.94Eu_0.03Dy_0.03)₃ Al₂O₆ phosphors lasts for over 600s after the excited source was cut off.     

Novel blue-emitting phosphor NaMg4(PO4)3:Eu, Ce with energy transfer

A blue-emitting phosphor of NaMg₄(PO₄)₃:Eu²⁺, Ce³⁺ was prepared by a combustion-assisted synthesis method. The phase formation was confirmed by X-ray powder diffraction measurement. Photoluminescence excitation spectrum measurements show that the phosphor can be excited by near UV light from 230 to 400 nm and presents a dominant luminescence band centered at 424 nm due to the 4f⁶5d¹ → 4f⁷ transition of Eu²⁺ ions at room temperature. Effective energy transfer occurs in Ce³⁺/Eu²⁺ co-doped NaMg₄(PO₄)₃ due to large spectral overlap between the emission of Ce³⁺ and excitation of Eu²⁺. Co-doping of Ce³⁺ enhances the emission intensity of Eu²⁺ greatly by transferring its excitation energy to Eu²⁺, and Ce³⁺ plays a role as a sensitizer. Ce³⁺-Eu²⁺ co-doped NaMg₄(PO₄)₃ powders can possibly be applied as blue phosphors in the fields of lighting and display.     

Synthesis and luminescent characteristic of Eu-doped (Gd,Lu)2O3 nanopowders

Eu³⁺ doped (Gd,Lu)₂O₃ nanopowders with particle sizes ranging from 20 to 70 nm were synthesized by the co-precipitant method using mixed precipitants, namely the mixture of ammonium hydroxide (NH₃⋅H₂O) and ammonium hydrogen carbonate (NH₄HCO₃). The precipitate precursor prepared by this method was believed to possess a basic carbonate composition and its thermal decomposition of the (Gd,Lu)₂O₃:Eu³⁺ powders were investigated by Thermogravimetric analysis and differential thermal analysis (TG-DTA). This preparation was followed by a calcination process at 800-1100 °C and corresponding phosphor structure were examined by X-ray diffraction (XRD) and transmission electron microscopy (TEM). Photoluminescence measurement of the (Gd,Lu)₂O₃:Eu³⁺ particles show typical red emission at the 612 nm corresponding to the ⁵D₀ → ⁷F₂ transition. We found that the optimal Eu³⁺ molar doping concentration, calcined temperature and reaction time were 7 mol%, 1000 °C, and 2 h, respectively, which is helpful to obtain the final transparent ceramics with excellent properties.     

Polarized spectroscopic properties of Ho ions in NaLa(MoO4)2 crystal

A Ho³⁺-doped NaLa(MoO₄)₂ single crystal was grown by the Czochralski method. The polarized absorption spectra, polarized fluorescence spectra, and fluorescence decay curves of the crystal were measured at room temperature. The spontaneous emission probabilities, radiative lifetimes, and fluorescence branching ratios of the typical fluorescence multiplets of Ho³⁺ ions were calculated. The polarized stimulated emission and gain cross-sections of the ⁵I₇ → ⁵I₈ transition were obtained. The results show that the Ho³⁺:NaLa(MoO₄)₂ crystal is a promising gain medium for tunable and ultrashort pulse lasers operating around 2.0 μm.     

Effects of Zn doping on the structural and luminescent properties of Sr4Si3O8Cl4:Eu phosphors

Sr₄Si₃O₈Cl₄: Eu²⁺ phosphors were synthesized by the solid-reaction at high temperature. The emission intensity reaches a maximum at 0.08 mol% of Eu²⁺ concentration. The present paper mainly focused on the effects of Zn²⁺ on the crystallization behavior and photoluminescence (PL) properties of Sr₄Si₃O₈Cl₄:0.08Eu²⁺. Results suggested that no new phase is introduced by co-doping with a small amount of Zn²⁺ ions, but when co-doped with excessive amount of Zn²⁺ ions, Sr₂ZnSi₂O₇ appears. We find that the co-doping of a small amount of Zn²⁺ could remarkably improve the PL intensity of Sr₄Si₃O₈Cl₄:0.08Eu²⁺. When x = 0.05, the intensity of Sr₄Si₃O₈Cl₄:0.08Eu²⁺,xZn²⁺ was increased up to 2.3 times that of pure Sr₄Si₃O₈Cl₄:0.08Eu²⁺, which could be attributed to the flux effect of Zn²⁺ ions, and the Zn²⁺ doping reduces the opportunities of the energy transfer between Eu²⁺.     

Sr3.5Mg0.5Si3O8Cl4: Eu bluish-green-emitting phosphor for NUV-based LED

Sr₄Si₃O₈Cl₄:Eu²⁺ and Sr_3.5Mg_0.5Si₃O₈Cl₄:Eu²⁺ phosphors were prepared by a conventional solid state reaction (SS). Excited by 370 nm near-ultraviolet light, the phosphors show an efficient bluish-green wide-band emission centering at 484 nm, which originates from the 4f5d¹ → 4f⁷ transition of Eu²⁺ ion. The excitation spectra of the phosphors are a broad band extending from 250 nm to 400 nm. Mg²⁺-codoping greatly enhances the bluish-green emission of the phosphors. An LED was fabricated by coating the Sr_3.5Mg_0.5Si₃O₈Cl₄:0.08Eu²⁺ phosphor onto an ~ 370 nm-emitting InGaN chip. The LED exhibits bright bluish-green emission under a forward bias of 20 mA. The results indicate that Sr_3.5Mg_0.5Si₃O₈Cl₄:0.08Eu²⁺ is a candidate as a bluish-green component for fabrication of NUV-based white LEDs.     

A novel red phosphor NaLa4(SiO4)3F: Eu

A novel red phosphor NaLa₄(SiO₄)₃F: Eu³⁺ was synthesized by the conventional solid-state reaction at 950 °C for the first time. The luminescence properties of NaLa₄(SiO₄)₃F: Eu³⁺ were investigated, and the critical concentration of the activator concentration (Eu³⁺) was found to be 0.1 mol per formula unit. The phosphor presented red luminescence under the ultraviolet excitation of 254 or 395 nm, attributed to the transitions from ⁵D₀ excited states to ⁷F_J ( J = 0-4) ground states of Eu³⁺ ions. The results indicated that this newly-developed phosphor could find applications in tricolor fluorescent lamp, phosphor-liquid crystal displays and white lighting devices utilizing GaN-based excitation in the near UV.     

(Eu-Nb)-codoped TiO2 nanopowders synthesized via Ar/O2 radio frequency thermal plasma oxidation processing: Phase composition and photoluminescence properties through energy transfer

(Eu³⁺-Nb⁵⁺)-codoped TiO₂ nanopowders have been prepared by Ar/O₂ radio frequency (RF) thermal plasma oxidizing liquid precursor mists, with various addition contents of dopants (molar ratio of Eu³⁺:Nb⁵⁺ = 1:1). Characterizations have been performed by the combined studies of XRD, TEM, Raman spectra, UV-vis spectroscopy, and excitation and PL spectra. The plasma-generated nanopowders mainly consist of anatase and rutile polymorphs. Doping Nb⁵⁺ cannot have appreciable influence on Eu³⁺ solubility (0.5 at.%) in the TiO₂ host lattice, but can significantly inhibit the increase of rutile weight fraction for TiO₂. 617 nm PL intensity at 350 nm indirect excitation through energy transfer is considerably weaker than that at 467 nm direct excitation, indicating that a defect state level in the TiO₂ host lattice might be lowered below the excited state of Eu³⁺ by doping Nb⁵⁺, which is conceivable from a relatively large amount of oxygen deficiencies yielded in the TiO₂ host lattice.     

Synthesis and luminescent properties of LaPO4:Eu microspheres

LaPO₄:Eu³⁺ microspheres were synthesized, using LaCl₃, EuCl₃ and (NH₄)₂HPO₄ as starting materials. The morphology, formation mechanism, and luminescent property of samples were systemically studied. X-ray diffraction (XRD) and infrared spectroscopy (IR) show that LaPO₄:Eu³⁺ microspheres have a pure monoclinic phase. Cetyltrimethyl ammonium bromide (CTAB) usually forms spherical micelles above a critical micelle concentration, which plays an important role in the formation of LaPO₄:Eu³⁺ microspheres. The excitation spectrum of LaPO₄:Eu³⁺ microspheres consists of several sharp lines due to the direct excitation of the Eu³⁺ cations from the ground state to higher levels of the 4f-manifold. The emission intensity of microspheres is higher than irregular particles because of the lowlier surface area. The lifetimes of Eu³⁺ ions in the LaPO₄:Eu³⁺ microspheres are determined to be 2.41 ms.     

Luminescence properties of Ca4Y6(SiO4)6O:RE (RE = Eu, Tb, Dy, Sm and Tm) under vacuum ultraviolet excitation

The vacuum ultraviolet excited luminescent properties of Eu³⁺, Tb³⁺, Dy³⁺, Sm³⁺ and Tm³⁺ in the matrices of Ca₄Y₆(SiO₄)₆O were investigated. The bands at about 173 nm in the vacuum ultraviolet excited spectra were attributed to host lattice absorption of the matrix Ca₄Y₆(SiO₄)₆O. For Eu³⁺-doped samples, the O²⁻ → Eu³⁺ CTB was identified at 258 nm. Typical 4f-5d absorption bands in the region of 195-300 nm were observed in Tb³⁺-doped samples. For Dy³⁺-doped and Sm³⁺-doped samples, the broad excitation bands consisted of host absorptions, CTB and f-d transition. For Tm³⁺-doped samples, the O²⁻ → Tm³⁺ CTB was located at 191 nm. About the color purity and emission intensity, Ca₄Y₆(SiO₄)₆O:Tb³⁺ is an attractive candidate of green light PDP phosphor, and Ca₄Y₆(SiO₄)₆O:Dy³⁺ has potential application in the field of mercury-free lamps.     

A yellow-emitting Ca3Si2O7: Eu phosphor for white LEDs

A series of yellow-emitting phosphors based on a silicate host matrix, Ca_3 − xSi₂O₇: xEu²⁺, was prepared by solid-state reaction method. The structure and photoluminescent properties of the phosphors were investigated. The XRD results show that the Eu²⁺ substitution of Ca²⁺ does not change the structure of Ca₃Si₂O₇ host and there is no impurity phase for x < 0.12. The SEM images display that phosphors aggregate obviously and the shape of the phosphor particle is irregular. The EDX results reveal that the phosphors consist of Ca, Si, O, Eu and the concentration of these elements is close to the stoichiometric composition. The Ca_3 − xSi₂O₇: xEu²⁺ phosphors can be excited at a wavelength of 300-490 nm, which is suitable for the emission band of near ultraviolet or blue light-emitting-diode (LED) chips. The phosphors exhibit a broad emission region from 520 to 650 nm and the emission peak centered at 568 nm. In addition, the shape and the position of the emission peak are not influenced by the Eu²⁺ concentration and excitation wavelength. The phosphor for x = 0.045 has the strongest excitation and emission intensity, and the Ca_3 − xSi₂O₇: xEu²⁺ phosphors can be used as candidates for the white LEDs.     

Dynamical processes of energy transfer in red emitting phosphor CaMoO4:Sm, Eu

Upon ⁴K_11/2 excitation of Sm³⁺ at 405 nm, the performance of energy transfer from Sm³⁺ to Eu³⁺ in the red emitting phosphor CaMoO₄:Eu³⁺, Sm³⁺ significantly extends its excitation region for better matching the near-UV LED. Photoluminescence spectra indicate that the energy transfer pathway concerns the relaxation from ⁴K_11/2 to ⁴G_5/2 of Sm³⁺ and subsequent transfer to ⁵D₀ of Eu³⁺ rather than ⁵D₁ of Eu³⁺. The fluorescent decay pattern of Sm³⁺⁴G_5/2 level in CaMoO₄:0.5% Sm³⁺, 2% Eu³⁺ is studied at 77 K based on the Inokuti-Hirayama formula, revealing an electronic dipole-dipole interaction between Sm³⁺ and Eu³⁺. The coefficient for the energy transfer is obtained to be 8.5 × 10⁻⁴⁰ s⁻¹ cm⁶. The fluorescence rise and decay pattern of Eu³⁺⁵D₀ level as Sm³⁺ is only excited at 77 K is well described by the dynamical processes of the energy transfer.     

Low-temperature synthesis of Y2SiO5:Eu powders using mesoporous silica and their luminescence properties

This paper reports the synthesis of Eu³⁺ ions-doped Y₂SiO₅ (Y₂SiO₅:Eu³⁺) powders by mesoporous template route. Using mesoporous silica SBA-15 as silica source, Y₂SiO₅:Eu³⁺ powders were prepared by solid-state reaction at a calcination temperature of 1300 °C without fluxes. The prepared Y₂SiO₅:Eu³⁺ powders were characterized by X-ray diffraction, scanning electron microscope, nitrogen adsorption-desorption isotherms, and photoluminescence spectroscopy. The results show that the crystalline Y₂SiO₅:Eu³⁺ particles are dense and have a morphology similar to SBA-15. The low calcination temperature is attributed to the high reactive activity of SBA-15 with large surface area and non-crystalline structure. The Y₂SiO₅:Eu³⁺ powders prepared at a low calcination temperature show luminescence properties similar to the reported results of Eu³⁺ doped-Y₂SiO₅ samples prepared at high temperatures.     

EDTA-assisted hydrothermal synthesis,characterization, and luminescent properties of YPO4·nH2O:Eu (n = 0, 0.8) microflakes and microbundles

In this paper, the YPO₄:Eu³⁺ (5%) microflakes and YPO₄·0.8H₂O:Eu³⁺ (5%) microbundles have been synthesized by a simple EDTA-assisted hydrothermal method. The X-ray powder diffraction (XRD), thermogravimetric and differential thermal analysis (TG/DTA), Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM) and photoluminescence (PL) were employed to characterize the as-obtained products. It was found that the composition of the product could be changed from YPO₄:Eu³⁺ (5%) to YPO₄·0.8H₂O:Eu³⁺ (5%) with a further increase in the amount of EDTA 0.5–1.0 g. The YPO₄:Eu³⁺ (5%) presented the pure tetragonal phase and flake-like microstructure, while the YPO₄·0.8H₂O:Eu³⁺ (5%) exhibited the hexagonal phase and bundle-like morphology. The possible formation mechanisms of the two architectures were put forward on the basis of different EDTA amount-morphology experiments. A detailed investigation on the photoluminescence of YPO₄·nH₂O:Eu³⁺ (5%) different samples indicated that the luminescent properties of products were strongly dependent on the compositions, morphologies, coordination environment and crystal field symmetry.     

Preparation of SrAl2O4: Eu, Dy nanometer phosphors by detonation method

SrAl₂O₄: Eu²⁺, Dy³⁺ nanometer phosphors were synthesized by detonation method. The particle morphology and optical properties of detonation soot that was heated at different temperatures (600–1100 °C) had been studied systematically by X-ray diffraction (XRD) and transmission electron microscopy (TEM). Results indicated SrAl₂O₄: Eu²⁺, Dy³⁺ nanometer powders in monoclinic system (a = 8.442, b = 8.822, c = 5.160, β = 93.415) can be synthesized by detonation method, when detonation soot was heated at 600–800 °C. The particle size of SrAl₂O₄: Eu²⁺, Dy³⁺ is 35 ± 15 nm. Compared with the solid-state reaction and sol-gel method, synthesis temperature of the detonation method is lower about 500 and 200 °C respectively. After being excited under UN lights, detonation soot and that heated at 600–1100 °C can emit a green light.     

Preparation and upconversion property of TeO2:Er/Yb nanoparticles

Different crystal structure of TeO₂ nanoparticles were used as the host materials to prepare the Er³⁺/Yb³⁺ ions co-doped upconversion luminescent materials. The TeO₂ nanoparticles mainly kept the original morphology and phase after having been co-doped the Er³⁺/Yb³⁺ ions. All the as-prepared TeO₂:Er³⁺/Yb³⁺ nanoparticles showed the green emissions (525 nm, 545 nm) and red emission (667 nm) under 980 nm excitation. The green emissions at 525 nm, 545 nm and red emission at 667 nm were attributed to the ²H_11/2 → ⁴I_15/2, ⁴S_3/2 → ⁴I_15/2 and ⁴F_9/2 → ⁴I_15/2 transitions of the Er³⁺ ions, respectively. For the α-TeO₂:Er³⁺/Yb³⁺ (3/10 mol%) nanoparticles, three-photon process involved in the green (²H_11/2 → ⁴I_15/2) emission, while two-photon process involved in the green (⁴S_3/2→⁴I_15/2) and red (⁴F_9/2 → ⁴I_15/2) emissions. For the β-TeO₂:Er³⁺/Yb³⁺ (3/10 mol%) nanoparticles, two-photon process involved in the green (²H_11/2 → ⁴I_15/2), green (⁴S_3/2 → ⁴I_15/2) and red (⁴F_9/2 → ⁴I_15/2) emissions. It suggested that the crystal structure of TeO₂ nanoparticles had an effect on transition processes of the Er³⁺/Yb³⁺ ions. The emission intensities of the α-TeO₂:Er³⁺/Yb³⁺ (3/10 mol%) nanoparticles and β-TeO₂:Er³⁺/Yb³⁺ (3/10 mol%) nanoparticles were much stronger than those of the (α + β)-TeO₂:Er³⁺/Yb³⁺ (3/10 mol%) nanoparticles.     

Electro-deposition of Y2O3:Eu thin film phosphor and its luminescent properties

Y₂O₃:Eu³⁺ red-emitting thin film phosphor was prepared by a two-step process: the cathodical deposition of thin film of yttrium hydroxide and europium hydroxide followed by an annealing process to achieve Eu³⁺ doped Y₂O₃ film. It is found that the atomic content of Eu³⁺ can be well controlled by simply adjusting the volume ratio of Y(NO₃)₃ to Eu(NO₃)₃ solutions. Dependence of the photoluminescence intensity on the atomic content of Eu³⁺ in Y₂O₃ was also studied. The best photoluminescence performance of Y₂O₃:Eu³⁺ thin film phosphor was achieved as atomic content of Eu³⁺ equal to 1.85 at.%.