Soft switching space vector PWM inverter using a new quasi-parallelresonant DC link

A soft switching quasi-parallel resonant DC-link (QPRDCL) inverter with improved PWM capability has been recently presented. The circuit has the minimum voltage stress of the devices and provides the flexibility of selecting the on/off instants of the resonant link, resulting in improved PWM capability. In this paper, the operational principles and the detailed analysis of the QPRDCL inverter are presented for the resonant components design and the inverter control. An SVPWM with optimal vector sequence suitable for the QPRDCL inverter is also presented through the comparisons among five different modified space vector PWM (SVPWM) techniques classified by the voltage vector sequences. The performance of the selected optimal SVPWM is verified by the experimental results     

Optimum Trajectory Switching Control for Series-Parallel Resonant Converter

The series-parallel resonant converter (SPRC) is known to have combined merits of the series resonant converter (SRC) and PRC. However, the SPRC has a three-element LCC structure with complex transient dynamics, and without control of the resonant circuit's dynamics, the converter's closed-loop bandwidth to switching-frequency ratio will be much reduced compared to that of pulsewidth-modulation (PWM) converters. This paper presents the optimal trajectory enabling any SPRC's steady state be achieved within one cycle. Dynamics using the state-plane analysis is presented, and the optimal state trajectory for transients is derived. Experimental results with comparison to frequency control show much reduced resonant circuit response time for step changes in output voltage. This improved resonant circuit control allows subsequent current and voltage-loop controls of the SPRC to be treated as that of a conventional PWM voltage source     

Resonant link bidirectional power converter. I. Resonant circuit

This paper proposes a novel resonant circuit capable of PWM operation with zero switching losses. The resonant circuit is aimed at providing zero voltage intervals in the DC link of the PWM converter during the required converter device switching periods, and it gives minimum DC bus voltage stresses and minimum peak resonant current. It requires only two additional switches compared to a conventional PWM converter. It is observed that the resonant circuit guarantees the soft switching of all the switching power devices of converters including the switches for resonant operation. Simulation results and experimental results are presented to verify the operating principles     

Parallel resonant DC link circuit-a novel zero switching losstopology with minimum voltage stresses

A parallel resonant DC link (PRDCL) circuit topology is proposed as an approach to realizing zero switching loss DC-AC high switching frequency power conversion. The proposed circuit is used as an interface between the DC voltage supply and a voltage source pulse width modulated (PWM) inverter to provide a short zero voltage period in the DC link of the inverter to allow zero voltage switchings to take place in the PWM inverter. The peak voltage stress on the PWM inverter switches is limited to the DC supply voltage. Another significant advantage of the circuit is that the inverter can be controlled by the conventional PWM strategy. The proposed circuit is systematically analyzed and its operation principle is explained. Design considerations and design formulas are presented. A complete zero voltage switching DC-AC system consisting of the proposed circuit and a PWM inverter was simulated on a computer     

A New PWM-Controlled Quasi-Resonant Converter for a High Efficiency PDP Sustaining Power Module

A new pulsewidth modulation (PWM)-controlled quasi-resonant converter for a high-efficiency plasma display panel (PDP) sustaining power module is proposed in this paper. The load regulation of the proposed converter can be achieved by controlling the ripple of the resonant voltage across the primary resonant capacitor with a bidirectional auxiliary circuit, while the main switches are operating at a fixed duty ratio and fixed switching frequency. Hence, the waveforms of the currents can be expected to be optimized from the view-point of conduction loss. Furthermore, the proposed converter has good zero-voltage switching (ZVS) capability, simple control circuits, no hign-voltage ringing problem of rectifier diodes, no dc offset of the magnetizing current and low-voltage stresses of power switches. Thus, the proposed converter shows higher efficiency than that of a half-bridge LLC resonant converter under light load condition. Although it shows the lower efficiency at heavy load, because of the increased power loss in auxiliary circuit, it still shows the high efficiency around 94%. In this paper, operational principles, features of the proposed converter, and analysis and design considerations are presented. Experimental results demonstrate that the output voltage can be controlled well by the auxiliary circuit using the PWM method.      

A new quasi-parallel resonant DC link for soft-switching PWMinverters

A new quasi-parallel resonant DC-link inverter with the more flexible pulse-width-modulation (PWM) capability and easier control is proposed in this paper. With the addition of one coupling core and one diode, the circuit can be directly applied to the single/three-phase inverter to achieve the soft-switching action. For the proposed topology, it needs neither the help of the inverter switch devices nor the requirement of voltage/current sensors. Random duration of the zero DC-link voltage can be obtained, and the voltage stresses of the inverter switches can be maintained to the minimum. The relative analysis of the presented circuit has been performed and verified by the experiment     

Analysis, designing, and experimentation of a transformer-assistedPWM zero-voltage switching pole inverter

This paper proposes a transformer-assisted pulsewidth modulation (PWM) zero-voltage switching pole inverter. As the auxiliary-resonant-commutated pole inverter (ARCPI), the proposal guarantees zero-voltage switching of the main switch and zero-current switching of the auxiliary switch, with a small power auxiliary circuit and full PWM capability. In particular, problems outstanding with the ARCPI such as control complexity, auxiliary switch protection, and center-tap potential variation, etc., are solved in the proposal. The commutation process is discussed step by step in the paper. A detailed analysis for the auxiliary circuit with regard to commutation duration/duty-cycle limitation, auxiliary switch peak current/RMS current, resonant capacitor RMS current, as well as pole output voltage loss are presented afterwards. A design methodology for the auxiliary circuit is recommended based on the analysis. The proposal is experimentally verified with a 4.25 kW half-bridge inverter prototype     

Self-commutated auxiliary circuit ZVT PWM converters

This paper introduces a novel class of zero voltage transition (ZVT) DC/DC pulse-width modulation (PWM) converters that use a resonant inductance-capacitance (L-C) circuit connected to the auxiliary switch, which is termed a self-commutated auxiliary circuit. It provides a simple and reliable means of achieving zero-current conditions (ZCS) for auxiliary switch commutations under wide line and load ranges, without the inclusion of any kind of DC voltage source. Furthermore, this auxiliary circuit is placed in parallel with the main power converter, retaining the ZVT characteristics. The self-commutated auxiliary circuit ZVT PWM boost is analyzed, and its feasibility and reliability are confirmed by experimental results obtained from laboratory prototypes rated at 1 kW and 100 kHz.     

一种同步整流DC-DC转换器PWM控制电路设计

设计了一种改进的PWM控制电路,将电流采样电路和PWM比较器归结为一个PWM电流比较器,减少了电路规模。将误差放大器输出与锯齿波斜坡补偿信号叠加,产生叠加输出电流,并通过PWM电流比较器输出一个占空比信号,以控制功率管的通断。电压信号转换为电流信号,从而使控制回路反应速度更快。将PWM控制电路应用于一款BUCK型DC-DC同步整流开关电源稳压器中。HSPICE仿真表明,稳压器输出纹波电压为±4mV,输出电压精度为±1%。     

Auxiliary resonant commutated pole inverter using two internalvoltage-points of DC source

This paper presents a new auxiliary resonant commutated pole inverter that has series-connected batteries as the DC source. This inverter has two main switches and two auxiliary switches, and of all these devices achieve soft switching. The resonant operations are employed only during the commutating intervals; therefore, pulsewidth modulation (PWM) can be applied to the circuit. This circuit has the feature of using two internal voltage points of the DC source. Consequently, the circuit has the advantages of stability, simplicity in control, and high efficiency. The principle of the circuit operation and the experimental results are described in this paper     

Interleaved soft switching resonant converter with a small input ripple current

ABSTRACT

An interleaved frequency control soft switching converter is studied for solar power or fuel cell power applications. The proposed circuit topology contains two parallel current-fed circuit cells with interleaved pulse-width modulation operation. Thus, the ripple currents at input and output terminals are decreased. In each circuit cell, the proposed current-fed dc-dc converter includes boost circuit and resonant circuit to achieve current ripple-free on low voltage side and less switching losses on active devices. The boost circuit and the resonant circuit have same active devices to decrease power switches. Due to the resonant behaviour, the reverse recovery current loss on secondary diodes is removed. The voltage doubler circuit topology is accomplished on secondary-side to reduce diode counts and conduction loss. The performance and effectiveness of the developed interleaved PWM current-fed converter are verified and confirmed by experiments.     

A new quasi-resonant DC-link PWM inverter using single switch for soft switching

This paper presents a new quasi-resonant DC-link (QRDCL) inverter. Only one switching device is used to create zero voltage instants under all load conditions. The maximum voltage across the inverter devices is maintained at around (1.01-1.1) times the input source voltage. The circuit has the flexibility of selecting switching instants of the resonant link in synchronism with any PWM technique. Control technique does not require the help of inverter switches to create the zero voltage instants in the DC-link, and voltage and current sensors are eliminated from the control circuit. In this paper, the principle of operation and detailed analysis of the proposed QRDCL inverter are presented and design considerations for achieving soft switching are obtained. Detailed PSPICE simulation studies are carried out to study the feasibility of the proposed topology under various load conditions. The experimental results of the proposed QRDCL PWM inverter feeding a three phase induction motor are given.     

New constant-frequency multiresonant boost convertor

A new zero-voltage-switching multiresonant boost convertor operating at constant switching frequency is presented. Its output voltage is regulated by controlling the freewheeling period of the resonant inductor. It possesses the advantages of a PWM convertor and frequency-modulated multiresonant convertor. Moreover, by absorbing all major parasitic components in its resonant circuit, parasitic ringing is eliminated.<>     

一种新型软开关DC-DC PWM升压变换器设计

为提高转换效率并降低电源开关的电流应力,提出一种基于新型有源缓冲电路的PWM DC-DC升压变换器。该有源缓冲电路使用ZVT—ZCT软开关技术,分别提供了总开关ZVT开启及ZCT闭合、辅助开关ZCS开启及ZCT闭合。消除了总开关额外的电流及电压应力,消除了辅助开关电压应力,且有源缓冲电路的耦合电感降低了电流应力。另外,通过连续将二极管添加到辅助开关电路,防止来自共振电路的输入电流应力进入总开关。实验结果表明,相比传统的PWM变换器,新的DC-DC PWM升压变换器在满负荷时电流应力降低且总体效率能达到98.7%。     

Current-clamped, modified series resonant DC-link power converterfor a general purpose induction motor drive

A new AC/AC power converter topology, in which all the switches operate in a resonant fashion to reduce switching losses, is proposed. The topology enables conduction-period control of individual current pulses, whereby pulse-width modulation (PWM) could be achieved to a fair degree of accuracy with the associated controller. The scheme implements current peak (resonant) limiting by a simple diode clamp. Improved switch utilization (voltage × current) and reduced part-count could be cited as the merits of the circuit over the previous soft-switched current-sourced AC/AC configurations. It is experimentally verified that the output PWM controller could be used to implement constant V/F operation, and the results are presented. In-depth design criteria for the topology that gives optimized voltage stresses are presented. A charge-based, line current feed-forward, mode-controller is introduced at the input and digitally verified. Feasibility of the simultaneous control over both input power-factor and smooth input-output line currents are studied and the digital verification is presented     

高频软开关PWM功率变换技术的发展与现状

本文介绍了三类零电压软件开关ＰＷＭ变换器和两类零电流软件开关ＰＷＭ变换器的特点和工作原理。     

A study of active power filters using quad-series voltage-sourcePWM converters for harmonic compensation

An active power filter using quad-series voltage-source pulse-width-modulated (PWM) converters to suppress AC harmonics by injecting compensating currents into the AC system is described. The circuit used to calculate the compensating current references, the compensation characteristics, and the capability of the DC capacitor are discussed theoretically and experimentally. A control circuit for the DC capacitor voltage is proposed. The discussions focus on transient states, based on the instantaneous reactive power theory. A passive LC filter is designed to remove the switching voltage and current ripples caused by the PWM converters at the AC side. Some experimental results that illustrate the details of the study are shown     

Real-time output voltage control method of quasi-ZCS seriesresonant HF-linked DC-AC converter

This paper proposes a real-time control method of a series resonant high-frequency linked DC-AC converter employing quasi-zero current switching (quasi-ZCS) and a feedback control method for sinusoidal output voltage. An approximate analysis of the converter is performed, and then simplified equations and an equivalent circuit similar to the conventional PWM inverters/inverters are obtained. A real-time feedback control of the converter is realized using the equivalent circuit without detecting HF link current. The usefulness of the proposed control algorithm is confirmed by experimental results     

High-Frequency Resonant Transistor DC-DC Converters

Transistor dc-dc converters which employ a resonant circuit are described. A resonant circuit is driven with square waves of current or voltage, and by adjusting the frequency around the resonant point, the voltage on the resonant components can be adjusted to any practical voltage level. By rectifying the voltage across the resonant elements, a dc voltage is obtained which can be either higher or lower than the input dc voltage to the converter. Thus, the converter can operate in either the step-up or step-down mode. In addition, the switching losses in the inverter devices and rectifiers are extremely low due to the sine waves that occur from the use of a resonant circuit (as opposed to square waves in a conventional converter); also, easier EMI filtering should result. In the voltage input version, the converter is able to use the parasitic diode associated with an FET or monolithic Darlington, while in the current input version, the converter needs the inverse blocking capability which can be obtained with an IGT or GTO device. A low-power breadboard operating at 200-300 kHz has been built. Two typical application areas are switching power supplies and battery chargers. The converter circuits offer improvements over conventional circuits due to their high efficiency (low switching losses), small reactive components (high-frequency operation), and their step-up/stepdown ability.     

基于高频高压交流母线多组输出直流电源的研制

本电源是基于高频高压交流母线具有多组输出的直流电源，它具有高达200kHz的开关频率，后级的整流电路由于高频交流母线的存在，使得变压器和电感的设计变得简单，滤波电容的选择也更容易。本电源由PFC电路提供400V的高压直流输入，再由MOSFET组成全桥逆变电路，在固定额率的PWM发生电路和IR2110 MOSFET驱动电路作用下，只加—个谐振电感就可实现开关管的零电压开通，可在大大降低开关损耗和噪声的同时实现直流交流的变换。整流部分采用倍流整流电路以提高原边电压的利用率，可输出低压大电流。由于采用肖特基管，—方面可使得二板管的损耗可以接受，另外—方面还避免了采用同步整流电路所面临的电路结构复杂和驱动困难。